- 20 Aug, 2016 40 commits
-
-
Oren Givon authored
commit f24bbae5 upstream. Add 6 new 8265 series PCI IDs: - (0x24FD, 0x1130) - (0x24FD, 0x0130) - (0x24FD, 0x0910) - (0x24FD, 0x0930) - (0x24FD, 0x0950) - (0x24FD, 0x0850) Signed-off-by:
Oren Givon <oren.givon@intel.com> Signed-off-by:
David Spinadel <david.spinadel@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Oren Givon authored
commit 4b79deec upstream. Add 3 new 8260 series PCI IDs: - (0x24F3, 0x10B0) - (0x24F3, 0xD0B0) - (0x24F3, 0xB0B0) Signed-off-by:
-
Emmanuel Grumbach authored
commit f16c3ebf upstream. Upon firmware load interrupt (FH_TX), the ISR re-enables the firmware load interrupt only to avoid races with other flows as described in the commit below. When the firmware is completely loaded, the thread that is loading the firmware will enable all the interrupts to make sure that the driver gets the ALIVE interrupt. The problem with that is that the thread that is loading the firmware is actually racing against the ISR and we can get to the following situation: CPU0 CPU1 iwl_pcie_load_given_ucode ... iwl_pcie_load_firmware_chunk wait_for_interrupt <interrupt> ISR handles CSR_INT_BIT_FH_TX ISR wakes up the thread on CPU0 /* enable all the interrupts * to get the ALIVE interrupt */ iwl_enable_interrupts ISR re-enables CSR_INT_BIT_FH_TX only /* start the firmware */ iwl_write32(trans, CSR_RESET, 0); BUG! ALIVE interrupt will never arrive since it has been masked by CPU1. In order to fix that, change the ISR to first check if STATUS_INT_ENABLED is set. If so, re-enable all the interrupts. If STATUS_INT_ENABLED is clear, then we can check what specific interrupt happened and re-enable only that specific interrupt (RFKILL or FH_TX). All the credit for the analysis goes to Kirtika who did the actual debugging work. Fixes: a6bd005f ("iwlwifi: pcie: fix RF-Kill vs. firmware load race") Signed-off-by:
-
Emmanuel Grumbach authored
commit 2aabdbdc upstream. The NIC's CPU gets started after the firmware has been written to its memory. The first thing it does is to send an interrupt to let the driver know that it is running. In order to get that interrupt, the driver needs to make sure it is not masked. Of course, the interrupt needs to be enabled in the driver before the CPU starts to run. I mistakenly inversed those two steps leading to races which prevented the driver from getting the alive interrupt from the firmware. Fix that. Fixes: a6bd005f ("iwlwifi: pcie: fix RF-Kill vs. firmware load race") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Sami Tolvanen authored
commit 602d1657 upstream. do_div was replaced with div64_u64 at some point, causing a bug with block calculation due to incompatible semantics of the two functions. Signed-off-by:
Sami Tolvanen <samitolvanen@google.com> Fixes: a739ff3f ("dm verity: add support for forward error correction") Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Javier Martinez Canillas authored
commit 6311f126 upstream. When s5p_mfc_remove() calls put_device() for the reserved memory region devs, the driver core warns that the dev doesn't have a release callback: WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90 Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed. Also, the declared DMA memory using dma_declare_coherent_memory() isn't relased so add a dev .release that calls dma_release_declared_memory(). Fixes: 6e83e6e2 ("[media] s5p-mfc: Fix kernel warning on memory init") Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Tested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Javier Martinez Canillas authored
commit 29debab0 upstream. The devices don't have a name set, so makes dev_name() returns NULL which makes harder to identify the devices that are causing issues, for example: WARNING: CPU: 2 PID: 616 at drivers/base/core.c:251 device_release+0x8c/0x90 Device '(null)' does not have a release() function, it is broken and must be fixed. And after setting the device name: WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90 Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed. Fixes: 6e83e6e2 ("[media] s5p-mfc: Fix kernel warning on memory init") Signed-off-by:
-
Alex Hung authored
commit fc8a601e upstream. Several users reported wifi cannot be unblocked as discussed in [1]. This patch removes the use of the 2009 flag by BIOS but uses the actual WMI function calls - it will be skipped if WMI reports unsupported. [1] https://bugzilla.kernel.org/show_bug.cgi?id=69131Signed-off-by:
Alex Hung <alex.hung@canonical.com> Tested-by:
Evgenii Shatokhin <eugene.shatokhin@yandex.ru> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Dave Chinner authored
commit 28b783e4 upstream. In xfs_finish_page_writeback(), we have a loop that looks like this: do { if (off < bvec->bv_offset) goto next_bh; if (off > end) break; bh->b_end_io(bh, !error); next_bh: off += bh->b_size; } while ((bh = bh->b_this_page) != head); The b_end_io function is end_buffer_async_write(), which will call end_page_writeback() once all the buffers have marked as no longer under IO. This issue here is that the only thing currently protecting both the bufferhead chain and the page from being reclaimed is the PageWriteback state held on the page. While we attempt to limit the loop to just the buffers covered by the IO, we still read from the buffer size and follow the next pointer in the bufferhead chain. There is no guarantee that either of these are valid after the PageWriteback flag has been cleared. Hence, loops like this are completely unsafe, and result in use-after-free issues. One such problem was caught by Calvin Owens with KASAN: ..... INFO: Freed in 0x103fc80ec age=18446651500051355200 cpu=2165122683 pid=-1 free_buffer_head+0x41/0x90 __slab_free+0x1ed/0x340 kmem_cache_free+0x270/0x300 free_buffer_head+0x41/0x90 try_to_free_buffers+0x171/0x240 xfs_vm_releasepage+0xcb/0x3b0 try_to_release_page+0x106/0x190 shrink_page_list+0x118e/0x1a10 shrink_inactive_list+0x42c/0xdf0 shrink_zone_memcg+0xa09/0xfa0 shrink_zone+0x2c3/0xbc0 ..... Call Trace: <IRQ> [<ffffffff81e8b8e4>] dump_stack+0x68/0x94 [<ffffffff8153a995>] print_trailer+0x115/0x1a0 [<ffffffff81541174>] object_err+0x34/0x40 [<ffffffff815436e7>] kasan_report_error+0x217/0x530 [<ffffffff81543b33>] __asan_report_load8_noabort+0x43/0x50 [<ffffffff819d651f>] xfs_destroy_ioend+0x3bf/0x4c0 [<ffffffff819d69d4>] xfs_end_bio+0x154/0x220 [<ffffffff81de0c58>] bio_endio+0x158/0x1b0 [<ffffffff81dff61b>] blk_update_request+0x18b/0xb80 [<ffffffff821baf57>] scsi_end_request+0x97/0x5a0 [<ffffffff821c5558>] scsi_io_completion+0x438/0x1690 [<ffffffff821a8d95>] scsi_finish_command+0x375/0x4e0 [<ffffffff821c3940>] scsi_softirq_done+0x280/0x340 Where the access is occuring during IO completion after the buffer had been freed from direct memory reclaim. Prevent use-after-free accidents in this end_io processing loop by pre-calculating the loop conditionals before calling bh->b_end_io(). The loop is already limited to just the bufferheads covered by the IO in progress, so the offset checks are sufficient to prevent accessing buffers in the chain after end_page_writeback() has been called by the the bh->b_end_io() callout. Yet another example of why Bufferheads Must Die. Signed-off-by:
Dave Chinner <dchinner@redhat.com> Reported-and-Tested-by:
Calvin Owens <calvinowens@fb.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Brian Foster <bfoster@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Mike Snitzer authored
commit eaf9a736 upstream. Otherwise, there is potential for both DMF_SUSPENDED* and DMF_NOFLUSH_SUSPENDING to not be set during dm_suspend() -- which is definitely _not_ a valid state. This fix, in conjuction with "dm rq: fix the starting and stopping of blk-mq queues", addresses the potential for request-based DM multipath's __multipath_map() to see !dm_noflush_suspending() during suspend. Reported-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
-
Tahsin Erdogan authored
commit bd9f55ea upstream. Commit d548b34b ("dm: reduce the queue delay used in dm_request_fn from 100ms to 10ms") always intended the value to be 10 msecs -- it just expressed it in jiffies because earlier commit 7eaceacc ("block: remove per-queue plugging") did. Signed-off-by:
Tahsin Erdogan <tahsin@google.com> Signed-off-by:
-
Alim Akhtar authored
commit 04c16b84 upstream. This patch fixes some of the LDOs and BUCKs voltage range as per user manual of s2mps15 (REV0.4). Fixes: 51af2067 ("regulator: s2mps11: Add support for S2MPS15 regulators") Signed-off-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Florian Echtler authored
commit 6a858815 upstream. Closing the V4L2 device sometimes triggers a kernel oops. Present patch fixes this. Signed-off-by:
Martin Kaltenbrunner <modin@yuri.at> Signed-off-by:
Florian Echtler <floe@butterbrot.org> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Florian Echtler authored
commit af766ee0 upstream. The framerate sometimes drops below 60 Hz if the poll interval is too high. Lowering it to the minimum of 1 ms fixes this. Signed-off-by:
-
Jonathan McDowell authored
commit bbdb34c9 upstream. Fix RC5 decoding with Fintek CIR chipset Commit e87b540b tightened up the RC5 decoding by adding a check for trailing silence to ensure a valid RC5 command had been received. Unfortunately the trailer length checked was 10 units and the Fintek CIR device does not want to provide details of a space longer than 6350us. This meant that RC5 remotes working on a Fintek setup on 3.16 failed on 3.17 and later. Fix this by shortening the trailer check to 6 units (allowing for a previous space in the received remote command). Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117221Signed-off-by:
Jonathan McDowell <noodles@earth.li> Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
Sakari Ailus authored
commit 126f4029 upstream. An earlier patch fixing an input validation issue introduced another issue: vb2_core_dqbuf() is called with pb argument value NULL in some cases, causing a NULL pointer dereference. Fix this by skipping the verification as there's nothing to verify. Fixes: e7e0c3e2 ("[media] videobuf2-core: Check user space planes array in dqbuf") Signed-off-by:
David R <david@unsolicited.net> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by:
-
Sakari Ailus authored
commit 83934b75 upstream. When a buffer is being dequeued using VIDIOC_DQBUF IOCTL, the exact buffer which will be dequeued is not known until the buffer has been removed from the queue. The number of planes is specific to a buffer, not to the queue. This does lead to the situation where multi-plane buffers may be requested and queued with n planes, but VIDIOC_DQBUF IOCTL may be passed an argument struct with fewer planes. __fill_v4l2_buffer() however uses the number of planes from the dequeued videobuf2 buffer, overwriting kernel memory (the m.planes array allocated in video_usercopy() in v4l2-ioctl.c) if the user provided fewer planes than the dequeued buffer had. Oops! Fixes: b0e0e1f8 ("[media] media: videobuf2: Prepare to divide videobuf2") Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Heiner Kallweit authored
commit 5cac1f67 upstream. If a system configures the Nuvoton chip to use the alternative EFM IO address (CR_EFIR2) then after probing the primary EFM IO address (CR_EFIR) this region is not released. If a driver for another function of the Nuvoton Super I/O chip uses the same probing mechanism then it will hang if loaded after the nuvoton-cir driver. This was reported for the nct6775 hwmon driver. Fix this by properly releasing the region after probing CR_EFIR. This regression was introduced with kernel 4.6 so cc it to stable. Reported-by:
Antti Seppälä <a.seppala@gmail.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Tested-by:
-
Soeren Moch authored
commit ca6e6126 upstream. Implement memory barriers according to Documentation/circular-buffers.txt: - use smp_store_release() to update ringbuffer read/write pointers - use smp_load_acquire() to load write pointer on reader side - use ACCESS_ONCE() to load read pointer on writer side This fixes data stream corruptions observed e.g. on an ARM Cortex-A9 quad core system with different types (PCI, USB) of DVB tuners. Signed-off-by:
Soeren Moch <smoch@web.de> Signed-off-by:
-
Matthew Leach authored
commit 2a00932f upstream. When disconnecting the usbtv device, the sound card is unregistered from ALSA and the snd member of the usbtv struct is set to NULL. If the usbtv snd_trigger work is running, this can cause a race condition where the kernel will attempt to access free'd resources, shown in [1]. This patch fixes the disconnection code by cancelling any snd_trigger work before unregistering the sound card from ALSA and checking that the snd member still exists in the work function. [1]: usb 3-1.2: USB disconnect, device number 6 BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 IP: [<ffffffff81093850>] process_one_work+0x30/0x480 PGD 405bbf067 PUD 405bbe067 PMD 0 Call Trace: [<ffffffff81093ce8>] worker_thread+0x48/0x4e0 [<ffffffff81093ca0>] ? process_one_work+0x480/0x480 [<ffffffff81093ca0>] ? process_one_work+0x480/0x480 [<ffffffff81099998>] kthread+0xd8/0xf0 [<ffffffff815c73c2>] ret_from_fork+0x22/0x40 [<ffffffff810998c0>] ? kthread_worker_fn+0x170/0x170 ---[ end trace 0f3dac5c1a38e610 ]--- Signed-off-by:
Matthew Leach <matthew@mattleach.net> Tested-by:
Peter Sutton <foxxy@foxdogstudios.com> Signed-off-by:
-
Paul Gortmaker authored
commit 5cada174 upstream. To fix: Untracked files: (use "git add <file>..." to include in what will be committed) tools/objtool/fixdep Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/a4571f6893caf737d05524cfa3829c2abc1fb240.1469452729.git.jpoimboe@redhat.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Kan Liang authored
commit 10e9e7bd upstream. Some uncore boxes' num_counters value for Haswell server and Broadwell server are not correct (too large, off by one). This issue was found by comparing the code with the document. Although there is no bug report from users yet, accessing non-existent counters is dangerous and the behavior is undefined: it may cause miscounting or even crashes. This patch makes them consistent with the uncore document. Reported-by:
Lukasz Odzioba <lukasz.odzioba@intel.com> Signed-off-by:
Kan Liang <kan.liang@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: http://lkml.kernel.org/r/1470925820-59847-1-git-send-email-kan.liang@intel.comSigned-off-by:
-
Linus Walleij authored
commit f37be01e upstream. The RPM has two sets of selectors (IPC bit fields): request and acknowledge. Apparently, some models use 4*32 bit words for select and some use 7*32 bit words for request, but all use 7*32 words for acknowledge bits. So apparently you can on the models with requests of 4*32 select bits send 4*32 messages and get 7*32 different replies, so on ACK interrupt, 7*32 bit words need to be read. This is how the vendor code apparently works. Reported-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Linus Walleij authored
commit 9835f1b7 upstream. The RPM in MSM8660/APQ8060 has different offsets to the selector ACK and request context ACK registers. Make all these register offsets part of the per-SoC data and assign the right values. The bug was found by verifying backwards to the vendor tree in the out-of-tree files <mach/rpm-[8660|8064|8960]>: all were using offsets 3,11,15,23 and a select size of 4, except the MSM8660/APQ8060 which was using offsets 3,11,19,27 and a select size of 7. All other platforms apart from msm8660 were affected by reading excess registers, since 7 was hardcoded as the number of select words, this patch makes also this part dynamic so we only write/read as many select words as the platform actually use. Symptoms of this bug when using msm8660: the first RPM transaction would work, but the next would stall or raise an error since the previous transaction was not properly ACKed as the ACK words were read at the wrong offset. Fixes: 58e21438 ("mfd: qcom-rpm: Driver for the Qualcomm RPM") Signed-off-by:
-
Jan Kiszka authored
commit 5fc8f707 upstream. If MSR_CONFIG_TDP_CONTROL is locked, we currently try to address some MSR 0x80000648 or so. Mask out the relevant level bits 0 and 1. Found while running over the Jailhouse hypervisor which became upset about this strange MSR index. Signed-off-by:
Jan Kiszka <jan.kiszka@siemens.com> Acked-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
David Hildenbrand authored
commit c427c42c upstream. Commit 1e133ab2 ("s390/mm: split arch/s390/mm/pgtable.c") changed the return value of get_guest_storage_key to an unsigned char, resulting in -EFAULT getting interpreted as a valid storage key. Reviewed-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by:
-
David Hildenbrand authored
commit f0454029 upstream. __tlb_flush_asce() should never be used if multiple asce belong to a mm. As this function changes mm logic determining if local or global tlb flushes will be neded, we might end up flushing only the gmap asce on all CPUs and a follow up mm asce flushes will only flush on the local CPU, although that asce ran on multiple CPUs. The missing tlb flushes will provoke strange faults in user space and even low address protections in user space, crashing the kernel. Fixes: 1b948d6c ("s390/mm,tlb: optimize TLB flushing for zEC12") Reported-by:
Sascha Silbe <silbe@linux.vnet.ibm.com> Acked-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Sebastian Ott authored
commit 0f5d050c upstream. Prior to commit 1bc6664b a call to enable_cmf for a device for which channel measurement was already enabled resulted in a reset of the measurement data. What looked like bugs at the time (a 2nd allocation was triggered but failed, reset was called regardless of previous failures, and errors have not been reported to userspace) was actually something at least one userspace tool depended on. Restore that behavior in a sane way. Fixes: 1bc6664b ("s390/cio: use device_lock during cmb activation") Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Reviewed-by:
Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by:
-
Paolo Bonzini authored
commit c43203ca upstream. If the processor exits to KVM while delivering an interrupt, the hypervisor then requeues the interrupt for the next vmentry. Trying to enter SMM in this same window causes to enter non-root mode in emulated SMM (i.e. with IF=0) and with a request to inject an IRQ (i.e. with a valid VM-entry interrupt info field). This is invalid guest state (SDM 26.3.1.4 "Check on Guest RIP and RFLAGS") and the processor fails vmentry. The fix is to defer the injection from KVM_REQ_SMI to KVM_REQ_EVENT, like we already do for e.g. NMIs. This patch doesn't change the name of the process_smi function so that it can be applied to stable releases. The next patch will modify the names so that process_nmi and process_smi handle respectively KVM_REQ_NMI and KVM_REQ_SMI. This is especially common with Windows, probably due to the self-IPI trick that it uses to deliver deferred procedure calls (DPCs). Reported-by:
Laszlo Ersek <lersek@redhat.com> Reported-by:
Michał Zegan <webczat_200@poczta.onet.pl> Fixes: 64d60670Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Jim Mattson authored
commit 2f1fe811 upstream. When freeing the nested resources of a vcpu, there is an assumption that the vcpu's vmcs01 is the current VMCS on the CPU that executes nested_release_vmcs12(). If this assumption is violated, the vcpu's vmcs01 may be made active on multiple CPUs at the same time, in violation of Intel's specification. Moreover, since the vcpu's vmcs01 is not VMCLEARed on every CPU on which it is active, it can linger in a CPU's VMCS cache after it has been freed and potentially repurposed. Subsequent eviction from the CPU's VMCS cache on a capacity miss can result in memory corruption. It is not sufficient for vmx_free_vcpu() to call vmx_load_vmcs01(). If the vcpu in question was last loaded on a different CPU, it must be migrated to the current CPU before calling vmx_load_vmcs01(). Signed-off-by:
Jim Mattson <jmattson@google.com> Signed-off-by:
-
Cao, Lei authored
commit b244c9fc upstream. With PML enabled, guest will shut down if a PML full VMEXIT occurs during event delivery. According to Intel SDM 27.2.3, PML full VMEXIT can occur when event is being delivered through IDT, so KVM should not exit to user space with error. Instead, it should let EXIT_REASON_PML_FULL go through and the event will be re-injected on the next VMENTRY. Signed-off-by:
Lei Cao <lei.cao@stratus.com> Fixes: 843e4330 ("KVM: VMX: Add PML support in VMX") [Shortened the summary and Cc'd stable.] Signed-off-by:
-
Alexis Dambricourt authored
commit 30b072ce upstream. The following #PF may occurs: [ 1403.317041] BUG: unable to handle kernel paging request at 0000000200000068 [ 1403.317045] IP: [<ffffffffc04c20b0>] __mtrr_lookup_var_next+0x10/0xa0 [kvm] [ 1403.317123] Call Trace: [ 1403.317134] [<ffffffffc04c2a65>] ? kvm_mtrr_check_gfn_range_consistency+0xc5/0x120 [kvm] [ 1403.317143] [<ffffffffc04ac11f>] ? tdp_page_fault+0x9f/0x2c0 [kvm] [ 1403.317152] [<ffffffffc0498128>] ? kvm_set_msr_common+0x858/0xc00 [kvm] [ 1403.317161] [<ffffffffc04b8883>] ? x86_emulate_insn+0x273/0xd30 [kvm] [ 1403.317171] [<ffffffffc04c04e4>] ? kvm_cpuid+0x34/0x190 [kvm] [ 1403.317180] [<ffffffffc04a5bb9>] ? kvm_mmu_page_fault+0x59/0xe0 [kvm] [ 1403.317183] [<ffffffffc0d729e1>] ? vmx_handle_exit+0x1d1/0x14a0 [kvm_intel] [ 1403.317185] [<ffffffffc0d75f3f>] ? atomic_switch_perf_msrs+0x6f/0xa0 [kvm_intel] [ 1403.317187] [<ffffffffc0d7621d>] ? vmx_vcpu_run+0x2ad/0x420 [kvm_intel] [ 1403.317196] [<ffffffffc04a0962>] ? kvm_arch_vcpu_ioctl_run+0x622/0x1550 [kvm] [ 1403.317204] [<ffffffffc049abb9>] ? kvm_arch_vcpu_load+0x59/0x210 [kvm] [ 1403.317206] [<ffffffff81036245>] ? __kernel_fpu_end+0x35/0x100 [ 1403.317213] [<ffffffffc0487eb6>] ? kvm_vcpu_ioctl+0x316/0x5d0 [kvm] [ 1403.317215] [<ffffffff81088225>] ? do_sigtimedwait+0xd5/0x220 [ 1403.317217] [<ffffffff811f84dd>] ? do_vfs_ioctl+0x9d/0x5c0 [ 1403.317224] [<ffffffffc04928ae>] ? kvm_on_user_return+0x3e/0x70 [kvm] [ 1403.317225] [<ffffffff811f8a74>] ? SyS_ioctl+0x74/0x80 [ 1403.317227] [<ffffffff815bf0b6>] ? entry_SYSCALL_64_fastpath+0x1e/0xa8 [ 1403.317242] RIP [<ffffffffc04c20b0>] __mtrr_lookup_var_next+0x10/0xa0 [kvm] At mtrr_lookup_fixed_next(), when the condition 'if (iter->index >= ARRAY_SIZE(iter->mtrr_state->fixed_ranges))' becomes true, mtrr_lookup_var_start() is called with iter->range with gargabe values from the fixed MTRR union field. Then, list_prepare_entry() do not call list_entry() initialization, keeping a garbage pointer in iter->range which is accessed in the following __mtrr_lookup_var_next() call. Fixes: f571c097Signed-off-by:
Alexis Dambricourt <alexis@blade-group.com> Signed-off-by:
-
Paul Mackerras authored
commit 93d17397 upstream. It turns out that if the guest does a H_CEDE while the CPU is in a transactional state, and the H_CEDE does a nap, and the nap loses the architected state of the CPU (which is is allowed to do), then we lose the checkpointed state of the virtual CPU. In addition, the transactional-memory state recorded in the MSR gets reset back to non-transactional, and when we try to return to the guest, we take a TM bad thing type of program interrupt because we are trying to transition from non-transactional to transactional with a hrfid instruction, which is not permitted. The result of the program interrupt occurring at that point is that the host CPU will hang in an infinite loop with interrupts disabled. Thus this is a denial of service vulnerability in the host which can be triggered by any guest (and depending on the guest kernel, it can potentially triggered by unprivileged userspace in the guest). This vulnerability has been assigned the ID CVE-2016-5412. To fix this, we save the TM state before napping and restore it on exit from the nap, when handling a H_CEDE in real mode. The case where H_CEDE exits to host virtual mode is already OK (as are other hcalls which exit to host virtual mode) because the exit path saves the TM state. Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Paul Mackerras authored
commit f024ee09 upstream. This moves the transactional memory state save and restore sequences out of the guest entry/exit paths into separate procedures. This is so that these sequences can be used in going into and out of nap in a subsequent patch. The only code changes here are (a) saving and restore LR on the stack, since these new procedures get called with a bl instruction, (b) explicitly saving r1 into the PACA instead of assuming that HSTATE_HOST_R1(r13) is already set, and (c) removing an unnecessary and redundant setting of MSR[TM] that should have been removed by commit 9d4d0bdd9e0a ("KVM: PPC: Book3S HV: Add transactional memory support", 2013-09-24) but wasn't. Signed-off-by:
-
Mark Rutland authored
commit dfbca61a upstream. In create_safe_exec_page(), we create a copy of the hibernate exit text, along with some page tables to map this via TTBR0. We then install the new tables in TTBR0. In swsusp_arch_resume() we call create_safe_exec_page() before trying a number of operations which may fail (e.g. copying the linear map page tables). If these fail, we bail out of swsusp_arch_resume() and return an error code, but leave TTBR0 as-is. Subsequently, the core hibernate code will call free_basic_memory_bitmaps(), which will free all of the memory allocations we made, including the page tables installed in TTBR0. Thus, we may have TTBR0 pointing at dangling freed memory for some period of time. If the hibernate attempt was triggered by a user requesting a hibernate test via the reboot syscall, we may return to userspace with the clobbered TTBR0 value. Avoid these issues by reorganising swsusp_arch_resume() such that we have no failure paths after create_safe_exec_page(). We also add a check that the zero page allocation succeeded, matching what we have for other allocations. Fixes: 82869ac5 ("arm64: kernel: Add support for hibernate/suspend-to-disk") Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Acked-by:
James Morse <james.morse@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Mark Rutland authored
commit 0194e760 upstream. In create_safe_exec_page we install a set of global mappings in TTBR0, then subsequently invalidate TLBs. While TTBR0 points at the zero page, and the TLBs should be free of stale global entries, we may have stale ASID-tagged entries (e.g. from the EFI runtime services mappings) for the same VAs. Per the ARM ARM these ASID-tagged entries may conflict with newly-allocated global entries, and we must follow a Break-Before-Make approach to avoid issues resulting from this. This patch reworks create_safe_exec_page to invalidate TLBs while the zero page is still in place, ensuring that there are no potential conflicts when the new TTBR0 value is installed. As a single CPU is online while this code executes, we do not need to perform broadcast TLB maintenance, and can call local_flush_tlb_all(), which also subsumes some barriers. The remaining assembly is converted to use write_sysreg() and isb(). Other than this, we safely manipulate TTBRs in the hibernate dance. The code we install as part of the new TTBR0 mapping (the hibernated kernel's swsusp_arch_suspend_exit) installs a zero page into TTBR1, invalidates TLBs, then installs its preferred value. Upon being restored to the middle of swsusp_arch_suspend, the new image will call __cpu_suspend_exit, which will call cpu_uninstall_idmap, installing the zero page in TTBR0 and invalidating all TLB entries. Fixes: 82869ac5 ("arm64: kernel: Add support for hibernate/suspend-to-disk") Signed-off-by:
-
Andrew Jones authored
commit 89581f06 upstream. We need to set cpsr before determining the spsr bank, as the bank depends on the target exception level of the injection, not the current mode of the vcpu. Normally this is one in the same (EL1), but not when we manage to trap an EL0 fault. It still doesn't really matter for the 64-bit EL0 case though, as vcpu_spsr() unconditionally uses the EL1 bank for that. However the 32-bit EL0 case gets fun, as that path will lead to the BUG() in vcpu_spsr32(). This patch fixes the assignment order and also modifies some white space in order to better group pairs of lines that have strict order. Signed-off-by:
Andrew Jones <drjones@redhat.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Ard Biesheuvel authored
commit d6732fc4 upstream. Due to the untyped KIMAGE_VADDR constant, the linker may not notice that the __rela_offset and __dynsym_offset expressions are absolute values (i.e., are not subject to relocation). This does not matter for KASLR, but it does confuse kallsyms in relative mode, since it uses the lowest non-absolute symbol address as the anchor point, and expects all other symbol addresses to be within 4 GB of it. Fix this by qualifying these expressions as ABSOLUTE() explicitly. Fixes: 0cd3defe ("arm64: kernel: perform relocation processing from ID map") Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Ard Biesheuvel authored
commit 04a84810 upstream. As reported by Zijun, the fdt_check_header() call in __fixmap_remap_fdt() is not safe since it is not guaranteed that the FDT header is mapped completely. Due to the minimum alignment of 8 bytes, the only fields we can assume to be mapped are 'magic' and 'totalsize'. Since the OF layer is in charge of validating the FDT image, and we are only interested in making reasonably sure that the size field contains a meaningful value, replace the fdt_check_header() call with an explicit comparison of the magic field's value against the expected value. Reported-by:
Zijun Hu <zijun_hu@htc.com> Acked-by:
-
Caesar Wang authored
commit ad1cfdf5 upstream. The 2nd additional region is the GIC virtual cpu interface register base and size. As the gic400 of rk3368 says, the cpu interface register map as below : -0x0000 GICC_CTRL . . . -0x00fc GICC_IIDR -0x1000 GICC_IDR Obviously, the region size should be greater than 0x1000. So we should make sure to include the GICC_IDR since the kernel will access it in some cases. Fixes: b790c2ca ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board") Signed-off-by:
Caesar Wang <wxt@rock-chips.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Heiko Stuebner <heiko@sntech.de>
-
