Putting an empty 'mlx5_flow_spec' structure on the stack is a bit
wasteful and causes a warning on 32-bit architectures when building
with clang -fsanitize-coverage:

drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c: In function 'mlx5_eswitch_termtbl_create':
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c:90:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

Since the structure is never written to, we can statically allocate
it to avoid the stack usage. To be on the safe side, mark all
subsequent function arguments that we pass it into as 'const'
as well.

Fixes: 10caabda ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Consider PCI and non PCI device types while setting device name
in get_drvinfo() callback using existing generic device.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently PF phys_port_name is named as pfNvf-1 as vport number for PF
vport is 65535.
Correct PF's phys_port name as agreed upon name as pfN.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Set supported device features in the netdevice MPLS features mask.
This will enable HW checksumming and TSO for MPLS tagged traffic.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch changes the way the driver advertises its checksum offload
capabilities within the net device features bit mask.

Instead of advertising protocol specific checksumming capabilities
which are limited today to IPv4 and IPv6, we move to reporing
generic HW checksumming capabilities.

This will allow the network stack to let mlx5 device offload checksum
for cases where the IP header is encapsulated within another protocol
and the skb->protocol doesn't indicate one of the IP versions protocol,
specifically in the case of MPLS label encapsulating the IP header and
the skb->protocol indiciates MPLS ethertype rather than IP.

Moving the HW_CSUM reporting is required in the basic net device hw
features mask and also in the extensions (vlan and encpasulation
features) since the extensions are always multiplied by the basic
features set during the packet's traversal through the stack's tx flow.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Remove the limitation preventing adding a vport's MAC address to the
Multi-Physical Function Switch (MPFS) more than once per E-switch, as
there is no difference in the MPFS if an address is being used by an
E-switch more than once.

This allows the E-switch to have multiple vports with the same MAC
address, allowing vports to be classified by VLAN id instead of by MAC
if desired.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Unify and isolate the error handling flow in mlx5_mpfs_add_mac(),
removing code duplication.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Misc updates from mlx5-next branch:

1) E-Switch vport metadata support for source vport matching
2) Convert mkey_table to XArray
3) Shared IRQs and to use single IRQ for all async EQs
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Tools such as vpnc try to flush routes when run inside network
namespaces by writing 1 into /proc/sys/net/ipv4/route/flush. This
currently does not work because flush is not enabled in non-initial
network namespaces.
Since routes are per network namespace it is safe to enable
/proc/sys/net/ipv4/route/flush in there.

Link: https://github.com/lxc/lxd/issues/4257Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - fix includes for _MAX constants, atomic functions and fwdecls,
   by Sven Eckelmann (3 patches)

 - shorten multicast tt/tvlv worker spinlock section, by Linus Luessing

 - routeable multicast preparations: implement MAC multicast filtering,
   by Linus Luessing (2 patches, David Millers comments integrated)

 - remove return value checks for debugfs_create, by Greg Kroah-Hartman

 - add routable multicast optimizations, by Linus Luessing (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: some code optimizations & cleanups & bugfixes

[patch 01/12] fixes a TX timeout issue.

[patch 02/12 - 04/12] adds some patch related to TM module.

[patch 05/12] fixes a compile warning.

[patch 06/12] adds Asym Pause support for autoneg

[patch 07/12] optimizes the error handler for VF reset.

[patch 08/12] deals with the empty interrupt case.

[patch 09/12 - 12/12] adds some cleanups & optimizations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If CMDQ ring is full, hclge_cmd_send may return directly, but IMP still
working and HW pointer changed, SW ring pointer do not match the HW
pointer. This patch update the SW pointer every time when the space is
full, so it can work normally next time if IMP and HW still working.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The HNS3_RXD_VLD_B bit has already been checked in hns3_add_frag
or hns3_handle_rx_bd before calling hns3_handle_bdinfo, so when
hns3_handle_bdinfo is called, the HNS3_RXD_VLD_B bit is always
set, which makes the checking in hns3_handle_bdinfo unnecessary.

This patch removes the RXD_VLD_B checking in hns3_handle_bdinfo.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes unused linkmode definition.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The frame column is based on rx_crc_errors and rx_frame_errors. So
l3l4 checksum error should not be counted by rx_crc_errors. Instead,
l3l4 checksum error should be counted in ifconfig error column.

Fixes: d3ec4ef6 ("net: hns3: refactor the statistics updating for netdev")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since some MSI-X interrupt's status may be cleared by hardware,
so when the driver receives the interrupt, reading
HCLGE_VECTOR0_PF_OTHER_INT_STS_REG register will get an empty
unknown interrupt. For this case, the irq handler should enable
vector0 interrupt. This patch also use dev_info() instead of
dev_dbg() in the hclge_check_event_cause(), since this information
will be useful for normal usage.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VF reset may fail for some probabilistic reasons,
such as wait for hardware reset timeout, wait for mailbox
response timeout, so this patch tries to re-schedule the
reset task when the number of reset failing is under
HCLGEVF_RESET_MAX_FAIL_CNT. This patch also add a function
hclgevf_reset_err_handle() to handle the reset failing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Local device and link partner config auto-negotiation on both,
local device config pause frame use as: rx on/tx off,
link partner config pause frame use as: rx off/tx on.

We except the result is:
Local device:
Autonegotiate:  on
RX:             on
TX:             off
RX negotiated:  on
TX negotiated:  off

Link partner:
Autonegotiate:  on
RX:             off
TX:             on
RX negotiated:  off
TX negotiated:  on

But actually, the result of Local device and link partner is both:
Autonegotiate:  on
RX:             off
TX:             off
RX negotiated:  off
TX negotiated:  off

The root cause is that the supported flag is has only Pause,
reference to the function genphy_config_advert():
static int genphy_config_advert(struct phy_device *phydev)
{
	...
	linkmode_and(phydev->advertising, phydev->advertising,
		     phydev->supported);
	...
}
The pause frame use of link partner is rx off/tx on, so its
advertising only set the bit Asym_Pause, and the supported is
only set the bit Pause, so the result of linkmode_and(), is
rx off/tx off.

This patch adds Asym_Pause to the supported flag to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting -Wformat=2, there is a compiler warning like this:

hclge_main.c:xxx:x: warning: format not a string literal and no
format arguments [-Wformat-nonliteral]
strs[i].desc);
^~~~

This patch adds missing format parameter "%s" to snprintf() to
fix it.

Fixes: 46a3df9f ("Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When hdev->tx_sch_mode is HCLGE_FLAG_VNET_BASE_SCH_MODE, the
hclge_tm_schd_mode_vnet_base_cfg calls hclge_tm_pri_schd_mode_cfg
with vport->vport_id as pri_id, which is used as index for
hdev->tm_info.tc_info, it will cause out of bound access issue
if vport_id is equal to or larger than HNAE3_MAX_TC.

Also hardware only support maximum speed of HCLGE_ETHER_MAX_RATE.

So this patch adds two checks for above cases.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when there is share buffer in the SSU(storage
switching unit), the low waterline for RX private buffer is
too low to keep the hardware running. Hardware may have
processed all the packet stored in the private buffer of the
low waterline before the new packet comes, because hardware
only tell the peer send packet again when the private buffer
is under the low waterline.

So this patch only allocate RX private buffer if there is
enough buffer according to hardware user manual.

This patch also reserve some buffer for reusing when TC num
is less than or equal to 2, and change PAUSE_TRANS_GAP &
HCLGE_NON_DCB_ADDITIONAL_BUF according to hardware user
manual.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when TC num is one, the DCB will be disabled no matter if
pfc_en is non-zero or not.

This patch enables the DCB if pfc_en is non-zero, even when TC num
is one.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When change MTU or other operations, which just calling .reset_notify
to do HNAE3_DOWN_CLIENT and HNAE3_UP_CLIENT, then
the netdev_tx_reset_queue() in the hns3_clear_all_ring() will be
ignored. So the dev_watchdog() may misdiagnose a TX timeout.

This patch separates netdev_tx_reset_queue() from
hns3_clear_all_ring(), and unifies hns3_clear_all_ring() and
hns3_force_clear_all_ring into one, since they are doing
similar things.

Fixes: 3a30964a ("net: hns3: delay ring buffer clearing during reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Better PHYLINK compliance for SJA1105 DSA

After discussing with Russell King, it appears this driver is making a
few confusions and not performing some checks for consistent operation.

Changes in v2:
- Removed redundant print in the phylink_validate callback (in 2/3).
====================
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need a better way to signal this, perhaps in phylink_validate, but
for now just print this error message as guidance for other people
looking at this driver's code while trying to rework PHYLINK.

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHYLINK being designed with PHYs in mind that can change MII protocol,
for correct operation it is necessary to ensure that the PHY interface
mode stays the same (otherwise clear the supported bit mask, as
required).

Because this is just a hypothetical situation for now, we don't bother
to check whether we could actually support the new PHY interface mode.
Actually we could modify the xMII table, reset the switch and send an
updated static configuration, but adding that would just be dead code.

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It has been pointed out that PHYLINK can call mac_config only to update
the phy_interface_type and without knowing what the AN results are.

Experimentally, when this was observed to happen, state->link was also
unset, and therefore was used as a proxy to ignore this call. However it
is also suggested that state->link is undefined for this callback and
should not be relied upon.

So let the previously-dead codepath for SPEED_UNKNOWN be called, and
update the comment to make sure the MAC's behavior is sane.

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On 32-bit architectures, putting an array of 256 u32 values on the
stack uses more space than the warning limit:

drivers/net/ethernet/huawei/hinic/hinic_main.c: In function 'hinic_rss_init':
drivers/net/ethernet/huawei/hinic/hinic_main.c:286:1: error: the frame size of 1068 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

I considered changing the code to use u8 values here, since that's
all the hardware supports, but dynamically allocating the array is
a more isolated fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: stmmac: 10GbE using XGMAC

Support for 10Gb Link using XGMAC core plus some performance tweaks.

Tested in a PCI based setup.

iperf3 TCP results:
	TSO ON, MTU=1500, TX Queues = 1, RX Queues = 1, Flow Control ON
	Pinned CPU (-A), Zero-Copy (-Z)

[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-600.00 sec   643 GBytes  9.21 Gbits/sec    1             sender
[  5]   0.00-600.00 sec   643 GBytes  9.21 Gbits/sec                  receiver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We support more speeds now. Update the Kconfig entry.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only disable the interrupts if RX NAPI gets to be scheduled. Also,
schedule the TX NAPI only when the interrupts are disabled.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the RX Tail Pointer to the last available SKB entry.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, stmmac only supports 32 bits addressing for SKB. Enable the
support for upto 48 bits addressing in XGMAC core.

This avoids the use of bounce buffers and increases performance.

Changes from v1:
	- Fallback to 32 bits in failure (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a performance killer and anyways the interrupts are being
disabled by RX NAPI so no need to disable them again.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XGMAC supports following speeds:
	- 10G XGMII
	- 5G XGMII
	- 2.5G XGMII
	- 2.5G GMII
	- 1G GMII
	- 100M MII
	- 10M MII

Add them to the stmmac driver.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Undefined burst shall only be set if pdata asks to.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For performance reasons decrease the default RX Watchdog value for the
minimum allowed.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not enable EEE feature in the PHY if MAC does not support it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable the EDMA feature by default which gives higher performance.

Changes from v1:
	- Do not use magic values (David)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some DT bindings do not have the PHY handle. Let's fallback to manually
discovery in case phylink_of_phy_connect() fails.

Changes from v1:
	- Fixup comment style (Sergei)

Fixes: 74371272 ("net: stmmac: Convert to phylink and remove phylib logic")
Reported-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Tested-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>