Instead of implementing practically the same
function (hwaddr_aton) use mac_pton.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The userspace may want to know what is the current ssid that a given
interface is using. This patch enables nl80211 to send the
NL80211_ATTR_SSID attribute in nl80211_send_iface().
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Store the configured ssid in wdev->ssid when starting an AP
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Parsing the P2P attributes can be tricky as their
contents can be split across multiple (vendor) IEs.
Thus, it's not possible to parse them like IEs (by
returning a pointer to the data.) Instead, provide
a function that copies the attribute data into a
caller-provided buffer and returns the size needed
(useful in case the buffer was too small.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The commit:

commit 5e760230
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Nov 4 11:18:17 2011 +0100

    cfg80211: allow registering to beacons

allowed only a single process to register for beacon events
per wiphy.  This breaks cases where a user may want two or
more VIFs on a wiphy and run a seperate hostapd process on
each vif.

This patch allows multiple beacon listeners, fixing the
regression.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This new callback can be used to tune the rate to be used to send
multicast frames.

In the current state the multicast rate can be specified on IBSS/MESH
joining only. This makes it impossible to select a custom multicast
rate when then join command is sent by an external program (e.g.
wpa_supplicant)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This command triggers a new callback: set_mcast_rate(). It enables
the user to change the rate used to send multicast frames for vif
configured as IBSS or MESH_POINT
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The Peer-to-Peer IE is vendor-specific IE identified by WiFi Alliance
OUI and specific P2P OUI type. The payload of this IE consists of
so-called P2P attributes. This patch adds definitions for processing
these attributes.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When userspace asks to deauthenticate and we're just
authenticated (or still authenticating) send a deauth
frame instead of deleting the auth request.

On the other hand, if we've just disassociated and
therefore deleted all our state already, drop the
deauth request because we no longer have a channel
context to send it on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of using the pointer which can be re-used
fairly quickly due to allocator patterns and then
makes debugging difficult, maintain a counter and
use its value. Since it's a 64-bit value it can't
really wrap, but catch that case anyway since it
most likely points to a bug somewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The TX status reporting is done for both the
nl80211 report as well as the socket option.
The socket option is also reported when an
skb is dropped to guarantee that the copy in
the IDR tree is freed and status is reported
to userspace.

However, when a frame is dropped, no nl80211
status is reported. This can cause userspace
to stop making progress while waiting for a
status notification.

Combine the nl80211 and socket option status
reporting into a new function and call it in
both places -- when the status comes in from
the driver and when the skb is dropped.

While at it, also simplify the code in the
nl80211 portion a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Just for debugging, print the interface TX
power whenever it changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.

Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Setting the wdev to NULL when the channel can't be
set for that interface type (to treat the channel
setting for the wiphy/monitor) currently works, but
is confusing in the code if netdev/wdev aren't both
set/unset in the same way. Move the check whether
the channel can be set to where it's needed so that
wdev and netdev are always both assigned or NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To use mac80211_hwsim for testing channel contexts it
has to support them, and for that it has to support
hw scan and hw-remain-on-channel.

Since it's pure software, the off-channel activities
are really not off-channel but listening and sending
on a second channel. Also, the multi-channel isn't
really doing TDM, it's just on both channels at the
same time.

For testing purposes, you can specify the number of
concurrent channels with a module parameter, it is
set to one by default. When set to two or more, the
userspace API for wmediumd is disabled as it has no
provisions for multi-channel yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Conflicts:
	drivers/net/wireless/mwifiex/cfg80211.c

The BCM43222 with the chipid 43222 or 0xa8d6 in hex do not need any
special handling in the pmu code. This prevents some error messages
being shown.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

14e4:4350 is found on a Broadcom BCM43222.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reduced the power consumption to half in full and network sleep.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reduced the power consumption to half in full and network sleep.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This driver is for the AR5523 chipset from Atheros. It was created
in 2007 by Christoph Hellwig but it was never finished. I found it a
couple of months ago and after some polishing it's working pretty
fine.

The driver was written with the FreeBSD driver (uath) as reference,
which was written with the reverse-engineered windows driver as
reference, hence the feature set is very limited. Station mode
only, no HW crypto offload.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For AP feature the IEs are stored in global structure. For future
functionality like P2P-GO it needs to be stored per virtual interface
so better store it in the virtual interface structure.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The macro wiphy_to_cfg() is a bit redundant as the function already
has a pointer variable to brcmf_cfg80211_info structure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With multiple interfaces suspend will need to iterate over all and
bring down the link.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver had a global constant ether_bcast, which was copied
whenever a broadcast mac address was needed. This patch does a
memset(dest, 0xFF, ETH_ALEN) instead and consequently removes
the global ether_bcast.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The function now return the status for a virtual interface so
it seems better rename the function to understand what it does.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The enumeration wl_prof_list is no longer used so it can be safely
removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A couple of unused fields have been removed and kernel-doc info has
been added to the structure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In wl_cfg80211.c debugfs directory was created to expose
dtim_period and beacon_interval. However, this can be easily
obtained using iw so it is removed from the driver.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The connection status is to be kept per virtual interface and
the scanning status is for device. So they need to be separated
for multiple interface support.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This checks the status that will soon be moved to virtual
interface data so preparing for that use the structure
brcmf_cfg80211_vif as parameter instead.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meulemen <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The profile information applies to an interface so each virtual
interface needs it. So it is removed from brcmf_cfg80211_info
and added to brcmf_cfg80211_vif structure.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch introduces the brcmf_cfg80211_vif structure which is
used to keep track of multiple virtual interfaces in the driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The function brcmf_find_bssidx() is no longer used so remove
it from the driver code.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>