There is a Cadence USB3 core for imx8qm and imx8qxp SoCs, the cdns
core is the child for this glue layer device.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

VBUS should be turned off when leaving the host mode.
Set GCTL_PRTCAP to device mode in teardown to de-assert DRVVBUS pin to
turn off VBUS power.

Fixes: 5f94adfe ("usb: dwc3: core: refactor mode initialization to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch includes streams implementation changes.
The current changes has been validated on FPGA platform.

Enabled streams related interrupts only for streams capable endpoints.
Processed  PRIME and IOT interrupts related to streams capable endpoints.
Based on PRIME interrupt prime_flag is set and transfer is armed
otherwise just adding request to the deferred request queue.
For streams capable endpoints preparing TD with correct stream ID.

TDL calculation:
Updated tdl calculation based on controller versions.
1. For controller version DEV_VER_V2 :We have enabled USB_CONF2_EN_TDL_TRB
   bit in usb_conf2 register in DMULT configuration.
   This enables TDL calculation based on TRB, hence setting TDL in TRB.
2. For controller Version < DEV_VER_V2 : Writing TDL and STDL in ep_cmd
   register
3. For controller version > DEV_VER_V2 : Writing TDL in ep_tdl register.

Writing ERDY with correct Stream ID to ep_cmd register.
Added stream id related information to trace logs.
Signed-off-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

drivers/usb/gadget/udc/core.c, 1175:
	kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
	usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
	usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
	spin_lock in gr_probe

drivers/usb/gadget/udc/core.c, 1195:
	mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
	usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
	usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
	spin_lock in gr_probe

drivers/usb/gadget/udc/gr_udc.c, 212:
	debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
	gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
    spin_lock in gr_probe

drivers/usb/gadget/udc/gr_udc.c, 2114:
	devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
	gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
    spin_lock in gr_probe

kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.

To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.

These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The UDC core uses req->num_sgs to judge if scatter buffer list is used.
Eg: usb_gadget_map_request_by_dev. For f_fs sync io mode, the request
is re-used for each request, so if the 1st request->length > PAGE_SIZE,
and the 2nd request->length is <= PAGE_SIZE, the f_fs uses the 1st
req->num_sgs for the 2nd request, it causes the UDC core get the wrong
req->num_sgs value (The 2nd request doesn't use sg). For f_fs async
io mode, it is not harm to initialize req->num_sgs as 0 either, in case,
the UDC driver doesn't zeroed request structure.

Cc: Jun Li <jun.li@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 772a7a72 ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some functions support speeds other than SuperSpeed. Add max_speed
attribute to configfs gadget allowing user to specify the maximum speed
the composite driver supports. The valid input speed names are
super-speed-plus, super-speed, high-speed, full-speed, and low-speed.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If we do not warn here, the user may not know failed to
find udc device by a gadget driver with the same name
because it silently fails. Let's print a warning in that
case so developers find these problems faster.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These interfaces do support super-speed so let's not
limit maximum speed to high-speed.

Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The number of FIFOs may be lower than the number of endpoints.  Use the
correct total when printing FIFO details in debugfs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On chips with fewer FIFOs than endpoints (for example RK3288 which has 9
endpoints, but only 6 which are cabable of input), the DPTXFSIZN
registers above the FIFO count may return invalid values.

With logging added on startup, I see:

	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=1 sz=256
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=2 sz=128
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=3 sz=128
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=4 sz=64
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=5 sz=64
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=6 sz=32
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=7 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=8 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=9 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=10 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=11 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=12 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=13 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=14 sz=0
	dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=15 sz=0

but:

	# cat /sys/kernel/debug/ff580000.usb/fifo
	Non-periodic FIFOs:
	RXFIFO: Size 275
	NPTXFIFO: Size 16, Start 0x00000113

	Periodic TXFIFOs:
		DPTXFIFO 1: Size 256, Start 0x00000123
		DPTXFIFO 2: Size 128, Start 0x00000223
		DPTXFIFO 3: Size 128, Start 0x000002a3
		DPTXFIFO 4: Size 64, Start 0x00000323
		DPTXFIFO 5: Size 64, Start 0x00000363
		DPTXFIFO 6: Size 32, Start 0x000003a3
		DPTXFIFO 7: Size 0, Start 0x000003e3
		DPTXFIFO 8: Size 0, Start 0x000003a3
		DPTXFIFO 9: Size 256, Start 0x00000123

so it seems that FIFO 9 is mirroring FIFO 1.

Fix the allocation by using the FIFO count instead of the endpoint count
when selecting a FIFO for an endpoint.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The last user of the phy generic platform data was
deleted in commit 1e041b6f
("usb: dwc3: exynos: Remove dead code"). So get rid of
the platform data, which rids us of another consumer of
the legacy GPIO API at the same time. Make sure we
only inlcude <linux/gpio/consumer.h> which is all we use.

Alter the usb_phy_gen_create_phy() function prototype to
not pass any platform data as this is just hardcoded to
NULL at all locations calling it in the kernel.

Move the devm_gpiod_get* calls out of the if (of_node)
parenthesis, as these calls are generic and do not depend
on device tree, they are used by any hardware description.

Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a usb device disconnects in a certain way, dwc2_queue_transaction
still gets called after dwc2_hcd_cleanup_channels.

dwc2_hcd_cleanup_channels does "channel->qh = NULL;" but
dwc2_queue_transaction still wants to dereference qh.
This adds a check for a null qh.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
[dianders: rebased to mainline]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Stalling a Non-Isochronous OUT Endpoint flow changed according
programming guide.
In dwc2_hsotg_ep_sethalt() function for OUT EP should not be set STALL bit.
Instead should set SGOUTNAK in DCTL register. Set STALL bit should be
set only after GOUTNAKEFF interrupt asserted.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Send a no-action link state change request before the actual request
so DWC3 can send the same request whenever we call
dwc3_gadget_set_link_state().
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When DWC3 receives disconnect event, it needs to set the link state to
RX_Detect.

DWC_usb3 3.30a programming guide 4.1.7
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DCTL.ULSTCHNGREQ is a write-only field. When doing a read-modify-write
to DCTL, the driver must make sure that there's no unintended link state
change request from whatever is read from DCTL.ULSTCHNGREQ. Set link
state change to no-action when the driver writes to DCTL.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the case where the call tb_switch_exceeds_max_depth is true
the error reurn path leaks memory in sw.  Fix this by setting
the return error code to -EADDRNOTAVAIL and returning via the
error exit path err_free_sw_ports to free sw. sw has been kzalloc'd
so the free of the NULL sw->ports is fine.

Addresses-Coverity: ("Resource leak")
Fixes: b0407983 ("thunderbolt: Add initial support for USB4")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191220220526.11307-1-colin.king@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull RISC-V fixes from Paul Walmsley:
 "Two fixes for RISC-V:

   - Clear FP registers during boot when FP support is present, rather
     than when they aren't present

   - Move the header files associated with the SiFive L2 cache
     controller to drivers/soc (where the code was recently moved)"

* tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Fixup obvious bug for fp-regs reset
  riscv: move sifive_l2_cache.h to include/soc

CSR_MISA is defined in Privileged Architectures' spec: 3.1.1 Machine
ISA Register misa. Every bit:1 indicate a feature, so we should beqz
reset_done when there is no F/D bit in csr_misa register.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
[paul.walmsley@sifive.com: fix typo in commit message]
Fixes: 9e806356 ("riscv: clear the instruction cache and all registers when booting")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

The commit 9209fb51 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb51 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

Pull iommu fixes from Joerg Roedel:

 - Two fixes for VT-d and generic IOMMU code to fix teardown on error
   handling code paths.

 - Patch for the Intel VT-d driver to fix handling of non-PCI devices

 - Fix W=1 compile warning in dma-iommu code

* tag 'iommu-fixes-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/dma: fix variable 'cookie' set but not used
  iommu/vt-d: Unlink device if failed to add to group
  iommu: Remove device link to group on failure
  iommu/vt-d: Fix adding non-PCI devices to Intel IOMMU

Pull i2c fixes from Wolfram Sang:
 "Two driver bugfixes, a documentation fix, and a removal of a spec
  violation for the bus recovery algorithm in the core"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: fix bus recovery stop mode timing
  i2c: bcm2835: Store pointer to bus clock
  dt-bindings: i2c: at91: fix i2c-sda-hold-time-ns documentation for sam9x60
  i2c: at91: fix clk_offset for sam9x60

Pull thread fixes from Christian Brauner:
 "This contains a series of patches to fix CLONE_SETTLS when used with
  clone3().

  The clone3() syscall passes the tls argument through struct clone_args
  instead of a register. This means, all architectures that do not
  implement copy_thread_tls() but still support CLONE_SETTLS via
  copy_thread() expecting the tls to be located in a register argument
  based on clone() are currently unfortunately broken. Their tls value
  will be garbage.

  The patch series fixes this on all architectures that currently define
  __ARCH_WANT_SYS_CLONE3. It also adds a compile-time check to ensure
  that any architecture that enables clone3() in the future is forced to
  also implement copy_thread_tls().

  My ultimate goal is to get rid of the copy_thread()/copy_thread_tls()
  split and just have copy_thread_tls() at some point in the not too
  distant future (Maybe even renaming copy_thread_tls() back to simply
  copy_thread() once the old function is ripped from all arches). This
  is dependent now on all arches supporting clone3().

  While all relevant arches do that now there are still four missing:
  ia64, m68k, sh and sparc. They have the system call reserved, but not
  implemented. Once they all implement clone3() we can get rid of
  ARCH_WANT_SYS_CLONE3 and HAVE_COPY_THREAD_TLS.

  This series also includes a minor fix for the arm64 uapi headers which
  caused __NR_clone3 to be missing from the exported user headers.

  Unfortunately the series came in a little late especially given that
  it touches a range of architectures. Due to the holidays not all arch
  maintainers responded in time probably due to their backlog. Will and
  Arnd have thankfully acked the arm specific changes.

  Given that the changes are straightforward and rather minimal combined
  with the fact the that clone3() with CLONE_SETTLS is broken I decided
  to send them post rc3 nonetheless"

* tag 'clone3-tls-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  um: Implement copy_thread_tls
  clone3: ensure copy_thread_tls is implemented
  xtensa: Implement copy_thread_tls
  riscv: Implement copy_thread_tls
  parisc: Implement copy_thread_tls
  arm: Implement copy_thread_tls
  arm64: Implement copy_thread_tls
  arm64: Move __ARCH_WANT_SYS_CLONE3 definition to uapi headers

Pull HID fix from Jiri Kosina:
 "A regression fix for EPOLLOUT handling in hidraw and uhid"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: hidraw, uhid: Always report EPOLLOUT

Pull USB/PHY fixes from Greg KH:
 "Here are a number of USB and PHY driver fixes for 5.5-rc6

  Nothing all that unusual, just the a bunch of small fixes for a lot of
  different reported issues. The PHY driver fixes are in here as they
  interacted with the usb drivers.

  Full details of the patches are in the shortlog, and all of these have
  been in linux-next with no reported issues"

* tag 'usb-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (24 commits)
  usb: missing parentheses in USE_NEW_SCHEME
  usb: ohci-da8xx: ensure error return on variable error is set
  usb: musb: Disable pullup at init
  usb: musb: fix idling for suspend after disconnect interrupt
  usb: typec: ucsi: Fix the notification bit offsets
  USB: Fix: Don't skip endpoint descriptors with maxpacket=0
  USB-PD tcpm: bad warning+size, PPS adapters
  phy/rockchip: inno-hdmi: round clock rate down to closest 1000 Hz
  usb: chipidea: host: Disable port power only if previously enabled
  usb: cdns3: should not use the same dev_id for shared interrupt handler
  usb: dwc3: gadget: Fix request complete check
  usb: musb: dma: Correct parameter passed to IRQ handler
  usb: musb: jz4740: Silence error if code is -EPROBE_DEFER
  usb: udc: tegra: select USB_ROLE_SWITCH
  USB: core: fix check for duplicate endpoints
  phy: cpcap-usb: Drop extra write to usb2 register
  phy: cpcap-usb: Improve host vs docked mode detection
  phy: cpcap-usb: Prevent USB line glitches from waking up modem
  phy: mapphone-mdm6600: Fix uninitialized status value regression
  phy: cpcap-usb: Fix flakey host idling and enumerating of devices
  ...

Pull char/misc fix from Greg KH:
 "Here is a single fix, for the chrdev core, for 5.5-rc6

  There's been a long-standing race condition triggered by syzbot, and
  occasionally real people, in the chrdev open() path. Will finally took
  the time to track it down and fix it for real before the holidays.

  Here's that one patch, it's been in linux-next for a while with no
  reported issues and it does fix the reported problem"

* tag 'char-misc-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  chardev: Avoid potential use-after-free in 'chrdev_open()'

Pull staging fixes from Greg KH:
 "Here are some small staging driver fixes for 5.5-rc6.

  Nothing major here, just some small fixes for a comedi driver, the
  vt6656 driver, and a new device id for the rtl8188eu driver.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: rtl8188eu: Add device code for TP-Link TL-WN727N v5.21
  staging: comedi: adv_pci1710: fix AI channels 16-31 for PCI-1713
  staging: vt6656: set usb_set_intfdata on driver fail.
  staging: vt6656: remove bool from vnt_radio_power_on ret
  staging: vt6656: limit reg output to block size
  staging: vt6656: correct return of vnt_init_registers.
  staging: vt6656: Fix non zero logical return of, usb_control_msg

Pull tty/serial fixes from Greg KH:
 "Here are two tty/serial driver fixes for 5.5-rc6.

  The first fixes a much much reported issue with a previous tty port
  link patch that is in your tree, and the second fixes a problem where
  the serdev driver would claim ACPI devices that it shouldn't be
  claiming.

  Both have been in linux-next for a while with no reported issues"

* tag 'tty-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serdev: Don't claim unsupported ACPI serial devices
  tty: always relink the port

Pull block fixes from Jens Axboe:
 "A few fixes that should go into this round.

  This pull request contains two NVMe fixes via Keith, removal of a dead
  function, and a fix for the bio op for read truncates (Ming)"

* tag 'block-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
  nvmet: fix per feat data len for get_feature
  nvme: Translate more status codes to blk_status_t
  fs: move guard_bio_eod() after bio_set_op_attrs
  block: remove unused mp_bvec_last_segment

Pull io_uring fix from Jens Axboe:
 "Single fix for this series, fixing a regression with the short read
  handling.

  This just removes it, as it cannot safely be done for all cases"

* tag 'io_uring-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
  io_uring: remove punt of short reads to async context

Pull MTD fixes from Miquel Raynal:
 "MTD:
   - sm_ftl: Fix NULL pointer warning.

  Raw NAND:
   - Cadence: fix compile testing.
   - STM32: Avoid locking.

  Onenand:
   - Fix several sparse/build warnings.

  SPI-NOR:
   - Add a flag to fix interaction with Micron parts"

* tag 'mtd/fixes-for-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
  mtd: spi-nor: Fix the writing of the Status Register on micron flashes
  mtd: sm_ftl: fix NULL pointer warning
  mtd: onenand: omap2: Pass correct flags for prep_dma_memcpy
  mtd: onenand: samsung: Fix iomem access with regular memcpy
  mtd: onenand: omap2: Fix errors in style
  mtd: cadence: Fix cast to pointer from integer of different size warning
  mtd: rawnand: stm32_fmc2: avoid to lock the CPU bus

Pull sound fixes from Takashi Iwai:
 "A few piled ASoC fixes and usual HD-audio and USB-audio fixups. Some
  of them are for ASoC core error-handling"

* tag 'sound-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda: enable regmap internal locking
  ALSA: hda/realtek - Add quirk for the bass speaker on Lenovo Yoga X1 7th gen
  ALSA: hda/realtek - Set EAPD control to default for ALC222
  ALSA: usb-audio: Apply the sample rate quirk for Bose Companion 5
  ALSA: hda/realtek - Add new codec supported for ALCS1200A
  ASoC: Intel: boards: Fix compile-testing RT1011/RT5682
  ASoC: SOF: imx8: Fix dsp_box offset
  ASoC: topology: Prevent use-after-free in snd_soc_get_pcm_runtime()
  ASoC: fsl_audmix: add missed pm_runtime_disable
  ASoC: stm32: spdifrx: fix input pin state management
  ASoC: stm32: spdifrx: fix race condition in irq handler
  ASoC: stm32: spdifrx: fix inconsistent lock state
  ASoC: core: Fix access to uninitialized list heads
  ASoC: soc-core: Set dpcm_playback / dpcm_capture
  ASoC: SOF: imx8: fix memory allocation failure check on priv->pd_dev
  ASoC: SOF: Intel: hda: hda-dai: fix oops on hda_link .hw_free
  ASoC: SOF: fix fault at driver unload after failed probe

Pull thermal fix from Daniel Lezcano:
 "Fix backward compatibility with old DTBs on QCOM tsens (Amit
  Kucheria)"

* tag 'thermal-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
  drivers: thermal: tsens: Work with old DTBs

Pull power management fixes from Rafael Wysocki:
 "Prevent the cpufreq-dt driver from probing Tegra20/30 (Dmitry
  Osipenko) and prevent the Intel RAPL power capping driver from
  crashing during CPU initialization due to a NULL pointer dereference
  if the processor model in use is not known to it (Harry Pan)"

* tag 'pm-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  powercap: intel_rapl: add NULL pointer check to rapl_mmio_cpu_online()
  cpufreq: dt-platdev: Blacklist NVIDIA Tegra20 and Tegra30 SoCs

The existing implementation for the get_feature admin-cmd does not
use per-feature data len. This patch introduces a new helper function
nvmet_feat_data_len(), which is used to calculate per feature data len.
Right now we only set data len for fid 0x81 (NVME_FEAT_HOST_ID).

Fixes: commit e9061c39 ("nvmet: Remove the data_len field from the nvmet_req struct")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Amit Engel <amit.engel@dell.com>
[endiness, naming, and kernel style fixes]
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Decode interrupted command and not ready namespace nvme status codes to
BLK_STS_TARGET. These are not generic IO errors and should use a non-path
specific error so that it can use the non-failover retry path.
Reported-by: John Meneghini <John.Meneghini@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: be54e746 ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll")
Fixes: 9f3b61dc ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

* powercap:
  powercap: intel_rapl: add NULL pointer check to rapl_mmio_cpu_online()