- 13 Apr, 2020 2 commits
-
-
William Dauchy authored
[ Upstream commit 25629fda ] when creating a new ipip interface with no local/remote configuration, the lookup is done with TUNNEL_NO_KEY flag, making it impossible to match the new interface (only possible match being fallback or metada case interface); e.g: `ip link add tunl1 type ipip dev eth0` To fix this case, adding a flag check before the key comparison so we permit to match an interface with no local/remote config; it also avoids breaking possible userland tools relying on TUNNEL_NO_KEY flag and uninitialised key. context being on my side, I'm creating an extra ipip interface attached to the physical one, and moving it to a dedicated namespace. Fixes: c5441932 ("GRE: Refactor GRE tunneling code.") Signed-off-by:
William Dauchy <w.dauchy@criteo.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Qian Cai authored
[ Upstream commit fbe4e0c1 ] fib_triestat_seq_show() calls hlist_for_each_entry_rcu(tb, head, tb_hlist) without rcu_read_lock() will trigger a warning, net/ipv4/fib_trie.c:2579 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by proc01/115277: #0: c0000014507acf00 (&p->lock){+.+.}-{3:3}, at: seq_read+0x58/0x670 Call Trace: dump_stack+0xf4/0x164 (unreliable) lockdep_rcu_suspicious+0x140/0x164 fib_triestat_seq_show+0x750/0x880 seq_read+0x1a0/0x670 proc_reg_read+0x10c/0x1b0 __vfs_read+0x3c/0x70 vfs_read+0xac/0x170 ksys_read+0x7c/0x140 system_call+0x5c/0x68 Fix it by adding a pair of rcu_read_lock/unlock() and use cond_resched_rcu() to avoid the situation where walking of a large number of items may prevent scheduling for a long time. Signed-off-by:
Qian Cai <cai@lca.pw> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
- 02 Apr, 2020 38 commits
-
-
Greg Kroah-Hartman authored
-
Madalin Bucur authored
commit d79e9d7c upstream. The correct setting for the RGMII ports on LS1046ARDB is to enable delay on both Rx and Tx so the interface mode used must be PHY_INTERFACE_MODE_RGMII_ID. Since commit 1b3047b5 ("net: phy: realtek: add support for configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver has control over the RGMII RX delay and it is disabling it for RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but in the device tree the mode was described as "rgmii". Changing the phy-connection-type to "rgmii-id" to address the issue. Fixes: 3fa395d2 ("arm64: dts: add LS1046A DPAA FMan nodes") Signed-off-by:
Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by:
-
Madalin Bucur authored
commit 4022d808 upstream. The correct setting for the RGMII ports on LS1043ARDB is to enable delay on both Rx and Tx so the interface mode used must be PHY_INTERFACE_MODE_RGMII_ID. Since commit 1b3047b5 ("net: phy: realtek: add support for configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver has control over the RGMII RX delay and it is disabling it for RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but in the device tree the mode was described as "rgmii_txid". This issue was not apparent at the time as the PHY driver took the same action for RGMII_TXID and RGMII_ID back then but it became visible (RX no longer working) after the above patch. Changing the phy-connection-type to "rgmii-id" to address the issue. Fixes: bf02f2ff ("arm64: dts: add LS1043A DPAA FMan support") Signed-off-by:
-
Arthur Demchenkov authored
commit 0c5220a3 upstream. Commit a758f50f ("mtd: onenand: omap2: Configure driver from DT") started using DT specified timings for GPMC, and as a result the OneNAND stopped working on N900 as we had wrong values in the DT. Fix by updating the values to bootloader timings that have been tested to be working on Nokia N900 with OneNAND manufacturers: Samsung, Numonyx. Fixes: a758f50f ("mtd: onenand: omap2: Configure driver from DT") Signed-off-by:
Arthur Demchenkov <spinal.by@gmail.com> Tested-by:
Merlijn Wajer <merlijn@wizzup.org> Reviewed-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Marco Felsch authored
commit 636b45b8 upstream. The current set minimum voltage of 730000µV seems to be wrong. I don't know the document which specifies that but the imx6qdl datasheets says that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed, lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp). Fixes: ddec5d1c ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM") Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Nick Hudson authored
commit 6687c201 upstream. Define the sdhci pinctrl state as "default" so it gets applied correctly and to match all other RPis. Fixes: 2c7c040c ("ARM: dts: bcm2835: Add Raspberry Pi Zero W") Signed-off-by:
Nick Hudson <skrll@netbsd.org> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Sungbo Eo authored
commit deeabb4c upstream. Disable all rps-irq interrupts during driver initialization to prevent an accidental interrupt on GIC. Fixes: 84316f4e ("ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi") Fixes: 38d4a537 ("ARM: dts: Add support for OX820 and Pogoplug V3") Signed-off-by:
Sungbo Eo <mans0n@gorani.run> Acked-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
disconnect3d authored
commit db2c5494 upstream. This patch fixes an off-by-one error in strncpy size argument in tools/perf/util/map.c. The issue is that in: strncmp(filename, "/system/lib/", 11) the passed string literal: "/system/lib/" has 12 bytes (without the NULL byte) and the passed size argument is 11. As a result, the logic won't match the ending "/" byte and will pass filepaths that are stored in other directories e.g. "/system/libmalicious/bin" or just "/system/libmalicious". This functionality seems to be present only on Android. I assume the /system/ directory is only writable by the root user, so I don't think this bug has much (or any) security impact. Fixes: eca81836 ("perf tools: Add automatic remapping of Android libraries") Signed-off-by:
disconnect3d <dominik.b.czarnota@gmail.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Changbin Du <changbin.du@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Keeping <john@metanate.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Lentine <mlentine@google.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Ilie Halip authored
commit 6f5459da upstream. Building an arm64 defconfig with clang's integrated assembler, this error occurs: <instantiation>:2:2: error: unrecognized instruction mnemonic _ASM_EXTABLE 9999b, 9f ^ arch/arm64/mm/cache.S:50:1: note: while in macro instantiation user_alt 9f, "dc cvau, x4", "dc civac, x4", 0 ^ While GNU as seems fine with case-sensitive macro instantiations, clang doesn't, so use the actual macro name (_asm_extable) as in the rest of the file. Also checked that the generated assembly matches the GCC output. Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Tested-by:
Ilie Halip <ilie.halip@gmail.com> Signed-off-by:
Will Deacon <will@kernel.org> Signed-off-by:
-
Marek Vasut authored
commit 8262e6f9 upstream. This patch reverts 58292104 ("net: ks8851-ml: Fix 16-bit IO operation") and edacb098 ("net: ks8851-ml: Fix 16-bit data access"), because it turns out these were only necessary due to buggy hardware. This patch adds a check for such a buggy hardware to prevent any such mistakes again. While working further on the KS8851 driver, it came to light that the KS8851-16MLL is capable of switching bus endianness by a hardware strap, EESK pin. If this strap is incorrect, the IO accesses require such endian swapping as is being reverted by this patch. Such swapping also impacts the performance significantly. Hence, in addition to removing it, detect that the hardware is broken, report to user, and fail to bind with such hardware. Fixes: 58292104 ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098 ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by:
Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Hans de Goede authored
commit 0c625ccf upstream. There are at least 3 models of the HP x2 10 models: Bay Trail SoC + AXP288 PMIC Cherry Trail SoC + AXP288 PMIC Cherry Trail SoC + TI PMIC Like on the other HP x2 10 models we need to ignore wakeup for ACPI GPIO events on the external embedded-controller pin to avoid spurious wakeups on the HP x2 10 CHT + AXP288 model too. This commit adds an extra DMI based quirk for the HP x2 10 CHT + AXP288 model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin on this model. This fixes spurious wakeups from suspend on this model. Fixes: aa23ca3d ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism") Reported-and-tested-by:
Marc Lehmann <schmorp@schmorp.de> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200302111225.6641-4-hdegoede@redhat.comAcked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 5c6f2588 upstream. Trying to initialize a structure with "= {};" will not always clean out all padding locations in a structure. So be explicit and call memset to initialize everything for a number of bpf information structures that are then copied from userspace, sometimes from smaller memory locations than the size of the structure. Reported-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20200320162258.GA794295@kroah.comSigned-off-by:
-
Greg Kroah-Hartman authored
commit 8096f229 upstream. For the bpf syscall, we are relying on the compiler to properly zero out the bpf_attr union that we copy userspace data into. Unfortunately that doesn't always work properly, padding and other oddities might not be correctly zeroed, and in some tests odd things have been found when the stack is pre-initialized to other values. Fix this by explicitly memsetting the structure to 0 before using it. Reported-by:
Maciej Żenczykowski <maze@google.com> Reported-by:
John Stultz <john.stultz@linaro.org> Reported-by:
Alexander Potapenko <glider@google.com> Reported-by:
Alistair Delva <adelva@google.com> Signed-off-by:
-
Georg Müller authored
commit 95b31e35 upstream. The Lex 2I385SW board has two Intel I211 ethernet controllers. Without this patch, only the first port is usable. The second port fails to start with the following message: igb: probe of 0000:02:00.0 failed with error -2 Fixes: 648e9218 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Tested-by:
Georg Müller <georgmueller@gmx.net> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Eric Biggers authored
commit 7cf64b18 upstream. vt_in_use() dereferences console_driver->ttys[i] without proper locking. This is broken because the tty can be closed and freed concurrently. We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL' and skipping the check of tty_struct::count. But, looking at console_driver->ttys[i] isn't really appropriate anyway because even if it is NULL the tty can still be in the process of being closed. Instead, fix it by making vt_in_use() require console_lock() and check whether the vt is allocated and has port refcount > 1. This works since following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console" the port refcount is incremented while the vt is open. Reproducer (very unreliable, but it worked for me after a few minutes): #include <fcntl.h> #include <linux/vt.h> int main() { int fd, nproc; struct vt_stat state; char ttyname[16]; fd = open("/dev/tty10", O_RDONLY); for (nproc = 1; nproc < 8; nproc *= 2) fork(); for (;;) { sprintf(ttyname, "/dev/tty%d", rand() % 8); close(open(ttyname, O_RDONLY)); ioctl(fd, VT_GETSTATE, &state); } } KASAN report: BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline] BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657 Read of size 4 at addr ffff888065722468 by task syz-vt2/132 CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d36 #13 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014 Call Trace: [...] vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline] vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657 tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660 [...] Allocated by task 136: [...] kzalloc include/linux/slab.h:669 [inline] alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982 tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334 tty_open_by_driver drivers/tty/tty_io.c:1987 [inline] tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035 [...] Freed by task 41: [...] kfree+0xbf/0x200 mm/slab.c:3757 free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177 release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468 process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264 worker_thread+0x8b/0xc80 kernel/workqueue.c:2410 [...] Fixes: 4001d7b7 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Acked-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.orgSigned-off-by:
-
Eric Biggers authored
commit ca4463bf upstream. The VT_DISALLOCATE ioctl can free a virtual console while tty_release() is still running, causing a use-after-free in con_shutdown(). This occurs because VT_DISALLOCATE considers a virtual console's 'struct vc_data' to be unused as soon as the corresponding tty's refcount hits 0. But actually it may be still being closed. Fix this by making vc_data be reference-counted via the embedded 'struct tty_port'. A newly allocated virtual console has refcount 1. Opening it for the first time increments the refcount to 2. Closing it for the last time decrements the refcount (in tty_operations::cleanup() so that it happens late enough), as does VT_DISALLOCATE. Reproducer: #include <fcntl.h> #include <linux/vt.h> #include <sys/ioctl.h> #include <unistd.h> int main() { if (fork()) { for (;;) close(open("/dev/tty5", O_RDWR)); } else { int fd = open("/dev/tty10", O_RDWR); for (;;) ioctl(fd, VT_DISALLOCATE, 5); } } KASAN report: BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278 Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129 CPU: 0 PID: 129 Comm: syz_vt Not tainted 5.6.0-rc2 #11 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014 Call Trace: [...] con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278 release_tty+0xa8/0x410 drivers/tty/tty_io.c:1514 tty_release_struct+0x34/0x50 drivers/tty/tty_io.c:1629 tty_release+0x984/0xed0 drivers/tty/tty_io.c:1789 [...] Allocated by task 129: [...] kzalloc include/linux/slab.h:669 [inline] vc_allocate drivers/tty/vt/vt.c:1085 [inline] vc_allocate+0x1ac/0x680 drivers/tty/vt/vt.c:1066 con_install+0x4d/0x3f0 drivers/tty/vt/vt.c:3229 tty_driver_install_tty drivers/tty/tty_io.c:1228 [inline] tty_init_dev+0x94/0x350 drivers/tty/tty_io.c:1341 tty_open_by_driver drivers/tty/tty_io.c:1987 [inline] tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035 [...] Freed by task 130: [...] kfree+0xbf/0x1e0 mm/slab.c:3757 vt_disallocate drivers/tty/vt/vt_ioctl.c:300 [inline] vt_ioctl+0x16dc/0x1e30 drivers/tty/vt/vt_ioctl.c:818 tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660 [...] Fixes: 4001d7b7 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com Acked-by:
-
Eric Biggers authored
commit 1aa6e058 upstream. The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are unnecessary because they can only be reached by calling ioctl() on an open tty, which implies the corresponding virtual console is allocated. And even if the virtual console *could* be freed concurrently, then these checks would be broken since they aren't done under console_lock, and the vc_data is dereferenced before them anyway. So, remove these unneeded checks to avoid confusion. Signed-off-by:
-
Jiri Slaby authored
commit f400991b upstream. vt_dont_switch is pure boolean, no need for whole char. Signed-off-by:
-
Jiri Slaby authored
commit e587e8f1 upstream. These two were macros. Switch them to static inlines, so that it's more understandable what they are doing. Signed-off-by:
-
Jiri Slaby authored
commit dce05aa6 upstream. Avoid global variables (namely sel_cons) by introducing vc_is_sel. It checks whether the parameter is the current selection console. This will help putting sel_cons to a struct later. Signed-off-by:
-
Johannes Berg authored
commit be8c827f upstream. The original patch didn't copy the ieee80211_is_data() condition because on most drivers the management frames don't go through this path. However, they do on iwlwifi/mvm, so we do need to keep the condition here. Cc: stable@vger.kernel.org Fixes: ce2e1ca7 ("mac80211: Check port authorization in the ieee80211_tx_dequeue() case") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Jouni Malinen authored
commit ce2e1ca7 upstream. mac80211 used to check port authorization in the Data frame enqueue case when going through start_xmit(). However, that authorization status may change while the frame is waiting in a queue. Add a similar check in the dequeue case to avoid sending previously accepted frames after authorization change. This provides additional protection against potential leaking of frames after a station has been disconnected and the keys for it are being removed. Cc: stable@vger.kernel.org Signed-off-by:
Jouni Malinen <jouni@codeaurora.org> Link: https://lore.kernel.org/r/20200326155133.ced84317ea29.I34d4c47cd8cc8a4042b38a76f16a601fbcbfd9b3@changeidSigned-off-by:
-
Johan Hovold authored
commit a246b4d5 upstream. Make sure to check that we have two alternate settings and at least one endpoint before accessing the second altsetting structure and dereferencing the endpoint arrays. This specifically avoids dereferencing NULL-pointers or corrupting memory when a device does not have the expected descriptors. Note that the sanity check in cit_get_packet_size() is not redundant as the driver is mixing looking up altsettings by index and by number, which may not coincide. Fixes: 659fefa0 ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01") Fixes: 59f8b0bf ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting") Cc: stable <stable@vger.kernel.org> # 2.6.37 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 485b06aa upstream. Make sure to check that we have two alternate settings and at least one endpoint before accessing the second altsetting structure and dereferencing the endpoint arrays. This specifically avoids dereferencing NULL-pointers or corrupting memory when a device does not have the expected descriptors. Note that the sanity checks in stv06xx_start() and pb0100_start() are not redundant as the driver is mixing looking up altsettings by index and by number, which may not coincide. Fixes: 8668d504 ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor") Fixes: c0b33bdc ("[media] gspca-stv06xx: support bandwidth changing") Cc: stable <stable@vger.kernel.org> # 2.6.31 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Johan Hovold authored
commit f5298101 upstream. Make sure to use the current alternate setting when verifying the interface descriptors to avoid submitting an URB to an invalid endpoint. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: c4018fa2 ("[media] dib0700: fix RC support on Hauppauge Nova-TD") Cc: stable <stable@vger.kernel.org> # 3.16 Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Johan Hovold authored
commit 99891234 upstream. Make sure to check that we have at least one endpoint before accessing the endpoint array to avoid dereferencing a NULL-pointer on stream start. Note that these sanity checks are not redundant as the driver is mixing looking up altsettings by index and by number, which need not coincide. Fixes: 1876bb92 ("V4L/DVB (12079): gspca_ov519: add support for the ov511 bridge") Fixes: b282d873 ("V4L/DVB (12080): gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)") Cc: stable <stable@vger.kernel.org> # 2.6.31 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Eric Biggers authored
commit a65cab7d upstream. Reading from a debugfs file at a nonzero position, without first reading at position 0, leaks uninitialized memory to userspace. It's a bit tricky to do this, since lseek() and pread() aren't allowed on these files, and write() doesn't update the position on them. But writing to them with splice() *does* update the position: #define _GNU_SOURCE 1 #include <fcntl.h> #include <stdio.h> #include <unistd.h> int main() { int pipes[2], fd, n, i; char buf[32]; pipe(pipes); write(pipes[1], "0", 1); fd = open("/sys/kernel/debug/fault_around_bytes", O_RDWR); splice(pipes[0], NULL, fd, NULL, 1, 0); n = read(fd, buf, sizeof(buf)); for (i = 0; i < n; i++) printf("%02x", buf[i]); printf("\n"); } Output: 5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a5a30 Fix the infoleak by making simple_attr_read() always fill simple_attr::get_buf if it hasn't been filled yet. Reported-by: syzbot+fcab69d1ada3e8d6f06b@syzkaller.appspotmail.com Reported-by:
Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20200308023849.988264-1-ebiggers@kernel.orgSigned-off-by:
-
Kai-Heng Feng authored
commit 32d25454 upstream. Add the PCI ID to the driver list to support this new device. Cc: stable@vger.kernel.org Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Qiujun Huang authored
commit 1165dd73 upstream. We can't handle the case length > WLAN_DATA_MAXLEN. Because the size of rxfrm->data is WLAN_DATA_MAXLEN(2312), and we can't read more than that. Thanks-to: Hillf Danton <hdanton@sina.com> Reported-and-tested-by: syzbot+7d42d68643a35f71ac8a@syzkaller.appspotmail.com Signed-off-by:
Qiujun Huang <hqjagain@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200326131850.17711-1-hqjagain@gmail.comSigned-off-by:
-
Qiujun Huang authored
commit a1f165a6 upstream. We should cancel hw->usb_work before kfree(hw). Reported-by: syzbot+6d2e7f6fa90e27be9d62@syzkaller.appspotmail.com Signed-off-by:
-
Larry Finger authored
commit 38ef48f7 upstream. The ASUS USB-N10 Nano B1 has been reported as a new RTL8188EU device. Add it to the device tables. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Reported-by:
kovi <zraetn@gmail.com> Cc: Stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200321180011.26153-1-Larry.Finger@lwfinger.netSigned-off-by:
-
Johan Hovold authored
commit 536f561d upstream. The driver was issuing synchronous uninterruptible control requests without using a timeout. This could lead to the driver hanging on various user requests due to a malfunctioning (or malicious) device until the device is physically disconnected. The USB upper limit of five seconds per request should be more than enough. Fixes: f3d27f34 ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber") Fixes: c53a846c ("[media] usbtv: add video controls") Cc: stable <stable@vger.kernel.org> # 3.11 Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Reviewed-by:
-
Johan Hovold authored
commit bca243b1 upstream. commit 1b976fc6 ("media: b2c2-flexcop-usb: add sanity checking") added an endpoint sanity check to address a NULL-pointer dereference on probe. Unfortunately the check was done on the current altsetting which was later changed. Fix this by moving the sanity check to after the altsetting is changed. Fixes: 1b976fc6 ("media: b2c2-flexcop-usb: add sanity checking") Cc: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Mans Rullgard authored
commit 52974d94 upstream. When handling a PIO bulk transfer with highmem buffer, a temporary mapping is assigned to urb->transfer_buffer. After the transfer is complete, an invalid address is left behind in this pointer. This is not ordinarily a problem since nothing touches that buffer before the urb is released. However, when usbmon is active, usbmon_urb_complete() calls (indirectly) mon_bin_get_data() which does access the transfer buffer if it is set. To prevent an invalid memory access here, reset urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not set it at all (musb_host_tx()). Fixes: 8e8a5516 ("usb: musb: host: Handle highmem in PIO mode") Signed-off-by:
Mans Rullgard <mans@mansr.com> Cc: stable@vger.kernel.org Signed-off-by:
Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.comSigned-off-by:
-
Qiujun Huang authored
commit 57aa9f29 upstream. Fix slab-out-of-bounds read in the interrupt-URB completion handler. The boundary condition should be (length - 1) as we access data[position + 1]. Reported-and-tested-by: syzbot+37ba33391ad5f3935bbd@syzkaller.appspotmail.com Signed-off-by:
-
Matthias Reichl authored
commit 62d65bdd upstream. commit b401f8c4 ("USB: cdc-acm: fix rounding error in TIOCSSERIAL") introduced a regression by changing the order of capability and close settings change checks. When running with CAP_SYS_ADMIN setting the close settings to the values already set resulted in -EOPNOTSUPP. Fix this by changing the check order back to how it was before. Fixes: b401f8c4 ("USB: cdc-acm: fix rounding error in TIOCSSERIAL") Cc: Anthony Mallet <anthony.mallet@laas.fr> Cc: stable <stable@vger.kernel.org> Cc: Oliver Neukum <oneukum@suse.com> Signed-off-by:
Matthias Reichl <hias@horus.com> Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.comSigned-off-by:
-
Pawel Dembicki authored
commit dfee7e2f upstream. This modem is embedded on dlink dwr-960 router. The oem configuration states: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1435 ProdID=d191 Rev=ff.ff S: Manufacturer=Android S: Product=Android S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Tested on openwrt distribution Signed-off-by:
Pawel Dembicki <paweldembicki@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Pawel Dembicki authored
commit 6cb2669c upstream. BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem. Tested hardware BM806U is mounted on D-Link DWR-921-C3 router. T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2033 Rev= 2.28 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=f842866cfd5a C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Co-developed-by:
Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by:
-
