Since mmap for userspace is based on page alignment, add page alignment
for iram alloc from pool, otherwise, some good data located in the same
page of dmab->area maybe touched wrongly by userspace like pulseaudio.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1608221747-3474-1-git-send-email-yibin.gong@nxp.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

This platform only supported iphone type headset.
It can't support Dell headset mode.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/b97e971978034bc9b772a08ec91265e8@realtek.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Acer TravelMate laptops P648/P658 series with codec ALC282 only have
one physical jack for headset but there's a confusing lineout pin on
NID 0x1b reported. Audio applications hence misunderstand that there
are a speaker and a lineout, and take the lineout as the default audio
output.

Add a new quirk to remove the useless lineout and enable the pin 0x18
for jack sensing and headset microphone.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201216125200.27053-1-chiu@endlessos.orgSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-v5.11' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Updates for v5.11

There's a lot of changes here but mostly cleanups and driver specific
things, the most user visible change is the support for boot time
selection of Intel DSP firmware which will make it easier for people to
move over to the preferred modern implementations in distros and other
large scale deployments.

This also includes a merge of the new auxillary bus which was done in
anticipation of use by the Intel DSP drivers which didn't quite make it.

 - Lots more cleanups and simplifications from Morimoto-san.
 - Support for some basic DPCM systems in the audio graph card from
   Sameer Pujar.
 - Remove some old pre-DT Freescale drivers for platforms that are now
   DT only.
 - Move selection of which Intel DSP implementation to use to boot time
   rather than requiring it to be selected at build time.
 - Support for Allwinner H6 I2S, Analog Devices ADAU1372, Intel
   Alderlake-S, GMediatek MT8192, NXP i.MX HDMI and XCVR, Realtek RT715,
   Qualcomm SM8250 and simple GPIO based muxes.

syzbot spotted a potential out-of-bounds shift in the PCM OSS layer
where it calculates the buffer size with the arbitrary shift value
given via an ioctl.

Add a range check for avoiding the undefined behavior.
As the value can be treated by a signed integer, the max shift should
be 30.

Reported-by: syzbot+df7dc146ebdd6435eea3@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209084552.17109-2-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

syzbot spotted a potential out-of-bounds shift in the USB-audio format
parser that receives the arbitrary shift value from the USB
descriptor.

Add a range check for avoiding the undefined behavior.

Reported-by: syzbot+df7dc146ebdd6435eea3@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209084552.17109-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add pre-dsp download initialization for the DAC's used in the surround
sound configuration. Fixes issues of no audio on surround channels.

Fixes: 2e492b8e ("ALSA: hda/ca0132 - Add ZxR init commands")
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201211225504.4508-2-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Add helper functions for the 8051 PLL PMU write verbs.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201211225504.4508-1-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge series "ASoC: SOF: Intel: fix to dsp state dump trace levels" from Kai Vehmanen <kai.vehmanen@linux.intel.com>:

Small series that addresses a problem where DSP status dump
for a failure case, ends up being printed as as debug print. This
is important information for any bug report. While at it, the series
contains a few cleanups to related code.

Ranjani Sridharan (3):
  ASoC: SOF: Intel: hda: remove duplicated status dump
  ASoC: SOF: modify the SOF_DBG flags
  ASoC: SOF: Intel: hda: fix the condition passed to sof_dev_dbg_or_err

 sound/soc/sof/debug.c            |  2 +-
 sound/soc/sof/intel/byt.c        |  2 +-
 sound/soc/sof/intel/hda-loader.c | 19 +++++++++++++------
 sound/soc/sof/intel/hda.c        | 10 ++++------
 sound/soc/sof/loader.c           |  4 ++--
 sound/soc/sof/ops.c              |  2 +-
 sound/soc/sof/sof-priv.h         | 13 ++++++++-----
 7 files changed, 30 insertions(+), 22 deletions(-)

--
2.29.2

Merge series "ASoC: rt1015p: delay 300ms for waiting calibration" from Tzung-Bi Shih <tzungbi@google.com>:

The 1st patch moves SDB control from DAI ops trigger to DAPM event
(per review comments in v1).

The 2nd patch adds the 300ms delay for waiting calibration.

Changes from v2:
- Use gpiod_set_value_cansleep() instead of gpiod_set_value().
(https://patchwork.kernel.org/project/alsa-devel/patch/20201210033617.79300-2-tzungbi@google.com/)
- Assuming the calibration state gets lost after system suspend.
(https://patchwork.kernel.org/project/alsa-devel/patch/20201210033617.79300-3-tzungbi@google.com/)

Changes from v1:
(https://patchwork.kernel.org/project/alsa-devel/patch/20201209033742.3825973-1-tzungbi@google.com/)
- Move the delay from trigger to DAPM event.

Tzung-Bi Shih (2):
  ASoC: rt1015p: move SDB control from trigger to DAPM
  ASoC: rt1015p: delay 300ms after SDB pulling high for calibration

 sound/soc/codecs/rt1015p.c | 69 ++++++++++++++++++--------------------
 1 file changed, 32 insertions(+), 37 deletions(-)

--
2.29.2.684.gfbc64c5ab5-goog

The check for infoframe transmit status in hdmi_infoframe_uptodate()
makes the assumption that packet buffer index is set to zero.

Align code with specification and explicitly set the index before
AC_VERB_GET_HDMI_DIP_XMIT. The packet index setting affects both
DIP-Data and DIP-XmitCtrl verbs.

There are no known cases where the old implementation has caused driver
to work incorrectly. This change is purely based on code review against
the specification (HDA spec rev1.0a).
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211131613.3271407-1-kai.vehmanen@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Add missing parameters to avoid W=1 error
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211102255.3189589-1-kai.vehmanen@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This has a goto followed by an unreachable return statement.  The goto
is correct because it cleans up so the current runtime behavior is fine.
Let's delete the unreachable return statement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X9NFg3KVm16Gx6Io@mwandaSigned-off-by: Mark Brown <broonie@kernel.org>

Adds PM ops to machine drivers so that they notify components in the
sound card when system suspend.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201211051334.2313899-1-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

Dan reported that smatch reports wrong size check and after analysis it
is confirmed that we are comparing wrong value: pointer size instead of
array size. However the check itself is problematic as in UAPI header
there are two fields:

struct snd_soc_tplg_enum_control {
    (...)
    char texts[SND_SOC_TPLG_NUM_TEXTS][SNDRV_CTL_ELEM_ID_NAME_MAXLEN];
    __le32 values[SND_SOC_TPLG_NUM_TEXTS * SNDRV_CTL_ELEM_ID_NAME_MAXLEN / 4];

the texts field is for names and the values one for values assigned to
those named fields, after analysis it becomes clear that there is quite
a lot overhead values than we may possibly name. So instead of changing
check to ARRAY_SIZE(ec->values), as it was first suggested, use
hardcoded value of SND_SOC_TPLG_NUM_TEXTS.

Link: https://lore.kernel.org/alsa-devel/X9B0eDcKy+9B6kZl@mwanda/Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201210152541.191728-1-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When we parse "values" we perform check if there is correct number of
them. However similar check is missing in case of "texts", add it.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201210152541.191728-2-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The condition boot_iteration == HDA_FW_BOOT_ATTEMPTS to determine
the log level for the DSP status dump would only work in the case of DSP
init failure after maximum number of attempts to initialize the DSP. If
DSP init succeeds in less than HDA_FW_BOOT_ATTEMPTS attempts and FW
loading fails, the ROM status dump would end up getting logged as debug
instead of an error.

So, add a new flag, SOF_DBG_DUMP_LOG_ERROR, to explicitly specify
the log level for DSP status dump.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211100743.3188821-4-kai.vehmanen@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The SOF_DBG_* macros are used for dual purposes right now, for the
sof_core_debug module parameter and for the dbg_dump() ops. So, separate
these two types of flags into different types to avoid confusion.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211100743.3188821-3-kai.vehmanen@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove the duplicate status dump in case DSP init fails. The core will
be powered down in this case and the status dump will be invalid anyway.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211100743.3188821-2-kai.vehmanen@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

RT1015p needs 300ms delay after SDB pulling high for internal
calibration during the power on sequence.

Delays 300ms right before data sends out to avoid data truncated.

Assuming the calibration state gets lost after system suspend.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201211051224.2307349-3-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

Moves SDB control from DAI ops trigger to DAPM.  As long as BCLK
and LRCLK are ready, SDB can be toggled earlier.

Changes from using gpiod_set_value() to gpiod_set_value_cansleep()
because it executes in non-atomic context.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201211051224.2307349-2-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

The error handling frees "ctl" but it's still on the "dsp->ctl_list"
list so that could result in a use after free.  Remove it from the list
before returning.

Fixes: 2323736d ("ASoC: wm_adsp: Add basic support for rev 1 firmware file format")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/X9B0keV/02wrx9Xs@mwandaSigned-off-by: Mark Brown <broonie@kernel.org>

The current channel-map control implementation in USB-audio driver may
lead to an error message like
  "control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set.  It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.

This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().

Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The debug prints from patch_hdmi.c are not aligned with HDA common code
in hda_codec.c nor with other HDA codec drivers.

To align with rest of the codebase, use hexadecimal formatting whenever
printing value of a HDA NID. Also refer to NIDs with capital letters in
traces as is done other modules. This presentation is also aligned with
the formatting used in HDA codec procfs entry.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211124547.3243871-1-kai.vehmanen@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Add supported for more Lenovo ALC285 Headset Button.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/bb1f1da1526d460885aa4257be81eb94@realtek.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Now that the DSP's audio configuration is understood, remove previous
hacky methods of trying to properly configure it.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-6-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Make sure that the DSP has no DMA channels allocated once the firmware
is downloaded, and that the default audio streams in use by the DSP are
setup in the correct order.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-5-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Add functions for both reading and writing to the 8051's exram. Also,
add a little bit of documentation on how the addresses are segmented.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-4-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Add function for remapping a ChipIO stream's ports. Also include some
documentation as to how this works.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-3-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Reset the codec upon initialization to clear out anything that may have
been setup on a previous boot into Windows, or in case of an improper
shutdown.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-2-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

A problem exists in enabling silent stream when connection type is
DisplayPort. Silent stream programming is completed when a new DP
receiver is connected, but infoframe transmission does not actually
start until PCM is opened for the first time. This can result in audible
gap of multiple seconds. This only affects the first PCM open.

Fix the issue by properly assigning a converter to the silent stream,
and modifying the required stream ID programming sequence.

This change only affects Intel display audio codecs.

BugLink: https://github.com/thesofproject/linux/issues/2468
Fixes: 951894cf ("ALSA: hda/hdmi: Add Intel silent stream support")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201210174445.3134104-1-kai.vehmanen@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Change the Input Source enumerated control's strings to make it play
nice with pulseaudio.

Fixes: 7cb9d94c ("ALSA: hda/ca0132: add alt_select_in/out for R3Di + SBZ")
Cc: <stable@kernel.org>
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201208195223.424753-2-conmanx360@gmail.com
Link: https://lore.kernel.org/r/20201210173550.2968-2-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The Windows driver sets the pincfg for the AE-5's rear-headphone to
report as a microphone. This causes issues with Pulseaudio mistakenly
believing there is no headphone plugged in. In Linux, we should instead
set it to be a headphone.

Fixes: a6b0961b ("ALSA: hda/ca0132 - fix AE-5 pincfg")
Cc: <stable@kernel.org>
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201208195223.424753-1-conmanx360@gmail.com
Link: https://lore.kernel.org/r/20201210173550.2968-1-conmanx360@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Steinberg UR22 (with USB ID 0499:1509) requires the implicit feedback
for the proper playback, otherwise it causes occasional cracks.
This patch adds the corresponding the quirk table entry with the
recently added generic implicit fb support.
Reported-and-tested-by: Kilian <meschi@posteo.de>
Link: https://lore.kernel.org/r/20201209161835.13625-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

It seems that the HD-audio clear and reconfig sysfs don't work any
longer after the recent driver core change.  There are multiple issues
around that: the linked list corruption and the dead device handling.
The former issue is fixed by another patch for the driver core itself,
while the latter patch needs to be addressed in HD-audio side.

This patch corresponds to the latter, it recovers those broken
functions by replacing the device detach and attach actions with the
standard core API functions, which are almost equivalent with unbind
and bind actions.

Fixes: 65488832 ("driver core: Avoid binding drivers to dead devices")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209207
Link: https://lore.kernel.org/r/20201209150119.7705-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Document the missing properties which are currently required for
Tegra186/Tegra194 DT files.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1607006202-4078-3-git-send-email-spujar@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>