To summarize the issue observed in error cases:

SW Flow: For i2c message transfer, packet header and data payload is
posted and then required error/packet completion interrupts are enabled
later.

HW flow: HW process the packet just after packet header is posted, if
ARB lost/NACK error occurs (SW will not handle immediately when error
happens as error interrupts are not enabled at this point). HW assumes
error is acknowledged and clears current data in FIFO, But SW here posts
the remaining data payload which still stays in FIFO as stale data
(data without packet header).

Now once the interrupts are enabled, SW handles ARB lost/NACK error by
clearing the ARB lost/NACK interrupt. Now HW assumes that SW attended
the error and will parse/process stale data (data without packet header)
present in FIFO which causes invalid NACK errors.

Fix: Enable the error interrupts before posting the packet into FIFO
which make sure HW to not clear the fifo. Also disable the packet mode
before acknowledging errors (ARB lost/NACK error) to not process any
stale data. As error interrupts are enabled before posting the packet
header use spinlock to avoid preempting.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use readl_poll_timeout_atomic() function as *wait_for_config_load()
function can be called from interrupt context.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Define separate function for configuration load register handling
to make it use by different functions later.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

During i2c controller initialization, when fifo flush fails return error
instead of returning the error during exit.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

After CONFIG_LOAD register is programmed instead of explicitly waiting
for timeout, use readl_poll_timeout() to check for register value to get
updated or wait till timeout.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

"i2c-sh_mobile" is used on sh7343, sh7366, sh7722, sh7723, and sh7724
only. As all of the above select ARCH_SHMOBILE, restrict its driver
dependencies from SUPERH to ARCH_SHMOBILE.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

It's better to have strings in the code like they appeared in the output.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This makes it trivial to constify them, so do that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

On Tegra124/132 the pins for I2C6 are shared with the Display Port AUX
(DPAUX) channel and on Tegra210 the pins for I2C4 and I2C6 are shared
with DPAUX1 and DPAUX0, respectively. The multiplexing of the pins is
handled by a register in the DPAUX and so the Tegra DPAUX driver has
been updated to register a pinctrl device for managing these pins.

The pins for these particular I2C devices are bound to the I2C device
prior to probing. However, these I2C devices are in a different power
partition to the DPAUX devices that own the pins. Hence, it is desirable
to place the pins in the 'idle' state and allow the DPAUX power
partition to switch off, when these I2C devices is not in use.
Therefore, add calls to place the I2C pins in the 'default' and 'idle'
states when the I2C device is runtime resumed and suspended,
respectively.

Please note that the pinctrl functions that set the state of the pins
check to see if the devices has pins associated and will return zero
if they do not. Therefore, it is safe to call these pinctrl functions
even for I2C devices that do not have any pins associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Update the Tegra I2C driver to use runtime PM and move the code in the
tegra_i2c_clock_enable/disable() functions to the PM runtime resume and
suspend callbacks, respectively.

Note that given that CONFIG_PM is not mandatory for Tegra, if CONFIG_PM
is not enabled and so runtime PM is not enabled, ensure that the I2C
clocks are turned on during probe and kept on by calling the resume
callback directly.

In the function tegra_i2c_init(), the variable 'err' does not need to be
initialised to zero in tegra_i2c_init() because it is initialised when
pm_runtime_get_sync() is called. Furthermore, to ensure we only return 0
from tegra_i2c_init(), it is necessary to re-initialise 'err' to 0 after
a successful call to pm_runtime_get_sync() because it can return a
positive value on success. However, alternatively re-initialise 'err' by
using the return value of the function tegra_i2c_flush_fifos() because
it can only be 0 or -ETIMEDOUT.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The I2C adapter is unlocked regardless of whether the tegra_i2c_init()
called during the resume is successful or not. However, if the
tegra_i2c_init() is not successful, then ->is_suspended is not set to
false. Simplify the resume code by only setting ->is_suspended to false
if tegra_i2c_init() is successful and return the error code from
tegra_i2c_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

All Tegra I2C devices have the name "Tegra I2C adapter" which is not
very useful when viewing the I2C adapter names via the sysfs. Therefore,
use the device name, which is unique for each I2C device, instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Tegra has only supported device-tree for platform/board configuration
for quite some time now and so simplify the Tegra I2C driver by dropping
code for non device-tree platforms/boards.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add missing new line characters for the various error messages.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Checkpatch warns about missing blank lines after declarations in the
Tegra I2C driver and so fix these.

Note that the initialisation of 'val' to zero in tegra_dvc_init() is
unnecessary and so remove this.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Checkpatch warns about spacing around the '<<' operator in the Tegra I2C
driver and so fix these by converting the bit definitions that are using
this operator to use the BIT macro.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Checkpatch warns about some lines over 80 characters in the Tegra I2C
driver and so fix these.

While we are at it, prefix the second instance of "STOP condition" in
the comment with a "the".
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Disabling the adapter after each transfer adds additional delays
for each I2C transfer. Even if we don't wait for it to be disabled
anymore, on next transfer we will need to if we have several transfers
in a row.

Now during the transfer init we check if IC_TAR can be changed
dynamically, the status register for no activity and TX buffer being
empty. In this case we don't need to disable it

When a transfer fails the adapter will still be disabled - this is a
conservative approach. When transfers succeed, the adapter is left
enabled and it's configured so to disable interrupts.

Alternating register reads on 2 slaves:
perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00

Before:
	8.638705161 seconds time elapsed                  ( +-  5.90% )
After:
	7.516821591 seconds time elapsed                  ( +-  0.11% )
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This adapter can be synthesized with dynamic tar update enabled or disabled.
When enabled it is not necessary to disable the adapter to change the slave
address in some situations, which saves some time per transaction.

There is no direct register to know if this feature is enabled but we can do it
indirectly by writing to the 10BIT_ADDR field in IC_CON: this field is
read only when dynamic tar update is enabled.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

These are used in 2 places and will be needed in more.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If we aren't going to continue using the controller we can just disable
it instead of waiting for it to complete. The biggest improvement here
is when a I2C transaction is completed and it doesn't block until
the adapter is disabled. When a new transfer is needed we will disable
and wait for its completion.

This way the adapter will continue changing its state in parallel to the
execution of the thread that requested the I2C transaction saving most
of the time 25~250 usec per I2C transaction.

A simple program doing a register read (1 byte write, 1 byte read)
alternating on 2 different slaves repeated 25k times for each and
measurements taken 4 times we get:

perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00

Before:
	30.879317977 seconds time elapsed                 ( +- 14.83% )
After:
	8.638705161 seconds time elapsed                  ( +-  5.90% )
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fast mode is the default speed of i2c-designware which can be overridden
by platform data or by "clock-frequency" device property. Even though
the ACPI 5.1 can pass device properties via _DSD method, shipping systems
define the connection speed between I2C host and each slave in their
I2cSerialBus resources. Which means speed is not defined per bus but per
slave.

As there is now support in i2c-core to find the bus speed from ACPI use
that to set up the bus speed prior registering the I2C adapter.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

ACPI 5 specification doesn't have property for the I2C bus speed but
I2cSerialBus resource descriptor which define each controller-slave
connection define the maximum speed supported by that connection.

Thus finding the maximum safe speed for the bus is to walk through all
I2cSerialBus resources that are associated to I2C controller and use the
speed of slowest connection.

Add function i2c_acpi_find_bus_speed() to the i2c-core that adapter
drivers can call prior registering itself to core.

This implies two-step walk through the I2cSerialBus resources: call to
i2c_acpi_find_bus_speed() does the first scan and finds the safe bus
speed that adapter drivers can set up. Adapter driver registration does
the second scan when i2c-core creates the I2C slaves by calling the
i2c_acpi_register_devices(). In that way the bus speed is set in case
slave device probe gets called during registration and does communication.

Previous version commit 55d38d06 ("i2c: core: Add function for finding
the bus speed from ACPI") got reverted due merge conflicts from
commit 525e6fab ("i2c / ACPI: add support for ACPI reconfigure
notifications").

This version is a bit bigger than previous version but is still sharing
the lowest and complicated part of I2cSerialBus lookup routines with the
existing code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I2C ACPI enumeration was originally implemented in another module under
drivers/acpi/ but was later moved into i2c-core with added support for
I2C ACPI operation region.

Rename these acpi_i2c_ prefixed functions, structures and defines in
i2c-core to i2c_acpi_ in order to have more consistent name space.

This is updated version from commit a7003b65 ("i2c: core: Cleanup I2C
ACPI namespace") that got reverted due merge conflicts from
commit 525e6fab ("i2c / ACPI: add support for ACPI reconfigure
notifications").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch enabled high speed mode. High speed mode can be turn on by
setting the clk_freq to 3400000. High speed HCNT and LCNT are needed
as there is no default value provided.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

DW_IC_CON_MASTER, DW_IC_CON_SLAVE_DISABLE and DW_IC_CON_RESTART_EN are
common config that need to be set for i2c designware master. So, configure
it first without having to repeat inside the if else.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch enabled fast mode plus. The fast mode plus and fast speed
share the same HCNT and LCNT register. So, the fast mode plus will only
run when the HCNT and LCNT value is provided. Else, it will run at fast
speed as default.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I2C designware controller can run at fast mode plus and high speed. This
patch adds the capability to get the HCNT, LCNT configuration via
FPCN (fast plus) and HSCN (high speed) ACPI method.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I2c designware controller operate speed is configured in the register
IC_CON. Previously the operate speed is determined by a local variable
clk_freq. This patch will move the local variable clk_freq into struct
dw_i2c_dev. This change will ease the set and get of the clk_freq.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The i2c Octeon and ThunderX drivers are maintained by Cavium.
While at it fix the whitespace errors of the next entry.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Initialize booleon values with true instead of 1.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Sort include files alphabetically to reduce probability of merge
conflicts.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The register offsets are different between Octeon and ThunderX so move
them into the algorithm struct and get rid of the define.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add SMBUS alert interrupt support. For now only device tree is
supported for specifying the alert. In case of ACPI an error
is returned.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The ThunderX SOC uses the same i2c block as the Octeon SOC.
The main difference is that on ThunderX the device is a PCI device
so device probing is done via PCI, interrupts are MSI-X. The
clock rates can be set via device tree or ACPI.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Move common functionality into a separate file in preparation of the
re-use from the ThunderX i2c driver.

Functions are slightly re-ordered but no other changes are included.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This is an intermediate commit in preparation of the driver split.
The module rename in this commit will be reverted in the next patch,
this is just done to make the series bisectible.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.

Keep a direct pointer to the chip description instead of an index into
the chip description array.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>

No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>