With the latest mainline u-boot bootloader (v2012.10), timers (5-8) in
the ABE power domain are failing to turn-on. The timers never come out
of the disabled state when setting the module-mode field to enable.

The problem was exposed when u-boot was updated to NOT configure and
lock the ABE DPLL on start-up. If the ABE DPLL is configured and locked
by u-boot the problem does not occur. However, if the ABE DPLL is in the
idle low-power bypass state and we attempt to enable a timer in the ABE
power domain, it remains stuck in the disabled state. It appears to be a
problem the timer interface clock as this comes from the ABE DPLL.

If we place the ABE DPLL in the MN-bypass state and not the idle
low-power state, then this problem is not seen.

This problem only appears to occur on OMAP4460 and not OMAP4430.

Workaround this problem by locking the ABE DPLL for OMAP4460 in the
kernel on boot. By locking the ABE DPLL, when clocks from the ABE DPLL
are not being requested the DPLL will transition into a low-power stop
mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can
be enabled or disabled in addition to the standard configurable
multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X
multiplier is accounted for by checking to see whether it is enabled or
not. However, when calculating a new rate we only check to see if the
rate can be achieved with the current setting for the 4X multiplier.
Enhance the round_rate() function for such DPLLs to see if the rate
can be achieved with the 4X multiplier if it cannot be achieved without
the 4X multiplier.

This change is necessary, because when using the 32kHz clock as the
source clock for the ABE DPLL, the default DPLL frequency for the ABE
DPLL cannot be achieved without enabling the 4X multiplier.

When using the 32kHz clock as the source clock for the ABE DPLL and
attempting to lock the DPLL to 98.304MHz (default frequency), it was
found that the DPLL would fail to lock if the low-power mode for the DPLL
was not enabled. From reviewing boot-loader settings that configure the
ABE DPLL it was found that the low-power mode is enabled when using the
32kHz clock source, however, the documentation for OMAP does not state
that this is a requirement. Therefore, introduce a new function for
OMAP4 devices to see if low-power mode can be enabled when calculating a
new rate to ensure the DPLL will lock.

New variables for the last calculated 4X multiplier and low-power
setting have been added to the dpll data structure as well as variables
defining the bit mask for enabling these features via the DPLL's
control_reg. It is possible that we could eliminate these bit masks from
the dpll data structure as these bit masks are not unique to OMAP4, if
it is preferred.

The function omap3_noncore_program_dpll() has been updated to avoid
passing the calculated values for the multiplier (M) and divider (N) as
these are stored in the clk structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Currently all OMAP4 non-core DPLLs use the same function table for
configuring DPLLs. For these DPLLs, the function
omap4_dpll_regm4xen_recalc() is used to recalculate the DPLL rate and
the function omap4_dpll_regm4xen_round_rate() is used to calculate the
closest rate to that requested. However, these omap4_dpll_regm4xen_xxx()
functions are only applicable to the ABE DPLL and not the other non-core
DPLLs. Therefore, add a new function table for non-core DPLLs that do
not include the 4X-multiplier (M4X).

Please note that using these omap4_dpll_regm4x_xxx() function works for
the non-M4X DPLLs today because we only check to see if the 4X
multiplier is enabled when calculating the rate. However, it is planned
that the dpll functions will be enhanced to enable the 4X multiplier as
necessary (in order to achieve the requested rate) and so calling these
functions for non-M4X dplls will no longer work.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Commit "ARM: dts: OMAP4: Update timer addresses" updated the device-tree
names of the OMAP4 timers 5-7 because the default address for the timers
was changed from the L3 address to the MPU private address. When booting
with device-tree, this introduces a regression when attempting to set
the parent clock of timers 5-7 to the sys_clk_div_ck. Therefore, update
the clock aliases for timer 5-7 to reflect the updated device-tree name
for the timers.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply after the CCF conversion]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Pull x86 UAPI disintegration from David Howells.

This is the scripted disintegration of the uapi headers for x86, now
that most of the x86 updates for 3.8 are hopefully merged.

* tag 'disintegrate-x86-20121214' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate arch/x86/include/asm

Pull another devicetree update from Grant Likely:
 "Here's a couple more devicetree changes that I missed in the first
  pull by putting the tag in the wrong place.

  Two minor devicetree fixups for v3.8.  Addition of dummy inlines and
  constification of node argument to of_parse_phandle_with_args()."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  of: *node argument to of_parse_phandle_with_args should be const
  of/i2c: add dummy inline functions for when CONFIG_OF_I2C(_MODULE) isn't defined

Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
 "This is a branch with updates for Marvell's mvebu/kirkwood platforms.
  They came in late-ish, and were heavily interdependent such that it
  didn't make sense to split them up across the cross-platform topic
  branches.  So here they are (for the second release in a row) in a
  branch on their own."

* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
  arm: l2x0: add aurora related properties to OF binding
  arm: mvebu: add Aurora L2 Cache Controller to the DT
  arm: mvebu: add L2 cache support
  dma: mv_xor: fix error handling path
  dma: mv_xor: fix error checking of irq_of_parse_and_map()
  dma: mv_xor: use request_irq() instead of devm_request_irq()
  dma: mv_xor: clear the window override control registers
  arm: mvebu: fix address decoding armada_cfg_base() function
  ARM: mvebu: update defconfig with I2C and RTC support
  ARM: mvebu: Add SATA support for OpenBlocks AX3-4
  ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
  ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
  ARM: mvebu: Add support for I2C controllers in Armada 370/XP
  arm: mvebu: Add hardware I/O Coherency support
  arm: plat-orion: Add coherency attribute when setup mbus target
  arm: dma mapping: Export a dma ops function arm_dma_set_mask
  arm: mvebu: Add SMP support for Armada XP
  arm: mm: Add support for PJ4B cpu and init routines
  arm: mvebu: Add IPI support via doorbells
  arm: mvebu: Add initial support for power managmement service unit
  ...

Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
 "This branch contains device-tree updates for the SPEAr platform.  They
  had dependencies on earlier branches from this merge window, which is
  why they were broken out in a separate branch."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
  ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
  ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
  ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
  ARM: SPEAr1310: Fix AUXDATA for compact flash controller
  ARM: SPEAr13xx: Remove fields not required for ssp controller
  ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
  ARM: SPEAr: DT: Update device nodes
  ARM: SPEAr: DT: add uart state to fix warning
  ARM: SPEAr: DT: Modify DT bindings for STMMAC
  ARM: SPEAr: DT: Fix existing DT support
  ARM: SPEAr: DT: Update partition info for MTD devices
  ARM: SPEAr: DT: Update pinctrl list
  ARM: SPEAr13xx: DT: Add spics gpio controller nodes

Pull ARM Soc updates, take 2, from Olof Johansson:
 "This is the second batch of SoC updates for the 3.8 merge window,
  containing parts that had dependencies on earlier branches such that
  we couldn't include them with the first branch.

  These are general updates for Samsung Exynos, Renesas/shmobile and a
  topic branch that adds SMP support to Altera's socfpga platform."

Fix up conflicts mostly as per Olof.

* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: EXYNOS: Clock settings for SATA and SATA PHY
  ARM: EXYNOS: Add ARM down clock support
  ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
  ARM: EXYNOS: Add aliases for i2c controller
  ARM: EXYNOS: Setup legacy i2c controller interrupts
  sh: clkfwk: fixup unsed variable warning
  Revert "ARM: shmobile: r8a7779: Replace modify_scu_cpu_psr with scu_power_mode"
  Revert "ARM: shmobile: sh73a0: Replace modify_scu_cpu_psr with scu_power_mode"
  Revert "ARM: shmobile: emev2: Replace modify_scu_cpu_psr with scu_power_mode"
  ARM: highbank: use common debug_ll_io_init
  ARM: shmobile: sh7372: sh7372_fsiXck_clk become non-global
  ARM: shmobile: sh7372: remove fsidivx clock
  ARM: socfpga: mark secondary_trampoline as cpuinit
  socfpga: map uart into virtual address space so that early_printk() works
  ARM: socfpga: fix build break for allyesconfig
  ARM: socfpga: Enable SMP for socfpga
  ARM: EXYNOS: Add dp clock support for EXYNOS5
  ARM: SAMSUNG: call clk_get_rate for debugfs rate files
  ARM: SAMSUNG: add clock_tree debugfs file in clock

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>

Pull MIPS updates from Ralf Baechle:
 "The MIPS bits for 3.8.  This also includes a bunch fixes that were
  sitting in the linux-mips.org git tree for a long time.  This pull
  request contains updates to several OCTEON drivers and the board
  support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
  updates to the SSB bus support, MIPS kexec code and adds support for
  kdump.

  When pulling this, there are two expected merge conflicts in
  include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
  resolve, just remove the conflict markers and keep both alternatives."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
  MIPS: PMC-Sierra Yosemite: Remove support.
  VIDEO: Newport Fix console crashes
  MIPS: wrppmc: Fix build of PCI code.
  MIPS: IP22/IP28: Fix build of EISA code.
  MIPS: RB532: Fix build of prom code.
  MIPS: PowerTV: Fix build.
  MIPS: IP27: Correct fucked grammar in ops-bridge.c
  MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
  MIPS: Fix potencial corruption
  MIPS: Fix for warning from FPU emulation code
  MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
  MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
  MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
  MIPS: Remove unused smvp.h
  MIPS/EDAC: Improve OCTEON EDAC support.
  MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
  MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
  ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
  MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
  MIPS: Remove usage of CEVT_R4K_LIB config option.
  ...

Merging in the smp-on-socfpga branch into soc2 since the topics are similar
and it's a short branch in the first place.

* next/smp:
  ARM: socfpga: mark secondary_trampoline as cpuinit
  socfpga: map uart into virtual address space so that early_printk() works
  ARM: socfpga: fix build break for allyesconfig
  ARM: socfpga: Enable SMP for socfpga
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull x86 EFI update from Peter Anvin:
 "EFI tree, from Matt Fleming.  Most of the patches are the new efivarfs
  filesystem by Matt Garrett & co.  The balance are support for EFI
  wallclock in the absence of a hardware-specific driver, and various
  fixes and cleanups."

* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  efivarfs: Make efivarfs_fill_super() static
  x86, efi: Check table header length in efi_bgrt_init()
  efivarfs: Use query_variable_info() to limit kmalloc()
  efivarfs: Fix return value of efivarfs_file_write()
  efivarfs: Return a consistent error when efivarfs_get_inode() fails
  efivarfs: Make 'datasize' unsigned long
  efivarfs: Add unique magic number
  efivarfs: Replace magic number with sizeof(attributes)
  efivarfs: Return an error if we fail to read a variable
  efi: Clarify GUID length calculations
  efivarfs: Implement exclusive access for {get,set}_variable
  efivarfs: efivarfs_fill_super() ensure we clean up correctly on error
  efivarfs: efivarfs_fill_super() ensure we free our temporary name
  efivarfs: efivarfs_fill_super() fix inode reference counts
  efivarfs: efivarfs_create() ensure we drop our reference on inode on error
  efivarfs: efivarfs_file_read ensure we free data in error paths
  x86-64/efi: Use EFI to deal with platform wall clock (again)
  x86/kernel: remove tboot 1:1 page table creation code
  x86, efi: 1:1 pagetable mapping for virtual EFI calls
  x86, mm: Include the entire kernel memory map in trampoline_pgd
  ...

Pull x86 ACPI update from Peter Anvin:
 "This is a patchset which didn't make the last merge window.  It adds a
  debugging capability to feed ACPI tables via the initramfs.

  On a grander scope, it formalizes using the initramfs protocol for
  feeding arbitrary blobs which need to be accessed early to the kernel:
  they are fed first in the initramfs blob (lots of bootloaders can
  concatenate this at boot time, others can use a single file) in an
  uncompressed cpio archive using filenames starting with "kernel/".

  The ACPI maintainers requested that this patchset be fed via the x86
  tree rather than the ACPI tree as the footprint in the general x86
  code is much bigger than in the ACPI code proper."

* 'x86-acpi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  X86 ACPI: Use #ifdef not #if for CONFIG_X86 check
  ACPI: Fix build when disabled
  ACPI: Document ACPI table overriding via initrd
  ACPI: Create acpi_table_taint() function to avoid code duplication
  ACPI: Implement physical address table override
  ACPI: Store valid ACPI tables passed via early initrd in reserved memblock areas
  x86, acpi: Introduce x86 arch specific arch_reserve_mem_area() for e820 handling
  lib: Add early cpio decoder

Pull x86 RAS update from Ingo Molnar:
 "Rework all config variables used throughout the MCA code and collect
  them together into a mca_config struct.  This keeps them tightly and
  neatly packed together instead of spilled all over the place.

  Then, convert those which are used as booleans into real booleans and
  save some space.  These bits are exposed via
     /sys/devices/system/machinecheck/machinecheck*/"

* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, MCA: Finish mca_config conversion
  x86, MCA: Convert the next three variables batch
  x86, MCA: Convert rip_msr, mce_bootlog, monarch_timeout
  x86, MCA: Convert dont_log_ce, banks and tolerant
  drivers/base: Add a DEVICE_BOOL_ATTR macro

This reverts commit f269ae04.

It turns out it causes a very noticeable interactivity regression with
CONFIG_SCHED_AUTOGROUP (test-case: "make -j32" of the kernel in a
terminal window, while scrolling in a browser - the autogrouping means
that the two end up in separate cgroups, and the browser should be
smooth as silk despite the high load).

Says Paul Turner:
 "It seems that the update-throttling on the wake-side is reducing the
  interactive tasks' ability to preempt.  While I suspect the right
  longer term answer here is force these updates only in the
  cross-cgroup case; this is less trivial.  For this release I believe
  the right answer is either going to be a revert or restore the updates
  on the enqueue-side."
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Bisected-by: Mike Galbraith <efault@gmx.de>
Acked-by: Paul Turner <pjt@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull battery subsystem updates from Anton Vorontsov:
 "Highlights:

   - Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
     bq2415x_charger.  The drivers are a part of a solution to replace
     the proprietary Nokia BME stack

   - Power supply core now registers devices with a thermal cooling
     subsystem, so we can now automatically throttle charging.  Thanks
     to Ramakrishna Pallala!

   - Device tree support for ab8500 and max8925_power drivers

   - Random fixups and enhancements for a bunch of drivers."

* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
  max8925_power: Add support for device-tree initialization
  ab8500: Add devicetree support for chargalg
  ab8500: Add devicetree support for charger
  ab8500: Add devicetree support for btemp
  ab8500: Add devicetree support for fuelgauge
  twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
  jz4740-battery: Use devm_request_and_ioremap
  jz4740-battery: Use devm_kzalloc
  bq27x00_battery: Fixup nominal available capacity reporting
  bq2415x_charger: Fix style issues
  bq2415x_charger: Add Kconfig/Makefile entries
  power_supply: Add bq2415x charger driver
  power_supply: Add new Nokia RX-51 (N900) power supply battery driver
  max17042_battery: Fix missing verify_model_lock() return value check
  ds2782_battery: Fix signedness bug in ds278x_read_reg16()
  lp8788-charger: Fix ADC channel names
  lp8788-charger: Fix wrong ADC conversion
  lp8788-charger: Use consumer device name on setting IIO channels
  power_supply: Register power supply for thermal cooling device
  power_supply: Add support for CHARGE_CONTROL_* attributes
  ...

Pull media updates from Mauro Carvalho Chehab:

 - Missing MAINTAINERS entries were added for several drivers

 - Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
   sharing between V4L2 devices and GPU

 - Got rid of all warnings when compiling with W=1 on x86

 - Add a new driver for Exynos hardware (s3c-camif)

 - Several bug fixes, cleanups and driver improvements

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
  [media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
  [media] omap3isp: Prepare/unprepare clocks before/after enable/disable
  [media] omap3isp: preview: Add support for 8-bit formats at the sink pad
  [media] omap3isp: Replace printk with dev_*
  [media] omap3isp: Find source pad from external entity
  [media] omap3isp: Configure CSI-2 phy based on platform data
  [media] omap3isp: Add PHY routing configuration
  [media] omap3isp: Add CSI configuration registers from control block to ISP resources
  [media] omap3isp: Remove unneeded module memory address definitions
  [media] omap3isp: Use monotonic timestamps for statistics buffers
  [media] uvcvideo: Fix control value clamping for unsigned integer controls
  [media] uvcvideo: Mark first output terminal as default video node
  [media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
  [media] uvcvideo: Return -ENOTTY for unsupported ioctls
  [media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
  [media] uvcvideo: Don't fail when an unsupported format is requested
  [media] uvcvideo: Return -EACCES when trying to access a read/write-only control
  [media] uvcvideo: Set error_idx properly for extended controls API failures
  [media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
  [media] fc2580: write some registers conditionally
  ...

Pull first round of SCSI updates from James Bottomley:
 "This patch set includes two large new drivers: mpt3sas (for the next
  gen fusion SAS hardware) and csiostor a FCoE offload driver for the
  Chelsio converged network cards (this includes some net changes which
  I've OK'd with DaveM).

  The rest of the patch is driver updates (qla2xxx, lpfc, hptiop,
  be2iscsi) plus a few assorted updates and bug fixes.

  We also have a Power Management rework in the Upper Layer Drivers
  preparatory to doing ACPI zero power optical devices, but the actual
  enabler is still being worked on.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (72 commits)
  [SCSI] mpt3sas: add new driver supporting 12GB SAS
  [SCSI] scsi_transport_sas: add 12GB definitions for mpt3sas
  [SCSI] miscdevice: Adding support for MPT3SAS_MINOR(222)
  [SCSI] csiostor: remove unneeded memset()
  [SCSI] csiostor: Fix sparse warnings.
  [SCSI] qla2xxx: Display that driver is operating in legacy interrupt mode.
  [SCSI] qla2xxx: Dont clear drv active on iospace config failure.
  [SCSI] qla2xxx: Fix typo in qla2xxx driver.
  [SCSI] qla2xxx: Update ql2xextended_error_logging parameter description with new option.
  [SCSI] qla2xxx: Parameterize the link speed of hba rather than fcport.
  [SCSI] qla2xxx: Add 16Gb/s case to get port speed capability.
  [SCSI] qla2xxx: Move marking fcport online ahead of setting iiDMA speed.
  [SCSI] qla2xxx: Add acquiring of risc semaphore before doing ISP reset.
  [SCSI] qla2xxx: Ignore driver ack bit if corresponding presence bit is not set.
  [SCSI] qla2xxx: Fix typo in qla83xx_fw_dump function.
  [SCSI] qla2xxx: Add Gen3 PCIe speed 8GT/s to the log message.
  [SCSI] qla2xxx: Use correct Request-Q-Out register during bidirectional request processing
  [SCSI] qla2xxx: Move noisy Start scsi failed messages to verbose logging level.
  [SCSI] qla2xxx: Fix coccinelle warnings in qla2x00_relogin.
  [SCSI] qla2xxx: No fcport FC-4 type assignment in GA_NXT response.
  ...

Pull infiniband upate from Roland Dreier:
 "First batch of InfiniBand/RDMA changes for the 3.8 merge window:
   - A good chunk of Bart Van Assche's SRP fixes
   - UAPI disintegration from David Howells
   - mlx4 support for "64-byte CQE" hardware feature from Or Gerlitz
   - Other miscellaneous fixes"

Fix up trivial conflict in mellanox/mlx4 driver.

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (33 commits)
  RDMA/nes: Fix for crash when registering zero length MR for CQ
  RDMA/nes: Fix for terminate timer crash
  RDMA/nes: Fix for BUG_ON due to adding already-pending timer
  IB/srp: Allow SRP disconnect through sysfs
  srp_transport: Document sysfs attributes
  srp_transport: Simplify attribute initialization code
  srp_transport: Fix attribute registration
  IB/srp: Document sysfs attributes
  IB/srp: send disconnect request without waiting for CM timewait exit
  IB/srp: destroy and recreate QP and CQs when reconnecting
  IB/srp: Eliminate state SRP_TARGET_DEAD
  IB/srp: Introduce the helper function srp_remove_target()
  IB/srp: Suppress superfluous error messages
  IB/srp: Process all error completions
  IB/srp: Introduce srp_handle_qp_err()
  IB/srp: Simplify SCSI error handling
  IB/srp: Keep processing commands during host removal
  IB/srp: Eliminate state SRP_TARGET_CONNECTING
  IB/srp: Increase block layer timeout
  RDMA/cm: Change return value from find_gid_port()
  ...

Pull SPI updates from Grant Likely:
 "Primarily SPI device driver bug fixes, one removal of an old driver,
  and some new tegra support.  There is some core code change too, but
  all in all pretty small stuff.

  The new features to note are:
   - Common code for describing GPIO CS lines in the device tree
   - Remove the SPI_BUFSIZ limitation on spi_write_the_read()
   - core spi ensures bits_per_word is set correctly
   - SPARC can now use SPI"

* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (36 commits)
  spi/sparc: Allow of_register_spi_devices for sparc
  spi: Remove HOTPLUG section attributes
  spi: Add support for specifying 3-wire mode via device tree
  spi: Fix comparison of different integer types
  spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood driver.
  spi/sh: Add SH Mobile series as dependency to MSIOF controller
  spi/sh-msiof: Remove unneeded clock name
  spi: Remove SPI_BUFSIZ restriction on spi_write_then_read()
  spi/stmp: remove obsolete driver
  spi/clps711x: New SPI master driver
  spi: omap2-mcspi: remove duplicate inclusion of linux/err.h
  spi: omap2-mcspi: Fix the redifine warning
  spi/sh-hspi: add CS manual control support
  of_spi: add generic binding support to specify cs gpio
  spi: omap2-mcspi: remove duplicated include from spi-omap2-mcspi.c
  spi/bitbang: (cosmetic) simplify list manipulation
  spi/bitbang: avoid needless loop flow manipulations
  spi/omap: fix D0/D1 direction confusion
  spi: tegra: add spi driver for sflash controller
  spi: Dont call master->setup if not populated
  ...

Merge emailed autofs cleanup/fix patches from Ian Kent

* autofs:
  autofs4 - use simple_empty() for empty directory check
  autofs4 - dont clear DCACHE_NEED_AUTOMOUNT on rootless mount

For direct (and offset) mounts, if an automounted mount is manually
umounted the trigger mount dentry can appear non-empty causing it to
not trigger mounts. This can also happen if there is a file handle
leak in a user space automounting application.

This happens because, when a ioctl control file handle is opened
on the mount, a cursor dentry is created which causes list_empty()
to see the dentry as non-empty. Since there is a case where listing
the directory of these dentrys is needed, the use of dcache_dir_*()
functions for .open() and .release() is needed.

Consequently simple_empty() must be used instead of list_empty()
when checking for an empty directory.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The DCACHE_NEED_AUTOMOUNT flag is cleared on mount and set on expire
for autofs rootless multi-mount dentrys to prevent unnecessary calls
to ->d_automount().

Since DCACHE_MANAGE_TRANSIT is always set on autofs dentrys ->d_managed()
is always called so the check can be done in ->d_manage() without the
need to change the flag. This still avoids unnecessary calls to
->d_automount(), adds negligible overhead and eliminates a seriously
ugly check in the expire code.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ktest update from Steven Rostedt:
 "fixes and updated for new boot loaders"

* tag 'ktest-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Test if target machine is up before install
  ktest: Fix breakage from change of oldnoconfig to olddefconfig
  ktest: Add native support for syslinux boot loader
  ktest: Sync before reboot
  ktest: Add support for grub2

Pull KVM updates from Marcelo Tosatti:
 "Considerable KVM/PPC work, x86 kvmclock vsyscall support,
  IA32_TSC_ADJUST MSR emulation, amongst others."

Fix up trivial conflict in kernel/sched/core.c due to cross-cpu
migration notifier added next to rq migration call-back.

* tag 'kvm-3.8-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (156 commits)
  KVM: emulator: fix real mode segment checks in address linearization
  VMX: remove unneeded enable_unrestricted_guest check
  KVM: VMX: fix DPL during entry to protected mode
  x86/kexec: crash_vmclear_local_vmcss needs __rcu
  kvm: Fix irqfd resampler list walk
  KVM: VMX: provide the vmclear function and a bitmap to support VMCLEAR in kdump
  x86/kexec: VMCLEAR VMCSs loaded on all cpus if necessary
  KVM: MMU: optimize for set_spte
  KVM: PPC: booke: Get/set guest EPCR register using ONE_REG interface
  KVM: PPC: bookehv: Add EPCR support in mtspr/mfspr emulation
  KVM: PPC: bookehv: Add guest computation mode for irq delivery
  KVM: PPC: Make EPCR a valid field for booke64 and bookehv
  KVM: PPC: booke: Extend MAS2 EPN mask for 64-bit
  KVM: PPC: e500: Mask MAS2 EPN high 32-bits in 32/64 tlbwe emulation
  KVM: PPC: Mask ea's high 32-bits in 32/64 instr emulation
  KVM: PPC: e500: Add emulation helper for getting instruction ea
  KVM: PPC: bookehv64: Add support for interrupt handling
  KVM: PPC: bookehv: Remove GET_VCPU macro from exception handler
  KVM: PPC: booke: Fix get_tb() compile error on 64-bit
  KVM: PPC: e500: Silence bogus GCC warning in tlb code
  ...

Merge tag 'stable/for-linus-3.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen updates from Konrad Rzeszutek Wilk:
 - Add necessary infrastructure to make balloon driver work under ARM.
 - Add /dev/xen/privcmd interfaces to work with ARM and PVH.
 - Improve Xen PCIBack wild-card parsing.
 - Add Xen ACPI PAD (Processor Aggregator) support - so can offline/
   online sockets depending on the power consumption.
 - PVHVM + kexec = use an E820_RESV region for the shared region so we
   don't overwrite said region during kexec reboot.
 - Cleanups, compile fixes.

Fix up some trivial conflicts due to the balloon driver now working on
ARM, and there were changes next to the previous work-arounds that are
now gone.

* tag 'stable/for-linus-3.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/PVonHVM: fix compile warning in init_hvm_pv_info
  xen: arm: implement remap interfaces needed for privcmd mappings.
  xen: correctly use xen_pfn_t in remap_domain_mfn_range.
  xen: arm: enable balloon driver
  xen: balloon: allow PVMMU interfaces to be compiled out
  xen: privcmd: support autotranslated physmap guests.
  xen: add pages parameter to xen_remap_domain_mfn_range
  xen/acpi: Move the xen_running_on_version_or_later function.
  xen/xenbus: Remove duplicate inclusion of asm/xen/hypervisor.h
  xen/acpi: Fix compile error by missing decleration for xen_domain.
  xen/acpi: revert pad config check in xen_check_mwait
  xen/acpi: ACPI PAD driver
  xen-pciback: reject out of range inputs
  xen-pciback: simplify and tighten parsing of device IDs
  xen PVonHVM: use E820_Reserved area for shared_info

Pull s390 update from Martin Schwidefsky:
 "Add support to generate code for the latest machine zEC12, MOD and XOR
  instruction support for the BPF jit compiler, the dasd safe offline
  feature and the big one: the s390 architecture gets PCI support!!
  Right before the world ends on the 21st ;-)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits)
  s390/qdio: rename the misleading PCI flag of qdio devices
  s390/pci: remove obsolete email addresses
  s390/pci: speed up __iowrite64_copy by using pci store block insn
  s390/pci: enable NEED_DMA_MAP_STATE
  s390/pci: no msleep in potential IRQ context
  s390/pci: fix potential NULL pointer dereference in dma_free_seg_table()
  s390/pci: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
  s390/bpf,jit: add support for XOR instruction
  s390/bpf,jit: add support MOD instruction
  s390/cio: fix pgid reserved check
  vga: compile fix, disable vga for s390
  s390/pci: add PCI Kconfig options
  s390/pci: s390 specific PCI sysfs attributes
  s390/pci: PCI hotplug support via SCLP
  s390/pci: CHSC PCI support for error and availability events
  s390/pci: DMA support
  s390/pci: PCI adapter interrupts for MSI/MSI-X
  s390/bitops: find leftmost bit instruction support
  s390/pci: CLP interface
  s390/pci: base support
  ...

Pull m68k updates from Geert Uytterhoeven.

Fix up trivial conflict (m68k switched to generic version of
uapi/asm/socket.h, net tree updated the old one) as per Geert.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/sun3: Fix instruction faults
  m68k/sun3: Get interrupts working again
  m68k: move to a single instance of free_initmem()
  m68k: merge MMU and non-MMU versions of mm/init.c
  m68k: switch to using the asm-generic termios.h
  m68k: switch to using the asm-generic termbits.h
  m68k: switch to using the asm-generic sockios.h
  m68k: switch to using the asm-generic socket.h
  m68k: switch to using the asm-generic shmbuf.h
  m68k: switch to using the asm-generic sembuf.h
  m68k: switch to using the asm-generic msgbuf.h
  m68k: switch to using the asm-generic auxvec.h
  m68k: switch to using the asm-generic shmparam.h
  m68k: switch to using the asm-generic spinlock.h
  m68k: switch to using the asm-generic hw_irq.h
  arch/m68k: remove CONFIG_EXPERIMENTAL

Pull tiny sparc update from David Miller:
 "Not much going on this release cycle in sparc land, just a Kconfig
  tweak."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
  of_i2c: sparc: Allow OF_I2C for sparc

Pull networking fixes from David Miller:
 "A pile of fixes in response to yesterday's big merge.  The SCTP HMAC
  thing hasn't been addressed yet, I'll take care of that myself if Neil
  and Vlad don't show signs of life by tomorrow.

   1) Use after free of SKB in tuntap code.  Fix by Eric Dumazet,
      reported by Dave Jones.

   2) NFC LLCP code emits annoying kernel log message, triggerable by
      the user.  From Dave Jones.

   3) Fix several endianness bugs noticed by sparse in the bridging
      code, from Stephen Hemminger.

   4) Ipv6 NDISC code doesn't take padding into account properly, fix
      from YOSHIFUJI Hideaki.

   5) Add missing docs to ethtool_flow_ext struct, from Yan Burman."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  bridge: fix icmpv6 endian bug and other sparse warnings
  net: ethool: Document struct ethtool_flow_ext
  ndisc: Fix padding error in link-layer address option.
  tuntap: dont use skb after netif_rx_ni(skb)
  nfc: remove noisy message from llcp_sock_sendmsg

Merge misc VM changes from Andrew Morton:
 "The rest of most-of-MM.  The other MM bits await a slab merge.

  This patch includes the addition of a huge zero_page.  Not a
  performance boost but it an save large amounts of physical memory in
  some situations.

  Also a bunch of Fujitsu engineers are working on memory hotplug.
  Which, as it turns out, was badly broken.  About half of their patches
  are included here; the remainder are 3.8 material."

However, this merge disables CONFIG_MOVABLE_NODE, which was totally
broken.  We don't add new features with "default y", nor do we add
Kconfig questions that are incomprehensible to most people without any
help text.  Does the feature even make sense without compaction or
memory hotplug?

* akpm: (54 commits)
  mm/bootmem.c: remove unused wrapper function reserve_bootmem_generic()
  mm/memory.c: remove unused code from do_wp_page()
  asm-generic, mm: pgtable: consolidate zero page helpers
  mm/hugetlb.c: fix warning on freeing hwpoisoned hugepage
  hwpoison, hugetlbfs: fix RSS-counter warning
  hwpoison, hugetlbfs: fix "bad pmd" warning in unmapping hwpoisoned hugepage
  mm: protect against concurrent vma expansion
  memcg: do not check for mm in __mem_cgroup_count_vm_event
  tmpfs: support SEEK_DATA and SEEK_HOLE (reprise)
  mm: provide more accurate estimation of pages occupied by memmap
  fs/buffer.c: remove redundant initialization in alloc_page_buffers()
  fs/buffer.c: do not inline exported function
  writeback: fix a typo in comment
  mm: introduce new field "managed_pages" to struct zone
  mm, oom: remove statically defined arch functions of same name
  mm, oom: remove redundant sleep in pagefault oom handler
  mm, oom: cleanup pagefault oom handler
  memory_hotplug: allow online/offline memory to result movable node
  numa: add CONFIG_MOVABLE_NODE for movable-dedicated node
  mm, memcg: avoid unnecessary function call when memcg is disabled
  ...

Pull PCI update from Bjorn Helgaas:
 "Host bridge hotplug:
   - Untangle _PRT from struct pci_bus (Bjorn Helgaas)
   - Request _OSC control before scanning root bus (Taku Izumi)
   - Assign resources when adding host bridge (Yinghai Lu)
   - Remove root bus when removing host bridge (Yinghai Lu)
   - Remove _PRT during hot remove (Yinghai Lu)

  SRIOV
    - Add sysfs knobs to control numVFs (Don Dutile)

  Power management
   - Notify devices when power resource turned on (Huang Ying)

  Bug fixes
   - Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
   - Keep runtime PM enabled for unbound PCI devices (Huang Ying)
   - Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
   - Fix xen frontend shutdown issue (David Vrabel)
   - Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)

  Miscellaneous
   - Add GPL license for drivers/pci/ioapic (Andrew Cooks)
   - Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
   - NumaChip remote PCI support (Daniel Blueman)
   - Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
     Han)
   - Convert dev_printk() to dev_info(), etc (Joe Perches)
   - Add support for non PCI BAR ROM data (Matthew Garrett)
   - Add x86 support for host bridge translation offset (Mike Yoknis)
   - Report success only when every driver supports AER (Vijay
     Pandarathil)"

Fix up trivial conflicts.

* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
  PCI: Use phys_addr_t for physical ROM address
  x86/PCI: Add NumaChip remote PCI support
  ath9k: Use standard #defines for PCIe Capability ASPM fields
  iwlwifi: Use standard #defines for PCIe Capability ASPM fields
  iwlwifi: collapse wrapper for pcie_capability_read_word()
  iwlegacy: Use standard #defines for PCIe Capability ASPM fields
  iwlegacy: collapse wrapper for pcie_capability_read_word()
  cxgb3: Use standard #defines for PCIe Capability ASPM fields
  PCI: Add standard PCIe Capability Link ASPM field names
  PCI/portdrv: Use PCI Express Capability accessors
  PCI: Use standard PCIe Capability Link register field names
  x86: Use PCI setup data
  PCI: Add support for non-BAR ROMs
  PCI: Add pcibios_add_device
  EFI: Stash ROMs if they're not in the PCI BAR
  PCI: Add and use standard PCI-X Capability register names
  PCI/PM: Keep runtime PM enabled for unbound PCI devices
  xen-pcifront: Handle backend CLOSED without CLOSING
  PCI: SRIOV control and status via sysfs (documentation)
  PCI/AER: Report success only when every device has AER-aware driver
  ...

Pull regulator updates from Mark Brown:
 "A fairly quiet release again, a couple of relatively small new
  features and a bunch of driver specific work including yet more code
  elimination and fixes from Axel Lin.

   - Addidion of linear_min_sel for offsetting linear selectors in the
     helpers.
   - Support for continuous voltage ranges for regulators with extremely
     high resolution.
   - Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM
     vexpress."

Fix up trivial conflict (due to typo fix) in palmas-regulator.c

* tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (80 commits)
  regulator: core: Fix logic to determinate if regulator can change voltage
  regulator: s5m8767: Fix to work even if no DVS gpio present
  regulator: s5m8767: Fix to read the first DVS register.
  regulator: s5m8767: Fix to work when platform registers less regulators
  regulator: gpio-regulator: gpio_set_value should use cansleep
  regulator: gpio-regulator: Fix logical error in for() loop
  regulator: anatop: Use regulator_[get|set]_voltage_sel_regmap
  regulator: anatop: Use linear_min_sel with linear mapping
  regulator: max1586: Implement get_voltage_sel callback
  regulator: lp8788-buck: Kill _gpio_request function
  regulator: tps80031: Convert tps80031_ldo_ops to linear_min_sel and list_voltage_linear
  regulator: lp8788-ldo: Remove val array in lp8788_config_ldo_enable_mode
  regulator: gpio-regulator: Add ifdef CONFIG_OF guard for regulator_gpio_of_match
  regulator: palmas: Convert palmas_ops_smps to regulator_[get|set]_voltage_sel_regmap
  regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
  regulators: add regulator_can_change_voltage() function
  regulator: tps51632: Ensure [base|max]_voltage_uV pdata settings are valid
  regulator: wm831x-dcdc: Add MODULE_ALIAS for wm831x-boostp
  regulator: wm831x-dcdc: Ensure selected voltage falls within requested range
  regulator: tps51632: Use linear_min_sel and regulator_[map|list]_voltage_linear
  ...

Pull HID subsystem updates from Jiri Kosina:

 1) Support for HID over I2C bus has been added by Benjamin Tissoires.
    ACPI device discovery is still in the works.

 2) Support for Win8 Multitiouch protocol is being added, most work done
    by Benjamin Tissoires as well

 3) EIO/ERESTARTSYS is fixed in hiddev/hidraw, fixes by Andrew Duggan
    and Jiri Kosina

 4) ION iCade driver added by Bastien Nocera

 5) Support for a couple new Roccat devices has been added by Stefan
    Achatz

 6) HID sensor hubs are now auto-detected instead of having to list all
    the VID/PID combinations in the blacklist array

 7) other random fixes and support for new device IDs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (65 commits)
  HID: i2c-hid: add mutex protecting open/close race
  Revert "HID: sensors: add to special driver list"
  HID: sensors: autodetect USB HID sensor hubs
  HID: hidp: fallback to input session properly if hid is blacklisted
  HID: i2c-hid: fix ret_count check
  HID: i2c-hid: fix i2c_hid_get_raw_report count mismatches
  HID: i2c-hid: remove extra .irq field in struct i2c_hid
  HID: i2c-hid: reorder allocation/free of buffers
  HID: i2c-hid: fix memory corruption due to missing hid declaration
  HID: i2c-hid: remove superfluous include
  HID: i2c-hid: remove unneeded test in i2c_hid_remove
  HID: i2c-hid: i2c_hid_get_report may fail
  HID: i2c-hid: also call i2c_hid_free_buffers in i2c_hid_remove
  HID: i2c-hid: fix error messages
  HID: i2c-hid: fix return paths
  HID: i2c-hid: remove unused static declarations
  HID: i2c-hid: fix i2c_hid_dbg macro
  HID: i2c-hid: fix checkpatch.pl warning
  HID: i2c-hid: enhance Kconfig
  HID: i2c-hid: change I2C name
  ...

Pull trivial branch from Jiri Kosina:
 "Usual stuff -- comment/printk typo fixes, documentation updates, dead
  code elimination."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  HOWTO: fix double words typo
  x86 mtrr: fix comment typo in mtrr_bp_init
  propagate name change to comments in kernel source
  doc: Update the name of profiling based on sysfs
  treewide: Fix typos in various drivers
  treewide: Fix typos in various Kconfig
  wireless: mwifiex: Fix typo in wireless/mwifiex driver
  messages: i2o: Fix typo in messages/i2o
  scripts/kernel-doc: check that non-void fcts describe their return value
  Kernel-doc: Convention: Use a "Return" section to describe return values
  radeon: Fix typo and copy/paste error in comments
  doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
  various: Fix spelling of "asynchronous" in comments.
  Fix misspellings of "whether" in comments.
  eisa: Fix spelling of "asynchronous".
  various: Fix spelling of "registered" in comments.
  doc: fix quite a few typos within Documentation
  target: iscsi: fix comment typos in target/iscsi drivers
  treewide: fix typo of "suport" in various comments and Kconfig
  treewide: fix typo of "suppport" in various comments
  ...

Pull IEEE 1394 (FireWire) subsystem updates from Stefan Richter:
  - IPv4-over-1394: fixes for broadcast and multicast
  - SBP-2: allow thin-provisioning related commands
  - trivia

* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: net: remove unused variable in fwnet_receive_broadcast()
  firewire: net: Fix handling of fragmented multicast/broadcast packets.
  firewire: sbp2: allow WRITE SAME and REPORT SUPPORTED OPERATION CODES
  tools/firewire: nosy-dump: check for allocation failure

Pull sound updates from Takashi Iwai:
 "This update contains a fairly wide range of changes all over in sound
  subdirectory, mainly because of UAPI header moves by David and __dev*
  annotation removals by Bill.  Other highlights are:

   - Introduced the support for wallclock timestamps in ALSA PCM core

   - Add the poll loop implementation for HD-audio jack detection

   - Yet more VGA-switcheroo fixes for HD-audio

   - New VIA HD-audio codec support

   - More fixes on resource management in USB audio and MIDI drivers

   - More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
     Roland VG-99, etc

   - Add support for FastTrack C400 usb-audio

   - Clean ups in many drivers regarding firmware loading

   - Add PSC724 Ultiimate Edge support to ice1712

   - A few hdspm driver updates

   - New Stanton SCS.1d/1m FireWire driver

   - Standardisation of the logging in ASoC codes

   - DT and dmaengine support for ASoC Atmel

   - Support for Wolfson ADSP cores

   - New drivers for Freescale/iVeia P1022 and Maxim MAX98090

   - Lots of other ASoC driver fixes and developments"

Fix up trivial conflicts.  And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.

* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
  ALSA: hda - Move runtime PM check to runtime_idle callback
  ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
  ALSA: hda - Avoid doubly suspend after vga switcheroo
  ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
  ALSA: hda - Check validity of CORB/RIRB WP reads
  ALSA: hda - use usleep_range in link reset and change timeout check
  ALSA: HDA: VIA: Add support for codec VT1808.
  ALSA: HDA: VIA Add support for codec VT1705CF.
  ASoC: codecs: remove __dev* attributes
  ASoC: utils: remove __dev* attributes
  ASoC: ux500: remove __dev* attributes
  ASoC: txx9: remove __dev* attributes
  ASoC: tegra: remove __dev* attributes
  ASoC: spear: remove __dev* attributes
  ASoC: sh: remove __dev* attributes
  ASoC: s6000: remove __dev* attributes
  ASoC: OMAP: remove __dev* attributes
  ASoC: nuc900: remove __dev* attributes
  ASoC: mxs: remove __dev* attributes
  ASoC: kirkwood: remove __dev* attributes
  ...

Pull ARM SoC board updates, take 2 from Olof Johansson:
 "This branch contains board updates for shmobile that had dependencies
  on earlier branches past the first driver branch, and thus are merged
  separately.

  Most of these are to enable audio and USB on shmobile.  They contain a
  dependent ASoC branch that has been coordinated with Mark Brown."

* tag 'boards2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: shmobile: mackerel: Add FLCTL IRQ resource
  ARM: shmobile: use FSI driver's audio clock on ap4evb
  ARM: shmobile: use FSI driver's audio clock on mackerel
  ARM: shmobile: use FSI driver's audio clock on armadillo800eva
  ARM: shmobile: mackerel: enable DMAEngine on USB Host
  ARM: shmobile: marzen: add USB OHCI driver support
  ARM: shmobile: marzen: add USB EHCI driver support
  ARM: shmobile: marzen: add USB phy support
  ASoC: fsi: add master clock control functions
  ASoC: fsi: care fsi_hw_start/stop() return value
  ASoC: fsi: fsi_set_master_clk() was called from fsi_hw_xxx() only
  ASoC: fsi: use devm_request_irq()
  ASoC: fsi: fixup channels_min/max

Pull ARM SoC driver specific changes from Olof Johansson:
 "A collection of mostly SoC-specific driver updates:
   - a handful of pincontrol and setup changes
   - new drivers for hwmon and reset controller for vexpress
   - timing support updates for OMAP (gpmc and other interfaces)
   - plus a collection of smaller cleanups"

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: ux500: fix pin warning
  ARM: OMAP2+: tusb6010: generic timing calculation
  ARM: OMAP2+: smc91x: generic timing calculation
  ARM: OMAP2+: onenand: generic timing calculation
  ARM: OMAP2+: gpmc: generic timing calculation
  ARM: OMAP2+: gpmc: handle additional timings
  ARM: OMAP2+: nand: remove redundant rounding
  gpio: samsung: use pr_* instead of printk
  ARM: ux500: fixup magnetometer pins
  ARM: ux500: add STM pin configuration
  ARM: ux500: 8500: add pinctrl support for uart1 and uart2
  ARM: ux500: cosmetic fixups for uart0
  gpio: samsung: Fix input mode setting function for GPIO int
  ARM: SAMSUNG: Insert bitmap_gpio_int member in samsung_gpio_chip
  ARM: ux500: 8500: define SDI sleep states
  ARM: vexpress: Reset driver
  ARM: ux500: 8500: update SKE keypad pinctrl table
  hwmon: Versatile Express hwmon driver
  ARM: ux500: delete duplicate macro
  ARM: ux500: 8500: add IDLE pin configuration for SPI
  ...