LAB and IBB regulators can be current-limited by setting the
appropriate registers, but this operation is granted only after
sending an unlock code for secure access.

Besides the secure access, it would be possible to use the
regmap helper for get_current_limit, as there is no security
blocking reads, but I chose not to as to avoid having a very
big array containing current limits, especially for IBB.

That said, these regulators support current limiting for:
- LAB (pos): 200-1600mA, with 200mA per step (8 steps),
- IBB (neg):   0-1550mA, with  50mA per step (32 steps).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-3-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The LAB and IBB regulator have just one range and it is useless
to use linear_range ops, as these are used to express multiple
linear ranges.

Switch list_voltage and map_voltage callbacks to *_linear instead.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-2-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "Really implement Qualcomm LAB/IBB regulators" from AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>:

Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.

In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.

With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.

Changes in v2:
 - From Mark Brown review:
   - Replaced some if branches with switch statements
   - Moved irq get and request in probe function
   - Changed short conditionals to full ones
   - Removed useless check for ocp_irq_requested
 -  Fixed issues with YAML documentation

AngeloGioacchino Del Regno (7):
  regulator: qcom-labibb: Implement voltage selector ops
  regulator: qcom-labibb: Implement current limiting
  regulator: qcom-labibb: Implement pull-down, softstart, active
    discharge
  dt-bindings: regulator: qcom-labibb: Document soft start properties
  regulator: qcom-labibb: Implement short-circuit and over-current IRQs
  dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
  arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP

 .../regulator/qcom-labibb-regulator.yaml      |  30 +-
 arch/arm64/boot/dts/qcom/pmi8998.dtsi         |   8 +-
 drivers/regulator/qcom-labibb-regulator.c     | 661 +++++++++++++++++-
 3 files changed, 686 insertions(+), 13 deletions(-)

--
2.29.2

Implement {get,set}_voltage_sel, list_voltage, map_voltage with
the useful regulator regmap helpers in order to be able to manage
the voltage of LAB (positive) and IBB (negative) regulators.

In particular, the supported ranges are the following:
- LAB (pos):  4600mV to  6100mV with 100mV stepping,
- IBB (neg): -7700mV to -1400mV with 100mV stepping.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210113194214.522238-2-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fix the ternary condition which is a bad coding style
in the kernel

I also remove the defering configuration of the nxp,phase-shift.
The configuration is now done at parsing time. It save some memory
and it's better for comprehension.

I also use the OTP default configuration when the parameter is wrong
or not specified.
I think that it's better to use the default configuration from the chip
than an arbitrary value.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-7-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use a linear range to describe the voltages of the
bucks 1-6 instead of listing it one by one (via a macro)
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-6-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.

As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-5-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.

As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-4-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

nxp,phase-shift is an enum so use enum format to describe it.
Minimum and maximum values are also wrong.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210114174714.122561-3-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

pf8x00 module build was not documented.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20210114174714.122561-2-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The platform data header was only used to pass platform
data from board files. We now populate the regulators
exclusively from device tree, so the header contents can
be moved into the regulator drivers.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-2-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The struct ab8500_regulator_platform_data was a leftover
since the days before we probed all regulators from the
device tree. The ab8500-ext regulator was the only used,
defining platform data and register intialization that
was never used for anything, a copy of a boardfile no
longer in use.

Delete the ab8500_regulator_platform_data and make the
ab8500-ext regulator reference the regulator init data
in the local file directly. We are 100% device tree
these days.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Search for <ncurses.h> in the default header path of HOSTCC

 - Tweak the option order to be kind to old BSD awk

 - Remove 'kvmconfig' and 'xenconfig' shorthands

 - Fix documentation

* tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  Documentation: kbuild: Fix section reference
  kconfig: remove 'kvmconfig' and 'xenconfig' shorthands
  lib/raid6: Let $(UNROLL) rules work with macOS userland
  kconfig: Support building mconf with vendor sysroot ncurses
  kconfig: config script: add a little user help
  MAINTAINERS: adjust GCC PLUGINS after gcc-plugin.sh removal

Pull SCSI fixes from James Bottomley:
 "This is two driver fixes (megaraid_sas and hisi_sas).

  The megaraid one is a revert of a previous revert of a cpu hotplug fix
  which exposed a bug in the block layer which has been fixed in this
  merge window.

  The hisi_sas performance enhancement comes from switching to interrupt
  managed completion queues, which depended on the addition of
  devm_platform_get_irqs_affinity() which is now upstream via the irq
  tree in the last merge window"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: hisi_sas: Expose HW queues for v2 hw
  Revert "Revert "scsi: megaraid_sas: Added support for shared host tagset for cpuhotplug""

Pull block fixes from Jens Axboe:

 - Missing CRC32 selections (Arnd)

 - Fix for a merge window regression with bdev inode init (Christoph)

 - bcache fixes

 - rnbd fixes

 - NVMe pull request from Christoph:
    - fix a race in the nvme-tcp send code (Sagi Grimberg)
    - fix a list corruption in an nvme-rdma error path (Israel Rukshin)
    - avoid a possible double fetch in nvme-pci (Lalithambika Krishnakumar)
    - add the susystem NQN quirk for a Samsung driver (Gopal Tiwari)
    - fix two compiler warnings in nvme-fcloop (James Smart)
    - don't call sleeping functions from irq context in nvme-fc (James Smart)
    - remove an unused argument (Max Gurtovoy)
    - remove unused exports (Minwoo Im)

 - Use-after-free fix for partition iteration (Ming)

 - Missing blk-mq debugfs flag annotation (John)

 - Bdev freeze regression fix (Satya)

 - blk-iocost NULL pointer deref fix (Tejun)

* tag 'block-5.11-2021-01-10' of git://git.kernel.dk/linux-block: (26 commits)
  bcache: set bcache device into read-only mode for BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET
  bcache: introduce BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE for large bucket
  bcache: check unsupported feature sets for bcache register
  bcache: fix typo from SUUP to SUPP in features.h
  bcache: set pdev_set_uuid before scond loop iteration
  blk-mq-debugfs: Add decode for BLK_MQ_F_TAG_HCTX_SHARED
  block/rnbd-clt: avoid module unload race with close confirmation
  block/rnbd: Adding name to the Contributors List
  block/rnbd-clt: Fix sg table use after free
  block/rnbd-srv: Fix use after free in rnbd_srv_sess_dev_force_close
  block/rnbd: Select SG_POOL for RNBD_CLIENT
  block: pre-initialize struct block_device in bdev_alloc_inode
  fs: Fix freeze_bdev()/thaw_bdev() accounting of bd_fsfreeze_sb
  nvme: remove the unused status argument from nvme_trace_bio_complete
  nvmet-rdma: Fix list_del corruption on queue establishment failure
  nvme: unexport functions with no external caller
  nvme: avoid possible double fetch in handling CQE
  nvme-tcp: Fix possible race of io_work and direct send
  nvme-pci: mark Samsung PM1725a as IGNORE_DEV_SUBNQN
  nvme-fcloop: Fix sscanf type and list_first_entry_or_null warnings
  ...

Pull io_uring fixes from Jens Axboe:
 "A bit larger than I had hoped at this point, but it's all changes that
  will be directed towards stable anyway. In detail:

   - Fix a merge window regression on error return (Matthew)

   - Remove useless variable declaration/assignment (Ye Bin)

   - IOPOLL fixes (Pavel)

   - Exit and cancelation fixes (Pavel)

   - fasync lockdep complaint fix (Pavel)

   - Ensure SQPOLL is synchronized with creator life time (Pavel)"

* tag 'io_uring-5.11-2021-01-10' of git://git.kernel.dk/linux-block:
  io_uring: stop SQPOLL submit on creator's death
  io_uring: add warn_once for io_uring_flush()
  io_uring: inline io_uring_attempt_task_drop()
  io_uring: io_rw_reissue lockdep annotations
  io_uring: synchronise ev_posted() with waitqueues
  io_uring: dont kill fasync under completion_lock
  io_uring: trigger eventfd for IOPOLL
  io_uring: Fix return value from alloc_fixed_file_ref_node
  io_uring: Delete useless variable ‘id’ in io_prep_async_work
  io_uring: cancel more aggressively in exit_work
  io_uring: drop file refs after task cancel
  io_uring: patch up IOPOLL overflow_flush sync
  io_uring: synchronise IOPOLL on task_submit fail

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 5.11-rc3.

  Include in here are:

   - USB gadget driver fixes for reported issues

   - new usb-serial driver ids

   - dma from stack bugfixes

   - typec bugfixes

   - dwc3 bugfixes

   - xhci driver bugfixes

   - other small misc usb driver bugfixes

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
  usb: dwc3: gadget: Clear wait flag on dequeue
  usb: typec: Send uevent for num_altmodes update
  usb: typec: Fix copy paste error for NVIDIA alt-mode description
  usb: gadget: enable super speed plus
  kcov, usb: hide in_serving_softirq checks in __usb_hcd_giveback_urb
  usb: uas: Add PNY USB Portable SSD to unusual_uas
  usb: gadget: configfs: Preserve function ordering after bind failure
  usb: gadget: select CONFIG_CRC32
  usb: gadget: core: change the comment for usb_gadget_connect
  usb: gadget: configfs: Fix use-after-free issue with udc_name
  usb: dwc3: gadget: Restart DWC3 gadget when enabling pullup
  usb: usbip: vhci_hcd: protect shift size
  USB: usblp: fix DMA to stack
  USB: serial: iuu_phoenix: fix DMA from stack
  USB: serial: option: add LongSung M5710 module support
  USB: serial: option: add Quectel EM160R-GL
  USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug
  usb: gadget: f_uac2: reset wMaxPacketSize
  usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression
  usb: dwc3: ulpi: Replace CPU-based busyloop with Protocol-based one
  ...

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for 5.11-rc3. Nothing major,
  just resolving some reported issues:

   - cleanup some remaining mentions of the ION drivers that were
     removed in 5.11-rc1

   - comedi driver bugfix

   - two error path memory leak fixes

  All have been in linux-next for a while with no reported issues"

* tag 'staging-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: ION: remove some references to CONFIG_ION
  staging: mt7621-dma: Fix a resource leak in an error handling path
  Staging: comedi: Return -EFAULT if copy_to_user() fails
  staging: spmi: hisi-spmi-controller: Fix some error handling paths

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.11-rc3.

  The majority here are fixes for the habanalabs drivers, but also in
  here are:

   - crypto driver fix

   - pvpanic driver fix

   - updated font file

   - interconnect driver fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (26 commits)
  Fonts: font_ter16x32: Update font with new upstream Terminus release
  misc: pvpanic: Check devm_ioport_map() for NULL
  speakup: Add github repository URL and bug tracker
  MAINTAINERS: Update Georgi's email address
  crypto: asym_tpm: correct zero out potential secrets
  habanalabs: Fix memleak in hl_device_reset
  interconnect: imx8mq: Use icc_sync_state
  interconnect: imx: Remove a useless test
  interconnect: imx: Add a missing of_node_put after of_device_is_available
  interconnect: qcom: fix rpmh link failures
  habanalabs: fix order of status check
  habanalabs: register to pci shutdown callback
  habanalabs: add validation cs counter, fix misplaced counters
  habanalabs/gaudi: retry loading TPC f/w on -EINTR
  habanalabs: adjust pci controller init to new firmware
  habanalabs: update comment in hl_boot_if.h
  habanalabs/gaudi: enhance reset message
  habanalabs: full FW hard reset support
  habanalabs/gaudi: disable CGM at HW initialization
  habanalabs: Revise comment to align with mirror list name
  ...

Section 3.11 was incorrectly called 3.9, fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Pull ARC fixes from Vineet Gupta:

 - Address the 2nd boot failure due to snafu in signal handling code
   (first was generic console ttynull issue)

 - misc other fixes

* tag 'arc-5.11-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [hsdk]: Enable FPU_SAVE_RESTORE
  ARC: unbork 5.11 bootup: fix snafu in _TIF_NOTIFY_SIGNAL handling
  include/soc: remove headers for EZChip NPS
  arch/arc: add copy_user_page() to <asm/page.h> to fix build error on ARC

Pull powerpc fixes from Michael Ellerman:

 - A fix for machine check handling with VMAP stack on 32-bit.

 - A clang build fix.

Thanks to Christophe Leroy and Nathan Chancellor.

* tag 'powerpc-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Handle .text.{hot,unlikely}.* in linker script
  powerpc/32s: Fix RTAS machine check with VMAP stack

Pull x86 fixes from Borislav Petkov:
 "As expected, fixes started trickling in after the holidays so here is
  the accumulated pile of x86 fixes for 5.11:

   - A fix for fanotify_mark() missing the conversion of x86_32 native
     syscalls which take 64-bit arguments to the compat handlers due to
     former having a general compat handler. (Brian Gerst)

   - Add a forgotten pmd page destructor call to pud_free_pmd_page()
     where a pmd page is freed. (Dan Williams)

   - Make IN/OUT insns with an u8 immediate port operand handling for
     SEV-ES guests more precise by using only the single port byte and
     not the whole s32 value of the insn decoder. (Peter Gonda)

   - Correct a straddling end range check before returning the proper
     MTRR type, when the end address is the same as top of memory.
     (Ying-Tsun Huang)

   - Change PQR_ASSOC MSR update scheme when moving a task to a resctrl
     resource group to avoid significant performance overhead with some
     resctrl workloads. (Fenghua Yu)

   - Avoid the actual task move overhead when the task is already in the
     resource group. (Fenghua Yu)"

* tag 'x86_urgent_for_v5.11_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/resctrl: Don't move a task to the same resource group
  x86/resctrl: Use an IPI instead of task_work_add() to update PQR_ASSOC MSR
  x86/mtrr: Correct the range check before performing MTRR type lookups
  x86/sev-es: Fix SEV-ES OUT/IN immediate opcode vc handling
  x86/mm: Fix leak of pmd ptlock
  fanotify: Fix sys_fanotify_mark() on native x86-32

Merge tag 'hwmon-for-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Fix possible KASAN issue in amd_energy driver

 - Avoid configuration problem in pwm-fan driver

 - Fix kernel-doc warning in sbtsi_temp documentation

* tag 'hwmon-for-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (amd_energy) fix allocation of hwmon_channel_info config
  hwmon: (pwm-fan) Ensure that calculation doesn't discard big period values
  hwmon: (sbtsi_temp) Fix Documenation kernel-doc warning

Pull dmaengine fixes from Vinod Koul:
 "A bunch of dmaengine driver fixes for:

   - coverity discovered issues for xilinx driver

   - qcom, gpi driver fix for undefined bhaviour and one off cleanup

   - update Peter's email for TI DMA drivers

   - one-off for idxd driver

   - resource leak fix for mediatek and milbeaut drivers"

* tag 'dmaengine-fix-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
  dmaengine: stm32-mdma: fix STM32_MDMA_VERY_HIGH_PRIORITY value
  dmaengine: xilinx_dma: fix mixed_enum_type coverity warning
  dmaengine: xilinx_dma: fix incompatible param warning in _child_probe()
  dmaengine: xilinx_dma: check dma_async_device_register return value
  dmaengine: qcom: fix gpi undefined behavior
  dt-bindings: dma: ti: Update maintainer and author information
  MAINTAINERS: Add entry for Texas Instruments DMA drivers
  qcom: bam_dma: Delete useless kfree code
  dmaengine: dw-edma: Fix use after free in dw_edma_alloc_chunk()
  dmaengine: milbeaut-xdmac: Fix a resource leak in the error handling path of the probe function
  dmaengine: mediatek: mtk-hsdma: Fix a resource leak in the error handling path of the probe function
  dmaengine: qcom: gpi: Fixes a format mismatch
  dmaengine: idxd: off by one in cleanup code
  dmaengine: ti: k3-udma: Fix pktdma rchan TPL level setup

Pull i2c fixes from Wolfram Sang:
 "Three driver bugfixes for I2C. Buisness as usual"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mediatek: Fix apdma and i2c hand-shake timeout
  i2c: i801: Fix the i2c-mux gpiod_lookup_table not being properly terminated
  i2c: sprd: use a specific timeout to avoid system hang up issue

Change my email contact ahead of a likely painful eleven-month migration
to a certain cobalt enteprisey groupware cloud product that will totally
break my workflow.  Some day I may get used to having to email being
sequestered behind both claret and cerulean oath2+sms 2fa layers, but
for now I'll stick with keying in one password to receive an email vs.
the required four.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When the creator of SQPOLL io_uring dies (i.e. sqo_task), we don't want
its internals like ->files and ->mm to be poked by the SQPOLL task, it
have never been nice and recently got racy. That can happen when the
owner undergoes destruction and SQPOLL tasks tries to submit new
requests in parallel, and so calls io_sq_thread_acquire*().

That patch halts SQPOLL submissions when sqo_task dies by introducing
sqo_dead flag. Once set, the SQPOLL task must not do any submission,
which is synchronised by uring_lock as well as the new flag.

The tricky part is to make sure that disabling always happens, that
means either the ring is discovered by creator's do_exit() -> cancel,
or if the final close() happens before it's done by the creator. The
last is guaranteed by the fact that for SQPOLL the creator task and only
it holds exactly one file note, so either it pins up to do_exit() or
removed by the creator on the final put in flush. (see comments in
uring_flush() around file->f_count == 2).

One more place that can trigger io_sq_thread_acquire_*() is
__io_req_task_submit(). Shoot off requests on sqo_dead there, even
though actually we don't need to. That's because cancellation of
sqo_task should wait for the request before going any further.

note 1: io_disable_sqo_submit() does io_ring_set_wakeup_flag() so the
caller would enter the ring to get an error, but it still doesn't
guarantee that the flag won't be cleared.

note 2: if final __userspace__ close happens not from the creator
task, the file note will pin the ring until the task dies.

Fixed: b1b6b5a3 ("kernel/io_uring: cancel io_uring before task works")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

files_cancel() should cancel all relevant requests and drop file notes,
so we should never have file notes after that, including on-exit fput
and flush. Add a WARN_ONCE to be sure.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

A simple preparation change inlining io_uring_attempt_task_drop() into
io_uring_flush().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We expect io_rw_reissue() to take place only during submission with
uring_lock held. Add a lockdep annotation to check that invariant.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

If BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET is set in incompat feature
set, it means the cache device is created with obsoleted layout with
obso_bucket_site_hi. Now bcache does not support this feature bit, a new
BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE incompat feature bit is added
for a better layout to support large bucket size.

For the legacy compatibility purpose, if a cache device created with
obsoleted BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit, all bcache
devices attached to this cache set should be set to read-only. Then the
dirty data can be written back to backing device before re-create the
cache device with BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE feature bit
by the latest bcache-tools.

This patch checks BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit
when running a cache set and attach a bcache device to the cache set. If
this bit is set,
- When run a cache set, print an error kernel message to indicate all
  following attached bcache device will be read-only.
- When attach a bcache device, print an error kernel message to indicate
  the attached bcache device will be read-only, and ask users to update
  to latest bcache-tools.

Such change is only for cache device whose bucket size >= 32MB, this is
for the zoned SSD and almost nobody uses such large bucket size at this
moment. If you don't explicit set a large bucket size for a zoned SSD,
such change is totally transparent to your bcache device.

Fixes: ffa47032 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

When large bucket feature was added, BCH_FEATURE_INCOMPAT_LARGE_BUCKET
was introduced into the incompat feature set. It used bucket_size_hi
(which was added at the tail of struct cache_sb_disk) to extend current
16bit bucket size to 32bit with existing bucket_size in struct
cache_sb_disk.

This is not a good idea, there are two obvious problems,
- Bucket size is always value power of 2, if store log2(bucket size) in
  existing bucket_size of struct cache_sb_disk, it is unnecessary to add
  bucket_size_hi.
- Macro csum_set() assumes d[SB_JOURNAL_BUCKETS] is the last member in
  struct cache_sb_disk, bucket_size_hi was added after d[] which makes
  csum_set calculate an unexpected super block checksum.

To fix the above problems, this patch introduces a new incompat feature
bit BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE, when this bit is set, it
means bucket_size in struct cache_sb_disk stores the order of power-of-2
bucket size value. When user specifies a bucket size larger than 32768
sectors, BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE will be set to
incompat feature set, and bucket_size stores log2(bucket size) more
than store the real bucket size value.

The obsoleted BCH_FEATURE_INCOMPAT_LARGE_BUCKET won't be used anymore,
it is renamed to BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET and still only
recognized by kernel driver for legacy compatible purpose. The previous
bucket_size_hi is renmaed to obso_bucket_size_hi in struct cache_sb_disk
and not used in bcache-tools anymore.

For cache device created with BCH_FEATURE_INCOMPAT_LARGE_BUCKET feature,
bcache-tools and kernel driver still recognize the feature string and
display it as "obso_large_bucket".

With this change, the unnecessary extra space extend of bcache on-disk
super block can be avoided, and csum_set() may generate expected check
sum as well.

Fixes: ffa47032 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This patch adds the check for features which is incompatible for
current supported feature sets.

Now if the bcache device created by bcache-tools has features that
current kernel doesn't support, read_super() will fail with error
messoage. E.g. if an unsupported incompatible feature detected,
bcache register will fail with dmesg "bcache: register_bcache() error :
Unsupported incompatible feature found".

Fixes: d721a43f ("bcache: increase super block version for cache device and backing device")
Fixes: ffa47032 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This patch fixes the following typos,
from BCH_FEATURE_COMPAT_SUUP to BCH_FEATURE_COMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_INCOMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_RO_COMPAT_SUPP

Fixes: d721a43f ("bcache: increase super block version for cache device and backing device")
Fixes: ffa47032 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There is no need to reassign pdev_set_uuid in the second loop iteration,
so move it to the place before second loop.
Signed-off-by: Yi Li <yili@winhong.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull zonefs fix from Damien Le Moal:
 "A single patch from Arnd to fix a missing dependency in zonefs
  Kconfig"

* tag 'zonefs-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: select CONFIG_CRC32

Merge tag 'linux-kselftest-kunit-fixes-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kunit fixes from Shuah Khan:
 "One fix to force the use of the 'tty' console for UML.

  Given that kunit tool requires the console output, explicitly stating
  the dependency makes sense than relying on it being the default"

* tag 'linux-kselftest-kunit-fixes-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: tool: Force the use of the 'tty' console for UML