Merge series from Maso Huang <maso.huang@mediatek.com>:

Add support for sample rate checking on the MT7986.

mt7986 only supports 8/12/16/24/32/48/96/192 kHz
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231024035019.11732-4-maso.huang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove the mt7986_wm8960_priv structure.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231024035019.11732-3-maso.huang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Drop the remove callback of mt7986_wm8960.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231024035019.11732-2-maso.huang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Variable d_len_code is being initialized to zero and then re-assigned a
different value in all the valid cases in the following switch statement.
The only place it is not being assigned a value is on the return for
a default case and in this case it does not need to be assigned. The
initialization is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20231023154917.671595-1-colin.i.king@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The driver is now built only when MACH_AMS_DELTA is selected, which
requires a very specific selection of ARCH settings.  As a consequence, it
gets very little attention from build-bots, if not none.

Drop the driver dependency on <asm/mach-types.h>, no longer required since
conversion to snd_soc_register_card() and drop of machine_is_ams_delta().
With that in place, allow the driver to be built in any environment as
long as COMPILE_TEST is selected.  Take care of not selecting
SND_SOC_OMAP_MCBSP if COMMON_CLK is not selected.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Link: https://lore.kernel.org/r/20231008135601.542356-1-jmkrzyszt@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Get fixes needed so we can enable build of ams-delta in more
configurations.

Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:

This is another series to convert ASoC drivers to use struct
platform_driver:remove_new(). The rockchip one was already send before
but with a wrong subject prefix, the cs42l43 driver is newer than the
last series. The remaining five patches are for driver combos that my
coccinelle patch failed to detect before.

Provide an option to load DSP data bin to ACP SRAM.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20231020062822.3913760-5-Vijendar.Mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

DSP data bin can be loaded in to ACP DRAM or ACP SRAM.
Add conditional check for ACP DRAM usage for data bin loading.
Rename DRAM base address macro to have symmetry.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20231020062822.3913760-4-Vijendar.Mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Increase DSP cache window range to 2.5MB to align with ACP memory.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20231020062822.3913760-3-Vijendar.Mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add SOF support for ACP6.3 version based platform
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20231020062822.3913760-2-Vijendar.Mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add acpi machine id for ACP6.3 version based platform and configure
driver data to enable SOF sound card support on newer boards.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20231020062822.3913760-1-Vijendar.Mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

I have a board (RK3588 based) that sets the sysclk to 12287999. The
es8328 driver fails to match this to the 12288000 rate and fails to
load. Allow the rate comparison to work if the frequency is within
100hz by dividing it by 100 and rounding it, then multiplying it back
by 100.

Note the 100hz value was chosen arbitrarily by me, but it has only
been tested with a 1hz difference.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231020171539.65513-1-macroalpha82@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Modify the value of max_register, otherwirse
the AW88261_EFRL1_REG register will not be
accessible.
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20231020083426.302925-3-wangweidong.a@awinic.comSigned-off-by: Mark Brown <broonie@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code.  However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

uniphier_aio_remove() returned zero unconditionally.  Make it return
void instead and convert all users to struct
platform_device::remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231013221945.1489203-16-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code.  However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

asoc_qcom_lpass_cpu_platform_remove() returned zero unconditionally.
Make it return void instead and convert all users to struct
platform_device::remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231013221945.1489203-15-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code.  However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

meson_card_remove() returned zero unconditionally. Make it return void
instead and convert all users to struct platform_device::remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20231013221945.1489203-14-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code.  However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

simple_util_remove() returned zero unconditionally. Make it return void
instead and convert all users to struct platform_device::remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20231013221945.1489203-13-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231013221945.1489203-12-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231013221945.1489203-11-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231013221945.1489203-10-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

Pull phy fixes from Vinod Koul:

 - mapphone-mdm6600 runtime pm & pinctrl handling fixes

 - Qualcomm qmp usb pcs register fixes, qmp pcie register size warning
   fix, m31 fixes for wrong pointer in PTR_ERR and dropping wrong vreg
   check, qmp combo fix for 8550 power config register

 - realtek usb fix for debugfs_create_dir() and kconfig dependency

* tag 'phy-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
  phy: realtek: Realtek PHYs should depend on ARCH_REALTEK
  phy: qualcomm: Fix typos in comments
  phy: qcom-qmp-combo: initialize PCS_USB registers
  phy: qcom-qmp-combo: Square out 8550 POWER_STATE_CONFIG1
  phy: qcom: m31: Remove unwanted qphy->vreg is NULL check
  phy: realtek: usb: Drop unnecessary error check for debugfs_create_dir()
  phy: qcom: phy-qcom-m31: change m31_ipq5332_regs to static
  phy: qcom: phy-qcom-m31: fix wrong pointer pass to PTR_ERR()
  dt-bindings: phy: qcom,ipq8074-qmp-pcie: fix warning regarding reg size
  phy: qcom-qmp-usb: split PCS_USB init table for sc8280xp and sa8775p
  phy: qcom-qmp-usb: initialize PCS_USB registers
  phy: mapphone-mdm6600: Fix pinctrl_pm handling for sleep pins
  phy: mapphone-mdm6600: Fix runtime PM for remove
  phy: mapphone-mdm6600: Fix runtime disable on probe

Pull EFI fixes from Ard Biesheuvel:
 "The boot_params pointer fix uses a somewhat ugly extern struct
  declaration but this will be cleaned up the next cycle.

   - don't try to print warnings to the console when it is no longer
     available

   - fix theoretical memory leak in SSDT override handling

   - make sure that the boot_params global variable is set before the
     KASLR code attempts to hash it for 'randomness'

   - avoid soft lockups in the memory acceptance code"

* tag 'efi-fixes-for-v6.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi/unaccepted: Fix soft lockups caused by parallel memory acceptance
  x86/boot: efistub: Assign global boot_params variable
  efi: fix memory leak in krealloc failure handling
  x86/efistub: Don't try to print after ExitBootService()

Pull powerpc fixes from Michael Ellerman:

 - Fix stale propagated yield_cpu in qspinlocks leading to lockups

 - Fix broken hugepages on some configs due to ARCH_FORCE_MAX_ORDER

 - Fix a spurious warning when copros are in use at exit time

Thanks to Nicholas Piggin, Christophe Leroy, Nysal Jan K.A Sachin Sant,
and Shrikanth Hegde.

* tag 'powerpc-6.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/qspinlock: Fix stale propagated yield_cpu
  powerpc/64s/radix: Don't warn on copros in radix__tlb_flush()
  powerpc/mm: Allow ARCH_FORCE_MAX_ORDER up to 12

Pull gpio fixes from Bartosz Golaszewski:

 - fix interrupt handling in suspend and wakeup in gpio-vf610

 - fix a bug on setting direction to output in gpio-vf610

 - add a missing memset() in gpio ACPI code

* tag 'gpio-fixes-for-v6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpiolib: acpi: Add missing memset(0) to acpi_get_gpiod_from_data()
  gpio: vf610: set value before the direction to avoid a glitch
  gpio: vf610: mask the gpio irq in system suspend and support wakeup

Pull rust fixes from Miguel Ojeda:

 - GCC build: fix bindgen build error with '-fstrict-flex-arrays'

 - Error module: fix the description for 'ECHILD' and fix Markdown
   style nit

 - Code docs: fix logo replacement

 - Docs: update docs output path

 - Kbuild: remove old docs output path in 'cleandocs' target

* tag 'rust-fixes-6.6' of https://github.com/Rust-for-Linux/linux:
  rust: docs: fix logo replacement
  kbuild: remove old Rust docs output path
  docs: rust: update Rust docs output path
  rust: fix bindgen build error with fstrict-flex-arrays
  rust: error: Markdown style nit
  rust: error: fix the description for `ECHILD`

Pull scheduler fix from Ingo Molnar:
 "Fix a recently introduced use-after-free bug"

* tag 'sched-urgent-2023-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/eevdf: Fix heap corruption more

Pull perf events fix from Ingo Molnar:
 "Fix group event semantics"

* tag 'perf-urgent-2023-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Disallow mis-matched inherited group reads

Merge tag 'probes-fixes-v6.6-rc6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull probes fixes from Masami Hiramatsu:

 - kprobe-events: Fix kprobe events to reject if the attached symbol is
   not unique name because it may not the function which the user want
   to attach to. (User can attach a probe to such symbol using the
   nearest unique symbol + offset.)

 - selftest: Add a testcase to ensure the kprobe event rejects non
   unique symbol correctly.

* tag 'probes-fixes-v6.6-rc6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  selftests/ftrace: Add new test case which checks non unique symbol
  tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols

Pull s390 fixes from Vasily Gorbik:

 - Fix IOMMU bitmap allocation in s390 PCI to avoid out of bounds access
   when IOMMU pages aren't a multiple of 64

 - Fix kasan crashes when accessing DCSS mapping in memory holes by
   adding corresponding kasan zero shadow mappings

 - Fix a memory leak in css_alloc_subchannel in case
   dma_set_coherent_mask fails

* tag 's390-6.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/pci: fix iommu bitmap allocation
  s390/kasan: handle DCSS mapping in memory holes
  s390/cio: fix a memleak in css_alloc_subchannel

Merge tag 'platform-drivers-x86-v6.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Hans de Goede:

 -  Fix spurious brightness down presses on newer Asus laptop models

 -  Fix backlight control not working on T2 Mac Pro all-in-ones

 -  Add Armin Wolf as new maintainer for the WMI bus driver and change
    its status from orphaned to maintained

 -  A few other small fixes

* tag 'platform-drivers-x86-v6.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/mellanox: mlxbf-tmfifo: Fix a warning message
  apple-gmux: Hard Code max brightness for MMIO gmux
  platform/surface: platform_profile: Propagate error if profile registration fails
  platform/x86: asus-wmi: Map 0x2a code, Ignore 0x2b and 0x2c events
  platform/x86: asus-wmi: Only map brightness codes when using asus-wmi backlight control
  platform/x86: asus-wmi: Change ASUS_WMI_BRN_DOWN code from 0x20 to 0x2e
  platform/x86: wmi: Update MAINTAINERS entry
  platform/x86: msi-ec: Fix the 3rd config
  platform/x86: intel-uncore-freq: Conditionally create attribute for read frequency
  platform: mellanox: Fix a resource leak in an error handling path in probing flow

Pull USB / Thunderbolt fixes and ids from Greg KH:
 "Here are four small patches for USB and Thunderbolt for 6.6-rc7 that
  do the following:

   - new usb-serial device ids

   - thunderbolt driver fix for reported issue

  All of these have been in linux-next with no reported problems"

* tag 'usb-6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: option: add Fibocom to DELL custom modem FM101R-GL
  USB: serial: option: add entry for Sierra EM9191 with new firmware
  USB: serial: option: add Telit LE910C4-WWX 0x1035 composition
  thunderbolt: Call tb_switch_put() once DisplayPort bandwidth request is finished

Pull crypto fix from Herbert Xu:
 "Fix a 6.5 regression in crypto/asymmetric_keys"

* tag 'v6.6-p5' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  KEYS: asymmetric: Fix sign/verify on pkcs1pad without a hash

Pull iomap fix from Darrick Wong:

 - Fix a bug where a writev consisting of a bunch of sub-fsblock writes
   where the last buffer address is invalid could lead to an infinite
   loop

* tag 'iomap-6.6-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: fix short copy in iomap_write_iter()

Merge tag 'perf-tools-fixes-for-v6.6-2-2023-10-20' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix regression in reading scale and unit files from sysfs for PMU
   events, so that we can use that info to pretty print instead of
   printing raw numbers:

     # perf stat -e power/energy-ram/,power/energy-gpu/ sleep 2

      Performance counter stats for 'system wide':

                 1.64 Joules power/energy-ram/
                 0.20 Joules power/energy-gpu/

          2.001228914 seconds time elapsed
     #
     # grep -m1 "model name" /proc/cpuinfo
     model name	: Intel(R) Core(TM) i7-8650U CPU @ 1.90GHz
     #

 - The small llvm.cpp file used to check if the llvm devel files are
   present was incorrectly deleted when removing the BPF event in 'perf
   trace', put it back as it is also used by tools/bpf/bpftool, that
   uses llvm routines to do disassembly of BPF object files.

 - Fix use of addr_location__exit() in dlfilter__object_code(), making
   sure that it is only used to pair a previous addr_location__init()
   call.

* tag 'perf-tools-fixes-for-v6.6-2-2023-10-20' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
  tools build: Fix llvm feature detection, still used by bpftool
  perf dlfilter: Add a test for object_code()
  perf dlfilter: Fix use of addr_location__exit() in dlfilter__object_code()
  perf pmu: Fix perf stat output with correct scale and unit

Merge tag 'linux_kselftest_active-fixes-6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fix from Shuah Khan:
 "One single fix to assert check in user_events abi_test to properly
  check bit value on Big Endian architectures. The code treated the bit
  values as Little Endian and the check failed on Big Endian"

* tag 'linux_kselftest_active-fixes-6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/user_events: Fix abi_test for BE archs

Pull NFS client fixes from Anna Schumaker:
 "Stable Fix:
   - Fix a pNFS hang in nfs4_evict_inode()

  Fixes:
   - Force update of suid/sgid bits after an NFS v4.2 ALLOCATE op
   - Fix a potential oops in nfs_inode_remove_request()
   - Check the validity of the layout pointer in ff_layout_mirror_prepare_stats()
   - Fix incorrectly marking the pNFS MDS with USE_PNFS_DS in some cases"

* tag 'nfs-for-6.6-4' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFSv4.1: fixup use EXCHGID4_FLAG_USE_PNFS_DS for DS server
  pNFS/flexfiles: Check the layout validity in ff_layout_mirror_prepare_stats
  pNFS: Fix a hang in nfs4_evict_inode()
  NFS: Fix potential oops in nfs_inode_remove_request()
  nfs42: client needs to strip file mode's suid/sgid bit after ALLOCATE op

Pull fanotify fix from Jan Kara:
 "Disable superblock / mount marks for filesystems that can encode file
  handles but not open them (currently only overlayfs).

  It is not clear the functionality is useful in any way so let's better
  disable it before someone comes up with some creative misuse"

* tag 'fsnotify_for_v6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fanotify: limit reporting of event with non-decodeable file handles