- 21 Sep, 2015 35 commits
-
-
Krzysztof Kozlowski authored
commit e323d56e upstream. The TSADC gate clock was used in Exynos4x12 DTSI for exynos-adc driver. However TSADC is present only on Exynos4210 so on Trats2 board (with Exynos4412 SoC) the exynos-adc driver could not be probed: ERROR: could not get clock /adc@126C0000:adc(0) exynos-adc 126c0000.adc: failed getting clock, err = -2 exynos-adc: probe of 126c0000.adc failed with error -2 Instead on Exynos4x12 SoCs the main clock used by Analog to Digital Converter is located in different register and it is named in datasheet as PCLK_ADC. Regardless of the name the purpose of this PCLK_ADC clock is the same as purpose of TSADC from Exynos4210. The patch adds gate clock for Exynos4x12 using the proper register so backward compatibility is preserved. This fixes the probe of exynos-adc driver on Exynos4x12 boards and allows accessing sensors connected to it on Trats2 board (ntc,ncp15wb473 AP and battery thermistors). Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: c63c5743 ("ARM: dts: Add ADC's dt data to read raw data for exynos4x12") Reviewed-by:
Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by:
Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Heiko Stuebner authored
commit 4791eb61 upstream. The dwmac ethernet controller on the rk3288 supports phys connected via rgmii and rmii. With rgmii phys it is expected that the mac clock is provided externally while with rmii phys the clock can be external but also generated from the plls. In the later case it of course needs be at 50MHz, which gets set from the dwmac_rk driver. As most devices use a rgmii phy it never surfaced so far that the mac clk mux, doesn't go up one lever to the pll clock in the rmii case with internal clock generation, as it is missing the CLK_SET_RATE_PARENT flag, and thus will not set the correct frequency in most cases. Fixes: b9e4ba54 ("clk: rockchip: add clock controller for rk3288") Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Colin Ian King authored
commit f4745a92 upstream. Static analysis by cppcheck found an issue that was recently introduced by commit 471f7707 ("PM / clock_ops: make __pm_clk_enable more generic") where a return status in ret was not being initialised and garbage being returned when ce->status >= PCE_STATUS_ERROR. The fact that ret is not being checked by the caller and that ret is only used internally __pm_clk_enable() to check if clk_enable() was OK means we can ignore returning it instead turn __pm_clk_enable() into function with a void return. Fixes: 471f7707 ("PM / clock_ops: make __pm_clk_enable more generic") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
David Kershner authored
commit 1fc07f99 upstream. We inadvertently remove the MODULE_DEVICE_TABLE line for visorbus, this patch adds it back in. Signed-off-by:
David Kershner <david.kershner@unisys.com> Signed-off-by:
Benjamin Romer <benjamin.romer@unisys.com> Fixes: d5b3f1dc ('staging: unisys: move timskmod.h functionality') Signed-off-by:
-
Ian Abbott authored
commit c04a1f17 upstream. `devpriv->ao_timer` is used while an asynchronous command is running on the AO subdevice. It also gets modified by the subdevice's `cmdtest` handler for checking new asynchronous commands, `usbduxsigma_ao_cmdtest()`, which is not correct as it's allowed to check new commands while an old command is still running. Fix it by moving the code which sets up `devpriv->ao_timer` into the subdevice's `cmd` handler, `usbduxsigma_ao_cmd()`. Note that the removed code in `usbduxsigma_ao_cmdtest()` checked that `devpriv->ao_timer` did not end up less that 1, but that could not happen due because `cmd->scan_begin_arg` or `cmd->convert_arg` had already been range-checked. Also note that we tested the `high_speed` variable in the old code, but that is currently always 0 and means that we always use "scan" timing (`cmd->scan_begin_src == TRIG_TIMER` and `cmd->convert_src == TRIG_NOW`) and never "convert" (individual sample) timing (`cmd->scan_begin_src == TRIG_FOLLOW` and `cmd->convert_src == TRIG_TIMER`). The moved code tests `cmd->convert_src` instead to decide whether "scan" or "convert" timing is being used, although currently only "scan" timing is supported. Fixes: fb1ef622 ("staging: comedi: usbduxsigma: tidy up analog output command support") Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Reviewed-by:
Bernd Porr <mail@berndporr.me.uk> Reviewed-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by:
-
Ian Abbott authored
commit 423b24c3 upstream. `devpriv->ai_timer` is used while an asynchronous command is running on the AI subdevice. It also gets modified by the subdevice's `cmdtest` handler for checking new asynchronous commands (`usbduxsigma_ai_cmdtest()`), which is not correct as it's allowed to check new commands while an old command is still running. Fix it by moving the code which sets up `devpriv->ai_timer` and `devpriv->ai_interval` into the subdevice's `cmd` handler, `usbduxsigma_ai_cmd()`. Note that the removed code in `usbduxsigma_ai_cmdtest()` checked that `devpriv->ai_timer` did not end up less than than 1, but that could not happen because `cmd->scan_begin_arg` had already been checked to be at least the minimum required value (at least when `cmd->scan_begin_src == TRIG_TIMER`, which had also been checked to be the case). Fixes: b986be85 ("staging: comedi: usbduxsigma: tidy up analog input command support) Signed-off-by:
-
Ian Abbott authored
commit ad83dbd9 upstream. The "adl_pci7x3x" driver replaced the "adl_pci7230" and "adl_pci7432" drivers in commits 8f567c37 ("staging: comedi: new adl_pci7x3x driver") and 657f77d1 ("staging: comedi: remove adl_pci7230 and adl_pci7432 drivers"). Although the new driver code agrees with the user manuals for the respective boards, digital outputs stopped working on the PCI-7230. This has 16 digital output channels and the previous adl_pci7230 driver shifted the 16 bit output state left by 16 bits before writing to the hardware register. The new adl_pci7x3x driver doesn't do that. Fix it in `adl_pci7x3x_do_insn_bits()` by checking for the special case of the subdevice having only 16 channels and duplicating the 16 bit output state into both halves of the 32-bit register. That should work both for what the board actually does and for what the user manual says it should do. Fixes: 8f567c37 ("staging: comedi: new adl_pci7x3x driver") Signed-off-by:
-
Mateusz Kulikowski authored
commit 435009bb upstream. This patch fixes issue generated by commit ca93dcba ("staging: rtl8192e: Remove assert() macro") One negation was missed in conversion, therefore asserted message was always printed. For 1MB file downloaded via http, ~500 messages were generated. Signed-off-by:
Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Signed-off-by:
-
Jan H. Schönherr authored
commit dd9d3843 upstream. There is a race condition in SMP bootup code, which may result in WARNING: CPU: 0 PID: 1 at kernel/workqueue.c:4418 workqueue_cpu_up_callback() or kernel BUG at kernel/smpboot.c:135! It can be triggered with a bit of luck in Linux guests running on busy hosts. CPU0 CPUn ==== ==== _cpu_up() __cpu_up() start_secondary() set_cpu_online() cpumask_set_cpu(cpu, to_cpumask(cpu_online_bits)); cpu_notify(CPU_ONLINE) <do stuff, see below> cpumask_set_cpu(cpu, to_cpumask(cpu_active_bits)); During the various CPU_ONLINE callbacks CPUn is online but not active. Several things can go wrong at that point, depending on the scheduling of tasks on CPU0. Variant 1: cpu_notify(CPU_ONLINE) workqueue_cpu_up_callback() rebind_workers() set_cpus_allowed_ptr() This call fails because it requires an active CPU; rebind_workers() ends with a warning: WARNING: CPU: 0 PID: 1 at kernel/workqueue.c:4418 workqueue_cpu_up_callback() Variant 2: cpu_notify(CPU_ONLINE) smpboot_thread_call() smpboot_unpark_threads() .. __kthread_unpark() __kthread_bind() wake_up_state() .. select_task_rq() select_fallback_rq() The ->wake_cpu of the unparked thread is not allowed, making a call to select_fallback_rq() necessary. Then, select_fallback_rq() cannot find an allowed, active CPU and promptly resets the allowed CPUs, so that the task in question ends up on CPU0. When those unparked tasks are eventually executed, they run immediately into a BUG: kernel BUG at kernel/smpboot.c:135! Just changing the order in which the online/active bits are set (and adding some memory barriers), would solve the two issues above. However, it would change the order of operations back to the one before commit 6acbfb96 ("sched: Fix hotplug vs. set_cpus_allowed_ptr()"), thus, reintroducing that particular problem. Going further back into history, we have at least the following commits touching this topic: - commit 2baab4e9 ("sched: Fix select_fallback_rq() vs cpu_active/cpu_online") - commit 5fbd036b ("sched: Cleanup cpu_active madness") Together, these give us the following non-working solutions: - secondary CPU sets active before online, because active is assumed to be a subset of online; - secondary CPU sets online before active, because the primary CPU assumes that an online CPU is also active; - secondary CPU sets online and waits for primary CPU to set active, because it might deadlock. Commit 875ebe94 ("powerpc/smp: Wait until secondaries are active & online") introduces an arch-specific solution to this arch-independent problem. Now, go for a more general solution without explicit waiting and simply set active twice: once on the secondary CPU after online was set and once on the primary CPU after online was seen. set_cpus_allowed_ptr()") Signed-off-by:
Jan H. Schönherr <jschoenh@amazon.de> Acked-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Anton Blanchard <anton@samba.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Joerg Roedel <jroedel@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Wilson <msw@amazon.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 6acbfb96 ("sched: Fix hotplug vs. set_cpus_allowed_ptr()") Link: http://lkml.kernel.org/r/1439408156-18840-1-git-send-email-jschoenh@amazon.deSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Hartmut Knaack authored
commit 001fceb9 upstream. To iterate through the available frequencies of mma8452_hp_filter_cutoff[], the array size of a row of that table needs to be provided to _get_int_plus_micros_index(). Fixes: 1e79841a ("iio: mma8452: Add highpass filter configuration.") Signed-off-by:
Hartmut Knaack <knaack.h@gmx.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit 7abad106 upstream. The different devices support by the adis16480 driver have slightly different scales for the gyroscope and accelerometer channels. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Lars-Peter Clausen authored
commit c689a923 upstream. Add inverse unit conversion macro to convert from standard IIO units to units that might be used by some devices. Those are useful in combination with scale factors that are specified as IIO_VAL_FRACTIONAL. Typically the denominator for those specifications will contain the maximum raw value the sensor will generate and the numerator the value it maps to in a specific unit. Sometimes datasheets specify those in different units than the standard IIO units (e.g. degree/s instead of rad/s) and so we need to do a unit conversion. From a mathematical point of view it does not make a difference whether we apply the unit conversion to the numerator or the inverse unit conversion to the denominator since (x / y) / z = x / (y * z). But as the denominator is typically a larger value and we are rounding both the numerator and denominator to integer values using the later method gives us a better precision (E.g. the relative error is smaller if we round 8000.3 to 8000 rather than rounding 8.3 to 8). This is where in inverse unit conversion macros will be used. Marked for stable as used by some upcoming fixes. Signed-off-by:
-
Lars-Peter Clausen authored
commit 81665372 upstream. Use the correct scale for the adis16448 gyroscope output. Signed-off-by:
-
Cristina Opriceana authored
commit 1bdc0293 upstream. Change return value to 0 if no device is bound since unsigned int cannot support negative error codes. Fixes: f18e7a06 ("iio: Return -ENODEV for file operations if the device has been unregistered") Signed-off-by:
Cristina Opriceana <cristina.opriceana@gmail.com> Signed-off-by:
-
Cristina Opriceana authored
commit 41d903c0 upstream. Negative return values are not supported by iio_event_poll since its return type is unsigned int. Fixes: f18e7a06 ("iio: Return -ENODEV for file operations if the device has been unregistered") Signed-off-by:
-
Markus Pargmann authored
commit 06d2f6ca upstream. This patch adds selects for IIO_BUFFER and IIO_TRIGGERED_BUFFER. Without IIO_BUFFER, the driver does not compile. Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Reviewed-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Martin Schwidefsky authored
commit 89b1145e upstream. The novx parameter disables the vector facility but the HWCAP_S390_VXRS bit in the ELf hardware capabilies is always set if the machine has the vector facility. If the user space program uses the "vx" string in the features field of /proc/cpuinfo to utilize vector instruction it will crash if the novx kernel paramter is set. Convert setup_hwcaps to an arch_initcall and use MACHINE_HAS_VX to decide if the HWCAPS_S390_VXRS bit needs to be set. Reported-by:
Ulrich Weigand <uweigand@de.ibm.com> Reviewed-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Takashi Iwai authored
commit 982b0b2d upstream. Fix a wrong logical AND (&&) used for the range check of CSR MMIO. Spotted nicely by gcc -Wlogical-op flag: drivers/gpu/drm/i915/intel_csr.c: In function ‘finish_csr_load’: drivers/gpu/drm/i915/intel_csr.c:353:41: warning: logical ‘and’ of mutually exclusive tests is always false [-Wlogical-op] Fixes: eb805623 ('drm/i915/skl: Add support to load SKL CSR firmware.') Signed-off-by:
Takashi Iwai <tiwai@suse.de> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
Animesh Manna <animesh.manna@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Chris Wilson authored
commit acd29f7b upstream. In I915_READ64_2x32 we attempt to read a 64bit register using 2 32bit reads. Due to the nature of the registers we try to read in this manner, they may increment between the two instruction (e.g. a timestamp counter). To keep the result accurate, we repeat the read if we detect an overflow (i.e. the upper value varies). However, some hardware is just plain flaky and may endless loop as the the upper 32bits are not stable. Just give up after a couple of tries and report whatever we read last. v2: Use the most recent values when erring out on an unstable register. Reported-by: russianneuromancer@ya.ru Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91906Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by:
-
Chris Wilson authored
commit 51bc1404 upstream. There have been many hard to track down bugs whereby userspace forgot to flag a write buffer and then cause graphics corruption or a hung GPU when that buffer was later purged under memory pressure (as the buffer appeared clean, its pages would have been evicted rather than preserved and any changes more recent than in the backing storage would be lost). In retrospect this is a rare optimisation against memory pressure, already the slow path. If we always mark the buffer as dirty when accessed by the GPU, anything not used can still be evicted cheaply (ideal behaviour for mark-and-sweep eviction) but we do not run the risk of corruption. For correct read serialisation, userspace still has to notify when the GPU writes to an object. However, there are certain situations under which userspace may wish to tell white lies to the kernel... Signed-off-by:
-
Gaurav K Singh authored
commit 82425785 upstream. Just like single link MIPI panels, similarly for dual link panels, pipe to be configured is based on the DVO port from VBT Block 2. In hardware, Port A is mapped with Pipe A and Port C is mapped with Pipe B. This issue got introduced in - commit 7e9804fd Author: Jani Nikula <jani.nikula@intel.com> Date: Fri Jan 16 14:27:23 2015 +0200 drm/i915/dsi: add drm mipi dsi host support Signed-off-by:
Gaurav K Singh <gaurav.k.singh@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jonathon Jongsma authored
commit bd3e1c7c upstream. Due to some recent changes in drm_helper_probe_single_connector_modes_merge_bits(), old custom modes were not being pruned properly. In current kernels, drm_mode_validate_basic() is called to sanity-check each mode in the list. If the sanity-check passes, the mode's status gets set to to MODE_OK. In older kernels this check was not done, so old custom modes would still have a status of MODE_UNVERIFIED at this point, and would therefore be pruned later in the function. As a result of this new behavior, the list of modes for a device always includes every custom mode ever configured for the device, with the largest one listed first. Since desktop environments usually choose the first preferred mode when a hotplug event is emitted, this had the result of making it very difficult for the user to reduce the size of the display. The qxl driver did implement the mode_valid connector function, but it was empty. In order to restore the old behavior where old custom modes are pruned, we implement a proper mode_valid function for the qxl driver. This function now checks each mode against the last configured custom mode and the list of standard modes. If the mode doesn't match any of these, its status is set to MODE_BAD so that it will be pruned as expected. Signed-off-by:
Jonathon Jongsma <jjongsma@redhat.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Lukas Wunner authored
commit 69f92f67 upstream. Commit 92122789 ("drm/i915: preserve SSC if previously set v3") added code to intel_modeset_gem_init to override the SSC status read from VBT with the SSC status set by BIOS. However, intel_modeset_gem_init is invoked *after* intel_modeset_init, which calls intel_setup_outputs, which *modifies* SSC status by way of intel_init_pch_refclk. So unlike advertised, intel_modeset_gem_init doesn't preserve the SSC status set by BIOS but whatever intel_init_pch_refclk decided on. This is a problem on dual gpu laptops such as the MacBook Pro which require either a handler to switch DDC lines, or the discrete gpu to proxy DDC/AUX communication: Both the handler and the discrete gpu may initialize after the i915 driver, and consequently, an LVDS connector may initially seem disconnected and the SSC therefore is disabled by intel_init_pch_refclk, but on reprobe the connector may turn out to be connected and the SSC must then be enabled. Due to 92122789 however, the SSC is not enabled on reprobe since it is assumed BIOS disabled it while in fact it was disabled by intel_init_pch_refclk. Also, because the SSC status is preserved so late, the preserved value only ever gets used on resume but not on panel initialization: intel_modeset_init calls intel_init_display which indirectly calls intel_panel_use_ssc via multiple subroutines, *before* the BIOS value overrides the VBT value in intel_modeset_gem_init (intel_panel_use_ssc is the sole user of dev_priv->vbt.lvds_use_ssc). Fix this by moving the code introduced by 92122789 from intel_modeset_gem_init to intel_modeset_init before the invocation of intel_setup_outputs and intel_init_display. Add a DRM_DEBUG_KMS as suggested way back by Jani: http://lists.freedesktop.org/archives/intel-gfx/2014-June/046666.html Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115Tested-by:
Paul Hordiienko <pvt.gord@gmail.com> [MBP 6,2 2010 intel ILK + nvidia GT216 pre-retina] Tested-by:
William Brown <william@blackhats.net.au> [MBP 8,2 2011 intel SNB + amd turks pre-retina] Tested-by:
Lukas Wunner <lukas@wunner.de> [MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina] Tested-by:
Bruno Bierbaumer <bruno@bierbaumer.net> [MBP 11,3 2013 intel HSW + nvidia GK107 retina -- work in progress] Fixes: 92122789 ("drm/i915: preserve SSC if previously set v3") Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Alex Deucher authored
commit be9fd2e9 upstream. Using the wrong watermwark value for the secondary watermark. Copy paste typo. Noticed by Mykola. Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 99a09238 upstream. Using the wrong watermwark value for the secondary watermark. Copy paste typo. Noticed by Mykola. Reviewed-by:
-
Alex Deucher authored
commit 52293c67 upstream. Use pci_alloc_consistent rather than kzalloc since we need 256 byte aligned memory for the ring buffer. v2: fix copy paste typo in free function noticed by Jammy. bug: https://bugs.freedesktop.org/show_bug.cgi?id=91749Reviewed-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Jammy Zhou <Jammy.Zhou@amd.com> Signed-off-by:
-
Alex Deucher authored
commit a887adad upstream. This is a port of: DRM - radeon: Don't link train DisplayPort on HPD until we get the dpcd to amdgpu. Signed-off-by:
-
Jammy Zhou authored
commit 21df89a5 upstream. In function 'amdgpu_uvd_cs_pass2': warning: 'min_ctx_size' may be used uninitialized in this function buf_sizes[0x4] = min_ctx_size; ^ note: 'min_ctx_size' was declared here unsigned image_size, tmp, min_dpb_size, num_dpb_buffer, min_ctx_size; ^ Signed-off-by:
-
Alex Deucher authored
commit 86b7709d upstream. Support for output_csc is only available on DCE5 and newer so don't mess with the HDMI quantization_range on pre-DCE5 asics. bug: https://bugs.freedesktop.org/show_bug.cgi?id=83226Signed-off-by:
-
Alex Deucher authored
commit 7040c399 upstream. AUX addresses are 20 bits long. Send out the entire address instead of just the low 16 bits. Port of: drm/radeon/atom: Send out the full AUX address to radeon non-atom aux path Reviewed-by:
-
Alex Deucher authored
commit e39daf2c upstream. AUX addresses are 20 bits long. Send out the entire address instead of just the low 16 bits. Port of: drm/radeon/atom: Send out the full AUX address to amdgpu Reviewed-by:
-
Ville Syrjälä authored
commit 3f8340cc upstream. AUX addresses are 20 bits long. Send out the entire address instead of just the low 16 bits. Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Signed-off-by:
-
Ville Syrjälä authored
commit d14e7b6d upstream. We are no longer checkling the DP link status on long hpd. We used to do that from the .hot_plug() handler, but it was removed when MST got introduced. If there's no userspace we now fail to retrain the link if the sink power is toggled (or cable yanked and replugged), meaning the user is left staring at a blank screen. With the retraining put back that should be fixed. Also remove the leftover comment that referred to the old retraining from .hot_plug(). Fixes a regression introduced in: commit 0e32b39c Author: Dave Airlie <airlied@redhat.com> Date: Fri May 2 14:02:48 2014 +1000 drm/i915: add DP 1.2 MST support (v0.7) Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89453Tested-by:
Palmer Dabbelt <palmer@dabbelt.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91407 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89461 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89594 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85641 Cc: Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Imre Deak authored
commit 54875571 upstream. commit da2bc1b9 Author: Imre Deak <imre.deak@intel.com> Date: Thu Oct 23 19:23:26 2014 +0300 drm/i915: add poweroff_late handler introduced a regression on old platforms during hibernation. A workaround was added in commit ab3be73f Author: Imre Deak <imre.deak@intel.com> Date: Mon Mar 2 13:04:41 2015 +0200 drm/i915: gen4: work around hang during hibernation using an explicit blacklist for the GENs/BIOS vendors where the issue was reported. Later there we had reports of the same failure on platforms not on this list. To my best knowledge the correct thing to do is still to put the device to PCI D3 state during hibernation, see [1] and [2] for the reasons. This also aligns with our future plans to unify more the runtime and system suspend/resume paths. Since an exact blacklist seems to be impractical (multiple GENs and BIOS vendors are affected) apply the workaround on everything pre GEN6. [1] http://lists.freedesktop.org/archives/intel-gfx/2015-February/060710.html [2] https://lkml.org/lkml/2015/6/22/274 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95061Reported-by:
Ilya Tumaykin <itumaykin@gmail.com> Reported-by:
Dirk Griesbach <spamthis@freenet.de> Reported-by:
Pavel Machek <pavel@ucw.cz> Reported-by:
Mikko Rapeli <mikko.rapeli@iki.fi> Tested-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
-
Stephen Chandler Paul authored
commit 924f92bf upstream. Most of the time this isn't an issue since hotplugging an adaptor will trigger a crtc mode change which in turn, causes the driver to probe every DisplayPort for a dpcd. However, in cases where hotplugging doesn't cause a mode change (specifically when one unplugs a monitor from a DisplayPort connector, then plugs that same monitor back in seconds later on the same port without any other monitors connected), we never probe for the dpcd before starting the initial link training. What happens from there looks like this: - GPU has only one monitor connected. It's connected via DisplayPort, and does not go through an adaptor of any sort. - User unplugs DisplayPort connector from GPU. - Change in HPD is detected by the driver, we probe every DisplayPort for a possible connection. - Probe the port the user originally had the monitor connected on for it's dpcd. This fails, and we clear the first (and only the first) byte of the dpcd to indicate we no longer have a dpcd for this port. - User plugs the previously disconnected monitor back into the same DisplayPort. - radeon_connector_hotplug() is called before everyone else, and tries to handle the link training. Since only the first byte of the dpcd is zeroed, the driver is able to complete link training but does so against the wrong dpcd, causing it to initialize the link with the wrong settings. - Display stays blank (usually), dpcd is probed after the initial link training, and the driver prints no obvious messages to the log. In theory, since only one byte of the dpcd is chopped off (specifically, the byte that contains the revision information for DisplayPort), it's not entirely impossible that this bug may not show on certain monitors. For instance, the only reason this bug was visible on my ASUS PB238 monitor was due to the fact that this monitor using the enhanced framing symbol sequence, the flag for which is ignored if the radeon driver thinks that the DisplayPort version is below 1.1. Signed-off-by:
Stephen Chandler Paul <cpaul@redhat.com> Reviewed-by:
Jerome Glisse <jglisse@redhat.com> Signed-off-by:
-
- 30 Aug, 2015 1 commit
-
-
Linus Torvalds authored
-
- 29 Aug, 2015 1 commit
-
-
Javi Merino authored
Commit cf736ea6 ("thermal: power_allocator: do not use devm* interfaces") forgot to change a devm_kcalloc() to just kcalloc(), but it's corresponding devm_kfree() was changed to kfree(). Allocate with kcalloc() to match the kfree(). Fixes: cf736ea6 ("thermal: power_allocator: do not use devm* interfaces") Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: Zhang Rui <rui.zhang@intel.com> Signed-off-by:
Javi Merino <javi.merino@arm.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 28 Aug, 2015 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libataLinus Torvalds authored
Pull libata fixlet from Tejun Heo: "Simple blacklist entry addition" * 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: Add factory recertified Crucial M500s to blacklist
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds authored
Pull sound fixes from Takashi Iwai: "Here are stable fixes that have been gathered since rc8: fixes for HD-audio widget power control regressions since 4.1, a NULL fix for HD-audio HDMI, a noise fix for Conexant codecs and a quirk addition for USB-Audio DSD" * tag 'sound-fix-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda - Fix path power activation ALSA: hda - Check all inputs for is_active_nid_for_any() ALSA: hda: fix possible NULL dereference ALSA: hda - Shutdown CX20722 on reboot/free to avoid spurious noises ALSA: usb: Add native DSD support for Gustard DAC-X20U
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: "Fix MSI/MSI-X on pseries from Guilherme" * tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code
-
