Commits · 4e0effd9007ea0be31f7488611eb3824b4541554 · Kirill Smelkov / linux

23 Jun, 2022 4 commits

igb: Make DMA faster when CPU is active on the PCIe link · 4e0effd9

Kai-Heng Feng authored Jun 21, 2022

Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.

According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.

In addition to that, commit b6e0c419 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.

Fixes: b6e0c419 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

4e0effd9

net: dsa: qca8k: reduce mgmt ethernet timeout · 85467f7d

Christian Marangi authored Jun 21, 2022

The current mgmt ethernet timeout is set to 100ms. This value is too
big and would slow down any mdio command in case the mgmt ethernet
packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the
master port that would cause the mgmt ethernet to not work temporarily.

Fixes: 5950c7c0 ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

85467f7d

net: dsa: qca8k: reset cpu port on MTU change · 386228c6

Christian Marangi authored Jun 21, 2022

It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.

In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.

To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.

Fixes: f58d2598 ("net: dsa: qca8k: implement the port MTU callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

386228c6

MAINTAINERS: Add a maintainer for OCP Time Card · 13f28c2c

Vadim Fedorenko authored Jun 22, 2022

I've been contributing and reviewing patches for ptp_ocp driver for
some time and I'm taking care of it's github mirror. On Jakub's
suggestion, I would like to step forward and become a maintainer for
this driver. This patch adds a dedicated entry to MAINTAINERS.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220621233131.21240-1-vfedorenko@novek.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

13f28c2c

22 Jun, 2022 4 commits

hinic: Replace memcpy() with direct assignment · 1e70212e

Kees Cook authored Jun 15, 2022

Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged
here for calculating the size of the destination buffer (0x10 instead of
0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with
the source and dest being struct fw_section_info_st, so the memcpy should
be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's
responsibility to figure out.

Avoid the whole thing and just do a direct assignment. This results in
no change to the executable code.

[This is a duplicate of commit 2c0ab32b ("hinic: Replace memcpy()
 with direct assignment") which was applied to net-next.]

Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: llvm@lists.linux.dev
Link: https://github.com/ClangBuiltLinux/linux/issues/1592Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Link: https://lore.kernel.org/r/20220616052312.292861-1-keescook@chromium.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

1e70212e

Revert "drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c" · 877fe9d4

Jakub Kicinski authored Jun 20, 2022

This reverts commit 8fc74d18.

BAR0 is the main (only?) register bank for this device. We most
obviously can't unmap it before the netdev is unregistered.
This was pointed out in review but the patch got reposted and
merged, anyway.

The author of the patch was only testing it with a QEMU model,
which I presume does not emulate enough for the netdev to be brought
up (author's replies are not visible in lore because they kept sending
their emails in HTML).

Link: https://lore.kernel.org/all/20220616085059.680dc215@kernel.org/
Fixes: 8fc74d18 ("drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

877fe9d4

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf · 53664d51

Jakub Kicinski authored Jun 21, 2022

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Use get_random_u32() instead of prandom_u32_state() in nft_meta
   and nft_numgen, from Florian Westphal.

2) Incorrect list head in nfnetlink_cttimeout in recent update coming
   from previous development cycle. Also from Florian.

3) Incorrect path to pktgen scripts for nft_concat_range.sh selftest.
   From Jie2x Zhou.

4) Two fixes for the for nft_fwd and nft_dup egress support, from Florian.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: nf_dup_netdev: add and use recursion counter
  netfilter: nf_dup_netdev: do not push mac header a second time
  selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
  netfilter: cttimeout: fix slab-out-of-bounds read typo in cttimeout_net_exit
  netfilter: use get_random_u32 instead of prandom
====================

Link: https://lore.kernel.org/r/20220621085618.3975-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

53664d51

net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode · 2642cc6c

Lukas Wunner authored Jun 20, 2022

Simon reports that if two LAN9514 USB adapters are directly connected
without an intermediate switch, the link fails to come up and link LEDs
remain dark. The issue was introduced by commit 1ce8b372 ("usbnet:
smsc95xx: Forward PHY interrupts to PHY driver to avoid polling").

The PHY suffers from a known erratum wherein link detection becomes
unreliable if Energy Detect Power-Down is used. In poll mode, the
driver works around the erratum by briefly disabling EDPD for 640 msec
to detect a neighbor, then re-enabling it to save power.

In interrupt mode, no interrupt is signaled if EDPD is used by both link
partners, so it must not be enabled at all.

We'll recoup the power savings by enabling SUSPEND1 mode on affected
LAN95xx chips in a forthcoming commit.

Fixes: 1ce8b372 ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/439a3f3168c2f9d44b5fd9bb8d2b551711316be6.1655714438.git.lukas@wunner.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

2642cc6c

21 Jun, 2022 3 commits

netfilter: nf_dup_netdev: add and use recursion counter · fcd53c51

Florian Westphal authored Jun 20, 2022

Now that the egress function can be called from egress hook, we need
to avoid recursive calls into the nf_tables traverser, else crash.

Fixes: f87b9464 ("netfilter: nft_fwd_netdev: Support egress hook")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

fcd53c51

netfilter: nf_dup_netdev: do not push mac header a second time · 574a5b85

Florian Westphal authored Jun 20, 2022

Eric reports skb_under_panic when using dup/fwd via bond+egress hook.
Before pushing mac header, we should make sure that we're called from
ingress to put back what was pulled earlier.

In egress case, the MAC header is already there; we should leave skb
alone.

While at it be more careful here: skb might have been altered and
headroom reduced, so add a skb_cow() before so that headroom is
increased if necessary.

nf_do_netdev_egress() assumes skb ownership (it normally ends with
a call to dev_queue_xmit), so we must free the packet on error.

Fixes: f87b9464 ("netfilter: nft_fwd_netdev: Support egress hook")
Reported-by: Eric Garver <eric@garver.life>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

574a5b85

selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh · 5d79d8af

Jie2x Zhou authored Jun 16, 2022

Before change:
make -C netfilter
 TEST: performance
   net,port                                                      [SKIP]
   perf not supported
   port,net                                                      [SKIP]
   perf not supported
   net6,port                                                     [SKIP]
   perf not supported
   port,proto                                                    [SKIP]
   perf not supported
   net6,port,mac                                                 [SKIP]
   perf not supported
   net6,port,mac,proto                                           [SKIP]
   perf not supported
   net,mac                                                       [SKIP]
   perf not supported

After change:
   net,mac                                                       [ OK ]
     baseline (drop from netdev hook):               2061098pps
     baseline hash (non-ranged entries):             1606741pps
     baseline rbtree (match on first field only):    1191607pps
     set with  1000 full, ranged entries:            1639119pps
ok 8 selftests: netfilter: nft_concat_range.sh

Fixes: 611973c1 ("selftests: netfilter: Introduce tests for sets with range concatenation")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jie2x Zhou <jie2x.zhou@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

5d79d8af

20 Jun, 2022 3 commits

net/tls: fix tls_sk_proto_close executed repeatedly · 69135c57

Ziyang Xuan authored Jun 20, 2022

After setting the sock ktls, update ctx->sk_proto to sock->sk_prot by
tls_update(), so now ctx->sk_proto->close is tls_sk_proto_close(). When
close the sock, tls_sk_proto_close() is called for sock->sk_prot->close
is tls_sk_proto_close(). But ctx->sk_proto->close() will be executed later
in tls_sk_proto_close(). Thus tls_sk_proto_close() executed repeatedly
occurred. That will trigger the following bug.

=================================================================
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:tls_sk_proto_close+0xd8/0xaf0 net/tls/tls_main.c:306
Call Trace:
 <TASK>
 tls_sk_proto_close+0x356/0xaf0 net/tls/tls_main.c:329
 inet_release+0x12e/0x280 net/ipv4/af_inet.c:428
 __sock_release+0xcd/0x280 net/socket.c:650
 sock_close+0x18/0x20 net/socket.c:1365

Updating a proto which is same with sock->sk_prot is incorrect. Add proto
and sock->sk_prot equality check at the head of tls_update() to fix it.

Fixes: 95fa1454 ("bpf: sockmap/tls, close can race with map free")
Reported-by: syzbot+29c3c12f3214b85ad081@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

69135c57

erspan: do not assume transport header is always set · 301bd140

Eric Dumazet authored Jun 20, 2022

Rewrite tests in ip6erspan_tunnel_xmit() and
erspan_fb_xmit() to not assume transport header is set.

syzbot reported:

WARNING: CPU: 0 PID: 1350 at include/linux/skbuff.h:2911 skb_transport_header include/linux/skbuff.h:2911 [inline]
WARNING: CPU: 0 PID: 1350 at include/linux/skbuff.h:2911 ip6erspan_tunnel_xmit+0x15af/0x2eb0 net/ipv6/ip6_gre.c:963
Modules linked in:
CPU: 0 PID: 1350 Comm: aoe_tx0 Not tainted 5.19.0-rc2-syzkaller-00160-g274295c6 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
RIP: 0010:skb_transport_header include/linux/skbuff.h:2911 [inline]
RIP: 0010:ip6erspan_tunnel_xmit+0x15af/0x2eb0 net/ipv6/ip6_gre.c:963
Code: 0f 47 f0 40 88 b5 7f fe ff ff e8 8c 16 4b f9 89 de bf ff ff ff ff e8 a0 12 4b f9 66 83 fb ff 0f 85 1d f1 ff ff e8 71 16 4b f9 <0f> 0b e9 43 f0 ff ff e8 65 16 4b f9 48 8d 85 30 ff ff ff ba 60 00
RSP: 0018:ffffc90005daf910 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 000000000000ffff RCX: 0000000000000000
RDX: ffff88801f032100 RSI: ffffffff882e8d3f RDI: 0000000000000003
RBP: ffffc90005dafab8 R08: 0000000000000003 R09: 000000000000ffff
R10: 000000000000ffff R11: 0000000000000000 R12: ffff888024f21d40
R13: 000000000000a288 R14: 00000000000000b0 R15: ffff888025a2e000
FS: 0000000000000000(0000) GS:ffff88802c800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2e425000 CR3: 000000006d099000 CR4: 0000000000152ef0
Call Trace:
<TASK>
__netdev_start_xmit include/linux/netdevice.h:4805 [inline]
netdev_start_xmit include/linux/netdevice.h:4819 [inline]
xmit_one net/core/dev.c:3588 [inline]
dev_hard_start_xmit+0x188/0x880 net/core/dev.c:3604
sch_direct_xmit+0x19f/0xbe0 net/sched/sch_generic.c:342
__dev_xmit_skb net/core/dev.c:3815 [inline]
__dev_queue_xmit+0x14a1/0x3900 net/core/dev.c:4219
dev_queue_xmit include/linux/netdevice.h:2994 [inline]
tx+0x6a/0xc0 drivers/block/aoe/aoenet.c:63
kthread+0x1e7/0x3b0 drivers/block/aoe/aoecmd.c:1229
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:302
</TASK>

Fixes: d5db21a3 ("erspan: auto detect truncated ipv6 packets.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

301bd140

ipv4: fix bind address validity regression tests · 313c502f

Riccardo Paolo Bestetti authored Jun 19, 2022

Commit 8ff978b8 ("ipv4/raw: support binding to nonlocal addresses")
introduces support for binding to nonlocal addresses, as well as some
basic test coverage for some of the related cases.

Commit b4a028c4 ("ipv4: ping: fix bind address validity check")
fixes a regression which incorrectly removed some checks for bind
address validation. In addition, it introduces regression tests for
those specific checks. However, those regression tests are defective, in
that they perform the tests using an incorrect combination of bind
flags. As a result, those tests fail when they should succeed.

This commit introduces additional regression tests for nonlocal binding
and fixes the defective regression tests. It also introduces new
set_sysctl calls for the ipv4_bind test group, as to perform the ICMP
binding tests it is necessary to allow ICMP socket creation by setting
the net.ipv4.ping_group_range knob.

Fixes: b4a028c4 ("ipv4: ping: fix bind address validity check")
Reported-by: Riccardo Paolo Bestetti <pbl@bestov.io>
Signed-off-by: Riccardo Paolo Bestetti <pbl@bestov.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

313c502f

19 Jun, 2022 2 commits

net: phy: at803x: fix NULL pointer dereference on AR9331 PHY · 9926de73

Oleksij Rempel authored Jun 18, 2022

Latest kernel will explode on the PHY interrupt config, since it depends
now on allocated priv. So, run probe to allocate priv to fix it.

 ar9331_switch ethernet.1:10 lan0 (uninitialized): PHY [!ahb!ethernet@1a000000!mdio!switch@10:00] driver [Qualcomm Atheros AR9331 built-in PHY] (irq=13)
 CPU 0 Unable to handle kernel paging request at virtual address 0000000a, epc == 8050e8a8, ra == 80504b34
         ...
 Call Trace:
 [<8050e8a8>] at803x_config_intr+0x5c/0xd0
 [<80504b34>] phy_request_interrupt+0xa8/0xd0
 [<8050289c>] phylink_bringup_phy+0x2d8/0x3ac
 [<80502b68>] phylink_fwnode_phy_connect+0x118/0x130
 [<8074d8ec>] dsa_slave_create+0x270/0x420
 [<80743b04>] dsa_port_setup+0x12c/0x148
 [<8074580c>] dsa_register_switch+0xaf0/0xcc0
 [<80511344>] ar9331_sw_probe+0x370/0x388
 [<8050cb78>] mdio_probe+0x44/0x70
 [<804df300>] really_probe+0x200/0x424
 [<804df7b4>] __driver_probe_device+0x290/0x298
 [<804df810>] driver_probe_device+0x54/0xe4
 [<804dfd50>] __device_attach_driver+0xe4/0x130
 [<804dcb00>] bus_for_each_drv+0xb4/0xd8
 [<804dfac4>] __device_attach+0x104/0x1a4
 [<804ddd24>] bus_probe_device+0x48/0xc4
 [<804deb44>] deferred_probe_work_func+0xf0/0x10c
 [<800a0ffc>] process_one_work+0x314/0x4d4
 [<800a17fc>] worker_thread+0x2a4/0x354
 [<800a9a54>] kthread+0x134/0x13c
 [<8006306c>] ret_from_kernel_thread+0x14/0x1c

Same Issue would affect some other PHYs (QCA8081, QCA9561), so fix it
too.

Fixes: 3265f421 ("net: phy: at803x: add fiber support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

9926de73

drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c · 8fc74d18

Wentao_Liang authored Jun 19, 2022

The pointer vdev points to a memory region adjacent to a net_device
structure ndev, which is a field of hldev. At line 4740, the invocation
to vxge_device_unregister unregisters device hldev, and it also releases
the memory region pointed by vdev->bar0. At line 4743, the freed memory
region is referenced (i.e., iounmap(vdev->bar0)), resulting in a
use-after-free vulnerability. We can fix the bug by calling iounmap
before vxge_device_unregister.

4721.      static void vxge_remove(struct pci_dev *pdev)
4722.      {
4723.             struct __vxge_hw_device *hldev;
4724.             struct vxgedev *vdev;
…
4731.             vdev = netdev_priv(hldev->ndev);
…
4740.             vxge_device_unregister(hldev);
4741.             /* Do not call pci_disable_sriov here, as it
						will break child devices */
4742.             vxge_hw_device_terminate(hldev);
4743.             iounmap(vdev->bar0);
…
4749              vxge_debug_init(vdev->level_trace, "%s:%d
								Device unregistered",
4750                            __func__, __LINE__);
4751              vxge_debug_entryexit(vdev->level_trace, "%s:%d
								Exiting...", __func__,
4752                          __LINE__);
4753.      }

This is the screenshot when the vulnerability is triggered by using
KASAN. We can see that there is a use-after-free reported by KASAN.

/***************************start**************************/

root@kernel:~# echo 1 > /sys/bus/pci/devices/0000:00:03.0/remove
[  178.296316] vxge_remove
[  182.057081]
 ==================================================================
[  182.057548] BUG: KASAN: use-after-free in vxge_remove+0xe0/0x15c
[  182.057760] Read of size 8 at addr ffff888006c76598 by task bash/119
[  182.057983]
[  182.058747] CPU: 0 PID: 119 Comm: bash Not tainted 5.18.0 #5
[  182.058919] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[  182.059463] Call Trace:
[  182.059726]  <TASK>
[  182.060017]  dump_stack_lvl+0x34/0x44
[  182.060316]  print_report.cold+0xb2/0x6b7
[  182.060401]  ? kfree+0x89/0x290
[  182.060478]  ? vxge_remove+0xe0/0x15c
[  182.060545]  kasan_report+0xa9/0x120
[  182.060629]  ? vxge_remove+0xe0/0x15c
[  182.060706]  vxge_remove+0xe0/0x15c
[  182.060793]  pci_device_remove+0x5d/0xe0
[  182.060968]  device_release_driver_internal+0xf1/0x180
[  182.061063]  pci_stop_bus_device+0xae/0xe0
[  182.061150]  pci_stop_and_remove_bus_device_locked+0x11/0x20
[  182.061236]  remove_store+0xc6/0xe0
[  182.061297]  ? subordinate_bus_number_show+0xc0/0xc0
[  182.061359]  ? __mutex_lock_slowpath+0x10/0x10
[  182.061438]  ? sysfs_kf_write+0x6d/0xa0
[  182.061525]  kernfs_fop_write_iter+0x1b0/0x260
[  182.061610]  ? sysfs_kf_bin_read+0xf0/0xf0
[  182.061695]  new_sync_write+0x209/0x310
[  182.061789]  ? new_sync_read+0x310/0x310
[  182.061865]  ? cgroup_rstat_updated+0x5c/0x170
[  182.061937]  ? preempt_count_sub+0xf/0xb0
[  182.061995]  ? pick_next_entity+0x13a/0x220
[  182.062063]  ? __inode_security_revalidate+0x44/0x80
[  182.062155]  ? security_file_permission+0x46/0x2a0
[  182.062230]  vfs_write+0x33f/0x3e0
[  182.062303]  ksys_write+0xb4/0x150
[  182.062369]  ? __ia32_sys_read+0x40/0x40
[  182.062451]  do_syscall_64+0x3b/0x90
[  182.062531]  entry_SYSCALL_64_after_hwframe+0x46/0xb0
[  182.062894] RIP: 0033:0x7f3f37d17274
[  182.063558] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f
80 00 00 00 00 48 8d 05 89 54 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f
05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53
[  182.063797] RSP: 002b:00007ffd5ba9e178 EFLAGS: 00000246
ORIG_RAX: 0000000000000001
[  182.064117] RAX: ffffffffffffffda RBX: 0000000000000002
RCX: 00007f3f37d17274
[  182.064219] RDX: 0000000000000002 RSI: 000055bbec327180
RDI: 0000000000000001
[  182.064315] RBP: 000055bbec327180 R08: 000000000000000a
R09: 00007f3f37de7cf0
[  182.064414] R10: 000000000000000a R11: 0000000000000246
R12: 00007f3f37de8760
[  182.064513] R13: 0000000000000002 R14: 00007f3f37de3760
R15: 0000000000000002
[  182.064691]  </TASK>
[  182.064916]
[  182.065224] The buggy address belongs to the physical page:
[  182.065804] page:00000000ef31e4f4 refcount:0 mapcount:0
mapping:0000000000000000 index:0x0 pfn:0x6c76
[  182.067419] flags: 0x100000000000000(node=0|zone=1)
[  182.068997] raw: 0100000000000000 0000000000000000
ffffea00001b1d88 0000000000000000
[  182.069118] raw: 0000000000000000 0000000000000000
00000000ffffffff 0000000000000000
[  182.069294] page dumped because: kasan: bad access detected
[  182.069331]
[  182.069360] Memory state around the buggy address:
[  182.070006]  ffff888006c76480: ff ff ff ff ff ff ff ff ff ff ff
 ff ff ff ff ff
[  182.070136]  ffff888006c76500: ff ff ff ff ff ff ff ff ff ff ff
 ff ff ff ff ff
[  182.070230] >ffff888006c76580: ff ff ff ff ff ff ff ff ff ff ff
 ff ff ff ff ff
[  182.070305]                             ^
[  182.070456]  ffff888006c76600: ff ff ff ff ff ff ff ff ff ff ff
 ff ff ff ff ff
[  182.070505]  ffff888006c76680: ff ff ff ff ff ff ff ff ff ff ff
 ff ff ff ff ff
[  182.070606]
==================================================================
[  182.071374] Disabling lock debugging due to kernel taint

/*****************************end*****************************/

After fixing the bug as done in the patch, we can find KASAN do not report
 the bug and the device(00:03.0) has been successfully removed.

/*****************************start***************************/

root@kernel:~# echo 1 > /sys/bus/pci/devices/0000:00:03.0/remove
root@kernel:~#

/******************************end****************************/
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8fc74d18

18 Jun, 2022 5 commits

net/sched: sch_netem: Fix arithmetic in netem_dump() for 32-bit platforms · a2b1a5d4

Peilin Ye authored Jun 16, 2022

As reported by Yuming, currently tc always show a latency of UINT_MAX
for netem Qdisc's on 32-bit platforms:

    $ tc qdisc add dev dummy0 root netem latency 100ms
    $ tc qdisc show dev dummy0
    qdisc netem 8001: root refcnt 2 limit 1000 delay 275s  275s
                                               ^^^^^^^^^^^^^^^^

Let us take a closer look at netem_dump():

        qopt.latency = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->latency,
                             UINT_MAX);

qopt.latency is __u32, psched_tdiff_t is signed long,
(psched_tdiff_t)(UINT_MAX) is negative for 32-bit platforms, so
qopt.latency is always UINT_MAX.

Fix it by using psched_time_t (u64) instead.

Note: confusingly, users have two ways to specify 'latency':

  1. normally, via '__u32 latency' in struct tc_netem_qopt;
  2. via the TCA_NETEM_LATENCY64 attribute, which is s64.

For the second case, theoretically 'latency' could be negative.  This
patch ignores that corner case, since it is broken (i.e. assigning a
negative s64 to __u32) anyways, and should be handled separately.

Thanks Ted Lin for the analysis [1] .

[1] https://github.com/raspberrypi/linux/issues/3512Reported-by: Yuming Chen <chenyuming.junnan@bytedance.com>
Fixes: 112f9cb6 ("netem: convert to qdisc_watchdog_schedule_ns")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20220616234336.2443-1-yepeilin.cs@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

a2b1a5d4

ethtool: Fix get module eeprom fallback · a3bb7b63

Ivan Vecera authored Jun 16, 2022

Function fallback_set_params() checks if the module type returned
by a driver is ETH_MODULE_SFF_8079 and in this case it assumes
that buffer returns a concatenated content of page A0h and A2h.
The check is wrong because the correct type is ETH_MODULE_SFF_8472.

Fixes: 96d971e3 ("ethtool: Add fallback to get_module_eeprom from netlink command")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220616160856.3623273-1-ivecera@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

a3bb7b63

bonding: ARP monitor spams NETDEV_NOTIFY_PEERS notifiers · 7a9214f3

Jay Vosburgh authored Jun 16, 2022

The bonding ARP monitor fails to decrement send_peer_notif, the
number of peer notifications (gratuitous ARP or ND) to be sent. This
results in a continuous series of notifications.

Correct this by decrementing the counter for each notification.
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: b0929915 ("bonding: Fix RTNL: assertion failed at net/core/rtnetlink.c for ab arp monitor")
Link: https://lore.kernel.org/netdev/b2fd4147-8f50-bebd-963a-1a3e8d1d9715@redhat.com/Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/9400.1655407960@famineSigned-off-by: Jakub Kicinski <kuba@kernel.org>

7a9214f3

igb: fix a use-after-free issue in igb_clean_tx_ring · 3f6a57ee

Lorenzo Bianconi authored Jun 16, 2022

Fix the following use-after-free bug in igb_clean_tx_ring routine when
the NIC is running in XDP mode. The issue can be triggered redirecting
traffic into the igb NIC and then closing the device while the traffic
is flowing.

[   73.322719] CPU: 1 PID: 487 Comm: xdp_redirect Not tainted 5.18.3-apu2 #9
[   73.330639] Hardware name: PC Engines APU2/APU2, BIOS 4.0.7 02/28/2017
[   73.337434] RIP: 0010:refcount_warn_saturate+0xa7/0xf0
[   73.362283] RSP: 0018:ffffc9000081f798 EFLAGS: 00010282
[   73.367761] RAX: 0000000000000000 RBX: ffffc90000420f80 RCX: 0000000000000000
[   73.375200] RDX: ffff88811ad22d00 RSI: ffff88811ad171e0 RDI: ffff88811ad171e0
[   73.382590] RBP: 0000000000000900 R08: ffffffff82298f28 R09: 0000000000000058
[   73.390008] R10: 0000000000000219 R11: ffffffff82280f40 R12: 0000000000000090
[   73.397356] R13: ffff888102343a40 R14: ffff88810359e0e4 R15: 0000000000000000
[   73.404806] FS:  00007ff38d31d740(0000) GS:ffff88811ad00000(0000) knlGS:0000000000000000
[   73.413129] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   73.419096] CR2: 000055cff35f13f8 CR3: 0000000106391000 CR4: 00000000000406e0
[   73.426565] Call Trace:
[   73.429087]  <TASK>
[   73.431314]  igb_clean_tx_ring+0x43/0x140 [igb]
[   73.436002]  igb_down+0x1d7/0x220 [igb]
[   73.439974]  __igb_close+0x3c/0x120 [igb]
[   73.444118]  igb_xdp+0x10c/0x150 [igb]
[   73.447983]  ? igb_pci_sriov_configure+0x70/0x70 [igb]
[   73.453362]  dev_xdp_install+0xda/0x110
[   73.457371]  dev_xdp_attach+0x1da/0x550
[   73.461369]  do_setlink+0xfd0/0x10f0
[   73.465166]  ? __nla_validate_parse+0x89/0xc70
[   73.469714]  rtnl_setlink+0x11a/0x1e0
[   73.473547]  rtnetlink_rcv_msg+0x145/0x3d0
[   73.477709]  ? rtnl_calcit.isra.0+0x130/0x130
[   73.482258]  netlink_rcv_skb+0x8d/0x110
[   73.486229]  netlink_unicast+0x230/0x340
[   73.490317]  netlink_sendmsg+0x215/0x470
[   73.494395]  __sys_sendto+0x179/0x190
[   73.498268]  ? move_addr_to_user+0x37/0x70
[   73.502547]  ? __sys_getsockname+0x84/0xe0
[   73.506853]  ? netlink_setsockopt+0x1c1/0x4a0
[   73.511349]  ? __sys_setsockopt+0xc8/0x1d0
[   73.515636]  __x64_sys_sendto+0x20/0x30
[   73.519603]  do_syscall_64+0x3b/0x80
[   73.523399]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[   73.528712] RIP: 0033:0x7ff38d41f20c
[   73.551866] RSP: 002b:00007fff3b945a68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[   73.559640] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ff38d41f20c
[   73.567066] RDX: 0000000000000034 RSI: 00007fff3b945b30 RDI: 0000000000000003
[   73.574457] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
[   73.581852] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff3b945ab0
[   73.589179] R13: 0000000000000000 R14: 0000000000000003 R15: 00007fff3b945b30
[   73.596545]  </TASK>
[   73.598842] ---[ end trace 0000000000000000 ]---

Fixes: 9cbc948b ("igb: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/e5c01d549dc37bff18e46aeabd6fb28a7bcf84be.1655388571.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

3f6a57ee

Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf · 582573f1

Jakub Kicinski authored Jun 17, 2022

Daniel Borkmann says:

====================
pull-request: bpf 2022-06-17

We've added 12 non-merge commits during the last 4 day(s) which contain
a total of 14 files changed, 305 insertions(+), 107 deletions(-).

The main changes are:

1) Fix x86 JIT tailcall count offset on BPF-2-BPF call, from Jakub Sitnicki.

2) Fix a kprobe_multi link bug which misplaces BPF cookies, from Jiri Olsa.

3) Fix an infinite loop when processing a module's BTF, from Kumar Kartikeya Dwivedi.

4) Fix getting a rethook only in RCU available context, from Masami Hiramatsu.

5) Fix request socket refcount leak in sk lookup helpers, from Jon Maxwell.

6) Fix xsk xmit behavior which wrongly adds skb to already full cq, from Ciara Loftus.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  rethook: Reject getting a rethook if RCU is not watching
  fprobe, samples: Add use_trace option and show hit/missed counter
  bpf, docs: Update some of the JIT/maintenance entries
  selftest/bpf: Fix kprobe_multi bench test
  bpf: Force cookies array to follow symbols sorting
  ftrace: Keep address offset in ftrace_lookup_symbols
  selftests/bpf: Shuffle cookies symbols in kprobe multi test
  selftests/bpf: Test tail call counting with bpf2bpf and data on stack
  bpf, x86: Fix tail call count offset calculation on bpf2bpf call
  bpf: Limit maximum modifier chain length in btf_check_type_tags
  bpf: Fix request_sock leak in sk lookup helpers
  xsk: Fix generic transmit when completion queue reservation fails
====================

Link: https://lore.kernel.org/r/20220617202119.2421-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

582573f1

17 Jun, 2022 15 commits

netfilter: cttimeout: fix slab-out-of-bounds read typo in cttimeout_net_exit · 394e7716

Florian Westphal authored Jun 15, 2022

syzbot reports:
  BUG: KASAN: slab-out-of-bounds in __list_del_entry_valid+0xcc/0xf0 lib/list_debug.c:42
  [..]
  list_del include/linux/list.h:148 [inline]
  cttimeout_net_exit+0x211/0x540 net/netfilter/nfnetlink_cttimeout.c:617

Problem is the wrong name of the list member, so container_of() result is wrong.

Reported-by: <syzbot+92968395eedbdbd3617d@syzkaller.appspotmail.com>
Fixes: 78222bac ("netfilter: cttimeout: decouple unlink and free on netns destruction")
Signed-off-by: Florian Westphal <fw@strlen.de>

394e7716

rethook: Reject getting a rethook if RCU is not watching · c0f3bb40

Masami Hiramatsu (Google) authored Jun 08, 2022

Since the rethook_recycle() will involve the call_rcu() for reclaiming
the rethook_instance, the rethook must be set up at the RCU available
context (non idle). This rethook_recycle() in the rethook trampoline
handler is inevitable, thus the RCU available check must be done before
setting the rethook trampoline.

This adds a rcu_is_watching() check in the rethook_try_get() so that
it will return NULL if it is called when !rcu_is_watching().

Fixes: 54ecbe6f ("rethook: Add a generic return hook")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/165461827269.280167.7379263615545598958.stgit@devnote2

c0f3bb40

fprobe, samples: Add use_trace option and show hit/missed counter · c88dbbcd

Masami Hiramatsu (Google) authored Jun 08, 2022

Add use_trace option to use trace_printk() instead of pr_info()
so that the handler doesn't involve the RCU operations.
And show the hit and missed counter so that the user can check
how many times the probe handler hit and missed.
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/165461826247.280167.11939123218334322352.stgit@devnote2

c88dbbcd

bpf, docs: Update some of the JIT/maintenance entries · 63ce81d1

Daniel Borkmann authored Jun 17, 2022

Various minor updates around some of the BPF-related entries:

JITs for ARM32/NFP/SPARC/X86-32 haven't seen updates in quite a while, thus
for now, mark them as 'Odd Fixes' until they become more actively developed.

JITs for POWERPC/S390 are in good shape and receive active development and
review, thus bump to 'Supported' similar as we have with X86-64/ARM64.

JITs for MIPS/RISC-V are in similar good shape as the ones mentioned above,
but looked after mostly in spare time, thus leave for now in 'Maintained' state.

Add Michael to PPC JIT given he's picking up the patches there, so it better
reflects today's state.

Also, I haven't done much reviewing around BPF sockmap/kTLS after John and I
did the big rework back in the days to integrate sockmap with kTLS.

These days, most of this is taken care by John, Jakub {Sitnicki,Kicinski} and
others in the community, so remove myself from these two.

Lastly, move all BPF-related entries into one place, that is, move the sockmap
one over near rest of BPF.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/f9b8a63a0b48dc764bd4c50f87632889f5813f69.1655494758.git.daniel@iogearbox.netSigned-off-by: Alexei Starovoitov <ast@kernel.org>

63ce81d1

ipv4: ping: fix bind address validity check · b4a028c4

Riccardo Paolo Bestetti authored Jun 17, 2022

Commit 8ff978b8 ("ipv4/raw: support binding to nonlocal addresses")
introduced a helper function to fold duplicated validity checks of bind
addresses into inet_addr_valid_or_nonlocal(). However, this caused an
unintended regression in ping_check_bind_addr(), which previously would
reject binding to multicast and broadcast addresses, but now these are
both incorrectly allowed as reported in [1].

This patch restores the original check. A simple reordering is done to
improve readability and make it evident that multicast and broadcast
addresses should not be allowed. Also, add an early exit for INADDR_ANY
which replaces lost behavior added by commit 0ce779a9 ("net: Avoid
unnecessary inet_addr_type() call when addr is INADDR_ANY").

Furthermore, this patch introduces regression selftests to catch these
specific cases.

[1] https://lore.kernel.org/netdev/CANP3RGdkAcDyAZoT1h8Gtuu0saq+eOrrTiWbxnOs+5zn+cpyKg@mail.gmail.com/

Fixes: 8ff978b8 ("ipv4/raw: support binding to nonlocal addresses")
Cc: Miaohe Lin <linmiaohe@huawei.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Riccardo Paolo Bestetti <pbl@bestov.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

b4a028c4

hamradio: 6pack: fix array-index-out-of-bounds in decode_std_command() · 2b04495e

Xu Jia authored Jun 17, 2022

Hulk Robot reports incorrect sp->rx_count_cooked value in decode_std_command().
This should be caused by the subtracting from sp->rx_count_cooked before.
It seems that sp->rx_count_cooked value is changed to 0, which bypassed the
previous judgment.

The situation is shown below:

         (Thread 1)			|  (Thread 2)
decode_std_command()		| resync_tnc()
...					|
if (rest == 2)			|
	sp->rx_count_cooked -= 2;	|
else if (rest == 3)			| ...
					| sp->rx_count_cooked = 0;
	sp->rx_count_cooked -= 1;	|
for (i = 0; i < sp->rx_count_cooked; i++) // report error
	checksum += sp->cooked_buf[i];

sp->rx_count_cooked is a shared variable but is not protected by a lock.
The same applies to sp->rx_count. This patch adds a lock to fix the bug.

The fail log is shown below:
=======================================================================
UBSAN: array-index-out-of-bounds in drivers/net/hamradio/6pack.c:925:31
index 400 is out of range for type 'unsigned char [400]'
CPU: 3 PID: 7433 Comm: kworker/u10:1 Not tainted 5.18.0-rc5-00163-g4b97bac0 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
Workqueue: events_unbound flush_to_ldisc
Call Trace:
 <TASK>
 dump_stack_lvl+0xcd/0x134
 ubsan_epilogue+0xb/0x50
 __ubsan_handle_out_of_bounds.cold+0x62/0x6c
 sixpack_receive_buf+0xfda/0x1330
 tty_ldisc_receive_buf+0x13e/0x180
 tty_port_default_receive_buf+0x6d/0xa0
 flush_to_ldisc+0x213/0x3f0
 process_one_work+0x98f/0x1620
 worker_thread+0x665/0x1080
 kthread+0x2e9/0x3a0
 ret_from_fork+0x1f/0x30
 ...
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xu Jia <xujia39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

2b04495e

tipc: fix use-after-free Read in tipc_named_reinit · 911600bf

Hoang Le authored Jun 17, 2022

syzbot found the following issue on:
==================================================================
BUG: KASAN: use-after-free in tipc_named_reinit+0x94f/0x9b0
net/tipc/name_distr.c:413
Read of size 8 at addr ffff88805299a000 by task kworker/1:9/23764

CPU: 1 PID: 23764 Comm: kworker/1:9 Not tainted
5.18.0-rc4-syzkaller-00878-g17d49e6e #0
Hardware name: Google Compute Engine/Google Compute Engine,
BIOS Google 01/01/2011
Workqueue: events tipc_net_finalize_work
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
 print_address_description.constprop.0.cold+0xeb/0x495
mm/kasan/report.c:313
 print_report mm/kasan/report.c:429 [inline]
 kasan_report.cold+0xf4/0x1c6 mm/kasan/report.c:491
 tipc_named_reinit+0x94f/0x9b0 net/tipc/name_distr.c:413
 tipc_net_finalize+0x234/0x3d0 net/tipc/net.c:138
 process_one_work+0x996/0x1610 kernel/workqueue.c:2289
 worker_thread+0x665/0x1080 kernel/workqueue.c:2436
 kthread+0x2e9/0x3a0 kernel/kthread.c:376
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298
 </TASK>
[...]
==================================================================

In the commit
d966ddcc ("tipc: fix a deadlock when flushing scheduled work"),
the cancel_work_sync() function just to make sure ONLY the work
tipc_net_finalize_work() is executing/pending on any CPU completed before
tipc namespace is destroyed through tipc_exit_net(). But this function
is not guaranteed the work is the last queued. So, the destroyed instance
may be accessed in the work which will try to enqueue later.

In order to completely fix, we re-order the calling of cancel_work_sync()
to make sure the work tipc_net_finalize_work() was last queued and it
must be completed by calling cancel_work_sync().

Reported-by: syzbot+47af19f3307fc9c5c82e@syzkaller.appspotmail.com
Fixes: d966ddcc ("tipc: fix a deadlock when flushing scheduled work")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

911600bf

veth: Add updating of trans_start · e66e257a

Jay Vosburgh authored Jun 16, 2022

Since commit 21a75f09 ("bonding: Fix ARP monitor validation"),
the bonding ARP / ND link monitors depend on the trans_start time to
determine link availability. NETIF_F_LLTX drivers must update trans_start
directly, which veth does not do. This prevents use of the ARP or ND link
monitors with veth interfaces in a bond.

Resolve this by having veth_xmit update the trans_start time.
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: 21a75f09 ("bonding: Fix ARP monitor validation")
Link: https://lore.kernel.org/netdev/b2fd4147-8f50-bebd-963a-1a3e8d1d9715@redhat.com/Signed-off-by: David S. Miller <davem@davemloft.net>

e66e257a

net: fix data-race in dev_isalive() · cc26c266

Eric Dumazet authored Jun 16, 2022

dev_isalive() is called under RTNL or dev_base_lock protection.

This means that changes to dev->reg_state should be done with both locks held.

syzbot reported:

BUG: KCSAN: data-race in register_netdevice / type_show

write to 0xffff888144ecf518 of 1 bytes by task 20886 on cpu 0:
register_netdevice+0xb9f/0xdf0 net/core/dev.c:10050
lapbeth_new_device drivers/net/wan/lapbether.c:414 [inline]
lapbeth_device_event+0x4a0/0x6c0 drivers/net/wan/lapbether.c:456
notifier_call_chain kernel/notifier.c:87 [inline]
raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:455
__dev_notify_flags+0x1d6/0x3a0
dev_change_flags+0xa2/0xc0 net/core/dev.c:8607
do_setlink+0x778/0x2230 net/core/rtnetlink.c:2780
__rtnl_newlink net/core/rtnetlink.c:3546 [inline]
rtnl_newlink+0x114c/0x16a0 net/core/rtnetlink.c:3593
rtnetlink_rcv_msg+0x811/0x8c0 net/core/rtnetlink.c:6089
netlink_rcv_skb+0x13e/0x240 net/netlink/af_netlink.c:2501
rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:6107
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x58a/0x660 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x661/0x750 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
__sys_sendto+0x21e/0x2c0 net/socket.c:2119
__do_sys_sendto net/socket.c:2131 [inline]
__se_sys_sendto net/socket.c:2127 [inline]
__x64_sys_sendto+0x74/0x90 net/socket.c:2127
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0

read to 0xffff888144ecf518 of 1 bytes by task 20423 on cpu 1:
dev_isalive net/core/net-sysfs.c:38 [inline]
netdev_show net/core/net-sysfs.c:50 [inline]
type_show+0x24/0x90 net/core/net-sysfs.c:112
dev_attr_show+0x35/0x90 drivers/base/core.c:2095
sysfs_kf_seq_show+0x175/0x240 fs/sysfs/file.c:59
kernfs_seq_show+0x75/0x80 fs/kernfs/file.c:162
seq_read_iter+0x2c3/0x8e0 fs/seq_file.c:230
kernfs_fop_read_iter+0xd1/0x2f0 fs/kernfs/file.c:235
call_read_iter include/linux/fs.h:2052 [inline]
new_sync_read fs/read_write.c:401 [inline]
vfs_read+0x5a5/0x6a0 fs/read_write.c:482
ksys_read+0xe8/0x1a0 fs/read_write.c:620
__do_sys_read fs/read_write.c:630 [inline]
__se_sys_read fs/read_write.c:628 [inline]
__x64_sys_read+0x3e/0x50 fs/read_write.c:628
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0

value changed: 0x00 -> 0x01

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 20423 Comm: udevd Tainted: G W 5.19.0-rc2-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cc26c266

phy: aquantia: Fix AN when higher speeds than 1G are not advertised · 9b7fd167

Claudiu Manoil authored Jun 10, 2022

Even when the eth port is resticted to work with speeds not higher than 1G,
and so the eth driver is requesting the phy (via phylink) to advertise up
to 1000BASET support, the aquantia phy device is still advertising for 2.5G
and 5G speeds.
Clear these advertising defaults when requested.

Cc: Ondrej Spacek <ondrej.spacek@nxp.com>
Fixes: 09c4c57f ("net: phy: aquantia: add support for auto-negotiation configuration")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220610084037.7625-1-claudiu.manoil@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

9b7fd167

Merge branch 'bpf: Fix cookie values for kprobe multi' · a4a8b2ee

Alexei Starovoitov authored Jun 16, 2022

Jiri Olsa says:

====================

hi,
there's bug in kprobe_multi link that makes cookies misplaced when
using symbols to attach. The reason is that we sort symbols by name
but not adjacent cookie values. Current test did not find it because
bpf_fentry_test* are already sorted by name.

v3 changes:
  - fixed kprobe_multi bench test to filter out invalid entries
    from available_filter_functions

v2 changes:
  - rebased on top of bpf/master
  - checking if cookies are defined later in swap function [Andrii]
  - added acks

thanks,
jirka
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

a4a8b2ee

selftest/bpf: Fix kprobe_multi bench test · 73006702

Jiri Olsa authored Jun 15, 2022

With [1] the available_filter_functions file contains records
starting with __ftrace_invalid_address___ and marking disabled
entries.

We need to filter them out for the bench test to pass only
resolvable symbols to kernel.

[1] commit b39181f7 ("ftrace: Add FTRACE_MCOUNT_MAX_OFFSET to avoid adding weak function")

Fixes: b39181f7 ("ftrace: Add FTRACE_MCOUNT_MAX_OFFSET to avoid adding weak function")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220615112118.497303-5-jolsa@kernel.orgSigned-off-by: Alexei Starovoitov <ast@kernel.org>

73006702

bpf: Force cookies array to follow symbols sorting · eb5fb032

Jiri Olsa authored Jun 15, 2022

When user specifies symbols and cookies for kprobe_multi link
interface it's very likely the cookies will be misplaced and
returned to wrong functions (via get_attach_cookie helper).

The reason is that to resolve the provided functions we sort
them before passing them to ftrace_lookup_symbols, but we do
not do the same sort on the cookie values.

Fixing this by using sort_r function with custom swap callback
that swaps cookie values as well.

Fixes: 0236fec5 ("bpf: Resolve symbols with ftrace_lookup_symbols for kprobe multi link")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220615112118.497303-4-jolsa@kernel.orgSigned-off-by: Alexei Starovoitov <ast@kernel.org>

eb5fb032

ftrace: Keep address offset in ftrace_lookup_symbols · eb1b2985

Jiri Olsa authored Jun 15, 2022

We want to store the resolved address on the same index as
the symbol string, because that's the user (bpf kprobe link)
code assumption.

Also making sure we don't store duplicates that might be
present in kallsyms.
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Fixes: bed0d9a5 ("ftrace: Add ftrace_lookup_symbols function")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220615112118.497303-3-jolsa@kernel.orgSigned-off-by: Alexei Starovoitov <ast@kernel.org>

eb1b2985

selftests/bpf: Shuffle cookies symbols in kprobe multi test · ad884853

Jiri Olsa authored Jun 15, 2022

There's a kernel bug that causes cookies to be misplaced and
the reason we did not catch this with this test is that we
provide bpf_fentry_test* functions already sorted by name.

Shuffling function bpf_fentry_test2 deeper in the list and
keeping the current cookie values as before will trigger
the bug.

The kernel fix is coming in following changes.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220615112118.497303-2-jolsa@kernel.orgSigned-off-by: Alexei Starovoitov <ast@kernel.org>

ad884853

16 Jun, 2022 4 commits

selftests/bpf: Test tail call counting with bpf2bpf and data on stack · 5e0b0a4c

Jakub Sitnicki authored Jun 16, 2022

Cover the case when tail call count needs to be passed from BPF function to
BPF function, and the caller has data on stack. Specifically when the size
of data allocated on BPF stack is not a multiple on 8.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220616162037.535469-3-jakub@cloudflare.com

5e0b0a4c

bpf, x86: Fix tail call count offset calculation on bpf2bpf call · ff672c67

Jakub Sitnicki authored Jun 16, 2022

On x86-64 the tail call count is passed from one BPF function to another
through %rax. Additionally, on function entry, the tail call count value
is stored on stack right after the BPF program stack, due to register
shortage.

The stored count is later loaded from stack either when performing a tail
call - to check if we have not reached the tail call limit - or before
calling another BPF function call in order to pass it via %rax.

In the latter case, we miscalculate the offset at which the tail call count
was stored on function entry. The JIT does not take into account that the
allocated BPF program stack is always a multiple of 8 on x86, while the
actual stack depth does not have to be.

This leads to a load from an offset that belongs to the BPF stack, as shown
in the example below:

SEC("tc")
int entry(struct __sk_buff *skb)
{
	/* Have data on stack which size is not a multiple of 8 */
	volatile char arr[1] = {};
	return subprog_tail(skb);
}

int entry(struct __sk_buff * skb):
   0: (b4) w2 = 0
   1: (73) *(u8 *)(r10 -1) = r2
   2: (85) call pc+1#bpf_prog_ce2f79bb5f3e06dd_F
   3: (95) exit

int entry(struct __sk_buff * skb):
   0xffffffffa0201788:  nop    DWORD PTR [rax+rax*1+0x0]
   0xffffffffa020178d:  xor    eax,eax
   0xffffffffa020178f:  push   rbp
   0xffffffffa0201790:  mov    rbp,rsp
   0xffffffffa0201793:  sub    rsp,0x8
   0xffffffffa020179a:  push   rax
   0xffffffffa020179b:  xor    esi,esi
   0xffffffffa020179d:  mov    BYTE PTR [rbp-0x1],sil
   0xffffffffa02017a1:  mov    rax,QWORD PTR [rbp-0x9]	!!! tail call count
   0xffffffffa02017a8:  call   0xffffffffa02017d8       !!! is at rbp-0x10
   0xffffffffa02017ad:  leave
   0xffffffffa02017ae:  ret

Fix it by rounding up the BPF stack depth to a multiple of 8, when
calculating the tail call count offset on stack.

Fixes: ebf7d1f5 ("bpf, x64: rework pro/epilogue and tailcall handling in JIT")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220616162037.535469-2-jakub@cloudflare.com

ff672c67

Merge tag 'net-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net · 48a23ec6

Linus Torvalds authored Jun 16, 2022

Pull networking fixes from Jakub Kicinski:
 "Mostly driver fixes.

  Current release - regressions:

   - Revert "net: Add a second bind table hashed by port and address",
     needs more work

   - amd-xgbe: use platform_irq_count(), static setup of IRQ resources
     had been removed from DT core

   - dts: at91: ksz9477_evb: add phy-mode to fix port/phy validation

  Current release - new code bugs:

   - hns3: modify the ring param print info

  Previous releases - always broken:

   - axienet: make the 64b addressable DMA depends on 64b architectures

   - iavf: fix issue with MAC address of VF shown as zero

   - ice: fix PTP TX timestamp offset calculation

   - usb: ax88179_178a needs FLAG_SEND_ZLP

  Misc:

   - document some net.sctp.* sysctls"

* tag 'net-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (31 commits)
  net: axienet: add missing error return code in axienet_probe()
  Revert "net: Add a second bind table hashed by port and address"
  net: ax25: Fix deadlock caused by skb_recv_datagram in ax25_recvmsg
  net: usb: ax88179_178a needs FLAG_SEND_ZLP
  MAINTAINERS: add include/dt-bindings/net to NETWORKING DRIVERS
  ARM: dts: at91: ksz9477_evb: fix port/phy validation
  net: bgmac: Fix an erroneous kfree() in bgmac_remove()
  ice: Fix memory corruption in VF driver
  ice: Fix queue config fail handling
  ice: Sync VLAN filtering features for DVM
  ice: Fix PTP TX timestamp offset calculation
  mlxsw: spectrum_cnt: Reorder counter pools
  docs: networking: phy: Fix a typo
  amd-xgbe: Use platform_irq_count()
  octeontx2-vf: Add support for adaptive interrupt coalescing
  xilinx:  Fix build on x86.
  net: axienet: Use iowrite64 to write all 64b descriptor pointers
  net: axienet: make the 64b addresable DMA depends on 64b archectures
  net: hns3: fix tm port shapping of fibre port is incorrect after driver initialization
  net: hns3: fix PF rss size initialization bug
  ...

48a23ec6

net: axienet: add missing error return code in axienet_probe() · 2e7bf4a6

Yang Yingliang authored Jun 16, 2022

It should return error code in error path in axienet_probe().

Fixes: 00be43a7 ("net: axienet: make the 64b addresable DMA depends on 64b archectures")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220616062917.3601-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

2e7bf4a6