Extend netlink interface to add and delete XFRM policy from the device.
This functionality is a first step to implement packet IPsec offload solution.
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Allow users to configure xfrm states with packet offload mode.
The packet mode must be requested both for policy and state, and
such requires us to do not implement fallback.

We explicitly return an error if requested packet mode can't
be configured.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

In the next patches, the xfrm core code will be extended to support
new type of offload - packet offload. In that mode, both policy and state
should be specially configured in order to perform whole offloaded data
path.

Full offload takes care of encryption, decryption, encapsulation and
other operations with headers.

As this mode is new for XFRM policy flow, we can "start fresh" with flag
bits and release first and second bit for future use.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

In order to fix the following sleep while atomic bug always alloc pages
with GFP_ATOMIC in mtk_wed_wo_queue_refill since page_frag_alloc runs in
spin_lock critical section.

[    9.049719] Hardware name: MediaTek MT7986a RFB (DT)
[    9.054665] Call trace:
[    9.057096]  dump_backtrace+0x0/0x154
[    9.060751]  show_stack+0x14/0x1c
[    9.064052]  dump_stack_lvl+0x64/0x7c
[    9.067702]  dump_stack+0x14/0x2c
[    9.071001]  ___might_sleep+0xec/0x120
[    9.074736]  __might_sleep+0x4c/0x9c
[    9.078296]  __alloc_pages+0x184/0x2e4
[    9.082030]  page_frag_alloc_align+0x98/0x1ac
[    9.086369]  mtk_wed_wo_queue_refill+0x134/0x234
[    9.090974]  mtk_wed_wo_init+0x174/0x2c0
[    9.094881]  mtk_wed_attach+0x7c8/0x7e0
[    9.098701]  mt7915_mmio_wed_init+0x1f0/0x3a0 [mt7915e]
[    9.103940]  mt7915_pci_probe+0xec/0x3bc [mt7915e]
[    9.108727]  pci_device_probe+0xac/0x13c
[    9.112638]  really_probe.part.0+0x98/0x2f4
[    9.116807]  __driver_probe_device+0x94/0x13c
[    9.121147]  driver_probe_device+0x40/0x114
[    9.125314]  __driver_attach+0x7c/0x180
[    9.129133]  bus_for_each_dev+0x5c/0x90
[    9.132953]  driver_attach+0x20/0x2c
[    9.136513]  bus_add_driver+0x104/0x1fc
[    9.140333]  driver_register+0x74/0x120
[    9.144153]  __pci_register_driver+0x40/0x50
[    9.148407]  mt7915_init+0x5c/0x1000 [mt7915e]
[    9.152848]  do_one_initcall+0x40/0x25c
[    9.156669]  do_init_module+0x44/0x230
[    9.160403]  load_module+0x1f30/0x2750
[    9.164135]  __do_sys_init_module+0x150/0x200
[    9.168475]  __arm64_sys_init_module+0x18/0x20
[    9.172901]  invoke_syscall.constprop.0+0x4c/0xe0
[    9.177589]  do_el0_svc+0x48/0xe0
[    9.180889]  el0_svc+0x14/0x50
[    9.183929]  el0t_64_sync_handler+0x9c/0x120
[    9.188183]  el0t_64_sync+0x158/0x15c

Fixes: 79968444 ("net: ethernet: mtk_wed: introduce wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/67ca94bdd3d9eaeb86e52b3050fbca0bcf7bb02f.1669908312.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

kfree_rcu(1-arg) should be avoided as much as possible,
since this is only possible from sleepable contexts,
and incurr extra rcu barriers.

I wish the 1-arg variant of kfree_rcu() would
get a distinct name, like kfree_rcu_slow()
to avoid it being abused.

Fixes: 459837b5 ("net/tcp: Disable TCP-MD5 static key on tcp_md5sig_info destruction")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20221202052847.2623997-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v6.2

Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.

Major changes:

ath10k
 - store WLAN firmware version in SMEM image table

mt76
 - mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
 - mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
 - mt7915: add ack signal support
 - mt7915: enable coredump support
 - mt7921: remain_on_channel support
 - mt7921: channel context support

iwlwifi
 - enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
 - 320 MHz channels support

* tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (144 commits)
  wifi: ath10k: fix QCOM_SMEM dependency
  wifi: mt76: mt7921e: add pci .shutdown() support
  wifi: mt76: mt7915: mmio: fix naming convention
  wifi: mt76: mt7996: add support to configure spatial reuse parameter set
  wifi: mt76: mt7996: enable ack signal support
  wifi: mt76: mt7996: enable use_cts_prot support
  wifi: mt76: mt7915: rely on band_idx of mt76_phy
  wifi: mt76: mt7915: enable per bandwidth power limit support
  wifi: mt76: mt7915: introduce mt7915_get_power_bound()
  mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2()
  wifi: mt76: do not send firmware FW_FEATURE_NON_DL region
  wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc
  wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
  wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices
  wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
  wifi: mt76: mt7915: fix band_idx usage
  wifi: mt76: mt7915: enable .sta_set_txpwr support
  wifi: mt76: mt7915: add basedband Txpower info into debugfs
  wifi: mt76: mt7915: add support to configure spatial reuse parameter set
  wifi: mt76: mt7915: add missing MODULE_PARM_DESC
  ...
====================

Link: https://lore.kernel.org/r/20221202214254.D0D3DC433C1@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Nathan noticed that when HWSPINLOCK is disabled there's a Kconfig warning:

  WARNING: unmet direct dependencies detected for QCOM_SMEM
    Depends on [n]: (ARCH_QCOM [=y] || COMPILE_TEST [=n]) && HWSPINLOCK [=n]
    Selected by [m]:
    - ATH10K_SNOC [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && ATH10K [=m] && (ARCH_QCOM [=y] || COMPILE_TEST [=n])

The problem here is that QCOM_SMEM depends on HWSPINLOCK so we cannot select
QCOM_SMEM and instead we neeed to use 'depends on'.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/all/Y4YsyaIW+CPdHWv3@dev-arch.thelio-3990X/
Fixes: 4d79f6f3 ("wifi: ath10k: Store WLAN firmware version in SMEM image table")
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202103027.25974-1-kvalo@kernel.org

Refill RX queue in batches of descriptors to improve performance. Refill
is allowed to fail as long as a minimum number of descriptors is active.
Thus, a limited number of failed RX buffer allocations is now allowed
for normal operation. Previously every failed allocation resulted in a
dropped frame.

If the minimum number of active descriptors is reached, then RX buffers
are still reused and frames are dropped. This ensures that the RX queue
never runs empty and always continues to operate.

Prework for future XDP support.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without interrupt throttling, iperf server mode generates a CPU load of
100% (A53 1.2GHz). Also the throughput suffers with less than 900Mbit/s
on a 1Gbit/s link. The reason is a high interrupt load with interrupts
every ~20us.

Reduce interrupt load by throttling of interrupts. Interrupt delay
default is 64us. For iperf server mode the CPU load is significantly
reduced to ~20% and the throughput reaches the maximum of 941MBit/s.
Interrupts are generated every ~140us.

RX and TX coalesce can be configured with ethtool. RX coalesce has
priority over TX coalesce if the same interrupt is used.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow user space to read number of TX and RX queue. This is useful for
device dependent qdisc configurations like TAPRIO with hardware offload.
Also ethtool::get_per_queue_coalesce / set_per_queue_coalesce requires
that interface.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct xmit hash steps for layer3+4 as introduced by commit
49aefd13 ("bonding: do not discard lowest hash bit for non layer3+4
hashing").
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit c1f897ce ("bonding: set default miimon value for non-arp
modes if not set") the miimon default was changed from zero to 100 if
arp_interval is also zero. Document this fact in bonding.rst.

Fixes: c1f897ce ("bonding: set default miimon value for non-arp modes if not set")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The main usage of the struct thunderbolt_ip_frame_header is to handle
the packets on the media layer. The header is bound to the protocol
in which the byte ordering is crucial. However the data type definition
doesn't use that and sparse is unhappy, for example (17 altogether):

  .../thunderbolt.c:718:23: warning: cast to restricted __le32

  .../thunderbolt.c:966:42: warning: incorrect type in assignment (different base types)
  .../thunderbolt.c:966:42:    expected unsigned int [usertype] frame_count
  .../thunderbolt.c:966:42:    got restricted __le32 [usertype]

Switch to the bitwise types in the struct thunderbolt_ip_frame_header to
reduce this, but not completely solving (9 left), because the same data
type is used for Rx header handled locally (in CPU byte order).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less heavier for builds
than the use of __maybe_unused attributes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some devlink instances may contain thousands of ports. Storing them in
linked list and looking them up is not scalable. Convert the linked list
into xarray.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sebastian Andrzej Siewior says:

====================
I started playing with HSR and run into a problem. Tested latest
upstream -rc and noticed more problems. Now it appears to work.
For testing I have a small three node setup with iperf and ping. While
iperf doesn't complain ping reports missing packets and duplicates.
====================

Link: https://lore.kernel.org/r/20221129164815.128922-1-bigeasy@linutronix.de/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This test adds a basic HSRv0 network with 3 nodes. In its current shape
it sends and forwards packets, announcements and so merges nodes based
on MAC A/B information.
It is able to detect duplicate packets and packetloss should any occur.

Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

self_node_db is a list_head with one entry of struct hsr_node. The
purpose is to hold the two MAC addresses of the node itself.
It is convenient to recycle the structure. However having a list_head
and fetching always the first entry is not really optimal.

Created a new data strucure contaning the two MAC addresses named
hsr_self_node. Access that structure like an RCU protected pointer so
it can be replaced on the fly without blocking the reader.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

hsr_register_frame_out() compares new sequence_nr vs the old one
recorded in hsr_node::seq_out and if the new sequence_nr is higher then
it will be written to hsr_node::seq_out as the new value.

This operation isn't locked so it is possible that two frames with the
same sequence number arrive (via the two slave devices) and are fed to
hsr_register_frame_out() at the same time. Both will pass the check and
update the sequence counter later to the same value. As a result the
content of the same packet is fed into the stack twice.

This was noticed by running ping and observing DUP being reported from
time to time.

Instead of using the hsr_priv::seqnr_lock for the whole receive path (as
it is for sending in the master node) add an additional lock that is only
used for sequence number checks and updates.

Add a per-node lock that is used during sequence number reads and
updates.

Fixes: f421436a ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Sending frames via the hsr (master) device requires a sequence number
which is tracked in hsr_priv::sequence_nr and protected by
hsr_priv::seqnr_lock. Each time a new frame is sent, it will obtain a
new id and then send it via the slave devices.
Each time a packet is sent (via hsr_forward_do()) the sequence number is
checked via hsr_register_frame_out() to ensure that a frame is not
handled twice. This make sense for the receiving side to ensure that the
frame is not injected into the stack twice after it has been received
from both slave ports.

There is no locking to cover the sending path which means the following
scenario is possible:

  CPU0				CPU1
  hsr_dev_xmit(skb1)		hsr_dev_xmit(skb2)
   fill_frame_info()             fill_frame_info()
    hsr_fill_frame_info()         hsr_fill_frame_info()
     handle_std_frame()            handle_std_frame()
      skb1's sequence_nr = 1
                                    skb2's sequence_nr = 2
   hsr_forward_do()              hsr_forward_do()

                                   hsr_register_frame_out(, 2)  // okay, send)

    hsr_register_frame_out(, 1) // stop, lower seq duplicate

Both skbs (or their struct hsr_frame_info) received an unique id.
However since skb2 was sent before skb1, the higher sequence number was
recorded in hsr_register_frame_out() and the late arriving skb1 was
dropped and never sent.

This scenario has been observed in a three node HSR setup, with node1 +
node2 having ping and iperf running in parallel. From time to time ping
reported a missing packet. Based on tracing that missing ping packet did
not leave the system.

It might be possible (didn't check) to drop the sequence number check on
the sending side. But if the higher sequence number leaves on wire
before the lower does and the destination receives them in that order
and it will drop the packet with the lower sequence number and never
inject into the stack.
Therefore it seems the only way is to lock the whole path from obtaining
the sequence number and sending via dev_queue_xmit() and assuming the
packets leave on wire in the same order (and don't get reordered by the
NIC).

Cover the whole path for the master interface from obtaining the ID
until after it has been forwarded via hsr_forward_skb() to ensure the
skbs are sent to the NIC in the order of the assigned sequence numbers.

Fixes: f421436a ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The hsr device is a software device. Its
net_device_ops::ndo_start_xmit() routine will process the packet and
then pass the resulting skb to dev_queue_xmit().
During processing, hsr acquires a lock with spin_lock_bh()
(hsr_add_node()) which needs to be promoted to the _irq() suffix in
order to avoid a potential deadlock.
Then there are the warnings in dev_queue_xmit() (due to
local_bh_disable() with disabled interrupts) left.

Instead trying to address those (there is qdisc and…) for netpoll sake,
just disable netpoll on hsr.

Disable netpoll on hsr and replace the _irqsave() locking with _bh().

Fixes: f421436a ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Due to the hashed-MAC optimisation one problem become visible:
hsr_handle_sup_frame() walks over the list of available nodes and merges
two node entries into one if based on the information in the supervision
both MAC addresses belong to one node. The list-walk happens on a RCU
protected list and delete operation happens under a lock.

If the supervision arrives on both slave interfaces at the same time
then this delete operation can occur simultaneously on two CPUs. The
result is the first-CPU deletes the from the list and the second CPUs
BUGs while attempting to dereference a poisoned list-entry. This happens
more likely with the optimisation because a new node for the mac_B entry
is created once a packet has been received and removed (merged) once the
supervision frame has been received.

Avoid removing/ cleaning up a hsr_node twice by adding a `removed' field
which is set to true after the removal and checked before the removal.

Fixes: f266a683 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

hsr_forward_skb() a skb and keeps information in an on-stack
hsr_frame_info. hsr_get_node() assigns hsr_frame_info::node_src which is
from a RCU list. This pointer is used later in hsr_forward_do().
I don't see a reason why this pointer can't vanish midway since there is
no guarantee that hsr_forward_skb() is invoked from an RCU read section.

Use rcu_read_lock() to protect hsr_frame_info::node_src from its
assignment until it is no longer used.

Fixes: f266a683 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The hlist optimisation (which not only uses hlist_head instead of
list_head but also splits hsr_priv::node_db into an array of 256 slots)
does not consider the "node merge":
Upon starting the hsr network (with three nodes) a packet that is
sent from node1 to node3 will also be sent from node1 to node2 and then
forwarded to node3.
As a result node3 will receive 2 packets because it is not able
to filter out the duplicate. Each packet received will create a new
struct hsr_node with macaddress_A only set the MAC address it received
from (the two MAC addesses from node1).
At some point (early in the process) two supervision frames will be
received from node1. They will be processed by hsr_handle_sup_frame()
and one frame will leave early ("Node has already been merged") and does
nothing. The other frame will be merged as portB and have its MAC
address written to macaddress_B and the hsr_node (that was created for
it as macaddress_A) will be removed.
From now on HSR is able to identify a duplicate because both packets
sent from one node will result in the same struct hsr_node because
hsr_get_node() will find the MAC address either on macaddress_A or
macaddress_B.

Things get tricky with the optimisation: If sender's MAC address is
saved as macaddress_A then the lookup will work as usual. If the MAC
address has been merged into macaddress_B of another hsr_node then the
lookup won't work because it is likely that the data structure is in
another bucket. This results in creating a new struct hsr_node and not
recognising a possible duplicate.

A way around it would be to add another hsr_node::mac_list_B and attach
it to the other bucket to ensure that this hsr_node will be looked up
either via macaddress_A _or_ macaddress_B.

I however prefer to revert it because it sounds like an academic problem
rather than real life workload plus it adds complexity. I'm not an HSR
expert with what is usual size of a network but I would guess 40 to 60
nodes. With 10.000 nodes and assuming 60us for pass-through (from node
to node) then it would take almost 600ms for a packet to almost wrap
around which sounds a lot.

Revert the hash MAC addresses optimisation.

Fixes: 4acc45db ("net: hsr: use hlist_head instead of list_head for mac addresses")
Cc: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After commit 9ed7bfc7 ("sctp: fix memory leak in
sctp_stream_outq_migrate()"), sctp_sched_set_sched() is the only
place calling sched->free(), and it can actually be replaced by
sched->free_sid() on each stream, and yet there's already a loop
to traverse all streams in sctp_sched_set_sched().

This patch adds a function sctp_sched_free_sched() where it calls
sched->free_sid() for each stream to replace sched->free() calls
in sctp_sched_set_sched() and then deletes the unused free member
from struct sctp_sched_ops.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/e10aac150aca2686cb0bd0570299ec716da5a5c0.1669849471.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Matthieu Baerts says:

====================
mptcp: PM listener events + selftests cleanup

Thanks to the patch 6/11, the MPTCP path manager now sends Netlink events
when MPTCP listening sockets are created and closed. The reason why it is
needed is explained in the linked ticket [1]:

  MPTCP for Linux, when not using the in-kernel PM, depends on the
  userspace PM to create extra listening sockets before announcing
  addresses and ports. Let's call these "PM listeners".

  With the existing MPTCP netlink events, a userspace PM can create
  PM listeners at startup time, or in response to an incoming connection.
  Creating sockets in response to connections is not optimal: ADD_ADDRs
  can't be sent until the sockets are created and listen()ed, and if all
  connections are closed then it may not be clear to the userspace
  PM daemon that PM listener sockets should be cleaned up.

  Hence this feature request: to add MPTCP netlink events for listening
  socket close & create, so PM listening sockets can be managed based
  on application activity.

  [1] https://github.com/multipath-tcp/mptcp_net-next/issues/313

Selftests for these new Netlink events have been added in patches 9,11/11.

The remaining patches introduce different cleanups and small improvements
in MPTCP selftests to ease the maintenance and the addition of new tests.
====================

Link: https://lore.kernel.org/r/20221130140637.409926-1-matthieu.baerts@tessares.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds test coverage for listening sockets created by the
in-kernel path manager in mptcp_join.sh.

It adds the listener event checking in the existing "remove single
address with port" test. The output looks like this:

 003 remove single address with port syn[ ok ] - synack[ ok ] - ack[ ok ]
                                     add[ ok ] - echo  [ ok ] - pt [ ok ]
                                     syn[ ok ] - synack[ ok ] - ack[ ok ]
                                     syn[ ok ] - ack   [ ok ]
                                     rm [ ok ] - rmsf  [ ok ]   invert
                                     CREATE_LISTENER 10.0.2.1:10100[ ok ]
                                     CLOSE_LISTENER 10.0.2.1:10100 [ ok ]
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch moves evts_ns1 and evts_ns2 out of do_transfer() as two global
variables in mptcp_join.sh. Init them in init() and remove them in
cleanup().

Add a new helper reset_with_events() to save the outputs of 'pm_nl_ctl
events' command in them. And a new helper kill_events_pids() to kill
pids of 'pm_nl_ctl events' command. Use these helpers in userspace pm
tests.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds test coverage for listening sockets created by userspace
processes.

It adds a new test named test_listener() and a new verifying helper
verify_listener_events(). The new output looks like this:

 CREATE_SUBFLOW 10.0.2.2 (ns2) => 10.0.2.1 (ns1)              [OK]
 DESTROY_SUBFLOW 10.0.2.2 (ns2) => 10.0.2.1 (ns1)             [OK]
 MP_PRIO TX                                                   [OK]
 MP_PRIO RX                                                   [OK]
 CREATE_LISTENER 10.0.2.2:37106				      [OK]
 CLOSE_LISTENER 10.0.2.2:37106				      [OK]
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch makes server_evts and client_evts global in userspace_pm.sh,
then these two variables could be used in test_announce(), test_remove()
and test_subflows(). The local variable 'evts' in these three functions
then could be dropped.

Also move local variable 'file' as a global one.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some userspace pm tests failed since pm listener events have been added.
Now MPTCP_EVENT_LISTENER_CREATED event becomes the first item in the
events list like this:

 type:15,family:2,sport:10006,saddr4:0.0.0.0
 type:1,token:3701282876,server_side:1,family:2,saddr4:10.0.1.1,...

And no token value in this MPTCP_EVENT_LISTENER_CREATED event.

This patch fixes this by specifying the type 1 item to search for token
values.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds two new MPTCP netlink event types for PM listening
socket create and close, named MPTCP_EVENT_LISTENER_CREATED and
MPTCP_EVENT_LISTENER_CLOSED.

Add a new function mptcp_event_pm_listener() to push the new events
with family, port and addr to userspace.

Invoke mptcp_event_pm_listener() with MPTCP_EVENT_LISTENER_CREATED in
mptcp_listen() and mptcp_pm_nl_create_listen_socket(), invoke it with
MPTCP_EVENT_LISTENER_CLOSED in __mptcp_close_ssk().
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Just to avoid classical Bash pitfall where variables are accidentally
overridden by other functions because the proper scope has not been
defined.

That's also what is done in other MPTCP selftests scripts where all non
local variables are defined at the beginning of the script and the
others are defined with the "local" keyword.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It is clearer to declare these global variables at the beginning of the
file as it is done in other MPTCP selftests rather than in functions in
the middle of the script.

So for uniformity reason, we can do the same here in mptcp_sockopt.sh.
Suggested-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The definition of 'rndh' was probably copied from one script to another
but some times, 'sec' was not defined, not used and/or not spelled
properly.

Here all the 'rndh' are now defined the same way.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some variables were set but never used.

This was not causing any issues except adding some confusion and having
shellcheck complaining about them.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A new "sandbox" net namespace is available where no other netfilter
rules have been added.

Use this new netns instead of re-using "ns1" and clean it.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

I must have missed that these stats are only exposed
via the unstructured ethtool -S when they got merged.
Plumb in the structured form.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20221130013108.90062-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Arınç ÜNAL says:

====================
remove label = "cpu" from DSA dt-binding

With this patch series, we're completely getting rid of 'label = "cpu";'
which is not used by the DSA dt-binding at all.

Information for taking the patches for maintainers:
Patch 1: netdev maintainers (based off netdev/net-next.git main)
Patch 2-3: SoC maintainers (based off soc/soc.git soc/dt)
Patch 4: MIPS maintainers (based off mips/linux.git mips-next)
Patch 5: PowerPC maintainers (based off powerpc/linux.git next-test)

I've been meaning to submit this for a few months. Find the relevant
conversation here:
https://lore.kernel.org/netdev/20220913155408.GA3802998-robh@kernel.org/

Here's how I did it, for the interested (or suggestions):

Find the platforms which have got 'label = "cpu";' defined.
grep -rnw . -e 'label = "cpu";'

Remove the line where 'label = "cpu";' is included.
sed -i /'label = "cpu";'/,+d arch/arm/boot/dts/*
sed -i /'label = "cpu";'/,+d arch/arm64/boot/dts/freescale/*
sed -i /'label = "cpu";'/,+d arch/arm64/boot/dts/marvell/*
sed -i /'label = "cpu";'/,+d arch/arm64/boot/dts/mediatek/*
sed -i /'label = "cpu";'/,+d arch/arm64/boot/dts/rockchip/*
sed -i /'label = "cpu";'/,+d arch/mips/boot/dts/qca/*
sed -i /'label = "cpu";'/,+d arch/mips/boot/dts/ralink/*
sed -i /'label = "cpu";'/,+d arch/powerpc/boot/dts/turris1x.dts
sed -i /'label = "cpu";'/,+d Documentation/devicetree/bindings/net/qca,ar71xx.yaml

Restore the symlink files which typechange after running sed.
====================

Link: https://lore.kernel.org/r/20221130141040.32447-1-arinc.unal@arinc9.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>