- 19 Jun, 2015 39 commits
-
-
Martin KaFai Lau authored
commit 3b471175 upstream. ipv6_cow_metrics() currently assumes only DST_HOST routes require dynamic metrics allocation from inetpeer. The assumption breaks when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric. Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set() is called after the route is created. This patch creates the metrics array (by calling dst_cow_metrics_generic) in ipv6_cow_metrics(). Test: radvd.conf: interface qemubr0 { AdvLinkMTU 1300; AdvCurHopLimit 30; prefix fd00:face:face:face::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; }; Before: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec fe80::/64 dev eth0 proto kernel metric 256 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec After: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec mtu 1300 fe80::/64 dev eth0 proto kernel metric 256 mtu 1300 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec mtu 1300 hoplimit 30 Fixes: 8e2ec639 (ipv6: don't use inetpeer to store metrics for routes.) Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Zefan Li <lizefan@huawei.com>
-
Darrick J. Wong authored
commit 37527b86 upstream. I created a dm-raid1 device backed by a device that supports DISCARD and another device that does NOT support DISCARD with the following dm configuration: # echo '0 2048 mirror core 1 512 2 /dev/sda 0 /dev/sdb 0' | dmsetup create moo # lsblk -D NAME DISC-ALN DISC-GRAN DISC-MAX DISC-ZERO sda 0 4K 1G 0 `-moo (dm-0) 0 4K 1G 0 sdb 0 0B 0B 0 `-moo (dm-0) 0 4K 1G 0 Notice that the mirror device /dev/mapper/moo advertises DISCARD support even though one of the mirror halves doesn't. If I issue a DISCARD request (via fstrim, mount -o discard, or ioctl BLKDISCARD) through the mirror, kmirrord gets stuck in an infinite loop in do_region() when it tries to issue a DISCARD request to sdb. The problem is that when we call do_region() against sdb, num_sectors is set to zero because q->limits.max_discard_sectors is zero. Therefore, "remaining" never decreases and the loop never terminates. To fix this: before entering the loop, check for the combination of REQ_DISCARD and no discard and return -EOPNOTSUPP to avoid hanging up the mirror device. This bug was found by the unfortunate coincidence of pvmove and a discard operation in the RHEL 6.5 kernel; upstream is also affected. Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Acked-by:
"Martin K. Petersen" <martin.petersen@oracle.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
commit f2ed51ac upstream. It may be possible that a device claims discard support but it rejects discards with -EOPNOTSUPP. It happens when using loopback on ext2/ext3 filesystem driven by the ext4 driver. It may also happen if the underlying devices are moved from one disk on another. If discard error happens, we reject the bio with -EOPNOTSUPP, but we do not degrade the array. This patch fixes failed test shell/lvconvert-repair-transient.sh in the lvm2 testsuite if the testsuite is extracted on an ext2 or ext3 filesystem and it is being driven by the ext4 driver. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Chen Jie authored
commit 164c2406 upstream. sm->offset maybe wrong but magic maybe right, the offset do not have CRC. Badness at c00c7580 [verbose debug info unavailable] NIP: c00c7580 LR: c00c718c CTR: 00000014 REGS: df07bb40 TRAP: 0700 Not tainted (2.6.34.13-WR4.3.0.0_standard) MSR: 00029000 <EE,ME,CE> CR: 22084f84 XER: 00000000 TASK = df84d6e0[908] 'mount' THREAD: df07a000 GPR00: 00000001 df07bbf0 df84d6e0 00000000 00000001 00000000 df07bb58 00000041 GPR08: 00000041 c0638860 00000000 00000010 22084f88 100636c8 df814ff8 00000000 GPR16: df84d6e0 dfa558cc c05adb90 00000048 c0452d30 00000000 000240d0 000040d0 GPR24: 00000014 c05ae734 c05be2e0 00000000 00000001 00000000 00000000 c05ae730 NIP [c00c7580] __alloc_pages_nodemask+0x4d0/0x638 LR [c00c718c] __alloc_pages_nodemask+0xdc/0x638 Call Trace: [df07bbf0] [c00c718c] __alloc_pages_nodemask+0xdc/0x638 (unreliable) [df07bc90] [c00c7708] __get_free_pages+0x20/0x48 [df07bca0] [c00f4a40] __kmalloc+0x15c/0x1ec [df07bcd0] [c01fc880] jffs2_scan_medium+0xa58/0x14d0 [df07bd70] [c01ff38c] jffs2_do_mount_fs+0x1f4/0x6b4 [df07bdb0] [c020144c] jffs2_do_fill_super+0xa8/0x260 [df07bdd0] [c020230c] jffs2_fill_super+0x104/0x184 [df07be00] [c0335814] get_sb_mtd_aux+0x9c/0xec [df07be20] [c033596c] get_sb_mtd+0x84/0x1e8 [df07be60] [c0201ed0] jffs2_get_sb+0x1c/0x2c [df07be70] [c0103898] vfs_kern_mount+0x78/0x1e8 [df07bea0] [c0103a58] do_kern_mount+0x40/0x100 [df07bec0] [c011fe90] do_mount+0x240/0x890 [df07bf10] [c0120570] sys_mount+0x90/0xd8 [df07bf40] [c00110d8] ret_from_syscall+0x0/0x4 === Exception: c01 at 0xff61a34 LR = 0x100135f0 Instruction dump: 38800005 38600000 48010f41 4bfffe1c 4bfc2d15 4bfffe8c 72e90200 4082fc28 3d20c064 39298860 8809000d 68000001 <0f000000> 2f800000 419efc0c 38000001 mount: mounting /dev/mtdblock3 on /common failed: Input/output error Signed-off-by:
Chen Jie <chenjie6@huawei.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Adrian Knoth authored
commit f0153c3d upstream. RME RayDAT and AIO use a fixed buffer size of 16384 samples. With period sizes of 32-4096, this translates to 4-512 periods. The older RME cards have a variable buffer size but require exactly two periods. This patch enforces nperiods=2 on those cards. Signed-off-by:
Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Alex Deucher authored
commit 66c2b84b upstream. Don't restrict it to just eDP panels. Some LVDS bridge chips require this. Fixes blank panels on resume on certain laptops. Noticed by mrnuke on IRC. bug: https://bugs.freedesktop.org/show_bug.cgi?id=42960Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Grazvydas Ignotas authored
commit 9cb12d7b upstream. For whatever reason, generic_access_phys() only remaps one page, but actually allows to access arbitrary size. It's quite easy to trigger large reads, like printing out large structure with gdb, which leads to a crash. Fix it by remapping correct size. Fixes: 28b2ee20 ("access_process_vm device memory infrastructure") Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 3fd7b60f upstream. This patch drops legacy active_ts_list usage within iscsi_target_tq.c code. It was originally used to track the active thread sets during iscsi-target shutdown, and is no longer used by modern upstream code. Two people have reported list corruption using traditional iscsi-target and iser-target with the following backtrace, that appears to be related to iscsi_thread_set->ts_list being used across both active_ts_list and inactive_ts_list. [ 60.782534] ------------[ cut here ]------------ [ 60.782543] WARNING: CPU: 0 PID: 9430 at lib/list_debug.c:53 __list_del_entry+0x63/0xd0() [ 60.782545] list_del corruption, ffff88045b00d180->next is LIST_POISON1 (dead000000100100) [ 60.782546] Modules linked in: ib_srpt tcm_qla2xxx qla2xxx tcm_loop tcm_fc libfc scsi_transport_fc scsi_tgt ib_isert rdma_cm iw_cm ib_addr iscsi_target_mod target_core_pscsi target_core_file target_core_iblock target_core_mod configfs ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 ipt_REJECT xt_CHECKSUM iptable_mangle iptable_filter ip_tables bridge stp llc autofs4 sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ib_ipoib ib_cm ib_uverbs ib_umad mlx4_en mlx4_ib ib_sa ib_mad ib_core mlx4_core dm_mirror dm_region_hash dm_log dm_mod vhost_net macvtap macvlan vhost tun kvm_intel kvm uinput iTCO_wdt iTCO_vendor_support microcode serio_raw pcspkr sb_edac edac_core sg i2c_i801 lpc_ich mfd_core mtip32xx igb i2c_algo_bit i2c_core ptp pps_core ioatdma dca wmi ext3(F) jbd(F) mbcache(F) sd_mod(F) crc_t10dif(F) crct10dif_common(F) ahci(F) libahci(F) isci(F) libsas(F) scsi_transport_sas(F) [last unloaded: speedstep_lib] [ 60.782597] CPU: 0 PID: 9430 Comm: iscsi_ttx Tainted: GF 3.12.19+ #2 [ 60.782598] Hardware name: Supermicro X9DRX+-F/X9DRX+-F, BIOS 3.00 07/09/2013 [ 60.782599] 0000000000000035 ffff88044de31d08 ffffffff81553ae7 0000000000000035 [ 60.782602] ffff88044de31d58 ffff88044de31d48 ffffffff8104d1cc 0000000000000002 [ 60.782605] ffff88045b00d180 ffff88045b00d0c0 ffff88045b00d0c0 ffff88044de31e58 [ 60.782607] Call Trace: [ 60.782611] [<ffffffff81553ae7>] dump_stack+0x49/0x62 [ 60.782615] [<ffffffff8104d1cc>] warn_slowpath_common+0x8c/0xc0 [ 60.782618] [<ffffffff8104d2b6>] warn_slowpath_fmt+0x46/0x50 [ 60.782620] [<ffffffff81280933>] __list_del_entry+0x63/0xd0 [ 60.782622] [<ffffffff812809b1>] list_del+0x11/0x40 [ 60.782630] [<ffffffffa06e7cf9>] iscsi_del_ts_from_active_list+0x29/0x50 [iscsi_target_mod] [ 60.782635] [<ffffffffa06e87b1>] iscsi_tx_thread_pre_handler+0xa1/0x180 [iscsi_target_mod] [ 60.782642] [<ffffffffa06fb9ae>] iscsi_target_tx_thread+0x4e/0x220 [iscsi_target_mod] [ 60.782647] [<ffffffffa06fb960>] ? iscsit_handle_snack+0x190/0x190 [iscsi_target_mod] [ 60.782652] [<ffffffffa06fb960>] ? iscsit_handle_snack+0x190/0x190 [iscsi_target_mod] [ 60.782655] [<ffffffff8106f99e>] kthread+0xce/0xe0 [ 60.782657] [<ffffffff8106f8d0>] ? kthread_freezable_should_stop+0x70/0x70 [ 60.782660] [<ffffffff8156026c>] ret_from_fork+0x7c/0xb0 [ 60.782662] [<ffffffff8106f8d0>] ? kthread_freezable_should_stop+0x70/0x70 [ 60.782663] ---[ end trace 9662f4a661d33965 ]--- Since this code is no longer used, go ahead and drop the problematic usage all-together. Reported-by:
Gavin Guo <gavin.guo@canonical.com> Reported-by:
Moussa Ba <moussaba@micron.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Roman Gushchin authored
commit 8138a67a upstream. I noticed that "allowed" can easily overflow by falling below 0, because (total_vm / 32) can be larger than "allowed". The problem occurs in OVERCOMMIT_NONE mode. In this case, a huge allocation can success and overcommit the system (despite OVERCOMMIT_NONE mode). All subsequent allocations will fall (system-wide), so system become unusable. The problem was masked out by commit c9b1d098 ("mm: limit growth of 3% hardcoded other user reserve"), but it's easy to reproduce it on older kernels: 1) set overcommit_memory sysctl to 2 2) mmap() large file multiple times (with VM_SHARED flag) 3) try to malloc() large amount of memory It also can be reproduced on newer kernels, but miss-configured sysctl_user_reserve_kbytes is required. Fix this issue by switching to signed arithmetic here. Signed-off-by:
Roman Gushchin <klamm@yandex-team.ru> Cc: Andrew Shewmaker <agshew@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
Roman Gushchin authored
commit 5703b087 upstream. I noticed, that "allowed" can easily overflow by falling below 0, because (total_vm / 32) can be larger than "allowed". The problem occurs in OVERCOMMIT_NONE mode. In this case, a huge allocation can success and overcommit the system (despite OVERCOMMIT_NONE mode). All subsequent allocations will fall (system-wide), so system become unusable. The problem was masked out by commit c9b1d098 ("mm: limit growth of 3% hardcoded other user reserve"), but it's easy to reproduce it on older kernels: 1) set overcommit_memory sysctl to 2 2) mmap() large file multiple times (with VM_SHARED flag) 3) try to malloc() large amount of memory It also can be reproduced on newer kernels, but miss-configured sysctl_user_reserve_kbytes is required. Fix this issue by switching to signed arithmetic here. [akpm@linux-foundation.org: use min_t] Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Naoya Horiguchi authored
commit 9fbc1f63 upstream. If __unmap_hugepage_range() tries to unmap the address range over which hugepage migration is on the way, we get the wrong page because pte_page() doesn't work for migration entries. This patch simply clears the pte for migration entries as we do for hwpoison entries. Fixes: 290408d4 ("hugetlb: hugepage migration core") Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Steve Capper <steve.capper@linaro.org> Signed-off-by:
-
Naoya Horiguchi authored
commit a8bda28d upstream. There is a race condition between hugepage migration and change_protection(), where hugetlb_change_protection() doesn't care about migration entries and wrongly overwrites them. That causes unexpected results like kernel crash. HWPoison entries also can cause the same problem. This patch adds is_hugetlb_entry_(migration|hwpoisoned) check in this function to do proper actions. Fixes: 290408d4 ("hugetlb: hugepage migration core") Signed-off-by:
-
Naoya Horiguchi authored
commit 0f792cf9 upstream. When running the test which causes the race as shown in the previous patch, we can hit the BUG "get_page() on refcount 0 page" in hugetlb_fault(). This race happens when pte turns into migration entry just after the first check of is_hugetlb_entry_migration() in hugetlb_fault() passed with false. To fix this, we need to check pte_present() again after huge_ptep_get(). This patch also reorders taking ptl and doing pte_page(), because pte_page() should be done in ptl. Due to this reordering, we need use trylock_page() in page != pagecache_page case to respect locking order. Fixes: 66aebce7 ("hugetlb: fix race condition in hugetlb_fault()") Signed-off-by:
-
Mikulas Patocka authored
commit d4d4eda2 upstream. On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the speedstep-smi driver sometimes loads and sometimes doesn't load with "change to state X failed" message. The hardware sometimes refuses to change frequency and in this case, we need to retry later. I found out that we need to enable interrupts while waiting. When we enable interrupts, the hardware blockage that prevents frequency transition resolves and the transition is possible. With disabled interrupts, the blockage doesn't resolve (no matter how long do we wait). The exact reasons for this hardware behavior are unknown. This patch enables interrupts in the function speedstep_set_state that can be called with disabled interrupts. However, this function is called with disabled interrupts only from speedstep_get_freqs, so it shouldn't cause any problem. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Trond Myklebust authored
commit d8ba1f97 upstream. If the call to decode_rc_list() fails due to a memory allocation error, then we need to truncate the array size to ensure that we only call kfree() on those pointer that were allocated. Reported-by:
David Ramos <daramos@stanford.edu> Fixes: 4aece6a1 ("nfs41: cb_sequence xdr implementation") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Jan Kara authored
commit 6ee8e25f upstream. Commit e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify") broke handling of renames in audit. Audit code wants to update inode number of an inode corresponding to watched name in a directory. When something gets renamed into a directory to a watched name, inotify previously passed moved inode to audit code however new fsnotify code passes directory inode where the change happened. That confuses audit and it starts watching parent directory instead of a file in a directory. This can be observed for example by doing: cd /tmp touch foo bar auditctl -w /tmp/foo touch foo mv bar foo touch foo In audit log we see events like: type=CONFIG_CHANGE msg=audit(1423563584.155:90): auid=1000 ses=2 op="updated rules" path="/tmp/foo" key=(null) list=4 res=1 ... type=PATH msg=audit(1423563584.155:91): item=2 name="bar" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE type=PATH msg=audit(1423563584.155:91): item=3 name="foo" inode=1046842 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE type=PATH msg=audit(1423563584.155:91): item=4 name="foo" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=CREATE ... and that's it - we see event for the first touch after creating the audit rule, we see events for rename but we don't see any event for the last touch. However we start seeing events for unrelated stuff happening in /tmp. Fix the problem by passing moved inode as data in the FS_MOVED_FROM and FS_MOVED_TO events instead of the directory where the change happens. This doesn't introduce any new problems because noone besides audit_watch.c cares about the passed value: fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events. fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all. fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH. kernel/audit_tree.c doesn't care about passed 'data' at all. kernel/audit_watch.c expects moved inode as 'data'. Fixes: e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify") Signed-off-by:
Jan Kara <jack@suse.cz> Cc: Paul Moore <paul@paul-moore.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by:
-
Dan Carpenter authored
commit e4940626 upstream. The problem here is that we check: if (dev >= SNDRV_CARDS) Then we increment "dev". if (!joystick_port[dev++]) Then we use it as an offset into a array with SNDRV_CARDS elements. if (!request_region(joystick_port[dev], 8, "Riptide gameport")) { This has 3 effects: 1) If you use the module option to specify the joystick port then it has to be shifted one space over. 2) The wrong error message will be printed on failure if you have over 32 cards. 3) Static checkers will correctly complain that are off by one. Fixes: db1005ec ('ALSA: riptide - Fix joystick resource handling') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Daniel Borkmann authored
commit 364d5716 upstream. ifla_vf_policy[] is wrong in advertising its individual member types as NLA_BINARY since .type = NLA_BINARY in combination with .len declares the len member as *max* attribute length [0, len]. The issue is that when do_setvfinfo() is being called to set up a VF through ndo handler, we could set corrupted data if the attribute length is less than the size of the related structure itself. The intent is exactly the opposite, namely to make sure to pass at least data of minimum size of len. Fixes: ebc08a6f ("rtnetlink: Add VF config code to rtnetlink") Cc: Mitch Williams <mitch.a.williams@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Sergey Ryazanov authored
commit 8bfae4f9 upstream. Sometimes while CPU have some load and ath5k doing the wireless interface reset the whole WiSoC completely freezes. Set of tests shows that using atomic delay function while we wait interface reset helps to avoid such freezes. The easiest way to reproduce this issue: create a station interface, start continous scan with wpa_supplicant and load CPU by something. Or just create multiple station interfaces and put them all in continous scan. This patch partially reverts the commit 1846ac3d ("ath5k: Use usleep_range where possible"), which replaces initial udelay() by usleep_range(). I do not know actual source of this issue, but all looks like that HW freeze is caused by transaction on internal SoC bus, while wireless block is in reset state. Also I should note that I do not know how many chips are affected, but I did not see this issue with chips, other than AR5312. CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Fixes: 1846ac3d ("ath5k: Use usleep_range where possible") Reported-by:
Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by:
Eric Bree <ebree@nltinc.com> Signed-off-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Peter Hurley authored
commit 37480a05 upstream. Commit 26df6d13 ("tty: Add EXTPROC support for LINEMODE") allows a process which has opened a pty master to send _any_ signal to the process group of the pty slave. Although potentially exploitable by a malicious program running a setuid program on a pty slave, it's unknown if this exploit currently exists. Limit to signals actually used. Cc: Theodore Ts'o <tytso@mit.edu> Cc: Howard Chu <hyc@symas.com> Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Nicolas Pitre authored
commit 19e3ae6b upstream. The vcs device's poll/fasync support relies on the vt notifier to signal changes to the screen content. Notifier invocations were missing for changes that comes through the selection interface though. Fix that. Tested with BRLTTY 5.2. Signed-off-by:
Nicolas Pitre <nico@linaro.org> Cc: Dave Mielke <dave@mielke.cc> Signed-off-by:
-
Alan Stern authored
commit c9919790 upstream. The usb_hcd_unlink_urb() routine in hcd.c contains two possible use-after-free errors. The dev_dbg() statement at the end of the routine dereferences urb and urb->dev even though both structures may have been deallocated. This patch fixes the problem by storing urb->dev in a local variable (avoiding the dereference of urb) and moving the dev_dbg() up before the usb_put_dev() call. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Joe Lawrence <joe.lawrence@stratus.com> Tested-by:
Greg Kroah-Hartman <greg@kroah.com> Signed-off-by:
-
Alan Stern authored
commit 074f9dd5 upstream. Currently the USB stack assumes that all host controller drivers are capable of receiving wakeup requests from downstream devices. However, this isn't true for the isp1760-hcd driver, which means that it isn't safe to do a runtime suspend of any device attached to a root-hub port if the device requires wakeup. This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure and sets the flag in isp1760-hcd. The core is modified to prevent a direct child of the root hub from being put into runtime suspend with wakeup enabled if the flag is set. Signed-off-by:
-
Oliver Neukum authored
commit 7e860a6e upstream. Check the special CDC headers for a plausible minimum length. Another big operating systems ignores such garbage. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Reviewed-by:
Adam Lee <adam8157@gmail.com> Tested-by:
-
Chuck Lever authored
commit 5ae711a2 upstream. If ib_query_qp() fails or the memory registration mode isn't supported, don't leak the PD. An orphaned IB/core resource will cause IB module removal to hang. Fixes: bd7ed1d1 ("RPC/RDMA: check selected memory registration ...") Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Reviewed-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> [lizf: Backported to 3.4: only two goto statements need to be changed] Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit e461894d upstream. StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset by entering the sleep mode. After we have resumed, there is little point in having that bit enabled. Moreover, if this bit is set before reboot, the bootloader can become confused. Thus clear the SMR bit on resume just before clearing the scratchpad (resume address) register. Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Ian Abbott authored
commit 42b8ce6f upstream. `do_cmd_ioctl()` in "comedi_fops.c" handles the `COMEDI_CMD` ioctl. This returns `-EAGAIN` if it has copied a modified `struct comedi_cmd` back to user-space. (This occurs when the low-level Comedi driver's `do_cmdtest()` handler returns non-zero to indicate a problem with the contents of the `struct comedi_cmd`, or when the `struct comedi_cmd` has the `CMDF_BOGUS` flag set.) `compat_cmd()` in "comedi_compat32.c" handles the 32-bit compatible version of the `COMEDI_CMD` ioctl. Currently, it never copies a 32-bit compatible version of `struct comedi_cmd` back to user-space, which is at odds with the way the regular `COMEDI_CMD` ioctl is handled. To fix it, change `compat_cmd()` to copy a 32-bit compatible version of the `struct comedi_cmd` back to user-space when the main ioctl handler returns `-EAGAIN`. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Reviewed-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by:
-
Lennart Sorensen authored
commit a6f03312 upstream. Added the USB serial console device ID for Siemens Ruggedcom devices which have a USB port for their serial console. Signed-off-by:
Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Michel Dänzer authored
commit 16b036af upstream. If the image size would ever read as 0, pci_get_rom_size() could keep processing the same image over and over again. Exit the loop if we ever read a length of zero. This fixes a soft lockup on boot when the radeon driver calls pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card. [bhelgaas: changelog, reference] Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1386973Reported-by:
Federico <federicotg@gmail.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
-
David Hildenbrand authored
commit 0ac96caf upstream. The hrtimer that handles the wait with enabled timer interrupts should not be disturbed by changes of the host time. This patch changes our hrtimer to be based on a monotonic clock. Signed-off-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> Acked-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Andrey Ryabinin authored
commit 6d1cff2a upstream. We hit use after free on dereferncing pointer to task_smack struct in smk_of_task() called from smack_task_to_inode(). task_security() macro uses task_cred_xxx() to get pointer to the task_smack. task_cred_xxx() could be used only for non-pointer members of task's credentials. It cannot be used for pointer members since what they point to may disapper after dropping RCU read lock. Mainly task_security() used this way: smk_of_task(task_security(p)) Intead of this introduce function smk_of_task_struct() which takes task_struct as argument and returns pointer to smk_known struct and do this under RCU read lock. Bogus task_security() macro is not used anymore, so remove it. KASan's report for this: AddressSanitizer: use after free in smack_task_to_inode+0x50/0x70 at addr c4635600 ============================================================================= BUG kmalloc-64 (Tainted: PO): kasan error ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in new_task_smack+0x44/0xd8 age=39 cpu=0 pid=1866 kmem_cache_alloc_trace+0x88/0x1bc new_task_smack+0x44/0xd8 smack_cred_prepare+0x48/0x21c security_prepare_creds+0x44/0x4c prepare_creds+0xdc/0x110 smack_setprocattr+0x104/0x150 security_setprocattr+0x4c/0x54 proc_pid_attr_write+0x12c/0x194 vfs_write+0x1b0/0x370 SyS_write+0x5c/0x94 ret_fast_syscall+0x0/0x48 INFO: Freed in smack_cred_free+0xc4/0xd0 age=27 cpu=0 pid=1564 kfree+0x270/0x290 smack_cred_free+0xc4/0xd0 security_cred_free+0x34/0x3c put_cred_rcu+0x58/0xcc rcu_process_callbacks+0x738/0x998 __do_softirq+0x264/0x4cc do_softirq+0x94/0xf4 irq_exit+0xbc/0x120 handle_IRQ+0x104/0x134 gic_handle_irq+0x70/0xac __irq_svc+0x44/0x78 _raw_spin_unlock+0x18/0x48 sync_inodes_sb+0x17c/0x1d8 sync_filesystem+0xac/0xfc vdfs_file_fsync+0x90/0xc0 vfs_fsync_range+0x74/0x7c INFO: Slab 0xd3b23f50 objects=32 used=31 fp=0xc4635600 flags=0x4080 INFO: Object 0xc4635600 @offset=5632 fp=0x (null) Bytes b4 c46355f0: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ Object c4635600: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object c4635610: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object c4635620: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object c4635630: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk. Redzone c4635640: bb bb bb bb .... Padding c46356e8: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ Padding c46356f8: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ CPU: 5 PID: 834 Comm: launchpad_prelo Tainted: PBO 3.10.30 #1 Backtrace: [<c00233a4>] (dump_backtrace+0x0/0x158) from [<c0023dec>] (show_stack+0x20/0x24) r7:c4634010 r6:d3b23f50 r5:c4635600 r4:d1002140 [<c0023dcc>] (show_stack+0x0/0x24) from [<c06d6d7c>] (dump_stack+0x20/0x28) [<c06d6d5c>] (dump_stack+0x0/0x28) from [<c01c1d50>] (print_trailer+0x124/0x144) [<c01c1c2c>] (print_trailer+0x0/0x144) from [<c01c1e88>] (object_err+0x3c/0x44) r7:c4635600 r6:d1002140 r5:d3b23f50 r4:c4635600 [<c01c1e4c>] (object_err+0x0/0x44) from [<c01cac18>] (kasan_report_error+0x2b8/0x538) r6:d1002140 r5:d3b23f50 r4:c6429cf8 r3:c09e1aa7 [<c01ca960>] (kasan_report_error+0x0/0x538) from [<c01c9430>] (__asan_load4+0xd4/0xf8) [<c01c935c>] (__asan_load4+0x0/0xf8) from [<c031e168>] (smack_task_to_inode+0x50/0x70) r5:c4635600 r4:ca9da000 [<c031e118>] (smack_task_to_inode+0x0/0x70) from [<c031af64>] (security_task_to_inode+0x3c/0x44) r5:cca25e80 r4:c0ba9780 [<c031af28>] (security_task_to_inode+0x0/0x44) from [<c023d614>] (pid_revalidate+0x124/0x178) r6:00000000 r5:cca25e80 r4:cbabe3c0 r3:00008124 [<c023d4f0>] (pid_revalidate+0x0/0x178) from [<c01db98c>] (lookup_fast+0x35c/0x43y4) r9:c6429efc r8:00000101 r7:c079d940 r6:c6429e90 r5:c6429ed8 r4:c83c4148 [<c01db630>] (lookup_fast+0x0/0x434) from [<c01deec8>] (do_last.isra.24+0x1c0/0x1108) [<c01ded08>] (do_last.isra.24+0x0/0x1108) from [<c01dff04>] (path_openat.isra.25+0xf4/0x648) [<c01dfe10>] (path_openat.isra.25+0x0/0x648) from [<c01e1458>] (do_filp_open+0x3c/0x88) [<c01e141c>] (do_filp_open+0x0/0x88) from [<c01ccb28>] (do_sys_open+0xf0/0x198) r7:00000001 r6:c0ea2180 r5:0000000b r4:00000000 [<c01cca38>] (do_sys_open+0x0/0x198) from [<c01ccc00>] (SyS_open+0x30/0x34) [<c01ccbd0>] (SyS_open+0x0/0x34) from [<c001db80>] (ret_fast_syscall+0x0/0x48) Read of size 4 by thread T834: Memory state around the buggy address: c4635380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc c4635400: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc c4635480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc c4635500: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc c4635580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >c4635600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ c4635680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb c4635700: 00 00 00 00 04 fc fc fc fc fc fc fc fc fc fc fc c4635780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc c4635800: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc c4635880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Signed-off-by:
Andrey Ryabinin <a.ryabinin@samsung.com> [lizf: Backported to 3.4: - smk_of_task() returns char* instead of smack_known * - replace task_security() with smk_of_task() with smk_of_task_struct() manually] Signed-off-by:
-
Dmitry Tunin authored
commit 033efa92 upstream. Add support of 13d3:3423 device. BugLink: https://bugs.launchpad.net/bugs/1411193 T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3423 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Matthew Wilcox authored
commit 91117a20 upstream. The 'pfn' returned by axonram was completely bogus, and has been since 2008. Signed-off-by:
Matthew Wilcox <matthew.r.wilcox@intel.com> Reviewed-by:
Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 5efd2ea8 upstream. the following error pops up during "testusb -a -t 10" | musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma) hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in hcd_buffer_alloc() returning memory which is 32 bytes aligned and it might by identified by buffer_offset() as another buffer. This means the buffer which is on a 32 byte boundary will not get freed, instead it tries to free another buffer with the error message. This patch fixes the issue by creating the smallest DMA buffer with the size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is smaller). This might be 32, 64 or even 128 bytes. The next three pools will have the size 128, 512 and 2048. In case the smallest pool is 128 bytes then we have only three pools instead of four (and zero the first entry in the array). The last pool size is always 2048 bytes which is the assumed PAGE_SIZE / 2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where we would end up with 8KiB buffer in case we have 16KiB pages. Instead I think it makes sense to have a common size(s) and extend them if there is need to. There is a BUILD_BUG_ON() now in case someone has a minalign of more than 128 bytes. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by:
-
Ricardo Ribalda Delgado authored
commit 145b3fe5 upstream. Some implementations of modprobe fail to load the driver for a PCI device automatically because the "interface" part of the modalias from the kernel is lowercase, and the modalias from file2alias is uppercase. The "interface" is the low-order byte of the Class Code, defined in PCI r3.0, Appendix D. Most interface types defined in the spec do not use alpha characters, so they won't be affected. For example, 00h, 01h, 10h, 20h, etc. are unaffected. Print the "interface" byte of the Class Code in uppercase hex, as we already do for the Vendor ID, Device ID, Class, etc. Commit 89ec3dcf ("PCI: Generate uppercase hex for modalias interface class") fixed only half of the problem. Some udev implementations rely on the uevent file and not the modalias file. Fixes: d1ded203 ("PCI: add MODALIAS to hotplug event for pci devices") Fixes: 89ec3dcf ("PCI: Generate uppercase hex for modalias interface class") Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
Martin Vajnar authored
commit a52d2093 upstream. Since the removal of CONFIG_REGULATOR_DUMMY option, the touchscreen stopped working. This patch enables the "replacement" for REGULATOR_DUMMY and allows the touchscreen to work even though there is no regulator for "vcc". Signed-off-by:
Martin Vajnar <martin.vajnar@gmail.com> Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit baad2dc4 upstream. Add regulator_has_full_constraints() call to spitz board file to let regulator core know that we do not have any additional regulators left. This lets it substitute unprovided regulators with dummy ones. This fixes the following warnings that can be seen on spitz if regulators are enabled: ads7846 spi2.0: unable to get regulator: -517 spi spi2.0: Driver ads7846 requests probe deferral Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 9bc78f32 upstream. Add regulator_has_full_constraints() call to poodle board file to let regulator core know that we do not have any additional regulators left. This lets it substitute unprovided regulators with dummy ones. This fixes the following warnings that can be seen on poodle if regulators are enabled: ads7846 spi1.0: unable to get regulator: -517 spi spi1.0: Driver ads7846 requests probe deferral wm8731 0-001b: Failed to get supply 'AVDD': -517 wm8731 0-001b: Failed to request supplies: -517 wm8731 0-001b: ASoC: failed to probe component -517 Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 271e8017 upstream. Add regulator_has_full_constraints() call to corgi board file to let regulator core know that we do not have any additional regulators left. This lets it substitute unprovided regulators with dummy ones. This fixes the following warnings that can be seen on corgi if regulators are enabled: ads7846 spi1.0: unable to get regulator: -517 spi spi1.0: Driver ads7846 requests probe deferral wm8731 0-001b: Failed to get supply 'AVDD': -517 wm8731 0-001b: Failed to request supplies: -517 wm8731 0-001b: ASoC: failed to probe component -517 corgi-audio corgi-audio: ASoC: failed to instantiate card -517 Signed-off-by:
-
- 14 Apr, 2015 1 commit
-
-
Zefan Li authored
-
