- 15 Nov, 2022 6 commits
-
-
Tony Lindgren authored
There are 8 general purpose timers on am65 that can be used for things like PWM using pwm-omap-dmtimer driver. There are also additional four timers in the MCU domain that do not have interrupts routable for Linux. We configure the timers with the 25 MHz input clock by default as the 32.768 kHz clock may not be wired on the device. We leave the MCU domain timers clock mux unconfigured, and mark the MCU domain timers reserved. The MCU domain timers are likely reserved by the software for the ESM module. Compared to am65, the timers on am62 do not have a dedicated IO mux for the timers. On am62, the timers have different interrupts, clocks and power domains compared to am65, and the MCU timers are at a different IO address. Cc: Keerthy <j-keerthy@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Nishanth Menon <nm@ti.com> Reviewed-by:
Georgi Vlaev <g-vlaev@ti.com> Link: https://lore.kernel.org/r/20221115154842.7755-4-tony@atomide.com
-
Tony Lindgren authored
There are 12 general purpose timers on am65 that can be used for things like PWM using pwm-omap-dmtimer driver. There are also additional four timers in the MCU domain that do not have interrupts routable for Linux. We configure the timers with the 25 MHz input clock by default as the 32.768 kHz clock may not be wired on the device. We leave the MCU domain timers clock mux unconfigured, and mark the MCU domain timers reserved. The MCU domain timers are likely reserved by the software for the ESM module. Compared to am64, the timer clocks are different on am65. And the MCU timers are at a different IO address. Then j72 adds more timers compared to am65 with a total of 30 timers. And the j72 clocks are different. To avoid duplication for dtsi files, eventually we may want to consider adding timer specific shared dtsi files with the timer clocks mapped using SoC specific files in include/dt-bindings/clock. But let's get am65 timers usable first. Cc: Keerthy <j-keerthy@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by:
-
Tony Lindgren authored
Compared to the earlier TI SoCs, am65 has an additional level of dedicated multiplexing registers for the timer IO pads. There are timer IO pads in the MCU domain, and in the MAIN domain. These pads can be muxed for the related timers. There are timer IO control registers for input and output. The registers for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and CTRLMMR_MCU_TIMERIO*_CTRL the output. The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the CASCADE_EN bit is documented in TRM "12.8.3.1 Timers Overview". For chaining timers, the timer IO control registers also have a CASCADE_EN input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit muxes the previous timer output, or possibly and external TIMER_IO pad source, to the input clock of the selected timer instance for odd numered timers. For the even numbered timers, the CASCADE_EN bit does not do anything. The timer cascade input routing options are shown in TRM "Figure 12-3632. Timers Overview". For handling beyond multiplexing, the driver support for timer cascading should be likely be handled via the clock framework. Cc: Keerthy <j-keerthy@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Hex numbers in addresses and sizes should be rather eight digits, not nine. Drop leading zeros. No functional change (same DTB). Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Rahul T R authored
Add pinmux required to bring out i2c5 and gpios on 40 pin RPi header on sk board Signed-off-by:
Sinthu Raja <sinthu.raja@ti.com> Signed-off-by:
Rahul T R <r-ravikumar@ti.com> Signed-off-by:
-
Vijay Pothukuchi authored
Add dts nodes for 6 EHRPWM instances on SoC. Disable EHRPWM nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Includes a minor formatting fixup for the serdes node to line up the nodes appropriately. Signed-off-by:
Vijay Pothukuchi <vijayp@ti.com> Signed-off-by:
-
- 04 Nov, 2022 11 commits
-
-
Andrew Davis authored
McASP nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the McASP nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
Andrew Davis <afd@ti.com> Signed-off-by:
Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by:
Bryan Brattlof <bb@ti.com> Link: https://lore.kernel.org/r/20221028142417.10642-12-afd@ti.com
-
Andrew Davis authored
Mailbox nodes defined in the top-level AM65x SoC dtsi files are incomplete and may not be functional unless they are extended with a chosen interrupt and connection to a remote processor. As the remote processors depend on memory nodes which are only known at the board integration level, these nodes should only be enabled when provided with the above information. Disable the Mailbox nodes in the dtsi files and only enable the ones that are actually used on a given board. Signed-off-by:
-
Andrew Davis authored
PCIe nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with a SerDes PHY. And usually only one of the two modes can be used at a time as they share a SerDes link. As the PHY and mode is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the PCIe nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
MCAN nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the MCAN nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
MDIO nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with a pinmux. As the attached PHY is only known about at the board integration level, these nodes should only be enabled when provided with this information. Disable the MDIO nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
Although usually integrated as a child of an Ethernet controller, MDIO IP has an independent pinout. This pinout should be controlled by the MDIO node (so if it was to be disabled for instance, the pinmux state would reflect that). Move the MDIO pins pinmux to the MIDO nodes. Signed-off-by:
-
Andrew Davis authored
ECAP nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. (These and the EPWM nodes could be used to trigger internal actions but they are not used like that currently) As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the ECAP nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
EPWM nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the EPWM nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
SPI nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the SPI nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
I2C nodes defined in the top-level AM65x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the I2C nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
UART nodes defined in the top-level AM65x SoC dtsi files are incomplete and may not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the UART nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
- 03 Nov, 2022 1 commit
-
-
Matt Ranostay authored
Avoid the following warnings from dt-schema by just renaming the clock-names string from adc_tsc_fck to fck so it matches the values in ti,am3359-tscadc.yaml tscadc@40200000: clock-names:0: 'fck' was expected Signed-off-by:
Matt Ranostay <mranostay@ti.com> Signed-off-by:
Judith Mendez <jm@ti.com> Reviewed-by:
Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20221024151648.394623-1-mranostay@ti.com
-
- 28 Oct, 2022 22 commits
-
-
Andrew Davis authored
I2C nodes defined in the top-level J721s2 SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the I2C nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
MCAN nodes defined in the top-level J721s2 SoC dtsi files are incomplete and may not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the MCAN nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
Mailbox nodes defined in the top-level J721s2 SoC dtsi files are incomplete and may not be functional unless they are extended with a chosen interrupt and connection to a remote processor. As the remote processors depend on memory nodes which are only known at the board integration level, these nodes should only be enabled when provided with the above information. Disable the Mailbox nodes in the dtsi files and only enable the ones that are actually used on a given board. Signed-off-by:
-
Andrew Davis authored
Mailbox nodes defined in the top-level J7200 SoC dtsi files are incomplete and may not be functional unless they are extended with a chosen interrupt and connection to a remote processor. As the remote processors depend on memory nodes which are only known at the board integration level, these nodes should only be enabled when provided with the above information. Disable the Mailbox nodes in the dtsi files and only enable the ones that are actually used on a given board. Signed-off-by:
-
Andrew Davis authored
Mailbox nodes defined in the top-level J721e SoC dtsi files are incomplete and may not be functional unless they are extended with a chosen interrupt and connection to a remote processor. As the remote processors depend on memory nodes which are only known at the board integration level, these nodes should only be enabled when provided with the above information. Disable the Mailbox nodes in the dtsi files and only enable the ones that are actually used on a given board. Signed-off-by:
-
Andrew Davis authored
UART nodes defined in the top-level J721s2 SoC dtsi files are incomplete and may not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the UART nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
I2C nodes defined in the top-level J7200 SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the I2C nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
UART nodes defined in the top-level J7200 SoC dtsi files are incomplete and may not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the UART nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
MCAN nodes defined in the top-level J721e SoC dtsi files are incomplete and may not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the MCAN nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
MCASP nodes defined in the top-level J721e SoC dtsi files are incomplete and may not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the MCASP nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
I2C nodes defined in the top-level J721e SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the I2C nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
UART nodes defined in the top-level J721e SoC dtsi files are incomplete and may not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the UART nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
OSPI nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the OSPI nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
SDHCI nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the SDHCI nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
MCAN nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the MCAN nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
MDIO nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with a pinmux. As the attached PHY is only known about at the board integration level, these nodes should only be enabled when provided with this information. Disable the MDIO nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
Although usually integrated as a child of an Ethernet controller, MDIO IP has an independent pinout. This pinout should be controlled by the MDIO node (so if it was to be disabled for instance, the pinmux state would reflect that). Move the MDIO pins pinmux to the MIDO nodes. Signed-off-by:
-
Andrew Davis authored
ECAP nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. (These and the EPWM nodes could be used to trigger internal actions but they are not used like that currently) As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the ECAP nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
EPWM nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the EPWM nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
SPI nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the SPI nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
I2C nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the I2C nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
Andrew Davis authored
UART nodes defined in the top-level AM62x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information. Disable the UART nodes in the dtsi files and only enable the ones that are actually pinned out on a given board. Signed-off-by:
-
