On my 855 machine the BIOS uses the following DPLL settings:
DPLL 0x90016000
FP0 = 0x61207
FP1 = 0x21207

With the 66MHz SSC refclock, that puts the BIOS generated VCO
frequency at ~908 MHz, which is lower than the 930 MHz limit
we have currently. This also results in the pixel clock coming
out significantly higher than the requested 65 MHz when we try
to recompute it.

Reduce the the VCO limit to 908 MHz. Combined with the earlier
SSC reference clock accuracy fix, this results in the pixel clock
coming out as 65.08 MHz which is quite close to the target. For
some reason the BIOS uses 64.881 MHz, which isn't quite as close.

This makes kms_flip wf_vblank-ts-check pass for the first time
on this machine \o/

Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Store the SSC refclock frequency in kHz to get more accuracy. Currently
we're pretending that 66 MHz is ~66000 kHz, when in fact it is actually
~66667 kHz. By storing the less rounded kHz value we get a much better
accuracy for out pixel clock calculations.

Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.

The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa

The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207

That puts the BIOS generated VCO frequency at 1512 MHz, which is
higher than the 1400 MHz limit we have currently.

Let's bump the VCO limit to 1512 MHz and see what happens.

Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.

The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa

The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207

We can't generate that pixel clock currently as we're limiting the N
divider to at least 3, whereas the BIOS uses a value of 2.

Let's reduce the N minimum to 2 and see what happens.

Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

In order to determine the correct p2 divider for LVDS on gen2,
we need to check the CLKB mode from the LVDS port register to
determine if we're dealing with single or dual channel LVDS.

Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Every ring seems to have a BB_ADDR registers, so include them all in the
error state.

v2: Also include the _UDW on BDW
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The BB_ADDR register is documented to be 32bits at least since SNB.
Prior to that the high 32bits were listed as MBZ, so using a 64bit read
doesn't seem worth anything. Also the simulator doesn't like the 64bit
read. So just switch to using a 32bit read instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If we're disabling the VDD override bit and the panel is enabled, we
don't need to wait for anything. If the panel is disabled, then we
need to actually wait for panel_power_cycle_delay, not
panel_power_down_delay, because the power down delay was already
respected when we disabled the panel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

I don't see a reason to touch VDD when we're disabling the panel:
since the panel is enabled, we don't need VDD. This saves a few sleep
calls from the vdd_on and vdd_off functions at every modeset.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69693Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix the patch mangle wiggle has done ... Spotted by Paulo.
Also drop the runtime_pm_put call which now has to go due to different
patch ordering. Also from Paul.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We just don't need this. This saves 250ms from every modeset on my
machine.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The code to enable/disable PC8 already takes care of saving and
restoring all the registers we need to save/restore, so do a put()
call when we enable PC8 and a get() call when we disable it.

Ideally, in order to make it easier to add runtime PM support to other
platforms, we should move some things from the PC8 code to the runtime
PM code, but let's do this later, since we can make Haswell work right
now.

V2: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Don't actually enable runtime pm since I didn't merge all
patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The plan is to merge PC8 and D3 into a single feature, and when we're
in D3 we won't get any hotplug interrupt anyway, so leaving them
enable doesn't make sense, and it also brings us a problem. The
problem is that we get a hotplug interrupt right when we we wake up
from D3, when we're still waking up everything. If we fully disable
interrupts we won't get this hotplug interrupt, so we won't have
problems.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The current code was checking if all bits of "val" were enabled and
DE_PCH_EVENT_IVB was disabled. The new code doesn't care about the
state of DE_PCH_EVENT_IVB: it just checks if everything else is 1.

The goal is that future patches may completely disable interrupts, and
the LCPLL-disabling code shouldn't care about the state of
DE_PCH_EVENT_IVB.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: I think the commit message is actually wrong in it's
description of what the old test checked, but the new one seems sane.
So meh.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

And put it when it's off. Otherwise, when you run pm_pc8 from
intel-gpu-tools, and the delayed function that disables VDD runs,
we'll get some messages saying we're touching registers while the HW
is suspended.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

These are needed when we cat the debugfs and sysfs files.

V2: - Rebase
V3: - Rebase
V4: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If I add code to enable runtime PM on my Haswell machine, start a
desktop environment, then enable runtime PM, these functions will
complain that they're trying to read/write registers while the
graphics card is suspended.

v2: - Simplify i915_gem_fault changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the hunk in i915_hangcheck_elapsed, it's the wrong thing
to do.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Now that we are actually setting the device to the D3 state, we should
issue the notification.

The opregion spec says we should send the message before the adapter
is about to be placed in a lower power state, and after the adapter is
placed in a higher power state.

Jani originally wrote a similar patch for PC8, but then we discovered
that we were not really changing the PCI D states when
enabling/disabling PC8, so we had to postpone his patch.

v2: - Improve commit message, explaining the expected state.

v3: - Rebase.

Cc: Jani Nikula <jani.nikula@intel.com>
Credits-to: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.

We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.

V2: - Move some functions to intel_pm.c
    - Remove useless pm_runtime_allow() call at init
    - Remove useless pm_runtime_mark_last_busy() call at get
    - Use pm_runtime_get_sync() instead of 2 calls
    - Add a WARN to check if we're really awake

V3: - Rebase.

V4: - Don't need to call pci_{save,restore}_state and
      pci_set_power_sate, since they're already called by the PCI
      layer
    - Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

In the current code, at haswell_modeset_global_resources, first we
decide if we want to enable/disable the power well, then we decide if
we want to enable/disable PC8. On the case where we're enabling PC8
this works fine, but on the case where we disable PC8 due to a non-eDP
monitor being enabled, we first enable the power well and then disable
PC8. Although wrong, this doesn't seem to be causing any problems now,
and we don't even see anything in dmesg. But the patches for runtime
D3 turn this problem into a real bug, so we need to fix it.

This fixes the "modeset-non-lpsp" subtest from the "pm_pc8" test from
intel-gpu-tools.

v2: - Rebase (i915_disable_power_well).
v3: - More reabase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We already have some checks and shouldn't be reaching these places on
!HAS_PC8 platforms, but add a WARN,  just in case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The CRI clock is related to the display PHY, so the setup belongs
in intel_init_dpio().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We don't modify the packed infoframe data, so we should keep the
const qualifier in place. Just pass the buffer as 'const void *'
instead of 'const uint8_t *' and we can drop the cast entirely.

v2: Do intel_sdvo_write_infoframe() as well
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If one mode of a internal panel has more than one refresh rate, then a reduced
clock is found for the LFP (LVDS/eDP). This enables switching between low
and high frequency dynamically. Moving downclock calculation to intel_panel
so that it is common for LVDS and eDP.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Since early sanitize and uncore sanitize are called one after the other,
I think, we can remove second forcewake reset which was are calling
twice in both the functions.

Note that this is merge fallout between

commit ef46e0d2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sat Nov 16 16:00:09 2013 +0100

    drm/i915: restore the early forcewake cleanup

and

commit 521198a2
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Fri Aug 23 16:52:30 2013 +0300

    drm/i915: sanitize forcewake registers on reset
Signed-off-by: Deepak S <deepak.s@intel.com>
[danvet: Explain how this came to be.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Linux 3.13-rc3

I need a backmerge for two reasons:
- For merging the ppgtt patches from Ben I need to pull in the bdw
  support.
- We now have duplicated calls to intel_uncore_forcewake_reset in the
  setup code to due 2 different patches merged into -next and 3.13.
  The conflict is silen so I need the merge to be able to apply
  Deepak's fixup patch.

Conflicts:
	drivers/gpu/drm/i915/intel_display.c

Trivial conflict, it doesn't even show up in the merge diff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Currently, PC8 is enabled at modeset_global_resources, which is called
after intel_modeset_update_state. Due to this, there's a small race
condition on the case where we start enabling PC8, then do a modeset
while PC8 is still being enabled. The racing condition triggers a WARN
because intel_modeset_update_state will mark the CRTC as enabled, then
the thread that's still enabling PC8 might look at the data structure
and think that PC8 is being enabled while a pipe is enabled. Despite
the WARN, this is not really a bug since we'll wait for the
PC8-enabling thread to finish when we call modeset_global_resources.

The spec says the CRTC cannot be enabled when we disable LCPLL, so we
had a check for crtc->base.enabled. If we change to crtc->active we
will still prevent disabling LCPLL while the CRTC is enabled, and we
will also prevent the WARN above.

This is a replacement for the previous patch named
    "drm/i915: get/put PC8 when we get/put a CRTC"

Testcase: igt/pm_pc8/modeset-lpsp-stress-no-wait
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fix from Steven Rostedt:
 "A regression showed up that there's a large delay when enabling all
  events.  This was prevalent when FTRACE_SELFTEST was enabled which
  enables all events several times, and caused the system bootup to
  pause for over a minute.

  This was tracked down to an addition of a synchronize_sched()
  performed when system call tracepoints are unregistered.

  The synchronize_sched() is needed between the unregistering of the
  system call tracepoint and a deletion of a tracing instance buffer.
  But placing the synchronize_sched() in the unreg of *every* system
  call tracepoint is a bit overboard.  A single synchronize_sched()
  before the deletion of the instance is sufficient"

* tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Only run synchronize_sched() at instance deletion time

Pull aio fix from Benjamin LaHaise:
 "AIO fix from Gu Zheng that fixes a GPF that Dave Jones uncovered with
  trinity"

* git://git.kvack.org/~bcrl/aio-next:
  aio: clean up aio ring in the fail path

Pull SCSI fixes from James Bottomley:
 "This is a set of nine fixes (and one author update).

  The libsas one should fix discovery in eSATA devices, the WRITE_SAME
  one is the largest, but it should fix a lot of problems we've been
  getting with the emulated RAID devices (they've been effectively lying
  about support and then firmware has been choking on the commands).

  The rest are various crash, hang or warn driver fixes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] bfa: Fix crash when symb name set for offline vport
  [SCSI] enclosure: fix WARN_ON in dual path device removing
  [SCSI] pm80xx: Tasklets synchronization fix.
  [SCSI] pm80xx: Resetting the phy state.
  [SCSI] pm80xx: Fix for direct attached device.
  [SCSI] pm80xx: Module author addition
  [SCSI] hpsa: return 0 from driver probe function on success, not 1
  [SCSI] hpsa: do not discard scsi status on aborted commands
  [SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
  [SCSI] libsas: fix usage of ata_tf_to_fis

Pull IMA fixes from James Morris:
 "Here are two more fixes for IMA"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  ima: properly free ima_template_entry structures
  ima: Do not free 'entry' before it is initialized

Pull devicetree fixes from Rob Herring:
 - Various DT binding documentation updates
 - Add Kumar Gala and remove Stephen Warren as DT binding maintainers

* tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt: binding: reword PowerPC 8xxx GPIO documentation
  ARM: tegra: delete nvidia,tegra20-spi.txt binding
  hwmon: ntc_thermistor: Fix typo (pullup-uV -> pullup-uv)
  of: add vendor prefix for GMT
  clk: exynos: Fix typos in DT bindings documentation
  of: Add vendor prefix for LG Corporation
  Documentation: net: fsl-fec.txt: Add phy-supply entry
  ARM: dts: doc: Document missing binding for omap5-mpu
  dt-bindings: add ARMv8 PMU binding
  MAINTAINERS: remove swarren from DT bindings
  MAINTAINERS: Add Kumar to Device Tree Binding maintainers group

Clean up the aio ring file in the fail path of aio_setup_ring
and ioctx_alloc. And maybe it can fix the GPF issue reported by
Dave Jones:
https://lkml.org/lkml/2013/11/25/898Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>

Merge branch 'free-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity into for-linus

Pull power management fixes from Rafael Wysocki:

 - cpufreq regression fix from Bjørn Mork restoring the pre-3.12
   behavior of the framework during system suspend/hibernation to avoid
   garbage sysfs files from being left behind in case of a suspend error

 - PNP regression fix to restore the correct states of devices after
   resume from hibernation broken in 3.12.  From Dmitry Torokhov.

 - cpuidle fix to prevent cpuidle device unregistration from crashing
   due to a NULL pointer dereference if cpuidle has been disabled from
   the kernel command line.  From Konrad Rzeszutek Wilk.

 - intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
   processors from Arne Bockholdt.

 - Power capping framework fix to make the energy_uj sysfs attribute
   work in accordance with the documentation.  From Srinivas Pandruvada.

 - epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
   been compiled with CONFIG_PM_SLEEP unset (in which case that flag
   should not have any effect).  From Amit Pundir.

 - cpufreq fix to prevent governor sysfs files from being lost over
   system suspend/resume in some (arguably unusual) situations.  From
   Viresh Kumar.

* tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PowerCap: Fix mode for energy counter
  PNP: fix restoring devices after hibernation
  cpuidle: Check for dev before deregistering it.
  epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
  cpufreq: fix garbage kobjects on errors during suspend/resume
  cpufreq: suspend governors on system suspend/hibernate
  intel_idle: Fixed C6 state on Avoton/Rangeley processors

* pm-epoll:
  epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled

* pnp:
  PNP: fix restoring devices after hibernation

* powercap:
  PowerCap: Fix mode for energy counter

* pm-cpuidle:
  cpuidle: Check for dev before deregistering it.
  intel_idle: Fixed C6 state on Avoton/Rangeley processors

* pm-cpufreq:
  cpufreq: fix garbage kobjects on errors during suspend/resume
  cpufreq: suspend governors on system suspend/hibernate

Pull arch/tile ftrace bug fix from Chris Metcalf:
 "This fixes a build failure with allyesconfig reported by Fengguang Wu
  and fixed by Tony Lu"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  ftrace: default to tilegx if ARCH=tile is specified

Pull block layer fixes from Jens Axboe:
 "A small collection of fixes for the current series. It contains:

   - A fix for a use-after-free of a request in blk-mq.  From Ming Lei

   - A fix for a blk-mq bug that could attempt to dereference a NULL rq
     if allocation failed

   - Two xen-blkfront small fixes

   - Cleanup of submit_bio_wait() type uses in the kernel, unifying
     that.  From Kent

   - A fix for 32-bit blkg_rwstat reading.  I apologize for this one
     looking mangled in the shortlog, it's entirely my fault for missing
     an empty line between the description and body of the text"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: fix use-after-free of request
  blk-mq: fix dereference of rq->mq_ctx if allocation fails
  block: xen-blkfront: Fix possible NULL ptr dereference
  xen-blkfront: Silence pfn maybe-uninitialized warning
  block: submit_bio_wait() conversions
  Update of blkg_stat and blkg_rwstat may happen in bh context

Pull NFS client bugfixes from Trond Myklebust:
 - Stable fix for a NFSv4.1 delegation and state recovery deadlock
 - Stable fix for a loop on irrecoverable errors when returning
   delegations
 - Fix a 3-way deadlock between layoutreturn, open, and state recovery
 - Update the MAINTAINERS file with contact information for Trond
   Myklebust
 - Close needs to handle NFS4ERR_ADMIN_REVOKED
 - Enabling v4.2 should not recompile nfsd and lockd
 - Fix a couple of compile warnings

* tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs: fix do_div() warning by instead using sector_div()
  MAINTAINERS: Update contact information for Trond Myklebust
  NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
  SUNRPC: do not fail gss proc NULL calls with EACCES
  NFSv4: close needs to handle NFS4ERR_ADMIN_REVOKED
  NFSv4: Update list of irrecoverable errors on DELEGRETURN
  NFSv4 wait on recovery for async session errors
  NFS: Fix a warning in nfs_setsecurity
  NFS: Enabling v4.2 should not recompile nfsd and lockd