Merge tag 'mvebu-dt64-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt

mvebu dt64 for 6.10 (part 1)

Few dts fix for dt validation

* tag 'mvebu-dt64-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
  arm64: dts: marvell: espressobin-ultra: fix Ethernet Switch unit address
  arm64: dts: marvell: turris-mox: drop unneeded flash address/size-cells
  arm64: dts: marvell: eDPU: drop redundant address/size-cells
  arm64: dts: marvell: cn9130-crb: drop unneeded "status"
  arm64: dts: marvell: cn9130-crb: drop wrong unit-addresses
  arm64: dts: marvell: cn9130-db: drop wrong unit-addresses
  arm64: dts: marvell: cn9131-db: drop unneeded flash address/size-cells
  arm64: dts: marvell: cn9130-db: drop unneeded flash address/size-cells
  arm64: dts: marvell: ap80x: fix IOMMU unit address

Link: https://lore.kernel.org/r/87jzk8ndyy.fsf@BLaptop.bootlin.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The Espressobin Ultra DTS includes Espressobin DTSI which defines
ethernet-switch@1 node.  The Ultra DTS overrides "reg" to 3, but that
leaves still old unit address which conflicts with the new phy@1 node
(W=1 dtc warning):

  armada-3720-espressobin.dtsi:148.29-203.4: Warning (unique_unit_address_if_enabled): /soc/internal-regs@d0000000/mdio@32004/ethernet-switch@1: duplicate unit-address (also used in node /soc/internal-regs@d0000000/mdio@32004/ethernet-phy@1)

Fix this by deleting ethernet-switch@1 node and merging original node
with code from Ultra DTS into new ethernet-switch@3.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

Flash node uses single "partition" node to describe partitions, so
remove deprecated address/size-cells properties to also fix dtc W=1
warnings:

  armada-3720-turris-mox.dts:218.10-255.4: Warning (avoid_unnecessary_addr_size): /soc/internal-regs@d0000000/spi@10600/flash@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

The ethernet-switch node does not have children with unit addresses, so
address/size-cells are not really correct, as reported by dtc W=1
warning:

  armada-3720-eDPU.dts:26.19-60.4: Warning (avoid_unnecessary_addr_size): /soc/internal-regs@d0000000/mdio@32004/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

This probably also fixes dtbs_check warning, but I could not find it, so
not sure about that.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

Merge tag 'ti-k3-dt-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt

TI K3 device tree updates for v6.10

Generic Cleanups/Fixes:
- fixup of generated dtb imx219 overlay file names
- Remove UART baud rate selection in device tree.
- Use exact ranges for FSS.

SoC specific Fixes/Features:

AM625:
- Add USB PHY2 region and usb phy control registers

AM62A
- Add USB PHY2 region and usb phy control registers, Disable USB LPM.
- Add wave-512 video encoder/decoder support
- Enable UHS mode for SD

AM62P:
- Disable ethernet by default
- Add USB support

AM654
- Serdes fixups
- SDHCI fixups.

AM67/j722s:
- Disable ethernet by default
- Add USB support

AM68/J721s2:
- Add main ESM range
- Add support for SDR104

AM69/J784S4:
- Add main ESM range
- Enable support for UHS mode

Board specific fixes/Features:

AM625:
- BeaglePlay: Fixes for wlan mmc-pwrseq and ethernet phy reset
- phyboard-lyra: Add Audio codec, USB-C, increase CAN bit rate and enable
  ability to apply overlays
- verdin: GPIO pinctrl fixups, Switch SD carddetect to GPIO, fixup memory
  to 2GB, and audio clock, PCIe reset GPIO hog, sleep-moci
- lp-sk: Drop power button
- sk: minor white space cleanup.

AM64
- phyboard-electra: Increase CAN bit rate, enable overlay to enable GPIO fan

AM65:
- iot2050: Add icssg-prueth for PG1

AM67/j722s:
- evm: Enable UHS support for SD card and eMMC support.

AM69/J784s4:
- evm/sk: Fix uart pins and pinctrl macro usage.

* tag 'ti-k3-dt-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (48 commits)
  arm64: dts: ti: Fix csi2-dual-imx219 dtb names
  arm64: dts: ti: k3-am625-beagleplay: Fix Ethernet PHY RESET GPIOs
  arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Add USB-C
  arm64: dts: ti: k3-j784s4: Add main esm address range
  arm64: dts: ti: k3-j721s2: Add main esm address range
  arm64: dts: ti: k3-am62-verdin-dahlia: support sleep-moci
  arm64: dts: ti: k3-am62-verdin: replace sleep-moci hog with regulator
  arm64: dts: ti: k3-j722s-evm: Enable UHS support for MMCSD
  arm64: dts: ti: k3-j784s4-main: Enable support for UHS mode
  arm64: dts: ti: k3-j721s2-main: Enable support for SDR104 speed mode
  arm64: dts: ti: k3-am62a: Enable UHS mode support for SD cards
  arm64: dts: ti: k3-am65-main: Remove unused properties in sdhci nodes
  arm64: dts: ti: k3-am65-main: Fix sdhci node properties
  arm64: dts: ti: Enable overlays for the am625-phyboard-lyra
  arm64: dts: ti: am64-phyboard-electra: Add overlay to enable a GPIO fan
  arm64: dts: ti: k3-am62a-main: Add Wave5 Video Encoder/Decoder Node
  arm64: dts: ti: k3-am69-sk: Fix UART pin type and macro type
  arm64: dts: ti: k3-j784s4-evm: Fix UART pin type and macro type
  arm64: dts: ti: k3-am62a: Disable USB LPM
  arm64: dts: ti: k3-am62p: add the USB sub-system
  ...

Link: https://lore.kernel.org/r/20240501124319.ake5j2oc5pbnn5nb@contourSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'ti-keystone-dt-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt

Keystone2 device tree updates for v6.10

Generic Cleanups/Fixes:
-  Remove custom ti,system-reboot-controller property

* tag 'ti-keystone-dt-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
  dt-bindings: arm: keystone: Remove ti,system-reboot-controller property
  ARM: dts: ti: keystone: k2g: Remove ti,system-reboot-controller property

Link: https://lore.kernel.org/r/20240501124309.3cj5b3gjf3cpimut@outsellSigned-off-by: Arnd Bergmann <arnd@arndb.de>

RISC-V Devicetrees for v6.10

Sophgo:
Added sdhci support for cv18xx/duo.
Added clock support for cv18xx.
Added clock for uart/sdhci.
Added spi support for cv18xx.
Added i2c support for cv18xx.
Added reserved memory node for cv1800b/duo.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>

* tag 'riscv-sophgo-dt-for-v6.10' of https://github.com/sophgo/linux:
  riscv: dts: sophgo: add reserved memory node for CV1800B
  riscv: dts: sophgo: use real clock for sdhci
  riscv: dts: sophgo: cv18xx: Add i2c devices
  riscv: dts: sophgo: cv18xx: Add spi devices
  riscv: dts: sophgo: add uart clock for Sophgo CV1800 series SoC
  riscv: dts: sophgo: add clock generator for Sophgo CV1800 series SoC
  riscv: dts: sophgo: add sdcard support for milkv duo

Link: https://lore.kernel.org/r/MA0P287MB2822CA2DE757787D6EA3B1F8FE192@MA0P287MB2822.INDP287.PROD.OUTLOOK.COMSigned-off-by: Arnd Bergmann <arnd@arndb.de>

'/memory' nodes always have a 'reg' property, and therefore should have
a unit-address with just plain hex (i.e. no commas). Fix all the arm64
'/memory' nodes.

It's possible that some bootloader depends on /memory (arm32 ATAG to DT
code does for example). If so, the memory node should be commented with
that requirement.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Chanho Min <chanho.min@lge.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240430191856.874600-2-robh@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Fix the output filenames of the combined device tree blobs generated by
applying *-csi2-dual-imx219-* overlays on the base dtbs during compile
test.

Fixes: f767eb91 ("arm64: dts: ti: k3-j721e-sk: Add overlay for IMX219")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/104fbdbc-a3f6-091a-72f4-17d4fa24ad92@ti.com/Signed-off-by: Nishanth Menon <nm@ti.com>

This pull request contains Broadcom ARM64-based SoCs Device Tree updates
for 6.10, please pull the following:

- Rafal moves the "brcm,wp-not-connected" property from the individual
  board DTSes to the SoC' DTSI since all boards a designed the same way

* tag 'arm-soc/for-6.10/devicetree-arm64' of https://github.com/Broadcom/stblinux:
  arm64: dts: broadcom: bcmbca: bcm4908: set brcm,wp-not-connected

Link: https://lore.kernel.org/r/20240429213703.2327834-3-florian.fainelli@broadcom.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 6.10, please pull the following:

- Laurent converts the Raspberry Pi firmware DT binding to YAML, updates
  the firmware driver to use the proper 'struct device' reference for
  DMA mappings and drops unneeded properties from the DT node and
  finishes by removing the duplicate firmware-clocks property to
  bcm2835-rpi.dtsi. He also added support for the CAM1 camera interface
  regulator.

- Uwe adds a pinctrl-based multiplexing description to allow the use of
  I2C0 pins to allow usage between the 40-pin Raspberry Pi header and
  the CSI and DSI connectors. He then describes the PCF85063 RTC device
  available on the CM4 I/O board making use of that pinctrl-based
  muxing.

- Arinc updates the Asus RT-AC3100 and RT-AC88U DTs to have proper LED
  colors and function properties, NVMEM MAC addresses and removes
  duplicates and unnecessary properties and does a few Device Tree
  cleanups.. He then adds support for the Asus RT-AC3200 (BCM4709-based)
  and RT-AC3500 routers.

- Jean-Michel adds DT nodes for the CSI Unicam camera interfaces on the
  Raspberry Pi 4 / BCM2711 SoCs

- Florian adds support for the Ethernet LEDs on Raspberry Pi 4 B and
  Raspberry Pi 4 CM boards.

* tag 'arm-soc/for-6.10/devicetree' of https://github.com/Broadcom/stblinux:
  arm: dts: bcm2711: Describe Ethernet LEDs
  ARM: dts: BCM5301X: Conform to DTS Coding Style on ASUS RT-AC3100 & AC88U
  ARM: dts: BCM5301X: Add DT for ASUS RT-AC5300
  ARM: dts: BCM5301X: Add DT for ASUS RT-AC3200
  dt-bindings: arm: bcm: add bindings for ASUS RT-AC5300
  dt-bindings: arm: bcm: add bindings for ASUS RT-AC3200
  ARM: dts: bcm2835: Add Unicam CSI nodes
  ARM: dts: BCM5301X: remove earlycon on ASUS RT-AC3100 and ASUS RT-AC88U
  ARM: dts: BCM5301X: remove duplicate compatible on ASUS RT-AC3100 & AC88U
  ARM: dts: BCM5301X: provide address for SoC MACs on ASUS RT-AC3100 & AC88U
  ARM: dts: BCM5301X: use color and function on ASUS RT-AC3100 and RT-AC88U
  ARM: dts: bcm2711-rpi-4-b: Add CAM1 regulator
  ARM: dts: bcm2711-rpi-cm4-io: Add RTC on I2C0
  ARM: dts: bcm2711-rpi: Add pinctrl-based multiplexing for I2C0
  ARM: dts: bcm2835-rpi: Move duplicate firmware-clocks to bcm2835-rpi.dtsi
  ARM: dts: bcm283x: Drop unneeded properties in the bcm2835-firmware node
  firmware: raspberrypi: Use correct device for DMA mappings
  dt-bindings: arm: bcm: raspberrypi,bcm2835-firmware: Add gpio child node

Link: https://lore.kernel.org/r/20240429213703.2327834-2-florian.fainelli@broadcom.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The RESET GPIO pinmux should be part of MDIO bus node
so that they can be in the right state before the PHY
can be probed via MDIO bus scan.

The GPIO pin should be setup with PIN_INPUT so that
input circuitry is enabled in case software wants to
check pin status. Without this, incorrect status is shown
in /sys/kernel/debug/gpio.

Add GPIO reset for the Gigabit Ethernet PHY. As per
RTL8211F datasheet, reset assert width is 10ms and
PHY registers can be access accessed after 50ms of
reset deassert.

Fixes: f5a731f0 ("arm64: dts: ti: Add k3-am625-beagleplay")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240305-b4-for-v6-9-am65-beagleplay-ethernet-reset-v2-1-2bf463a7bf13@kernel.orgSigned-off-by: Nishanth Menon <nm@ti.com>

The USB-C PD manages plug orientation, power delivery, and our endpoint
for the USB interface. Add this node and include its endpoint.

Configure USB0 for role-switching and wire it to our USB-C PD endpoint.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240425152558.485763-1-ggiordano@phytec.comSigned-off-by: Nishanth Menon <nm@ti.com>

Main ESM address change was missing for J784S4 SOC,
So adding main ESM address mapping.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240424075423.1229127-3-u-kumar1@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Main ESM address change was missing for J721S2 SOC,
So adding main ESM address mapping.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240424075423.1229127-2-u-kumar1@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Previously, we had the sleep-moci pin set to always on. However, the
Dahlia carrier board supports disabling the sleep-moci when the system
is suspended to power down peripherals that support it. This reduces
overall power consumption. This commit adds support for this feature by
disabling the reg_force_sleep_moci regulator and adding a new regulator
for the USB hub that can be turned off when the system is suspended.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240301084901.16656-3-eichest@gmail.comSigned-off-by: Nishanth Menon <nm@ti.com>

The Verdin family has a signal called sleep-moci which can be used to
turn off peripherals on the carrier board when the SoM goes into
suspend. So far we have hogged this signal, which means the peripherals
are always on and it is not possible to add peripherals that depend on
the sleep-moci to be on. With this change, we replace the hog with a
regulator so that peripherals can add their own regulators that use the
same gpio. Carrier boards that allow peripherals to be powered off in
suspend can disable this regulator and implement their own regulator to
control the sleep-moci.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240301084901.16656-2-eichest@gmail.comSigned-off-by: Nishanth Menon <nm@ti.com>

Enable the UHS modes for MMCSD in J722S by removing the
no-1-8-v property.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240422131840.34642-1-b-kapoor@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Remove sdhci-caps-mask to enable support for SDR104 speed mode for
SD card and remove no-1-8-v property so that SD card can work in
any UHS-1 high speed mode it can support.

Fixes: 4664ebd8 ("arm64: dts: ti: Add initial support for J784S4 SoC")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-6-jm@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

According to TRM for J721S2, SDR104 speed mode is supported by the SoC
but its capabilities were masked in device tree. Remove sdhci-caps-mask
to enable support for SDR104 speed mode for SD card in J721S2 SoC.

[+] Refer to : section 12.3.6.1.1 MMCSD Features, in J721S2 TRM
- https://www.ti.com/lit/zip/spruj28

Fixes: b8545f9d ("arm64: dts: ti: Add initial support for J721S2 SoC")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-5-jm@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Hook up required IO voltage regulators and drop no-1-8-v to support UHS
modes on SD cards.

Fixes: 5fc6b1b6 ("arm64: dts: ti: Introduce AM62A7 family of SoCs")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-4-jm@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

On AM65x platform, sdhci0 is for eMMC and sdhci1 is for SD.
Remove the properties that are not applicable for each device.

Fixes: eac99d38 ("arm64: dts: ti: k3-am654-main: Update otap-del-sel values")
Fixes: d7600d07 ("arm64: dts: ti: k3-am65-main: Add support for sdhci1")
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-3-jm@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Update otap-del-sel properties as per datasheet [0].

Add missing clkbuf-sel and itap-del-sel values also as per
datasheet [0].

Move clkbuf-sel and ti,trm-icp above the otap-del-sel properties
so the sdhci nodes could be more uniform across platforms.

[0] https://www.ti.com/lit/ds/symlink/am6548.pdf

Fixes: eac99d38 ("arm64: dts: ti: k3-am654-main: Update otap-del-sel values")
Fixes: d7600d07 ("arm64: dts: ti: k3-am65-main: Add support for sdhci1")
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-2-jm@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Add symbols when building the am625-phyboard-lyra-rdk DTB so
overlays can be applied.

Fixes: d8280f30 ("arm64: dts: ti: am62-phyboard-lyra: Add overlay to enable a GPIO fan")
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240419193552.3090343-1-nmorrisson@phytec.comSigned-off-by: Nishanth Menon <nm@ti.com>

The phyBOARD-Electra has a GPIO fan header. This overlay enables the fan
header and sets the fan to turn on at 65C.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240419193114.3090084-1-nmorrisson@phytec.comSigned-off-by: Nishanth Menon <nm@ti.com>

This patch adds support for the Wave521cl on the AM62A-SK.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20240415204659.798548-1-b-brnich@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Along fixing wkup UART RTS and TX pins as OUTPUT instead of INPUT
updating J784S4 macro for pin mux instead of J721S2.

Fixes: 45299dd1 ("arm64: dts: ti: k3-am69-sk: Add mcu and wakeup uarts")
Fixes: 08ae12b6 ("arm64: dts: ti: k3-am69-sk: Enable wakeup_i2c0 and eeprom")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240415095605.3547933-3-u-kumar1@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Along fixing wkup UART TX pin as OUTPUT instead of INPUT,
updating J784S4 macro for pin mux instead of J721S2.

Fixes: 5dfbd1de ("arm64: dts: ti: k3-j784s4-evm: Enable wakeup_i2c0 and eeprom")
Fixes: 6fa5d37a ("arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240415095605.3547933-2-u-kumar1@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

As per AM62A TRM [1] USB Link Power Management (LPM)
feature is not supported. Disable it else it may
cause enumeration failure on some devices.

> 4.9.2.1 USB2SS Unsupported Features
> The following features are not supported on this family of devices:
> ...
> - USB 2.0 ECN: Link Power Management (LPM)
> ...

[1] - https://www.ti.com/lit/pdf/spruj16Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20240412-for-v6-10-am62-usb-typec-dt-v7-3-93b827adf97e@kernel.orgSigned-off-by: Nishanth Menon <nm@ti.com>

There are two USB instances available on the am62p5 starter kit. Include
and enable them for use on the board.

USB LPM feature is kept disabled as it is not supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240412-for-v6-10-am62-usb-typec-dt-v7-2-93b827adf97e@kernel.orgSigned-off-by: Nishanth Menon <nm@ti.com>

Exposing the entire CTRL_MMR space to syscon is not a good idea.
Add sub-nodes for USB0_PHY_CTRL and USB1_PHY_CTRL and use them
in the USB0/USB1 nodes.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240412-for-v6-10-am62-usb-typec-dt-v7-1-93b827adf97e@kernel.orgSigned-off-by: Nishanth Menon <nm@ti.com>

Add PHY2 register space to USB wrapper node. This is required
to deal with Errata i2409.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240412-for-v6-9-am62-usb-errata-dt-v1-1-ef0d79920f75@kernel.org
Closes: https://lore.kernel.org/all/20240408095200.GA14655@francesco-nb/Signed-off-by: Nishanth Menon <nm@ti.com>

Add the required nodes to enable ICSSG SR1.0 based prueth networking.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Link: https://lore.kernel.org/r/20240409164314.157602-1-diogo.ivo@siemens.comSigned-off-by: Nishanth Menon <nm@ti.com>

The Audio Codec runs over the MCASP (Multichannel Audio Serial Port).

Add pinmux for the Audio Reference Clock and MCASP2.

Add DT nodes for Audio Codec, MCASP2, VCC 1v8 and VCC 3v3 regulators.

Additionally, create a sound node that connects our sound card and the
MCASP2.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240404184250.3772829-1-ggiordano@phytec.comSigned-off-by: Nishanth Menon <nm@ti.com>

Merge tag 'microchip-dt64-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt

Microchip ARM64 device tree updates for v6.10

It contains:
- dtbs_check and dtc W=1 warning fixes
- mdio2 and serdes address fixes for sparx5

* tag 'microchip-dt64-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  arm64: dts: microchip: sparx5_pcb135: drop duplicated NOR flash
  arm64: dts: microchip: sparx5_pcb134: drop duplicated NOR flash
  arm64: dts: microchip: sparx5_pcb135: drop LED unit addresses
  arm64: dts: microchip: sparx5_pcb134: drop LED unit addresses
  arm64: dts: microchip: sparx5_pcb135: align I2C mux node name with bindings
  arm64: dts: microchip: sparx5_pcb134: align I2C mux node name with bindings
  arm64: dts: microchip: sparx5_pcb135: add missing I2C mux unit addresses
  arm64: dts: microchip: sparx5_pcb134: add missing I2C mux unit addresses
  arm64: dts: microchip: sparx5: correct serdes unit address
  arm64: dts: microchip: sparx5: fix mdio reg

Link: https://lore.kernel.org/r/20240429121429.1941241-1-claudiu.beznea@tuxon.devSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'dt-cleanup-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt

Minor improvements in ARM DTS for v6.10

1. TI: add missing white-spaces for code readability.
2. Aspeed: add vendor prefix to compatibles, to properly describe
   hardware, even though Linux drivers match by device name.

* tag 'dt-cleanup-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
  ARM: dts: aspeed: Add vendor prefixes to lm25066 compat strings
  ARM: dts: ti: omap: minor whitespace cleanup

Link: https://lore.kernel.org/r/20240428163316.28955-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'dt64-cleanup-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt

Minor improvements in ARM64 DTS for v6.10

Fixes, which might have practical impact, however things were broken for
long enough to justify pushing it regular path:
1. ARM Juno: shorten node names for thermal zones, because Linux drivers
   have strict limit of 20 characters.
2. HiSilicon: correct size of GIC GICC address space and add missing
   GICH and GICV spaces, add cache info to properly describe cache
   topology and solve kernel boot warning.

Several cleanups:
1. Use capital "OR" for multiple licenses in SPDX.
2. Correct white-spaces for code readability.
3. Fix W=1 dtc compiler warnings, which should not have practical
   impact for Amazon, APM, Cavium, Realtek, Socionext Uniphier and
   Spreadtrum like:
    - missing unit addresses,
    - nodes not belonging to soc node,
    - not using generic node names,
    - few incorrect unit addresses.

* tag 'dt64-cleanup-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt: (28 commits)
  arm64: dts: cavium: thunder2-99xx: drop redundant reg-names
  arm64: dts: amazon: alpine-v3: correct gic unit addresses
  arm64: dts: amazon: alpine-v3: drop cache nodes unit addresses
  arm64: dts: amazon: alpine-v3: add missing io-fabric unit addresses
  arm64: dts: amazon: alpine-v2: move non-MMIO node out of soc
  arm64: dts: amazon: alpine-v2: add missing io-fabric unit addresses
  arm64: dts: apm: shadowcat: move non-MMIO node out of soc
  arm64: dts: apm: storm: move non-MMIO node out of soc
  arm64: dts: cavium: correct unit addresses
  arm64: dts: cavium: move non-MMIO node out of soc
  arm64: dts: realtek: rtc16xx: add missing unit address to soc node
  arm64: dts: realtek: rtd139x: add missing unit address to soc node
  arm64: dts: realtek: rtd129x: add missing unit address to soc node
  arm64: dts: uniphier: ld20-global: drop audio codec port unit address
  arm64: dts: uniphier: ld20-global: use generic node name for audio-codec
  arm64: dts: uniphier: ld11-global: drop audio codec port unit address
  arm64: dts: uniphier: ld11-global: use generic node name for audio-codec
  arm64: dts: sharkl3: add missing unit addresses
  arm64: dts: whale2: add missing ap-apb unit address
  arm64: dts: sc9860: move GIC to soc node
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-dt64-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt

i.MX arm64 device tree for 6.10:

- New board support: Emcraft Systems NavQ+ Kit, Toradex Colibri iMX8DX,
  and S32G-VNP-RDB3 board.
- A series from Alexander Stein that adds empty DSI output endpoint to
  simplify DSI connection description at board level.
- Add pinmux and I2C GPIOs to support bus recovery for LX2160A.
- Add cm40 subsystem description for i.MX8 SoCs.
- A series from Frank Li that adds ADC, LPSPI and FlexSPI devices for
  imx8qm-mek board.
- Add audio devices ASRC, ESAI, SPDIF and SAI for i.MX8QXP and correct
  audio LPCG index.
- A couple of changes from Ghennadi Procopciuc that add SCMI firmware
  and uSDHC nodes for S32G SoC.
- A couple of imx8mp-msc-sm2s updates from Ian Ray improving I2C pad
  drive strength and adding SDA/SCL GPIOs for I2C devices.
- Add PCA9451A PMIC and PCF2131 RTC support for imx93-11x11-evk board.
- A series from Lucas Stach to enable HDMI display support for i.MX8MP.
- A series from Peng Fan to improve i.MX93 support for LPI2C, LPSPI, FEC
  and eQoS.
- A couple of LS1028A changes from Rob Herring to improve PCI device
  description.
- A series from Shengjiu Wang adding HDMI and PDM mic sound support for
  imx8mp-evk board.
- A number of i.MX8M Venice device improvements from Stefan Eichenberger,
  Tim Harvey and Vitor Soares.
- A series from Xu Yang that enables USB support for imx8ulp-evk and
  imx93-11x11-evk board.
- Other small and random updates on various boards.

* tag 'imx-dt64-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (78 commits)
  arm64: dts: imx93-11x11-evk: add RTC PCF2131 support
  arm64: dts: imx93-11x11-evk: add reset gpios for ethernet PHYs
  arm64: dts: imx93-11x11-evk: add sleep pinctrl for sdhc2
  arm64: dts: imx93-11x11-evk: add different usdhc pinctrl for different timing usage
  arm64: dts: imx93-11x11-evk: add sleep pinctrl for eqos and fec
  arm64: dts: imx93-11x11-evk: update resource table address
  arm64: dts: imx93: add nvmem property for eqos
  arm64: dts: imx93: add nvmem property for fec1
  arm64: dts: imx93: assign usdhc[1..3] root clock to 400MHz
  arm64: dts: imx93: add dma support for lpspi[1..8]
  arm64: dts: imx93: add dma support for lpi2c[1..8]
  arm64: dts: imx93: use FSL_EDMA_RX for rx channel
  arm64: dts: freescale: ls1028a: Add standard PCI device compatible strings to ENETC
  arm64: dts: freescale: ls1028a: Fix embedded PCI interrupt mapping
  arm64: dts: imx8qxp-mek: add cm40_i2c, wm8960 and sai[0,1,4,5]
  arm64: dts: imx8mp: Align both CSI2 pixel clock
  arm64: dts: freescale: imx8m[mp]-verdin: Update audio card name
  arm64: dts: imx8mp: Enable HDMI on TQMa8MPxL/MBa8MPxL
  arm64: dts: imx8ulp: add caam jr
  arm64: dts: imx8mp-msc-sm2s: Add i2c{1,6} sda-/scl-gpios
  ...

Link: https://lore.kernel.org/r/20240428121247.10370-4-shawnguo2@yeah.netSigned-off-by: Arnd Bergmann <arnd@arndb.de>

i.MX ARM device tree for 6.10:

- New board support: Seeed Studio NPi dev board, UNI-T UTi260B thermal
  camera board.
- A couple of IRQ config correction for touchscreen and RC5T619 on
  tolino-shine2hd device.
- Add snvs-poweroff support for i.MX7.
- A couple of dtb_check warning fixes on i.MX6SX and i.MX6QDL ESAI.
- Enable USB support for imx6qdl-udoo and imx27-phytec.
- A big series from Uwe Kleine-König to adopt #pwm-cells = <3> for i.MX
  devices.
- Other small changes and clean-ups.

* tag 'imx-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (64 commits)
  ARM: dts: imx6ul-pico: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-kontron-bl-common: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-kontron-bl-43: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-isiot: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-imx6ull-opos6uldev: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-geam: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-ccimx6ulsbcpro: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6ul-14x14-evk: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sx-softing-vining-2000: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sx-sdb: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sx-nitrogen6sx: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sll-evk: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6sl-evk: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-var-dt6customboard: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-prti6q: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-pistachio: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-novena: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6q-kp: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-skov-cpu: Use #pwm-cells = <3> for imx27-pwm device
  ARM: dts: imx6qdl-savageboard: Use #pwm-cells = <3> for imx27-pwm device
  ...

Link: https://lore.kernel.org/r/20240428121247.10370-3-shawnguo2@yeah.netSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-bindings-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt

i.MX DT bindings for 6.10:

- Add vendor prefix for Emcraft Systems
- Add compatible for new boards: Emcraft Systems i.MX8M Plus NavQ+ Kit,
  Colibri iMX8DX, Seeed studio NPi base board, NXP S32G3 board
- Drop reduntant toradex,colibri-imx8x from fsl.yaml
- Add usbmisc compatible for i.MX8ULP

* tag 'imx-bindings-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  dt-bindings: usb: usbmisc-imx: add fsl,imx8ulp-usbmisc compatible
  dt-bindings: arm: fsl: Add Colibri iMX8DX
  dt-bindings: arm: fsl: remove reduntant toradex,colibri-imx8x
  dt-bindings: arm: Add Emcraft Systems i.MX8M Plus NavQ+ Kit
  dt-bindings: vendor-prefixes: Add Emcraft Systems
  dt-bindings: arm: fsl: add NXP S32G3 board
  dt-bindings: arm: fsl: Add Seeed studio NPi based boards

Link: https://lore.kernel.org/r/20240428121247.10370-2-shawnguo2@yeah.netSigned-off-by: Arnd Bergmann <arnd@arndb.de>