- 16 Oct, 2016 17 commits
-
-
Dan Carpenter authored
commit ac0e89bb upstream. We use logical negate where bitwise negate was intended. It means that we never return -EINVAL here. Fixes: ce11e48b ('KVM: PPC: E500: Add userspace debug stub support') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Alexander Graf <agraf@suse.de> Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Christoffer Dall authored
commit 0099b770 upstream. If the vgic hasn't been created and initialized, we shouldn't attempt to look at its data structures or flush/sync anything to the GIC hardware. This fixes an issue reported by Alexander Graf when using a userspace irqchip. Fixes: 0919e84c ("KVM: arm/arm64: vgic-new: Add IRQ sync/flush framework") Reported-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
-
Christoffer Dall authored
commit 6fe407f2 upstream. If userspace creates a PMU for the VCPU, but doesn't create an in-kernel irqchip, then we end up in a nasty path where we try to take an uninitialized spinlock, which can lead to all sorts of breakages. Luckily, QEMU always creates the VGIC before the PMU, so we can establish this as ABI and check for the VGIC in the PMU init stage. This can be relaxed at a later time if we want to support PMU with a userspace irqchip. Cc: Shannon Zhao <shannon.zhao@linaro.org> Acked-by:
-
James Hogan authored
commit 91e4f1b6 upstream. When a guest TLB entry is replaced by TLBWI or TLBWR, we only invalidate TLB entries on the local CPU. This doesn't work correctly on an SMP host when the guest is migrated to a different physical CPU, as it could pick up stale TLB mappings from the last time the vCPU ran on that physical CPU. Therefore invalidate both user and kernel host ASIDs on other CPUs, which will cause new ASIDs to be generated when it next runs on those CPUs. We're careful only to do this if the TLB entry was already valid, and only for the kernel ASID where the virtual address it mapped is outside of the guest user address range. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by:
-
Thomas Huth authored
commit fa73c3b2 upstream. The MMCR2 register is available twice, one time with number 785 (privileged access), and one time with number 769 (unprivileged, but it can be disabled completely). In former times, the Linux kernel was using the unprivileged register 769 only, but since commit 8dd75ccb ("powerpc: Use privileged SPR number for MMCR2"), it uses the privileged register 785 instead. The KVM-PR code then of course also switched to use the SPR 785, but this is causing older guest kernels to crash, since these kernels still access 769 instead. So to support older kernels with KVM-PR again, we have to support register 769 in KVM-PR, too. Fixes: 8dd75ccbSigned-off-by:
Thomas Huth <thuth@redhat.com> Signed-off-by:
-
Boris Ostrovsky authored
commit a6a198bc upstream. Early during boot topology_update_package_map() computes logical_pkg_ids for all present processors. Later, when processors are brought up, identify_cpu() updates these values based on phys_pkg_id which is a function of initial_apicid. On PV guests the latter may point to a non-existing node, causing logical_pkg_ids to be set to -1. Intel's RAPL uses logical_pkg_id (as topology_logical_package_id()) to index its arrays and therefore in this case will point to index 65535 (since logical_pkg_id is a u16). This could lead to either a crash or may actually access random memory location. As a workaround, we recompute topology during CPU bringup to reset logical_pkg_id to a valid value. (The reason for initial_apicid being bogus is because it is initial_apicid of the processor from which the guest is launched. This value is CPUID(1).EBX[31:24]) Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 88003fb1 upstream. This fixes a compile failure: drivers/built-in.o: In function `wm8350_i2c_probe': core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c' Makefile:953: recipe for target 'vmlinux' failed Fixes: 52b461b8 ("mfd: Add regmap cache support for wm8350") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Dan Carpenter authored
commit 9a6dc644 upstream. set_bit() and clear_bit() take the bit number so this code is really doing "1 << (1 << irq)" which is a double shift bug. It's done consistently so it won't cause a problem unless "irq" is more than 4. Fixes: 70c6cce0 ('mfd: Support 88pm80x in 80x driver') Signed-off-by:
-
Boris Brezillon authored
commit 2c2469bc upstream. readl_poll_timeout() calls usleep_range(), but regmap_atmel_hlcdc_reg_write() is called in atomic context (regmap spinlock held). Replace the readl_poll_timeout() call by readl_poll_timeout_atomic(). Fixes: ea31c0cf ("mfd: atmel-hlcdc: Implement config synchronization") Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Lu Baolu authored
commit 8dcc5ff8 upstream. Member "status" of struct usb_sg_request is managed by usb core. A spin lock is used to serialize the change of it. The driver could check the value of req->status, but should avoid changing it without the hold of the spinlock. Otherwise, it could cause race or error in usb core. This patch could be backported to stable kernels with version later than v3.14. Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Roger Tseng <rogerable@realtek.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
-
Takashi Sakamoto authored
commit 8da08ca0 upstream. Currently, usb-line6 module exports an array of MIDI manufacturer ID and usb-pod module uses it. However, the declaration is not the definition in common header. The difference is explicit length of array. Although compiler calculates it and everything goes well, it's better to use the same representation between definition and declaration. This commit fills the length of array for usb-line6 module. As a small good sub-effect, this commit suppress below warnings from static analysis by sparse v0.5.0. sound/usb/line6/driver.c:274:43: error: cannot size expression sound/usb/line6/driver.c:275:16: error: cannot size expression sound/usb/line6/driver.c:276:16: error: cannot size expression sound/usb/line6/driver.c:277:16: error: cannot size expression Fixes: 705ececd ("Staging: add line6 usb driver") Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Anssi Hannula authored
commit eb1a74b7 upstream. The DragonFly quirk added in 42e3121d ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly") applies a custom dB map on the volume control when its range is reported as 0..50 (0 .. 0.2dB). However, there exists at least one other variant (hw v1.0c, as opposed to the tested v1.2) which reports a different non-sensical volume range (0..53) and the custom map is therefore not applied for that device. This results in all of the volume change appearing close to 100% on mixer UIs that utilize the dB TLV information. Add a fallback case where no dB TLV is reported at all if the control range is not 0..50 but still 0..N where N <= 1000 (3.9 dB). Also restrict the quirk to only apply to the volume control as there is also a mute control which would match the check otherwise. Fixes: 42e3121d ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly") Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Reported-by:
David W <regulars@d-dub.org.uk> Tested-by:
-
Takashi Iwai authored
commit db685779 upstream. The pointer callbacks of ali5451 driver may return the value at the boundary occasionally, and it results in the kernel warning like snd_ali5451 0000:00:06.0: BUG: , pos = 16384, buffer size = 16384, period size = 1024 It seems that folding the position offset is enough for fixing the warning and no ill-effect has been seen by that. Reported-by:
Enrico Mioso <mrkiko.rs@gmail.com> Tested-by:
-
Lu Baolu authored
commit 5e6c88d2 upstream. Commit 50c763f8 ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command") sets ClearPendIN bit for all IN endpoints of v2.60a+ cores. This causes ClearStall command fails on 2.60+ cores operating in HighSpeed mode. In page 539 of 2.60a specification: "When issuing Clear Stall command for IN endpoints in SuperSpeed mode, the software must set the "ClearPendIN" bit to '1' to clear any pending IN transcations, so that the device does not expect any ACK TP from the host for the data sent earlier." It's obvious that we only need to apply this rule to those IN endpoints that currently operating in SuperSpeed mode. Fixes: 50c763f8 ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command") Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
John Stultz authored
commit 58bfea95 upstream. In commit 27727df2 ("Avoid taking lock in NMI path with CONFIG_DEBUG_TIMEKEEPING"), I changed the logic to open-code the timekeeping_get_ns() function, but I forgot to include the unit conversion from cycles to nanoseconds, breaking the function's output, which impacts users like perf. This results in bogus perf timestamps like: swapper 0 [000] 253.427536: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.426573: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.426687: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.426800: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.426905: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.427022: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.427127: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.427239: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.427346: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 254.427463: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 255.426572: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) Instead of more reasonable expected timestamps like: swapper 0 [000] 39.953768: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.064839: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.175956: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.287103: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.398217: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.509324: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.620437: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.731546: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.842654: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 40.953772: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) swapper 0 [000] 41.064881: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms]) Add the proper use of timekeeping_delta_to_ns() to convert the cycle delta to nanoseconds as needed. Thanks to Brendan and Alexei for finding this quickly after the v4.8 release. Unfortunately the problematic commit has landed in some -stable trees so they'll need this fix as well. Many apologies for this mistake. I'll be looking to add a perf-clock sanity test to the kselftest timers tests soon. Fixes: 27727df2 "timekeeping: Avoid taking lock in NMI path with CONFIG_DEBUG_TIMEKEEPING" Reported-by:
Brendan Gregg <bgregg@netflix.com> Reported-by:
Alexei Starovoitov <alexei.starovoitov@gmail.com> Tested-and-reviewed-by:
Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by:
John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/1475636148-26539-1-git-send-email-john.stultz@linaro.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by:
-
Andrew Donnellan authored
commit 6f38a8b9 upstream. When cxl removes a vPHB, it's possible that the pci_controller may be freed before all references to the devices on the vPHB have been released. This in turn causes an invalid memory access when the devices are eventually released, as pcibios_release_device() attempts to call the phb's release_device hook. In cxl_pci_vphb_remove(), remove the existing call to pcibios_free_controller(). Instead, use pcibios_free_controller_deferred() to free the pci_controller after all devices have been released. Export pci_set_host_bridge_release() so we can do this. Signed-off-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Reviewed-by:
Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by:
Ian Munsie <imunsie@au1.ibm.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Mauricio Faria de Oliveira authored
commit 2dd9c11b upstream. This patch leverages 'struct pci_host_bridge' from the PCI subsystem in order to free the pci_controller only after the last reference to its devices is dropped (avoiding an oops in pcibios_release_device() if the last reference is dropped after pcibios_free_controller()). The patch relies on pci_host_bridge.release_fn() (and .release_data), which is called automatically by the PCI subsystem when the root bus is released (i.e., the last reference is dropped). Those fields are set via pci_set_host_bridge_release() (e.g. in the platform-specific implementation of pcibios_root_bridge_prepare()). It introduces the 'pcibios_free_controller_deferred()' .release_fn() and it expects .release_data to hold a pointer to the pci_controller. The function implictly calls 'pcibios_free_controller()', so an user must *NOT* explicitly call it if using the new _deferred() callback. The functionality is enabled for pseries (although it isn't platform specific, and may be used by cxl). Details on not-so-elegant design choices: - Use 'pci_host_bridge.release_data' field as pointer to associated 'struct pci_controller' so *not* to 'pci_bus_to_host(bridge->bus)' in pcibios_free_controller_deferred(). That's because pci_remove_root_bus() sets 'host_bridge->bus = NULL' (so, if the last reference is released after pci_remove_root_bus() runs, which eventually reaches pcibios_free_controller_deferred(), that would hit a null pointer dereference). The cxl/vphb.c code calls pci_remove_root_bus(), and the cxl folks are interested in this fix. Test-case #1 (hold references) # ls -ld /sys/block/sd* | grep -m1 0021:01:00.0 <...> /sys/block/sdaa -> ../devices/pci0021:01/0021:01:00.0/<...> # ls -ld /sys/block/sd* | grep -m1 0021:01:00.1 <...> /sys/block/sdab -> ../devices/pci0021:01/0021:01:00.1/<...> # cat >/dev/sdaa & pid1=$! # cat >/dev/sdab & pid2=$! # drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r Validating PHB DLPAR capability...yes. [ 594.306719] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01 [ 594.306738] pci_hp_remove_devices: Removing 0021:01:00.0... ... [ 598.236381] pci_hp_remove_devices: Removing 0021:01:00.1... ... [ 611.972077] pci_bus 0021:01: busn_res: [bus 01-ff] is released [ 611.972140] rpadlpar_io: slot PHB 33 removed # kill -9 $pid1 # kill -9 $pid2 [ 632.918088] pcibios_free_controller_deferred: domain 33, dynamic 1 Test-case #2 (don't hold references) # drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r Validating PHB DLPAR capability...yes. [ 916.357363] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01 [ 916.357386] pci_hp_remove_devices: Removing 0021:01:00.0... ... [ 920.566527] pci_hp_remove_devices: Removing 0021:01:00.1... ... [ 933.955873] pci_bus 0021:01: busn_res: [bus 01-ff] is released [ 933.955977] pcibios_free_controller_deferred: domain 33, dynamic 1 [ 933.955999] rpadlpar_io: slot PHB 33 removed Suggested-By:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Reviewed-by:
-
- 07 Oct, 2016 23 commits
-
-
Greg Kroah-Hartman authored
-
Takashi Iwai authored
commit 0eec8809 upstream. HP Spectre x360 with CX20724 codec has two speaker outputs while the BIOS sets up only the bottom one (NID 0x17) and disables the top one (NID 0x1d). This patch adds a fixup simply defining the proper pincfg for NID 0x1d so that the top speaker works as is. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=169071Signed-off-by:
-
Hui Wang authored
commit 3f640970 upstream. One of the laptops has the codec ALC256 on it, applying the ALC255_FIXUP_DELL1_MIC_NO_PRESENCE can fix the problem, the rest of laptops have the codec ALC295 on them, they are similar to machines with ALC225, applying the ALC269_FIXUP_DELL1_MIC_NO_PRESENCE can fix the problem. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Hui Wang authored
commit 392c9da2 upstream. We have two new Dell laptop models, they have the same ALC255 pin definition, but not in the pin quirk table yet, as a result, the headset microphone can't work. After adding the definition in the table, the headset microphone works well. Signed-off-by:
-
Greg Kroah-Hartman authored
commit ab21b63e upstream. This reverts commit e6c7efdc. Turns out it was totally wrong. The memory is supposed to be bound to the kref, as the original code was doing correctly, not the device/driver binding as the devm_kzalloc() would cause. This fixes an oops when read would be called after the device was unbound from the driver. Reported-by:
Ladislav Michl <ladis@linux-mips.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Kyle Jones authored
commit decc5360 upstream. Signed-off-by:
Kyle Jones <kyle@kf5jwc.us> Signed-off-by:
-
Nicolas Iooss authored
commit 238b7bd9 upstream. In v_recv_cmd_submit(), urb_p->urb->pipe has the type unsigned int (which is 32-bit long on x86_64) but 11<<30 results in a 34-bit integer. Therefore the 2 leading bits are truncated and urb_p->urb->pipe &= ~(11 << 30); has the same meaning as urb_p->urb->pipe &= ~(3 << 30); This second statement seems to be how the code was intended to be written, as PIPE_ constants have values between 0 and 3. The overflow has been detected with a clang warning: drivers/usb/usbip/vudc_rx.c:145:27: warning: signed shift result (0x2C0000000) requires 35 bits to represent, but 'int' only has 32 bits [-Wshift-overflow] urb_p->urb->pipe &= ~(11 << 30); ~~ ^ ~~ Fixes: 79c02cb1 ("usbip: vudc: Add vudc_rx") Signed-off-by:
Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by:
-
Ksenija Stanojevic authored
commit fc1e2c8e upstream. Commit 367e8560 introduced a bug in fbtft-core where fps is always 0, this is because variable update_time is not assigned correctly. Signed-off-by:
Ksenija Stanojevic <ksenija.stanojevic@gmail.com> Fixes: 367e8560 ("Staging: fbtbt: Replace timespec with ktime_t") Signed-off-by:
-
Greg Kroah-Hartman authored
commit 2fae9e5a upstream. This patch fixes a NULL pointer dereference caused by a race codition in the probe function of the legousbtower driver. It re-structures the probe function to only register the interface after successfully reading the board's firmware ID. The probe function does not deregister the usb interface after an error receiving the devices firmware ID. The device file registered (/dev/usb/legousbtower%d) may be read/written globally before the probe function returns. When tower_delete is called in the probe function (after an r/w has been initiated), core dev structures are deleted while the file operation functions are still running. If the 0 address is mappable on the machine, this vulnerability can be used to create a Local Priviege Escalation exploit via a write-what-where condition by remapping dev->interrupt_out_buffer in tower_write. A forged USB device and local program execution would be required for LPE. The USB device would have to delay the control message in tower_probe and accept the control urb in tower_open whilst guest code initiated a write to the device file as tower_delete is called from the error in tower_probe. This bug has existed since 2003. Patch tested by emulated device. Reported-by:
James Patrick-Evans <james@jmp-e.com> Tested-by:
-
Mikulas Patocka authored
commit 7efb3673 upstream. bio_alloc() can allocate a bio with at most BIO_MAX_PAGES (256) vector entries. However, the incoming bio may have more vector entries if it was allocated by other means. For example, bcache submits bios with more than BIO_MAX_PAGES entries. This results in bio_alloc() failure. To avoid the failure, change the code so that it allocates bio with at most BIO_MAX_PAGES entries. If the incoming bio has more entries, bio_add_page() will fail and a new bio will be allocated - the code that handles bio_add_page() failure already exists in the dm-log-writes target. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Reviewed-by:
Josef Bacik <jbacik@fb.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Jann Horn authored
commit 22f6b4d3 upstream. This ensures that do_mmap() won't implicitly make AIO memory mappings executable if the READ_IMPLIES_EXEC personality flag is set. Such behavior is problematic because the security_mmap_file LSM hook doesn't catch this case, potentially permitting an attacker to bypass a W^X policy enforced by SELinux. I have tested the patch on my machine. To test the behavior, compile and run this: #define _GNU_SOURCE #include <unistd.h> #include <sys/personality.h> #include <linux/aio_abi.h> #include <err.h> #include <stdlib.h> #include <stdio.h> #include <sys/syscall.h> int main(void) { personality(READ_IMPLIES_EXEC); aio_context_t ctx = 0; if (syscall(__NR_io_setup, 1, &ctx)) err(1, "io_setup"); char cmd[1000]; sprintf(cmd, "cat /proc/%d/maps | grep -F '/[aio]'", (int)getpid()); system(cmd); return 0; } In the output, "rw-s" is good, "rwxs" is bad. Signed-off-by:
Jann Horn <jann@thejh.net> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jarkko Sakkinen authored
commit 422eac3f upstream. On my Lenovo x250 the following situation occurs: [18697.813871] tpm_crb MSFT0101:00: can't request region for resource [mem 0xacdff080-0xacdfffff] The mapping of the control area overlaps the mapping of the command buffer. The control area is mapped over page, which is not right. It should mapped over sizeof(struct crb_control_area). Fixing this issue unmasks another issue. Command and response buffers can overlap and they do interleave on this machine. According to the PTP specification the overlapping means that they are mapped to the same buffer. The commit has been also on a Haswell NUC where things worked before applying this fix so that the both code paths for response buffer initialization are tested. Cc: stable@vger.kernel.org Fixes: 1bd047be ("tpm_crb: Use devm_ioremap_resource") Signed-off-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
-
Jarkko Sakkinen authored
commit 14ddfbf4 upstream. The iomem resource is needed only temporarily so it is better to pass it on instead of storing it permanently. Named the variable as io_res so that the code better documents itself. Signed-off-by:
Stefan Berger <stefanb@linux.vnet.ibm.com> Signed-off-by:
-
Marek Lindner authored
commit d9f17987 upstream. Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
-
Maor Gottlieb authored
commit ee3da804 upstream. Set the source mac address in the FTE when L2 specification is provided. Fixes: 038d2ef8 ('IB/mlx5: Add flow steering support') Signed-off-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Noa Osherovich authored
commit 7fae6655 upstream. MAD_IFC command is supported only for physical functions (PF) and when physical port is IB. The proposed fix enforces it. Fixes: d603c809 ("IB/mlx5: Fix decision on using MAD_IFC") Reported-by:
David Chang <dchang@suse.com> Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
commit 8ec07bf8 upstream. When sending QP1 MAD packets which use a GRH, the source GID (which consists of the 64-bit subnet prefix, and the 64 bit port GUID) must be included in the packet GRH. For SR-IOV, a GID cache is used, since the source GID needs to be the slave's source GID, and not the Hypervisor's GID. This cache also included a subnet_prefix. Unfortunately, the subnet_prefix field in the cache was never initialized (to the default subnet prefix 0xfe80::0). As a result, this field remained all zeroes. Therefore, when SR-IOV was active, all QP1 packets which included a GRH had a source GID subnet prefix of all-zeroes. However, the subnet-prefix should initially be 0xfe80::0 (the default subnet prefix). In addition, if OpenSM modifies a port's subnet prefix, the new subnet prefix must be used in the GRH when sending QP1 packets. To fix this we now initialize the subnet prefix in the SR-IOV GID cache to the default subnet prefix. We update the cached value if/when OpenSM modifies the port's subnet prefix. We take this cached value when sending QP1 packets when SR-IOV is active. Note that the value is stored as an atomic64. This eliminates any need for locking when the subnet prefix is being updated. Note also that we depend on the FW generating the "port management change" event for tracking subnet-prefix changes performed by OpenSM. If running early FW (before 2.9.4630), subnet prefix changes will not be tracked (but the default subnet prefix still will be stored in the cache; therefore users who do not modify the subnet prefix will not have a problem). IF there is a need for such tracking also for early FW, we will add that capability in a subsequent patch. Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
-
Jack Morgenstein authored
commit baa0be70 upstream. The indentation in the QP1 GRH flow in procedure build_mlx_header is really confusing. Fix it, in preparation for a commit which touches this code. Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support") Signed-off-by:
-
Alex Vesker authored
commit e5ac40cd upstream. Because of an incorrect bit-masking done on the join state bits, when handling a join request we failed to detect a difference between the group join state and the request join state when joining as send only full member (0x8). This caused the MC join request not to be sent. This issue is relevant only when SRIOV is enabled and SM supports send only full member. This fix separates scope bits and join states bits a nibble each. Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV') Signed-off-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
-
Alex Vesker authored
commit 344bacca upstream. This fix solves a race between light flush and on the fly joins. Light flush doesn't set the device to down and unset IPOIB_OPER_UP flag, this means that if while flushing we have a MC join in progress and the QP was attached to BC MGID we can have a mismatches when re-attaching a QP to the BC MGID. The light flush would set the broadcast group to NULL causing an on the fly join to rejoin and reattach to the BC MCG as well as adding the BC MGID to the multicast list. The flush process would later on remove the BC MGID and detach it from the QP. On the next flush the BC MGID is present in the multicast list but not found when trying to detach it because of the previous double attach and single detach. [18332.714265] ------------[ cut here ]------------ [18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core] ... [18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011 [18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000 [18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300 [18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280 [18332.796199] Call Trace: [18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c [18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0 [18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20 [18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core] [18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib] [18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib] [18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib] [18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib] [18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0 [18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40 [18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80 [18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib] [18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib] [18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30 [18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50 [18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170 [18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0 [18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50 [18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0 [18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0 [18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0 [18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25 [18332.894727] ---[ end trace 09ebbe31f831ef17 ]--- Fixes: ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM change events") Signed-off-by:
-
Johannes Thumshirn authored
commit 835831c5 upstream. Use scsi_is_sas_rphy() instead of is_sas_attached() to decide whether we should obtain the SAS address from a scsi device or not. This will prevent us from tripping on the BUG_ON() in sas_sdev_to_rdev() if the rphy isn't attached to the SAS transport class, like it is with hpsa's logical devices. Fixes: 3f8d6f2a ('ses: fix discovery of SATA devices in SAS enclosures') Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
James E.J. Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Johannes Thumshirn authored
commit c1a23f6d upstream. Provide a stub implementation for scsi_is_sas_rphy for kernel configurations which do not have CONFIG_SCSI_SAS_ATTRS defined. Reported-by:
kbuild test robot <lkp@intel.com> Suggested-by:
-
Lars-Peter Clausen authored
commit 1bc8da4e upstream. When searching for a suitable node that should be used for inserting a new register, which does not fall within the range of any existing node, we not only looks for nodes which are directly adjacent to the new register, but for nodes within a certain proximity. This is done to avoid creating lots of small nodes with just a few registers spacing in between, which would increase memory usage as well as tree traversal time. This means there might be multiple node candidates which fall within the proximity range of the new register. If we choose the first node we encounter, under certain register insertion patterns it is possible to end up with overlapping ranges. This will break order in the rbtree and can cause the cached register value to become corrupted. E.g. take the simplified example where the proximity range is 2 and the register insertion sequence is 1, 4, 2, 3, 5. * Insert of register 1 creates a new node, this is the root of the rbtree * Insert of register 4 creates a new node, which is inserted to the right of the root. * Insert of register 2 gets inserted to the first node * Insert of register 3 gets inserted to the first node * Insert of register 5 also gets inserted into the first node since this is the first node encountered and it is within the proximity range. Now there are two overlapping nodes. To avoid this always choose the node that is closest to the new register. This will ensure that nodes will not overlap. The tree traversal is still done as a binary search, we just don't stop at the first node found. So the complexity of the algorithm stays within the same order. Ideally if a new register is in the range of two adjacent blocks those blocks should be merged, but that is a much more invasive change and left for later. The issue was initially introduced in commit 472fdec7 ("regmap: rbtree: Reduce number of nodes, take 2"), but became much more exposed by commit 6399aea6 ("regmap: rbtree: When adding a reg do a bsearch for target node") which changed the order in which nodes are looked-up. Fixes: 6399aea6 ("regmap: rbtree: When adding a reg do a bsearch for target node") Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
