- 02 Jun, 2021 40 commits
-
-
Mike Christie authored
Subsequent commits allow the kernel to do ep_disconnect. In that case we will have to get a proper refcount on the ep so one thread does not delete it from under another. Link: https://lore.kernel.org/r/20210525181821.7617-7-michael.christie@oracle.comReviewed-by:
Lee Duncan <lduncan@suse.com> Signed-off-by:
Mike Christie <michael.christie@oracle.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Mike Christie authored
Use the system_unbound_wq for async session destruction. We don't need a dedicated workqueue for async session destruction because: 1. perf does not seem to be an issue since we only allow 1 active work. 2. it does not have deps with other system works and we can run them in parallel with each other. Link: https://lore.kernel.org/r/20210525181821.7617-6-michael.christie@oracle.comReviewed-by: -
Mike Christie authored
If the system is not up, we can just fail immediately since iscsid is not going to ever answer our netlink events. We are already setting the recovery_tmo to 0, but by passing stop_conn STOP_CONN_TERM we never will block the session and start the recovery timer, because for that flag userspace will do the unbind and destroy events which would remove the devices and wake up and kill the eh. Since the conn is dead and the system is going dowm this just has us use STOP_CONN_RECOVER with recovery_tmo=0 so we fail immediately. However, if the user has set the recovery_tmo=-1 we let the system hang like they requested since they might have used that setting for specific reasons (one known reason is for buggy cluster software). Link: https://lore.kernel.org/r/20210525181821.7617-5-michael.christie@oracle.comSigned-off-by:
-
Mike Christie authored
libiscsi will now suspend the send/tx queue for the drivers so we can drop it from the drivers ep_disconnect. Link: https://lore.kernel.org/r/20210525181821.7617-4-michael.christie@oracle.comReviewed-by:
-
Mike Christie authored
During ep_disconnect we have been doing iscsi_suspend_tx/queue to block new I/O but every driver except cxgbi and iscsi_tcp can still get I/O from __iscsi_conn_send_pdu() if we haven't called iscsi_conn_failure() before ep_disconnect. This could happen if we were terminating the session, and the logout timed out before it was even sent to libiscsi. Fix the issue by adding a helper which reverses the bind_conn call that allows new I/O to be queued. Drivers implementing ep_disconnect can use this to make sure new I/O is not queued to them when handling the disconnect. Link: https://lore.kernel.org/r/20210525181821.7617-3-michael.christie@oracle.comReviewed-by:
-
Mike Christie authored
This adds a helper to detect if a cmd has completed but is not yet freed. Link: https://lore.kernel.org/r/20210525181821.7617-2-michael.christie@oracle.comReviewed-by:
-
Chandrakanth Patil authored
Link: https://lore.kernel.org/r/20210528131307.25683-6-chandrakanth.patil@broadcom.comSigned-off-by:
Chandrakanth Patil <chandrakanth.patil@broadcom.com> Signed-off-by:
-
Chandrakanth Patil authored
While reenabling the IRQ after IRQ poll there may be a small window for the firmware to post the replies with interrupts raised. In that case the driver will not see the interrupts which leads to I/O timeout. This issue only happens when there are many I/O completions on a single reply queue. This forces the driver to switch between the interrupt and IRQ context. Make the driver process the reply queue one more time after enabling the IRQ. Link: https://lore.kernel.org/linux-scsi/20201102072746.27410-1-sreekanth.reddy@broadcom.com/ Link: https://lore.kernel.org/r/20210528131307.25683-5-chandrakanth.patil@broadcom.com Cc: Tomas Henzl <thenzl@redhat.com> Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by:
-
Kashyap Desai authored
Consider the case where a VD is deleted and the targetID of that VD is assigned to a newly created VD. If the sequence of deletion/addition of VD happens very quickly there is a possibility that second event (VD add) occurs even before the driver processes the first event (VD delete). As event processing is done in deferred context the device list remains the same (but targetID is re-used) so driver will not learn the VD deletion/additon. I/Os meant for the older VD will be directed to new VD which may lead to data corruption. Make driver detect the deleted VD as soon as possible based on the RaidMap update and block further I/O to that device. Link: https://lore.kernel.org/r/20210528131307.25683-4-chandrakanth.patil@broadcom.comReported-by:
Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by:
-
Chandrakanth Patil authored
The driver doesn't clean up all the allocated resources properly when scsi_add_host(), megasas_start_aen() function fails during the PCI device probe. Clean up all those resources. Link: https://lore.kernel.org/r/20210528131307.25683-3-chandrakanth.patil@broadcom.comSigned-off-by:
-
Chandrakanth Patil authored
The driver issues all non-ReadWrite I/Os for TYPE_ENCLOSURE devices through the fast path with invalid dev handle. Fast path in turn directs all the I/Os to the firmware. As firmware stopped handling those I/Os from SAS3.5 generation of controllers (Ventura generation and onwards) this will lead to I/O failures. Switch the driver to issue all the non-ReadWrite I/Os for TYPE_ENCLOSURE devices directly to firmware for SAS3.5 generation of controllers and later. Link: https://lore.kernel.org/r/20210528131307.25683-2-chandrakanth.patil@broadcom.com Cc: <stable@vger.kernel.org> # v5.11+ Signed-off-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-25-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
Hannes Reinecke <hare@suse.de> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Reviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-24-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Read PCI_EXT_CAP_ID_DSN to query security status. The driver will throw a warning message when a non-secure type controller is detected. The purpose of this interface is to avoid interacting with any firmware which is not secured/signed by Broadcom. Any tampering on firmware component will be detected by hardware and it will be communicated to the driver to avoid any further interaction with that component. Link: https://lore.kernel.org/r/20210520152545.2710479-23-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-22-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Wait for host I/O completion (default 180 seconds) if I/O timeout is detected on VDs. Link: https://lore.kernel.org/r/20210520152545.2710479-21-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-20-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Unlock the host diagnostic register, write the specific reset type to that and wait for reset acknowledgment from the controller. If the reset is not successful retry for the predefined number of times Link: https://lore.kernel.org/r/20210520152545.2710479-19-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Register driver for threaded interrupts. By default the driver will attempt I/O completion from interrupt context (primary handler). Since the driver tracks per reply queue outstanding I/Os, it will schedule threaded ISR if there are any outstanding I/Os expected on that particular reply queue. Threaded ISR (secondary handler) will loop for I/O completion as long as there are outstanding I/Os (speculative method using same per reply queue outstanding counter) or it has completed some X amount of commands (something like budget). Link: https://lore.kernel.org/r/20210520152545.2710479-18-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
The controller hardware can not handle certain UNMAP commands for NVMe drives. Add support in the driver for checking those commands and handle them appropriately. Link: https://lore.kernel.org/r/20210520152545.2710479-17-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Instead of driver returning DID_NO_CONNECT during driver unload allow SSU and Sync Cache commands to be sent to the controller to flush any cached data from the drive. Link: https://lore.kernel.org/r/20210520152545.2710479-16-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-15-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-14-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Cc: hare@suse.de Cc: thenzl@redhat.com Reviewed-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-13-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Link: https://lore.kernel.org/r/20210520152545.2710479-12-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
This operation requests that the IOC update the TimeStamp. When the I/O Unit is powered on it sets the TimeStamp field value to 0x0000_0000_0000_0000 and increments the current value every millisecond. A host driver sets the TimeStamp field to the current time by using an IOCInit request. The TimeStamp field is periodically updated by the host driver. Link: https://lore.kernel.org/r/20210520152545.2710479-11-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Detection of firmware fault or any kind of unresponsiveness in the controller (any admin command which times out) results in resetting the controller. The primary reset mechanisms used are either soft reset or diag fault reset. A reset is performed if the host sets the ResetAction field in the HostDiagnostic register to either 001b (soft reset) or 007b (diag fault reset). After successfully resetting the controller the driver reinitializes the controller by going through start of the day initialization procedure. Pending I/Os during the reset are returned back to the SCSI midlayer for retry. Link: https://lore.kernel.org/r/20210520152545.2710479-10-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.co Reviewed-by:
-
Kashyap Desai authored
Implement support for handling the following MPI events: - MPI3_EVENT_SAS_BROADCAST_PRIMITIVE - MPI3_EVENT_CABLE_MGMT - MPI3_EVENT_ENERGY_PACK_CHANGE Link: https://lore.kernel.org/r/20210520152545.2710479-9-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Implement support for the following PCIe-related MPI events: - MPI3_EVENT_PCIE_TOPOLOGY_CHANGE_LIST - MPI3_EVENT_PCIE_ENUMERATION Link: https://lore.kernel.org/r/20210520152545.2710479-8-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Firmware can report various MPI Events. Enable support for processing the following events related to device addition/removal to the driver: - MPI3_EVENT_DEVICE_ADDED - MPI3_EVENT_DEVICE_INFO_CHANGED - MPI3_EVENT_DEVICE_STATUS_CHANGE - MPI3_EVENT_ENCL_DEVICE_STATUS_CHANGE - MPI3_EVENT_SAS_TOPOLOGY_CHANGE_LIST - MPI3_EVENT_SAS_DISCOVERY - MPI3_EVENT_SAS_DEVICE_DISCOVERY_ERROR Link: https://lore.kernel.org/r/20210520152545.2710479-7-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reported-by:
-
Kashyap Desai authored
The watchdog thread is the driver's internal thread which does a few things such as detecting firmware faults, resetting the controller, performing timestamp sync, etc. Link: https://lore.kernel.org/r/20210520152545.2710479-6-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Send Port Enable Request to FW for Device Discovery. As part of port enable completion driver calls scan_start and scan_finished hooks. SCSI layer references like sdev, starget, etc. are added but actual device discovery will be supported once driver adds complete event process handling. Link: https://lore.kernel.org/r/20210520152545.2710479-5-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Cc: hare@suse.de Reviewed-by:
-
Kashyap Desai authored
Create operational request and reply queue pair. The MPI3 transport interface consists of an Administrative Request Queue, an Administrative Reply Queue, and Operational Messaging Queues. The Operational Messaging Queues are the primary communication mechanism between the host and the I/O Controller (IOC). Request messages, allocated in host memory, identify I/O operations to be performed by the IOC. These operations are queued on an Operational Request Queue by the host driver. Reply descriptors track I/O operations as they complete. The IOC queues these completions in an Operational Reply Queue. To fulfil large contiguous memory requirement, driver creates multiple segments and provide the list of segments. Each segment size should be 4K which is a hardware requirement. An element array is contiguous or segmented. A contiguous element array is located in contiguous physical memory. A contiguous element array must be aligned on an element size boundary. An element's physical address within the array may be directly calculated from the base address, the Producer/Consumer index, and the element size. Expected phased identifier bit is used to find out valid entry on reply queue. Driver sets <ephase> bit and IOC inverts the value of this bit on each pass. Link: https://lore.kernel.org/r/20210520152545.2710479-4-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Reviewed-by:
-
Kashyap Desai authored
Implement basic pci device driver requirements: Device probing, memory allocation, mapping system registers, allocate irq lines, etc. Source is managed in mainly three different files: - mpi3mr_fw.c: Common code which interacts with underlying fw/hw. - mpi3mr_os.c: Common code which interacts with SCSI midlayer. - mpi3mr_app.c: Common code which interacts with application/ioctl. This is currently work in progress. Link: https://lore.kernel.org/r/20210520152545.2710479-3-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Cc: bvanassche@acm.org Reviewed-by:
-
Kashyap Desai authored
This adds the Kconfig and mpi30 headers. Link: https://lore.kernel.org/r/20210520152545.2710479-2-kashyap.desai@broadcom.com Cc: sathya.prakash@broadcom.com Cc: bvanassche@acm.org Cc: hch@infradead.org Reviewed-by:
-
Bean Huo authored
Fix the following W=1 kernel build warning: drivers/scsi/ufs/ufshcd.c:9773: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst [mkp: upcase abbreviations] Link: https://lore.kernel.org/r/20210531163122.451375-1-huobean@gmail.comReviewed-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
Bean Huo <beanhuo@micron.com> Signed-off-by:
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), avoid intentionally writing across neighboring array fields. Switch from rsp_ui to resp_buf, since resp_ui isn't SSP_RESP_IU_MAX_SIZE bytes in length. This avoids future compile-time warnings. Link: https://lore.kernel.org/r/20210528181337.792268-4-keescook@chromium.orgReviewed-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), avoid intentionally writing across neighboring array fields. Remove old-style 1-byte array in favor of a flexible array[1] to avoid future false-positive cross-field memcpy() warning in: esas2r_vda.c: memcpy(vi->cmd.gsv.version_info, esas2r_vdaioctl_versions, ...) The change in struct size doesn't change other structure sizes (it is already maxed out to 256 bytes, for example here: union { struct atto_ioctl_vda_scsi_cmd scsi; struct atto_ioctl_vda_flash_cmd flash; struct atto_ioctl_vda_diag_cmd diag; struct atto_ioctl_vda_cli_cmd cli; struct atto_ioctl_vda_smp_cmd smp; struct atto_ioctl_vda_cfg_cmd cfg; struct atto_ioctl_vda_mgt_cmd mgt; struct atto_ioctl_vda_gsv_cmd gsv; u8 cmd_info[256]; } cmd; No sizes are calculated using the enclosing structure, so no other updates are needed. Link: https://lore.kernel.org/r/20210528181337.792268-3-keescook@chromium.orgReviewed-by: -
Randy Dunlap authored
The BusLogic driver has build errors on ia64 due to a name collision (in the #included FlashPoint.c file). Rename the struct field in struct sccb_mgr_info from si_flags to si_mflags (manager flags) to mend the build. This is the first problem. There are 50+ others after this one: In file included from ../include/uapi/linux/signal.h:6, from ../include/linux/signal_types.h:10, from ../include/linux/sched.h:29, from ../include/linux/hardirq.h:9, from ../include/linux/interrupt.h:11, from ../drivers/scsi/BusLogic.c:27: ../arch/ia64/include/uapi/asm/siginfo.h:15:27: error: expected ':', ',', ';', '}' or '__attribute__' before '.' token 15 | #define si_flags _sifields._sigfault._flags | ^ ../drivers/scsi/FlashPoint.c:43:6: note: in expansion of macro 'si_flags' 43 | u16 si_flags; | ^~~~~~~~ In file included from ../drivers/scsi/BusLogic.c:51: ../drivers/scsi/FlashPoint.c: In function 'FlashPoint_ProbeHostAdapter': ../drivers/scsi/FlashPoint.c:1076:11: error: 'struct sccb_mgr_info' has no member named '_sifields' 1076 | pCardInfo->si_flags = 0x0000; | ^~ ../drivers/scsi/FlashPoint.c:1079:12: error: 'struct sccb_mgr_info' has no member named '_sifields' Link: https://lore.kernel.org/r/20210529234857.6870-1-rdunlap@infradead.org Fixes: 391e2f25 ("[SCSI] BusLogic: Port driver to 64-bit.") Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Hannes Reinecke <hare@suse.de> Cc: Khalid Aziz <khalid.aziz@oracle.com> Cc: Khalid Aziz <khalid@gonehiking.org> Reported-by:Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enable -Wimplicit-fallthrough for Clang, fix a couple of warnings by explicitly adding break statements instead of just letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115 Link: https://lore.kernel.org/r/20210528200828.GA39349@embeddedorReviewed-by:
-
