Problem statement: 1) both paths (primary path1 and alternate
path2) are up after the association has been established i.e.,
HB packets are normally exchanged, 2) path2 gets inactive after
path_max_retrans * max_rto timed out (i.e. path2 is down completely),
3) now, if a transmission times out on the only surviving/active
path1 (any ~1sec network service impact could cause this like
a channel bonding failover), then the retransmitted packets are
sent over the inactive path2; this happens with partial failover
and without it.

Besides not being optimal in the above scenario, a small failure
or timeout in the only existing path has the potential to cause
long delays in the retransmission (depending on RTO_MAX) until
the still active path is reselected. Further, when the T3-timeout
occurs, we have active_patch == retrans_path, and even though the
timeout occurred on the initial transmission of data, not a
retransmit, we end up updating retransmit path.

RFC4960, section 6.4. "Multi-Homed SCTP Endpoints" states under
6.4.1. "Failover from an Inactive Destination Address" the
following:

  Some of the transport addresses of a multi-homed SCTP endpoint
  may become inactive due to either the occurrence of certain
  error conditions (see Section 8.2) or adjustments from the
  SCTP user.

  When there is outbound data to send and the primary path
  becomes inactive (e.g., due to failures), or where the SCTP
  user explicitly requests to send data to an inactive
  destination transport address, before reporting an error to
  its ULP, the SCTP endpoint should try to send the data to an
  alternate __active__ destination transport address if one
  exists.

  When retransmitting data that timed out, if the endpoint is
  multihomed, it should consider each source-destination address
  pair in its retransmission selection policy. When retransmitting
  timed-out data, the endpoint should attempt to pick the most
  divergent source-destination pair from the original
  source-destination pair to which the packet was transmitted.

  Note: Rules for picking the most divergent source-destination
  pair are an implementation decision and are not specified
  within this document.

So, we should first reconsider to take the current active
retransmission transport if we cannot find an alternative
active one. If all of that fails, we can still round robin
through unkown, partial failover, and inactive ones in the
hope to find something still suitable.

Commit 4141ddc0 ("sctp: retran_path update bug fix") broke
that behaviour by selecting the next inactive transport when
no other active transport was found besides the current assoc's
peer.retran_path. Before commit 4141ddc0, we would have
traversed through the list until we reach our peer.retran_path
again, and in case that is still in state SCTP_ACTIVE, we would
take it and return. Only if that is not the case either, we
take the next inactive transport.

Besides all that, another issue is that transports in state
SCTP_UNKNOWN could be preferred over transports in state
SCTP_ACTIVE in case a SCTP_ACTIVE transport appears after
SCTP_UNKNOWN in the transport list yielding a weaker transport
state to be used in retransmission.

This patch mostly reverts 4141ddc0, but also rewrites
this function to introduce more clarity and strictness into
the code. A strict priority of transport states is enforced
in this patch, hence selection is active > unkown > partial
failover > inactive.

Fixes: 4141ddc0 ("sctp: retran_path update bug fix")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Acked-by: Vlad Yasevich <yasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes bug introduced by:
commit 1d4c8c29
"neigh: restore old behaviour of default parms values"

The thing is that in neigh_sysctl_register, extra1 and extra2 which were
previously set for NEIGH_VAR_GC_* are overwritten. That leads to
nonsense int limits for gc_* variables. So fix this by not touching
extra* fields for gc_* variables.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes two bugs in fastopen :

1) The tcp_sendmsg(...,  @size) argument was ignored.

   Code was relying on user not fooling the kernel with iovec mismatches

2) When MTU is about 64KB, tcp_send_syn_data() attempts order-5
allocations, which are likely to fail when memory gets fragmented.

Fixes: 783237e8 ("net-tcp: Fast Open client - sending SYN-data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Tested-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ying Xue says:

====================
tipc: clean up components initialization code

In this series, we will fix a regression issue involved by commit
6e967adf(tipc: relocate common functions from media to bearer)
But before the issue is fixed, we firstly adjust the process of
components initialization so as to remove all enabled flags from
necessary tipc components. Otherwise, without the change, we also
have to add an extra enabled flag into bearer layer indicating
whether bearer setup is finshed or not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Accidentally a side effect is involved by commit 6e967adf(tipc:
relocate common functions from media to bearer). Now tipc stack
handler of receiving packets from netdevices as well as netdevice
notification handler are registered when bearer is enabled rather
than tipc module initialization stage, but the two handlers are
both unregistered in tipc module exit phase. If tipc module is
inserted and then immediately removed, the following warning
message will appear:

"dev_remove_pack: ffffffffa0380940 not found"

This is because in module insertion stage tipc stack packet handler
is not registered at all, but in module exit phase dev_remove_pack()
needs to remove it. Of course, dev_remove_pack() cannot find tipc
protocol handler from the kernel protocol handler list so that the
warning message is printed out.

But if registering the two handlers is adjusted from enabling bearer
phase into inserting module stage, the warning message will be
eliminated. Due to this change, tipc_core_start_net() and
tipc_core_stop_net() can be deleted as well.
Reported-by: Wang Weidong <wangweidong1@huawei.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tipc module is inserted, many tipc components are initialized
one by one. During the initialization period, if one of them is
failed, tipc_core_stop() will be called to stop all components
whatever corresponding components are created or not. To avoid to
release uncreated ones, relevant components have to add necessary
enabled flags indicating whether they are created or not.

But in the initialization stage, if one component is unsuccessfully
created, we will just destroy successfully created components before
the failed component instead of all components. All enabled flags
defined in components, in turn, become redundant. Additionally it's
also unnecessary to identify whether table.types is NULL in
tipc_nametbl_stop() because name stable has been definitely created
successfully when tipc_nametbl_stop() is called.

Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In current implementation it is possible to reach PF state from unconfirmed.
We can interpret sctp-failover-02 in a way that PF state is meant to be reached
only from active state, in the end, this is when entering PF state makes sense.
Here are few quotes from sctp-failover-02, but regardless of these, same
understanding can be reached from whole section 5:

Section 5.1, quickfailover guide:
    "The PF state is an intermediate state between Active and Failed states."

    "Each time the T3-rtx timer expires on an active or idle
    destination, the error counter of that destination address will
    be incremented.  When the value in the error counter exceeds
    PFMR, the endpoint should mark the destination transport address as PF."

There are several concrete reasons for such interpretation. For start, rfc4960
does not take into concern quickfailover algorithm. Therefore, quickfailover
must comply to 4960. Point where this compliance can be argued is following
behavior:
When PF is entered, association overall error counter is incremented for each
missed HB. This is contradictory to rfc4960, as address, while in unconfirmed
state, is subjected to probing, and while it is probed, it should not increment
association overall error counter. This has as a consequence that we might end
up in situation in which we drop association due path failure on unconfirmed
address, in case we have wrong configuration in a way:
Association.Max.Retrans == Path.Max.Retrans.

Another reason is that entering PF from unconfirmed will cause a loss of address
confirmed event when address is once (if) confirmed. This is fine from failover
guide point of view, but it is not consistent with behavior preceding failover
implementation and recommendation from 4960:

5.4.  Path Verification
   Whenever a path is confirmed, an indication MAY be given to the upper
   layer.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to
enable tx interrupt generation and crc checksum.

There has potential issue like as:
CPU			fec uDMA
Set tx ready bit
			uDMA start the BD transmission
Set "INT" bit
Set "PINS" bit
...

Above situation cause fec tx interrupt lost and fec MAC don't do
CRC checksum. The patch fix the potential issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug introduced by commit 7d442fab ("ipv4: Cache dst in tunnels").

Because sit code does not call ip_tunnel_init(), the dst_cache was not
initialized.

CC: Tom Herbert <therbert@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though only the outer vlan tag can be HW accelerated in the transmission
path, in the TUN/TAP driver vlan_features mirrors hw_features, which happens
to have the NETIF_F_HW_VLAN_?TAG_TX flags set. Because of this, during packet
tranmisssion through a stacked vlan device dev_hard_start_xmit, (incorrectly)
assuming that the vlan device supports hardware vlan acceleration, does not
add the vlan header to the skb payload and the inner vlan tags are lost
(vlan_tci contains the outer vlan tag when userspace reads the packet from
the tap device).
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even if we create a stacked vlan interface such as veth0.10.20, it sends
single tagged frames (tagged with only vid 10).
Because vlan_features of a veth interface has the
NETIF_F_HW_VLAN_[CTAG/STAG]_TX bits, veth0.10 also has that feature, so
dev_hard_start_xmit(veth0.10) doesn't call __vlan_put_tag() and
vlan_dev_hard_start_xmit(veth0.10) overwrites vlan_tci.
This prevents us from using a combination of 802.1ad and 802.1Q
in containers, etc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/built-in.o:(.rodata+0x1707c): undefined reference to `ip_tunnel_get_stats64'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ed1f50c3 ("net: add skb_checksum_setup") we introduced some checksum
functions in core driver. Subsequent change b5cf66cd ("xen-netfront:
use new skb_checksum_setup function") made use of those functions to
replace its own implementation.

However with that change netfront is broken. It sees a lot of checksum
error. That's because its own implementation of checksum function was a
bit hacky (dereferencing skb->data directly) while the new function was
implemented using ip_hdr(). The network header is not reset before skb
is passed to the new function. When the new function tries to do its
job, it's confused and reports error.

The fix is simple, we need to reset network header before passing skb to
checksum function. Netback is not affected as it already does the right
thing.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

* Fix nf_trace in nftables if XT_TRACE=n, from Florian Westphal.

* Don't use the fast payload operation in nf_tables if the length is
  not power of 2 or it is not aligned, from Nikolay Aleksandrov.

* Fix missing break statement the inet flavour of nft_reject, which
  results in evaluating IPv4 packets with the IPv6 evaluation routine,
  from Patrick McHardy.

* Fix wrong kconfig symbol in nft_meta to match the routing realm,
  from Paul Bolle.

* Allocate the NAT null binding when creating new conntracks via
  ctnetlink to avoid that several packets race at initializing the
  the conntrack NAT extension, original patch from Florian Westphal,
  revisited version from me.

* Fix DNAT handling in the snmp NAT helper, the same handling was being
  done for SNAT and DNAT and 2.4 already contains that fix, from
  Francois-Xavier Le Bail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes from Dave Airlie:
 "Lots of little small things, nothing too major: nouveau regression
  fixes, vmware fixes for the new hw support, memory leaks in error path
  fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
  drm/radeon/ni: fix typo in dpm sq ramping setup
  drm/radeon/si: fix typo in dpm sq ramping setup
  drm/radeon: fix CP semaphores on CIK
  drm/radeon: delete a stray tab
  drm/radeon: fix display tiling setup on SI
  drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
  drm/radeon: fill in DRM_CAPs for cursor size
  drm: add DRM_CAPs for cursor size
  drm/radeon: unify bpc handling
  drm/ttm: Fix memory leak in ttm_agp_backend.c
  drm/ttm: declare 'struct device' in ttm_page_alloc.h
  drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
  drm/nv50/disp: use correct register to determine DP display bpp
  drm/nouveau/fb: use correct ram oclass for nv1a hardware
  drm/nv50/gr: add missing nv_error parameter priv
  drm/nouveau: fix ENG_RUNLIST register address
  drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
  drm/nv4c/vga: decode register is in a different place on nv4x igp's
  drm/nv4c/mc: nv4x igp's have a different msi rearm register
  drm/nouveau: set irq_enabled manually
  ...

Pull HID update from Jiri Kosina:

 - fixes for several bugs in incorrect allocations of buffers by David
   Herrmann and Benjamin Tissoires.

 - support for a few new device IDs by Archana Patni, Benjamin
   Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hyperv: make sure input buffer is big enough
  HID: Bluetooth: hidp: make sure input buffers are big enough
  HID: hid-sensor-hub: quirk for STM Sensor hub
  HID: apple: add Apple wireless keyboard 2011 JIS model support
  HID: fix buffer allocations
  HID: multitouch: add FocalTech FTxxxx support
  HID: microsoft: Add ID's for Surface Type/Touch Cover 2
  HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay

Pull networking fixes from David Miller:

 1) kvaser CAN driver has fixed limits of some of it's table, validate
    that we won't exceed those limits at probe time.  Fix from Olivier
    Sobrie.

 2) Fix rtl8192ce disabling interrupts for too long, from Olivier
    Langlois.

 3) Fix botched shift in ath5k driver, from Dan Carpenter.

 4) Fix corruption of deferred packets in TIPC, from Erik Hugne.

 5) Fix newlink error path in macvlan driver, from Cong Wang.

 6) Fix netpoll deadlock in bonding, from Ding Tianhong.

 7) Handle GSO packets properly in forwarding path when fragmentation is
    necessary on egress, from Florian Westphal.

 8) Fix axienet build errors, from Michal Simek.

 9) Fix refcounting of ubufs on tx in vhost net driver, from Michael S
    Tsirkin.

10) Carrier status isn't set properly in hyperv driver, from Haiyang
    Zhang.

11) Missing pci_disable_device() in tulip_remove_one), from Ingo Molnar.

12) AF_PACKET qdisc bypass mode doesn't adhere to driver provided TX
    queue selection method.  Add a fallback method mechanism to fix this
    bug, from Daniel Borkmann.

13) Fix regression in link local route handling on GRE tunnels, from
    Nicolas Dichtel.

14) Bonding can assign dup aggregator IDs in some sequences of
    configuration, fix by making the allocation counter per-bond instead
    of global.  From Jiri Bohac.

15) sctp_connectx() needs compat translations, from Daniel Borkmann.

16) Fix of_mdio PHY interrupt parsing, from Ben Dooks

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  MAINTAINERS: add entry for the PHY library
  of_mdio: fix phy interrupt passing
  net: ethernet: update dependency and help text of mvneta
  NET: fec: only enable napi if we are successful
  af_packet: remove a stray tab in packet_set_ring()
  net: sctp: fix sctp_connectx abi for ia32 emulation/compat mode
  ipv4: fix counter in_slow_tot
  irtty-sir.c: Do not set_termios() on irtty_close()
  bonding: 802.3ad: make aggregator_identifier bond-private
  usbnet: remove generic hard_header_len check
  gre: add link local route when local addr is any
  batman-adv: fix potential kernel paging error for unicast transmissions
  batman-adv: avoid double free when orig_node initialization fails
  batman-adv: free skb on TVLV parsing success
  batman-adv: fix TT CRC computation by ensuring byte order
  batman-adv: fix potential orig_node reference leak
  batman-adv: avoid potential race condition when adding a new neighbour
  batman-adv: properly check pskb_may_pull return value
  batman-adv: release vlan object after checking the CRC
  batman-adv: fix TT-TVLV parsing on OGM reception
  ...

Pull ARM fixes from Russell King:
 "A range of ARM fixes.  Biggest change is the stage-2 attributes used
  for for hyp mode which were wrong.  I've killed some bits in a couple
  of DT files which turned out not to be required, and a few other
  fixes.

  One fix touches code outside of arch/arm, which is related to sorting
  out the DMA masks correctly.  There is a long standing issue with the
  conversion from PFNs to addresses where people assume that shifting an
  unsigned long left by PAGE_SHIFT results in a correct address.  This
  is not the case with C: the integer promotion happens at assignment
  after evaluation.  This fixes the recently introduced dma_max_pfn()
  function, but there's a number of other places where we try this
  directly on an unsigned long in the mm code"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
  Fix uses of dma_max_pfn() when converting to a limiting address
  ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
  ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
  ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
  ARM: 7950/1: mm: Fix stage-2 device memory attributes
  ARM: dts: fix spdif pinmux configuration

Pull jfs fix from David Kleikamp:
 "Another ACL regression. This one more subtle"

* tag 'jfs-3.14-rc4' of git://github.com/kleikamp/linux-shaggy:
  jfs: set i_ctime when setting ACL

The PHY library has been subject to some changes, new drivers and DT
interactions over the past few months. Add myself as a maintainer for
the core PHY library parts and drivers. Make sure the PHY library entry
also covers the Device Tree files which have a close interaction with
the MDIO bus, PHY connection and Ethernet PHY mode parsing.

CC: Grant Likely <grant.likely@linaro.org>
CC: Shaohui Xie <shaohui.xie@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The of_mdiobus_register_phy() is not setting phy->irq thus causing
some drivers to incorrectly assume that the PHY does not have an
IRQ associated with it. Not only do some drivers report no IRQ
they do not install an interrupt handler for the PHY.

Simplify the code setting irq and set the phy->irq at the same
time so that we cover the following issues, which should cover
all the cases the code will find:

- Set phy->irq if node has irq property and mdio->irq is NULL
- Set phy->irq if node has no irq and mdio->irq is not NULL
- Leave phy->irq as PHY_POLL default if none of the above

This fixes the issue:
 net eth0: attached PHY 1 (IRQ -1) to driver Micrel KSZ8041RNLI

to the correct:
 net eth0: attached PHY 1 (IRQ 416) to driver Micrel KSZ8041RNLI
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.

In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

If napi is left enabled after a failed attempt to bring the interface
up, we BUG:

fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc

Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

At first glance it looks like there is a missing curly brace but
actually the code works the same either way.  I have adjusted the
indenting but left the code the same.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull request of 2014-02-18

One compile fix and one memory leak.

* tag 'ttm-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
  drm/ttm: Fix memory leak in ttm_agp_backend.c
  drm/ttm: declare 'struct device' in ttm_page_alloc.h

Merge tag 'vmwgfx-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux into drm-fixes

Pull request of 2014-02-18.

Nothing special. The biggest change is adding a couple of command defines and
packing the command data correctly.

* tag 'vmwgfx-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: Fix command defines and checks
  drm/vmwgfx: Fix possible integer overflow
  drm/vmwgfx: Remove stray const
  drm/vmwgfx: unlock on error path in vmw_execbuf_process()
  drm/vmwgfx: Get maximum mob size from register SVGA_REG_MOB_MAX_SIZE
  drm/vmwgfx: Fix a couple of sparse warnings and errors

Fix for 128x128 cursors, along with some misc fixes.

* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon/ni: fix typo in dpm sq ramping setup
  drm/radeon/si: fix typo in dpm sq ramping setup
  drm/radeon: fix CP semaphores on CIK
  drm/radeon: delete a stray tab
  drm/radeon: fix display tiling setup on SI
  drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
  drm/radeon: fill in DRM_CAPs for cursor size
  drm: add DRM_CAPs for cursor size
  drm/radeon: unify bpc handling

John W. Linville says:

====================
Please pull this batch of fixes intended for the 3.14 stream...

For the iwlwifi one, Emmanuel says:

"As explicitly written in the commit message, we prefer to disable Tx
AMPDU on NICs supported by iwldvm. This feature gives a big boost in
Tx performance, but the firmware is buggy and we can't rely on it.
Our hope is that most of the users out there want wifi to surf on
the web which means that they care more for Rx traffic than for Tx.
People who want to enable it can do so with the help of a module
parameter."

On top of that...

Dan Carpenter fixes a typo/thinko in ath5k.

Olivier Langlois fixes a couple of rtlwifi issues, one which leaves
IRQs disabled too long (causing a variety of problems elsewhere),
and one which fixes an incorrect return code when failing to enable
the NIC.

Russell King fixes a NULL pointer dereference in hostap.

Stanislaw Gruszka fixes a DMA coherence issue in the rtl8187 driver.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP's sctp_connectx() abi breaks for 64bit kernels compiled with 32bit
emulation (e.g. ia32 emulation or x86_x32). Due to internal usage of
'struct sctp_getaddrs_old' which includes a struct sockaddr pointer,
sizeof(param) check will always fail in kernel as the structure in
64bit kernel space is 4bytes larger than for user binaries compiled
in 32bit mode. Thus, applications making use of sctp_connectx() won't
be able to run under such circumstances.

Introduce a compat interface in the kernel to deal with such
situations by using a 'struct compat_sctp_getaddrs_old' structure
where user data is copied into it, and then sucessively transformed
into a 'struct sctp_getaddrs_old' structure with the help of
compat_ptr(). That fixes sctp_connectx() abi without any changes
needed in user space, and lets the SCTP test suite pass when compiled
in 32bit and run on 64bit kernels.

Fixes: f9c67811 ("sctp: Fix regression introduced by new sctp_connectx api")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes:
- fix soft-interface MTU computation
- fix bogus pointer mangling when parsing the TT-TVLV
  container. This bug led to a wrong memory access.
- fix memory leak by properly releasing the VLAN object
  after CRC check
- properly check pskb_may_pull() return value
- avoid potential race condition while adding new neighbour
- fix potential memory leak by removing all the references
  to the orig_node object in case of initialization failure
- fix the TT CRC computation by ensuring that every node uses
  the same byte order when hosts with different endianess are
  part of the same network
- fix severe memory leak by freeing skb after a successful
  TVLV parsing
- avoid potential double free when orig_node initialization
  fails
- fix potential kernel paging error caused by the usage of
  the old value of skb->data after skb reallocation
Signed-off-by: David S. Miller <davem@davemloft.net>

inverted logic.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

inverted logic.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The CP semaphore queue on CIK has a bug that triggers if uncompleted
waits use the same address while a signal is still pending. Work around
this by using different addresses for each sync.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Static checkers complain that probably curly braces were intended here,
but actually it makes more sense to remove the extra tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Apply the same logic as CI to SI for setting up the
display tiling parameters.  The num banks may vary
per tiling index just like CI.

Bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=71488
https://bugs.freedesktop.org/show_bug.cgi?id=73946
https://bugs.freedesktop.org/show_bug.cgi?id=74927Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Most laptops seems to have a vblank period of less than
300 and mclk switching works fine.  Drop the quirk and
set the default threshold to 200.

bug:
https://bugzilla.kernel.org/show_bug.cgi?id=70701Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

CIK parts are 128x128, older parts are 64x64.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Some hardware may not support standard 64x64 cursors.  Add
a drm cap to query the cursor size from the kernel.  Some examples
include radeon CIK parts (128x128 cursors) and armada (32x64 or 64x32).
This allows things like device specific ddxes to remove asics specific
logic and also allows xf86-video-modesetting to work properly with hw
cursors on this hardware. Default to 64 if the driver doesn't specify
a size.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>

We were already storing the bpc (bits per color) information
in radeon_crtc, so just use that everywhere rather than
calculating it everywhere we use it.  This also allows us
to change it in one place if we ever want to override it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>