Systems based upon the Loongson 1B & 1C CPUs share the same load
address, as do those based upon Loongson 1A. Unify the definition of
this load address to reduce duplication & avoid the need for an extra
Loongson 1A case in future.

[paul.burton@mips.com: Rewrite commit message.]
Signed-off-by: 谢致邦 (XIE Zhibang) <Yeking@Red54.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/14927/
Cc: linux-mips@linux-mips.org

LS232 (Loonson 2-issue 32-bit, also called GS232 (Godson 2-issue 32-bit))
is the CPU core (microarchitecture) of Loongson 1A/1B/1C.

According to "LS232 用户手册 (LS232 User Manual)", LS232 implements the
MIPS32 Release 1 instruction set, and part of the MIPS32 Release 2
instruction set.

In the manual, LS232 implements all of the MIPS32R2 instruction set
except the FPU instructions, and LS232 also implements 5 FPU
instructions of the MIPS32R2 instruction set: CEIL.L.fmt, CVT.L.fmt,
FLOOR.L.fmt, TRUNC.L.fmt, and ROUND.L.fmt.

But a bug of the DI instruction has been found during tests, the DI
instruction can not disable interrupts in arch_local_irq_disable() with
CONFIG_PREEMPT_NONE=y and CFLAGS='-mno-branch-likely' in some cases.

[paul.burton@mips.com:
  - Remove the _MIPS_ISA redefinition to match the change made for the
    generic MIPSr1 CPUs by commit 344ebf09 ("MIPS: Always use
    -march=<arch>, not -<arch> shortcuts").]
Signed-off-by: 谢致邦 (XIE Zhibang) <Yeking@Red54.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/16155/
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org

The GPIO controller also serves as an interrupt controller for events
on the GPIO it handles.

An interrupt occurs whenever a GPIO line has changed.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20015/
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: thomas.petazzoni@bootlin.com

Enable CONFIG_MIPS_AUTO_PFN_OFFSET for the generic platform, allowing
it to avoid wasted book-keeping for pages with addresses lower than the
physical base address of memory.

This has a minimal impact on kernel text size, with 64r6el_defconfig
gaining 0.1% in size as reported by bloat-o-meter:

  add/remove: 4/1 grow/shrink: 345/13 up/down: 9017/-392 (8625)
  Function                                     old     new   delta
  pcpu_setup_first_chunk                      1444    1780    +336
  pcpu_alloc_first_chunk                       864    1136    +272
  start_kernel                                1064    1288    +224
  initcall_blacklist                           224     372    +148
  try_fill_recv                               2088    2184     +96
  ...
  Total: Before=8457273, After=8465898, chg +0.10%

The gain for systems with large offsets to physical memory & the ability
to continue using generic kernels on such systems seems well worth this
small cost.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/20049/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

On systems where physical memory begins at a non-zero address, defining
PHYS_OFFSET (which influences ARCH_PFN_OFFSET) can save us time & memory
by avoiding book-keeping for pages from address zero to the start of
memory.

Some MIPS platforms already make use of this, but with the definition of
PHYS_OFFSET being compile-time constant it hasn't been possible to
enable this optimization for a kernel which may run on systems with
varying physical memory base addresses.

Introduce a new Kconfig option CONFIG_MIPS_AUTO_PFN_OFFSET which, when
enabled, makes ARCH_PFN_OFFSET a variable & detects it from the boot
memory map (which for example may have been populated from DT). The
relationship with PHYS_OFFSET is reversed, with PHYS_OFFSET now being
based on ARCH_PFN_OFFSET. This is because ARCH_PFN_OFFSET is used far
more often, so avoiding the need for runtime calculation gives us a
smaller impact on kernel text size (0.1% rather than 0.15% for
64r6el_defconfig).
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/20048/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

isa_virt_to_bus() & isa_bus_to_virt() claim to treat ISA bus addresses
as being identical to physical addresses, but they fail to do so in the
presence of a non-zero PHYS_OFFSET.

Correct this by having them use virt_to_phys() & phys_to_virt(), which
consolidates the calculations to one place & ensures that ISA bus
addresses do indeed match physical addresses.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20047/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Vladimir Kondratiev <vladimir.kondratiev@intel.com>

Converting an address between cached & uncached (typically addresses in
(c)kseg0 & (c)kseg1 or 2 xkphys regions) should not depend upon
PHYS_OFFSET in any way - we're converting from a virtual address in one
unmapped region to a virtual address in another unmapped region.

For some reason our CAC_ADDR() & UNCAC_ADDR() macros make use of
PAGE_OFFSET, which typically includes PHYS_OFFSET. This means that
platforms with a non-zero PHYS_OFFSET typically have to workaround
miscalculation by these 2 macros by also defining UNCAC_BASE to a value
that isn't really correct.

It appears that an attempt has previously been made to address this with
commit 3f4579252aa1 ("MIPS: make CAC_ADDR and UNCAC_ADDR account for
PHYS_OFFSET") which was later undone by commit ed3ce16c ("Revert
"MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"") which
also introduced the ar7 workaround. That attempt at a fix was roughly
equivalent, but essentially caused the CAC_ADDR() & UNCAC_ADDR() macros
to cancel out PHYS_OFFSET by adding & then subtracting it again. In his
revert Leonid is correct that using PHYS_OFFSET makes no sense in the
context of these macros, but appears to have missed its inclusion via
PAGE_OFFSET which means PHYS_OFFSET actually had an effect after the
revert rather than before it.

Here we fix this by modifying CAC_ADDR() & UNCAC_ADDR() to stop using
PAGE_OFFSET (& thus PHYS_OFFSET), instead using __pa() & __va() along
with UNCAC_BASE.

For UNCAC_ADDR(), __pa() will convert a cached address to a physical
address which we can simply use as an offset from UNCAC_BASE to obtain
an address in the uncached region.

For CAC_ADDR() we can undo the effect of UNCAC_ADDR() by subtracting
UNCAC_BASE and using __va() on the result.

With this change made, remove definitions of UNCAC_BASE from the ar7 &
pic32 platforms which appear to have defined them only to workaround
this problem.
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: 3f4579252aa1 ("MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET")
References: ed3ce16c ("Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"")
Patchwork: https://patchwork.linux-mips.org/patch/20046/
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Vladimir Kondratiev <vladimir.kondratiev@intel.com>

of_find_compatible_node() returns a device_node pointer with refcount
incremented and must be decremented explicitly.
 As this code is using the result only to check presence of the interrupt
controller (!NULL) but not actually using the result otherwise the
refcount can be decremented here immediately again.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19820/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

The call to of_find_node_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented here after the last
usage.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19558/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

VDSO code should not be using smp_processor_id(), since it is executed
in user mode.
Introduce a VDSO-specific path which will cause a compile-time
or link-time error (depending upon support for __compiletime_error) if
the VDSO ever incorrectly attempts to use smp_processor_id().

[Matt Redfearn <matt.redfearn@imgtec.com>: Move before change to
smp_processor_id in series]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/17932/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org

Now that the GPIO driver support interrupts we don't need to poll the
buttons.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/15283/
Cc: linux-mips@linux-mips.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

mips_swiotlb_ops differs from the generic swiotlb_dma_ops only in that
it contains a mb() barrier after each operations that maps or syncs
dma memory to the device.

The dma operations are defined to not be memory barriers, but instead
the write* operations to kick the DMA off are supposed to contain them.

For mips this handled by war_io_reorder_wmb(), which evaluates to the
stronger wmb() instead of the pure compiler barrier barrier() for
just those platforms that use swiotlb, so I think we are covered
properly.

[paul.burton@mips.com:
  - Include linux/swiotlb.h to fix build failures for configs with
    CONFIG_SWIOTLB=y.]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20038/
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org

If a driver causes DMA cache maintenance with a zero length then we
currently BUG and kill the kernel. As this is a scenario that we may
well be able to recover from, WARN & return in the condition instead.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/14623/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

The binding for the USB PHY went thru before the driver. However the
new version of the driver now use the PHY core support for reset, and
this expect the reset to be named "phy". So remove the "usb-" prefix
from the the reset names.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/15282/
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org

There is an additional MIIM (MDIO) bus in this SoC so let's declare it
in the dtsi.

This bus requires GPIO 14 and 15 pins that need to be muxed. There is no
support for internal PHY reset on this bus on the contrary of MIIM0 so
there is only one register address space and not two.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20014/
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: thomas.petazzoni@bootlin.com

The length of memory address space for MIIM0 is from 0x7107009c to
0x710700bf included which is 36 bytes long in decimal, or 0x24 bytes in
hexadecimal and not 0x36.

Fixes: 49b03169 ("MIPS: mscc: Add switch to ocelot")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20013/
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: thomas.petazzoni@bootlin.com

The RTC definitions were moved to the driver, remove them from the platform
header.

[paul.burton@mips.com:
  - Also remove the unused tx4939_rtcptr which would use struct
    tx4939_rtc_reg if it were ever expanded.]
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20024/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org

The ar724x pci driver expects the PCIe controller to be brought out of
reset by the bootloader.

At least the AVM Fritz 300E bootloader doesn't take care of releasing
the different PCIe controller related resets which causes an endless
hang as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.

Do the full "PCIE Root Complex Initialization Sequence" if the PCIe
host controller is still in reset during probing.

The QCA u-boot sleeps 10ms after the PCIE Application Control bit is
set to ready. It has been shown that 10ms might not be enough time if
PCIe should be used right after setting the bit. During my tests it
took up to 20ms till the link was up. Giving the link up to 100ms
should work for all cases.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19916/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

This patch ensures, that the pinmux register is properly setup for the
boot console UART when early_printk is enabled.

[paul.burton@mips.com:
  - s/poinmux/pinmux/
  - s/uart/UART/
  - Drop extraneous parentheses.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

This patch adds a few additional cpu feature overrides so that they do not
need to be probed at runtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19914/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

This patch disables irq on reboot to fix hang issues that were observed
due to pending interrupts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19913/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

The pinmux on QCA SoCs is controlled by a single register. The
"pinctrl-single" driver can be used but requires the target
to select PINCTRL.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19909/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

This patch adds support for 2 new types of QCA silicon. TP9343 is
essentially the same as the QCA956X but is licensed by TPLink.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19911/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

This patch adds many new registers for various QCA MIPS SoCs. The patch is
an aggragate of many contributions made to OpenWrt.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19910/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

Ocelot now has a u-boot port, allow building FIT images instead of relying
on the legacy detection and builtin DTB.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19632/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

Get rid of extern declarations in .c functions and included
the necessary header file. Also remove unused UART declares.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19477/
Cc: linux-mips@linux-mips.org

It is not immediately obvious what the expected inputs to these fault
handlers is and how they calculate the number of unset bytes. Having
stared deeply at this in order to fix some corner cases, add some
comments to assist those who follow.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19339/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>

The __clear_user function is defined to return the number of bytes that
could not be cleared. From the underlying memset / bzero implementation
this means setting register a2 to that number on return. Currently if a
page fault is triggered within the MIPSr6 version of setting of initial
unaligned bytes, the value loaded into a2 on return is meaningless.

During the MIPSr6 version of the initial unaligned bytes block, register
a2 contains the number of bytes to be set beyond the initial unaligned
bytes. The t0 register is initally set to the number of unaligned bytes
- STORSIZE, effectively a negative version of the number of unaligned
bytes. This is then incremented before each byte is saved.

The label .Lbyte_fixup\@ is jumped to on page fault. Currently the value
in a2 is incorrectly replaced by 0 - t0 + 1, effectively the number of
unaligned bytes remaining. This leads to the failures being reported by
the following test code:

static int __init test_clear_user(void)
{
	int j, k;

	pr_info("\n\n\nTesting clear_user\n");
	for (j = 0; j < 512; j++) {
		if ((k = clear_user(NULL+3, j)) != j) {
			pr_err("clear_user (NULL %d) returned %d\n", j, k);
		}
	}
	return 0;
}
late_initcall(test_clear_user);

Which reports:
[    3.965439] Testing clear_user
[    3.973169] clear_user (NULL 8) returned 6
[    3.976782] clear_user (NULL 9) returned 6
[    3.980390] clear_user (NULL 10) returned 6
[    3.984052] clear_user (NULL 11) returned 6
[    3.987524] clear_user (NULL 12) returned 6

Fix this by subtracting t0 from a2 (rather than $0), effectivey giving:
unset_bytes = (#bytes - (#unaligned bytes)) - (-#unaligned bytes remaining + 1) + 1
     a2     =             a2                -              t0                   + 1

This fixes the value returned from __clear user when the number of bytes
to set is > LONGSIZE and the address is invalid and unaligned.

Unfortunately, this breaks the fixup handling for unaligned bytes after
the final long, where register a2 still contains the number of bytes
remaining to be set and the t0 register is to 0 - the number of
unaligned bytes remaining.

Because t0 is now is now subtracted from a2 rather than 0, the number of
bytes unset is reported incorrectly:

static int __init test_clear_user(void)
{
	char *test;
	int j, k;

	pr_info("\n\n\nTesting clear_user\n");
	test = vmalloc(PAGE_SIZE);

	for (j = 256; j < 512; j++) {
		if ((k = clear_user(test + PAGE_SIZE - 254, j)) != j - 254) {
			pr_err("clear_user (%px %d) returned %d\n",
				test + PAGE_SIZE - 254, j, k);
		}
	}
	return 0;
}
late_initcall(test_clear_user);

[    3.976775] clear_user (c00000000000df02 256) returned 4
[    3.981957] clear_user (c00000000000df02 257) returned 6
[    3.986425] clear_user (c00000000000df02 258) returned 8
[    3.990850] clear_user (c00000000000df02 259) returned 10
[    3.995332] clear_user (c00000000000df02 260) returned 12
[    3.999815] clear_user (c00000000000df02 261) returned 14

Fix this by ensuring that a2 is set to 0 during the set of final
unaligned bytes.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 8c56208a ("MIPS: lib: memset: Add MIPS R6 support")
Patchwork: https://patchwork.linux-mips.org/patch/19338/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.0+

Many architectural features have over time moved from being optional to
either be required or removed by newer architecture releases. This means
that in many cases we can know at compile time whether a feature will be
supported or not purely due to the knowledge we have about the ISA the
kernel build is targeting.

This patch introduces a bunch of utility macros for checking for
supported options, ASEs & combinations of those with ISA revisions. It
then makes use of these in the default definitions of cpu_has_* macros.
The result is that many of the macros become compile-time constant,
allowing more optimisation opportunities for the compiler - particularly
with kernels built for later ISA revisions.

To demonstrate the effect of this patch, the following table shows the
size in bytes of the kernel binary as reported by scripts/bloat-o-meter
for v4.12-rc4 maltasmvp_defconfig kernels with & without this patch. A
variant of maltasmvp_defconfig with CONFIG_CPU_MIPS32_R6 selected is
also shown, to demonstrate that MIPSr6 systems benefit more due to extra
features becoming required by that architecture revision. Builds of
pistachio_defconfig are also shown, as although this is a MIPSr2
platform it doesn't hardcode any features in a machine-specific
cpu-feature-overrides.h, which allows it to gain more from this patch
than the equivalent Malta r2 build.

     Config         | Before  | After   |  Change
    ----------------|---------|---------|---------
     maltasmvp      | 7248316 | 7247714 |    -602
     maltasmvp + r6 | 6955595 | 6950777 |   -4818
     pistachio      | 8650977 | 8363898 | -287079
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/16360/
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org

Make use of the spi-gpio driver to provide SPI support on the Ingenic
JZ4780 SoC using the pins that can be used with the SSI0 device as
GPIOs, until such time as we have support for the Ingenic SPI/SSI
controller.

[paul.burton@mips.com: Rewrite commit message.]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19489/
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

Enable CONFIG_SPI_GPIO in ci20_defconfig, in order to make use of the
spi-gpio driver in a further commit.

[paul.burton@mips.com: Rewrite commit message.]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19488/
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

All Octeons starting with Octeon II have RAPIDIO controller which
can function even with PCI disabled.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Alexandre Bounine <alex.bou9@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19988/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Porter <mporter@kernel.crashing.org>

Introduce the same option as PPC and ARM already have because
RAPIDIO can function in the absence of PCI.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Alexandre Bounine <alex.bou9@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19987/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Porter <mporter@kernel.crashing.org>

This is necessary to be able to include <linux/msi.h> when
CONFIG_GENERIC_MSI_IRQ_DOMAIN is enabled. Without this, a build with
CONFIG_GENERIC_MSI_IRQ_DOMAIN fails with:

   In file included from include/linux/kvm_host.h:20:0,
                    from arch/mips/kernel/asm-offsets.c:24:
>> include/linux/msi.h:197:10: fatal error: asm/msi.h: No such file or directory
    #include <asm/msi.h>
             ^~~~~~~~~~~
   compilation terminated.
   make[2]: *** [arch/mips/kernel/asm-offsets.s] Error 1
   make[2]: Target '__build' not remade because of errors.
   make[1]: *** [prepare0] Error 2
   make[1]: Target 'prepare' not remade because of errors.
   make: *** [sub-make] Error 2
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19986/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Hanna Hawa <hannah@marvell.com>

Defines CP0_CONFIG3, CP0_CONFIG6, CP0_PAGEGRAIN and use them in
kernel-entry-init.h for Loongson64.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19264/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>

Loongson-3A R3.1 is the bugfix revision of Loongson-3A R3.

All Loongson-3 CPU family:

Code-name         Brand-name       PRId
Loongson-3A R1    Loongson-3A1000  0x6305
Loongson-3A R2    Loongson-3A2000  0x6308
Loongson-3A R3    Loongson-3A3000  0x6309
Loongson-3A R3.1  Loongson-3A3000  0x630d
Loongson-3B R1    Loongson-3B1000  0x6306
Loongson-3B R2    Loongson-3B1500  0x6307
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19263/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>

Having the zload address at 0x8060.0000 means the size of the
uncompressed kernel cannot be bigger than around 6 MiB, as it is
deflated at address 0x8001.0000.

This limit is too small; a kernel with some built-in drivers and things
like debugfs enabled will already be over 6 MiB in size, and so will
fail to extract properly.

To fix this, we bump the zload address from 0x8060.0000 to 0x8100.0000.

This is fine, as all the boards featuring Ingenic JZ SoCs have at least
32 MiB of RAM, and use u-boot or compatible bootloaders which won't
hardcode the load address but read it from the uImage's header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19787/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

Instead of using dma_alloc_coherent() and memset() directly use
dma_zalloc_coherent().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19962/
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: dev@kresin.me

Linux expects that if a CPU modifies a memory location, then that
modification will eventually become visible to other CPUs in the system.

Loongson 3 CPUs include a Store Fill Buffer (SFB) which sits between a
core & its L1 data cache, queueing memory accesses & allowing for faster
forwarding of data from pending stores to younger loads from the core.
Unfortunately the SFB prioritizes loads such that a continuous stream of
loads may cause a pending write to be buffered indefinitely. This is
problematic if we end up with 2 CPUs which each perform a store that the
other polls for - one or both CPUs may end up with their stores buffered
in the SFB, never reaching cache due to the continuous reads from the
poll loop. Such a deadlock condition has been observed whilst running
qspinlock code.

This patch changes the definition of cpu_relax() to smp_mb() for
Loongson-3, forcing a flush of the SFB on SMP systems which will cause
any pending writes to make it as far as the L1 caches where they will
become visible to other CPUs. If the kernel is not compiled for SMP
support, this will expand to a barrier() as before.

This workaround matches that currently implemented for ARM when
CONFIG_ARM_ERRATA_754327=y, which was introduced by commit 534be1d5
("ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore").

Although the workaround is only required when the Loongson 3 SFB
functionality is enabled, and we only began explicitly enabling that
functionality in v4.7 with commit 1e820da3 ("MIPS: Loongson-3:
Introduce CONFIG_LOONGSON3_ENHANCEMENT"), existing or future firmware
may enable the SFB which means we may need the workaround backported to
earlier kernels too.

[paul.burton@mips.com:
  - Reword commit message & comment.
  - Limit stable backport to v3.15+ where we support Loongson 3 CPUs.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: 534be1d5 ("ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore")
References: 1e820da3 ("MIPS: Loongson-3: Introduce CONFIG_LOONGSON3_ENHANCEMENT")
Patchwork: https://patchwork.linux-mips.org/patch/19830/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
Cc: stable@vger.kernel.org # v3.15+

This macro substitution is the shortcut to map cacheable IO memory
with coherent and write-back attributes. Since it is entirely unused
by kernel, lets just remove it.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/19937/
CC: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sinan Kaya <okaya@codeaurora.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Sergey.Semin@t-platforms.ru
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org