- 03 Dec, 2015 1 commit
-
-
Nikita Kiryanov authored
Add basic support for SBC-T43: a CM-T43 based single board computer. CM-T43 is an AM437x based System-on-Module designed to serve as a building block in embedded applications. SBC-T43 is composed of CM-T43 module on top of the SB-SOM-T43 baseboard. Basic support includes UART, GPIO, and I2C. Signed-off-by:
Nikita Kiryanov <nikita@compulab.co.il> Acked-by:
Rob Herring <robh@kernel.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Benoit Cousson <bcousson@baylibre.com> Cc: Rob Herring <robh@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
- 01 Dec, 2015 2 commits
-
-
Vignesh R authored
Uart1 rxd is wakeup capable on DRA72 EVM. Hence, mark rxd line as wakeup capable. This is similar to commit 66b04369 ("ARM: dts: dra7-evm: Mark uart1 rxd as wakeup capable") for DRA74 EVM. Signed-off-by:
Vignesh R <vigneshr@ti.com> Acked-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Mugunthan V N authored
Set the alias for qspi to spi0 Signed-off-by:
Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by:
Tom Rini <trini@konsulko.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
- 30 Nov, 2015 37 commits
-
-
Mugunthan V N authored
Set the alias for qspi to spi0 Signed-off-by:
Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by:
Tom Rini <trini@konsulko.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Heiko Schocher authored
add support for the am335x based shc board. UART: 0-2 and 4 DRAM: 512 MiB MMC: OMAP SD/MMC: 0 @ 26 MHz OMAP SD/MMC: 1 @ 26 MHz I2C: at24 eeprom, pcf8563 USB: USB1 (host) Signed-off-by:
Heiko Schocher <hs@denx.de> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Franklin S Cooper Jr authored
Add device tree entry for the error location module. Signed-off-by:
Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Heiko Schocher authored
remove tps65217.dtsi and adapt all boards, which used it. Signed-off-by:
Heiko Schocher <hs@denx.de> Tested-by:
Keerthy <j-keerthy@ti.com> Acked-by:
Mark Brown <broonie@kernel.org> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Ilya Ledvich authored
Add pinmux configuration for ECAP0 pin. Add node for PWM backlight device. Use PWM output from ecap0 as backlight source. Signed-off-by:
Ilya Ledvich <ilya@compulab.co.il> Signed-off-by:
Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by:
Igor Grinberg <grinberg@compulab.co.il> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Ilya Ledvich authored
Add pinmux configurations for RGMII1 based CPSW Ethernet pins and MDIO pins: - default configuration required for module in active state, - sleep configuration required for module in inactive state. Add mac node with single slave device. Add nodes for davinci_mdio and cpsw_emac0. Signed-off-by:
Ilya Ledvich <ilya@compulab.co.il> Signed-off-by:
Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by:
Igor Grinberg <grinberg@compulab.co.il> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Ilya Ledvich authored
Add pinmux configuration for MMC0 pins. Add fixed regulator 'vmmc_fixed'. Enable MMC0 in 4-bit mode. Signed-off-by:
Ilya Ledvich <ilya@compulab.co.il> Signed-off-by:
Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by:
Igor Grinberg <grinberg@compulab.co.il> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Ilya Ledvich authored
Add pinmux configuration for NAND specific GPMC pins. Add description for GPMC controller. Add child node for NAND flash including CM-T335 specific partition table to GPMC node. Enable error-location module (ELM). Acked-by:
Igor Grinberg <grinberg@compulab.co.il> Signed-off-by:
Ilya Ledvich <ilya@compulab.co.il> Signed-off-by:
Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Ilya Ledvich authored
Add pinmux configuration for I2C0 and I2C1 pins. Add description for I2C0 bus, set clock frequency to 400kHz. Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus. Signed-off-by:
Ilya Ledvich <ilya@compulab.co.il> Signed-off-by:
Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by:
Igor Grinberg <grinberg@compulab.co.il> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Ilya Ledvich authored
Add basic support for CompuLab cm-t335 module based on AM335X SoC. CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM) The module is built around the Texas Instruments Sitara AM3352/4 system-on-chip. The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit Ethernet, CAN bus. Current patch adds support: UART0 and GPIO LED Detailed description can be found at the module site: http://www.compulab.co.il/products/computer-on-modules/cm-t335/Signed-off-by:
Ilya Ledvich <ilya@compulab.co.il> [uri.mashiach@compulab.co.il: the default RAM amount reduced to 128MB to support also the minimal module configuration] Signed-off-by:
Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by:
Igor Grinberg <grinberg@compulab.co.il> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
The schematic expects VAUX1 to be 3.0V attached to the debug port. The schematic expects VAUX4 to be 1.8V. VAUX4 powers VDDS_CSI2 on processor. Signed-off-by:
Adam Ford <adam.ford@logicpd.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
When used with the Logic PD development kit, this makes the I2C buses match the BSP released by Logic PD. Signed-off-by:
Adam Ford <adam.ford@logicpd.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
Setup UART2 for communication at 3MBps with flow control. Signed-off-by:
Adam Ford <adam.ford@logicpd.com> [tony@atomide.com: dropped the kim changes, that binding has been removed] Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
The development kit schematic expects VAUX1 to be 3.0V. Most users use the development kit as a reference. The development kit schematic expects VAUX4 to be 1.8V. VAUX4 powers VDDS_CSI2 on processor. If the voltage is too high it could damage the processor. If it's too low, it won't work. Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
When used with the Logic PD development kit, this makes the I2C buses match the BSP released by Logic PD. Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
Use the TWL4030 Codec with mcbsp2 on Torpedo. Signed-off-by:
Adam Ford <adam.ford@logicpd.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Franklin S Cooper Jr authored
Add dma channel information to the gpmc. Although not enabled by default this will allow prefetch-dma to be used. Signed-off-by:
Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Neil Armstrong authored
Add dm816x DT entries for omap4-hwspinlock support as hwmod spinbox. Cc: Brian Hutchinson <b.hutchman@gmail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Neil Armstrong authored
Remove invalid l3_main hwmod entry from dm816x DT ocp node. Cc: Brian Hutchinson <b.hutchman@gmail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Neil Armstrong authored
Adds ti,timer-pwm property to timers 4 to 7 to permit usage of their PWM output fonctionnality via the dmtimer driver. Cc: Brian Hutchinson <b.hutchman@gmail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Andrew F. Davis authored
Using constants for pinctrl allows better readability and removes redundancy with comments. AM33XX_IOPAD allows us to use part of the pinctrl physical address as in the TRM instead of an offset. Signed-off-by:
Andrew F. Davis <afd@ti.com> Reviewed-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register as an offset from the padconf physical address instead of the offset from padconf base. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macro to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Use the pinmux IOPAD macros to define the register absolute physical address instead of the offset from the padconf base address. This makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-