- 05 Oct, 2019 40 commits
-
-
Ulf Hansson authored
[ Upstream commit bd880b00 ] To avoid each host driver supporting SDIO IRQs, from keeping track internally about if SDIO IRQs has been claimed, let's introduce a common helper function, sdio_irq_claimed(). The function returns true if SDIO IRQs are claimed, via using the information about the number of claimed irqs. This is safe, even without any locks, as long as the helper function is called only from runtime/system suspend callbacks of the host driver. Tested-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Al Cooper authored
[ Upstream commit c894e33d ] When switching from any MMC speed mode that requires 1.8v (HS200, HS400 and HS400ES) to High Speed (HS) mode, the system ends up configured for SDR12 with a 50MHz clock which is an illegal mode. This happens because the SDHCI_CTRL_VDD_180 bit in the SDHCI_HOST_CONTROL2 register is left set and when this bit is set, the speed mode is controlled by the SDHCI_CTRL_UHS field in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling() because there is no UHS mode being set. The fix is to change sdhci_set_uhs_signaling() to set the SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for any switch to HS mode. This was found on a new eMMC controller that does strict checking of the speed mode and the corresponding clock rate. It caused the switch to HS400 mode to fail because part of the sequence to switch to HS400 requires a switch from HS200 to HS before going to HS400. Suggested-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Al Cooper <alcooperx@gmail.com> Signed-off-by:
-
Ulf Hansson authored
[ Upstream commit 36d57efb ] The sdio_irq_pending flag is used to let host drivers indicate that it has signaled an IRQ. If that is the case and we only have a single SDIO func that have claimed an SDIO IRQ, our assumption is that we can avoid reading the SDIO_CCCR_INTx register and just call the SDIO func irq handler immediately. This makes sense, but the flag is set/cleared in a somewhat messy order, let's fix that up according to below. First, the flag is currently set in sdio_run_irqs(), which is executed as a work that was scheduled from sdio_signal_irq(). To make it more implicit that the host have signaled an IRQ, let's instead immediately set the flag in sdio_signal_irq(). This also makes the behavior consistent with host drivers that uses the legacy, mmc_signal_sdio_irq() API. This have no functional impact, because we don't expect host drivers to call sdio_signal_irq() until after the work (sdio_run_irqs()) have been executed anyways. Second, currently we never clears the flag when using the sdio_run_irqs() work, but only when using the sdio_irq_thread(). Let make the behavior consistent, by moving the flag to be cleared inside the common process_sdio_pending_irqs() function. Additionally, tweak the behavior of the flag slightly, by avoiding to clear it unless we processed the SDIO IRQ. The purpose with this at this point, is to keep the information about whether there have been an SDIO IRQ signaled by the host, so at system resume we can decide to process it without reading the SDIO_CCCR_INTx register. Tested-by:
-
Guoqing Jiang authored
[ Upstream commit 6ce220dd ] If stripe in batch list is set with STRIPE_HANDLE flag, then the stripe could be set with STRIPE_ACTIVE by the handle_stripe function. And if error happens to the batch_head at the same time, break_stripe_batch_list is called, then below warning could happen (the same report in [1]), it means a member of batch list was set with STRIPE_ACTIVE. [7028915.431770] stripe state: 2001 [7028915.431815] ------------[ cut here ]------------ [7028915.431828] WARNING: CPU: 18 PID: 29089 at drivers/md/raid5.c:4614 break_stripe_batch_list+0x203/0x240 [raid456] [...] [7028915.431879] CPU: 18 PID: 29089 Comm: kworker/u82:5 Tainted: G O 4.14.86-1-storage #4.14.86-1.2~deb9 [7028915.431881] Hardware name: Supermicro SSG-2028R-ACR24L/X10DRH-iT, BIOS 3.1 06/18/2018 [7028915.431888] Workqueue: raid5wq raid5_do_work [raid456] [7028915.431890] task: ffff9ab0ef36d7c0 task.stack: ffffb72926f84000 [7028915.431896] RIP: 0010:break_stripe_batch_list+0x203/0x240 [raid456] [7028915.431898] RSP: 0018:ffffb72926f87ba8 EFLAGS: 00010286 [7028915.431900] RAX: 0000000000000012 RBX: ffff9aaa84a98000 RCX: 0000000000000000 [7028915.431901] RDX: 0000000000000000 RSI: ffff9ab2bfa15458 RDI: ffff9ab2bfa15458 [7028915.431902] RBP: ffff9aaa8fb4e900 R08: 0000000000000001 R09: 0000000000002eb4 [7028915.431903] R10: 00000000ffffffff R11: 0000000000000000 R12: ffff9ab1736f1b00 [7028915.431904] R13: 0000000000000000 R14: ffff9aaa8fb4e900 R15: 0000000000000001 [7028915.431906] FS: 0000000000000000(0000) GS:ffff9ab2bfa00000(0000) knlGS:0000000000000000 [7028915.431907] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [7028915.431908] CR2: 00007ff953b9f5d8 CR3: 0000000bf4009002 CR4: 00000000003606e0 [7028915.431909] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [7028915.431910] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [7028915.431910] Call Trace: [7028915.431923] handle_stripe+0x8e7/0x2020 [raid456] [7028915.431930] ? __wake_up_common_lock+0x89/0xc0 [7028915.431935] handle_active_stripes.isra.58+0x35f/0x560 [raid456] [7028915.431939] raid5_do_work+0xc6/0x1f0 [raid456] Also commit 59fc630b ("RAID5: batch adjacent full stripe write") said "If a stripe is added to batch list, then only the first stripe of the list should be put to handle_list and run handle_stripe." So don't set STRIPE_HANDLE to stripe which is already in batch list, otherwise the stripe could be put to handle_list and run handle_stripe, then the above warning could be triggered. [1]. https://www.spinics.net/lists/raid/msg62552.htmlSigned-off-by:
Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit 2ec42f31 ] Some tools use the snd_pcm_info_get_name() to try to identify PCMs or for other purposes. Currently it is left empty with the dmaengine-pcm, in this case copy the pcm->id string as pcm->name. For example IGT is using this to find the HDMI PCM for testing audio on it. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Reported-by:
Arthur She <arthur.she@linaro.org> Link: https://lore.kernel.org/r/20190906055524.7393-1-peter.ujfalusi@ti.comSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
M. Vefa Bicakci authored
[ Upstream commit 7d505758 ] On a Xen-based PVH virtual machine with more than 4 GiB of RAM, intel_pmc_core fails initialization with the following warning message from the kernel, indicating that the driver is attempting to ioremap RAM: ioremap on RAM at 0x00000000fe000000 - 0x00000000fe001fff WARNING: CPU: 1 PID: 434 at arch/x86/mm/ioremap.c:186 __ioremap_caller.constprop.0+0x2aa/0x2c0 ... Call Trace: ? pmc_core_probe+0x87/0x2d0 [intel_pmc_core] pmc_core_probe+0x87/0x2d0 [intel_pmc_core] This issue appears to manifest itself because of the following fallback mechanism in the driver: if (lpit_read_residency_count_address(&slp_s0_addr)) pmcdev->base_addr = PMC_BASE_ADDR_DEFAULT; The validity of address PMC_BASE_ADDR_DEFAULT (i.e., 0xFE000000) is not verified by the driver, which is what this patch introduces. With this patch, if address PMC_BASE_ADDR_DEFAULT is in RAM, then the driver will not attempt to ioremap the aforementioned address. Signed-off-by:
M. Vefa Bicakci <m.v.b@runbox.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Gayatri Kammela authored
[ Upstream commit 6e1c32c5 ] Add the model numbers/CPUIDs of Tiger Lake mobile and desktop to the Intel family. Suggested-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
Gayatri Kammela <gayatri.kammela@intel.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Harald Freudenberger authored
[ Upstream commit 9e323d45 ] With 'extra run-time crypto self tests' enabled, the selftest for s390-xts fails with alg: skcipher: xts-aes-s390 encryption unexpectedly succeeded on test vector "random: len=0 klen=64"; expected_error=-22, cfg="random: inplace use_digest nosimd src_divs=[2.61%@+4006, 84.44%@+21, 1.55%@+13, 4.50%@+344, 4.26%@+21, 2.64%@+27]" This special case with nbytes=0 is not handled correctly and this fix now makes sure that -EINVAL is returned when there is en/decrypt called with 0 bytes to en/decrypt. Signed-off-by:
Harald Freudenberger <freude@linux.ibm.com> Signed-off-by:
Vasily Gorbik <gor@linux.ibm.com> Signed-off-by:
-
Masami Hiramatsu authored
[ Upstream commit e336b402 ] Since BUG() and WARN() may use a trap (e.g. UD2 on x86) to get the address where the BUG() has occurred, kprobes can not do single-step out-of-line that instruction. So prohibit probing on such address. Without this fix, if someone put a kprobe on WARN(), the kernel will crash with invalid opcode error instead of outputing warning message, because kernel can not find correct bug address. Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N . Rao <naveen.n.rao@linux.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/156750890133.19112.3393666300746167111.stgit@devnote2Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit c5dbe606 ] Skip resetting paRAM slots marked as reserved as they might be used by other cores. Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Yufen Yu authored
[ Upstream commit 07f1a685 ] When run test case: mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] --assume-clean --bitmap=internal mdadm -S /dev/md1 mdadm -A /dev/md1 /dev/sd[b-c] --run --force mdadm --zero /dev/sda mdadm /dev/md1 -a /dev/sda echo offline > /sys/block/sdc/device/state echo offline > /sys/block/sdb/device/state sleep 5 mdadm -S /dev/md1 echo running > /sys/block/sdb/device/state echo running > /sys/block/sdc/device/state mdadm -A /dev/md1 /dev/sd[a-c] --run --force mdadm run fail with kernel message as follow: [ 172.986064] md: kicking non-fresh sdb from array! [ 173.004210] md: kicking non-fresh sdc from array! [ 173.022383] md/raid1:md1: active with 0 out of 4 mirrors [ 173.022406] md1: failed to create bitmap (-5) In fact, when active disk in raid1 array less than one, we need to return fail in raid1_run(). Reviewed-by:
NeilBrown <neilb@suse.de> Signed-off-by:
Yufen Yu <yuyufen@huawei.com> Signed-off-by:
-
Wang Shenran authored
[ Upstream commit 6e4d91aa ] At boot time, the acpi_power_meter driver logs the following error level message: "Ignoring unsafe software power cap". Having read about it from a few sources, it seems that the error message can be quite misleading. While the message can imply that Linux is ignoring the fact that the system is operating in potentially dangerous conditions, the truth is the driver found an ACPI_PMC object that supports software power capping. The driver simply decides not to use it, perhaps because it doesn't support the object. The best solution is probably changing the log level from error to warning. All sources I have found, regarding the error, have downplayed its significance. There is not much of a reason for it to be on error level, while causing potential confusions or misinterpretations. Signed-off-by:
Wang Shenran <shenran268@gmail.com> Link: https://lore.kernel.org/r/20190724080110.6952-1-shenran268@gmail.comSigned-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Kent Overstreet authored
[ Upstream commit a22a9602 ] The race was when a thread using closure_sync() notices cl->s->done == 1 before the thread calling closure_put() calls wake_up_process(). Then, it's possible for that thread to return and exit just before wake_up_process() is called - so we're trying to wake up a process that no longer exists. rcu_read_lock() is sufficient to protect against this, as there's an rcu barrier somewhere in the process teardown path. Signed-off-by:
Kent Overstreet <kent.overstreet@gmail.com> Acked-by:
Coly Li <colyli@suse.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Wenwen Wang authored
[ Upstream commit 29b49958 ] In acpi_pci_irq_enable(), 'entry' is allocated by kzalloc() in acpi_pci_irq_check_entry() (invoked from acpi_pci_irq_lookup()). However, it is not deallocated if acpi_pci_irq_valid() returns false, leading to a memory leak. To fix this issue, free 'entry' before returning 0. Fixes: e237a551 ("x86/ACPI/PCI: Recognize that Interrupt Line 255 means "not connected"") Signed-off-by:
Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Wenwen Wang authored
[ Upstream commit 03d1571d ] In cm_write(), 'buf' is allocated through kzalloc(). In the following execution, if an error occurs, 'buf' is not deallocated, leading to memory leaks. To fix this issue, free 'buf' before returning the error. Fixes: 526b4af4 ("ACPI: Split out custom_method functionality into an own driver") Signed-off-by:
-
Marek Szyprowski authored
[ Upstream commit 5b0eeeaa ] Commit aff138bf ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit, but it turned out that it supplies also some other critical parts and board freezes/crashes when it is turned off. The mentioned commit made Exynos TMU a consumer of that regulator and in typical case Exynos TMU driver keeps it enabled from early boot. However there are such configurations (example is multi_v7_defconfig), in which some of the regulators are compiled as modules and are not available from early boot. In such case it may happen that LDO10 is turned off by regulator core, because it has no consumers yet (in this case consumer drivers cannot get it, because the supply regulators for it are not yet available). This in turn causes the board to crash. This patch restores 'always-on' property for the LDO10 regulator. Fixes: aff138bf ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards") Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Tzvetomir Stoyanov authored
[ Upstream commit e97fd138 ] To be compliant with XDG user directory layout, the user's plugin directory is changed from ~/.traceevent/plugins to ~/.local/lib/traceevent/plugins/ Suggested-by:
Patrick McLean <chutzpah@gentoo.org> Signed-off-by:
Tzvetomir Stoyanov <tstoyanov@vmware.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Patrick McLean <chutzpah@gentoo.org> Cc: linux-trace-devel@vger.kernel.org Link: https://lore.kernel.org/linux-trace-devel/20190313144206.41e75cf8@patrickm/ Link: http://lore.kernel.org/linux-trace-devel/20190801074959.22023-4-tz.stoyanov@gmail.com Link: http://lore.kernel.org/lkml/20190805204355.344622683@goodmis.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 0d87308c ] In commit 14bd9a60 ("iommu/iova: Separate atomic variables to improve performance") Jinyu Qi identified that the atomic_cmpxchg() in queue_iova() was causing a performance loss and moved critical fields so that the false sharing would not impact them. However, avoiding the false sharing in the first place seems easy. We should attempt the atomic_cmpxchg() no more than 100 times per second. Adding an atomic_read() will keep the cache line mostly shared. This false sharing came with commit 9a005a80 ("iommu/iova: Add flush timer"). Signed-off-by:
Eric Dumazet <edumazet@google.com> Fixes: 9a005a80 ('iommu/iova: Add flush timer') Cc: Jinyu Qi <jinyuqi@huawei.com> Cc: Joerg Roedel <jroedel@suse.de> Acked-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Dan Williams authored
[ Upstream commit c312ef17 ] The Linux ahci driver has historically implemented a configuration fixup for platforms / platform-firmware that fails to enable the ports prior to OS hand-off at boot. The fixup was originally implemented way back before ahci moved from drivers/scsi/ to drivers/ata/, and was updated in 2007 via commit 49f29090 "ahci: update PCS programming". The quirk sets a port-enable bitmap in the PCS register at offset 0x92. This quirk could be applied generically up until the arrival of the Denverton (DNV) platform. The DNV AHCI controller architecture supports more than 6 ports and along with that the PCS register location and format were updated to allow for more possible ports in the bitmap. DNV AHCI expands the register to 32-bits and moves it to offset 0x94. As it stands there are no known problem reports with existing Linux trying to set bits at offset 0x92 which indicates that the quirk is not applicable. Likely it is not applicable on a wider range of platforms, but it is difficult to discern which platforms if any still depend on the quirk. Rather than try to fix the PCS quirk to consider the DNV register layout instead require explicit opt-in. The assumption is that the OS driver need not touch this register, and platforms can be added with a new boad_ahci_pcs7 board-id when / if problematic platforms are found in the future. The logic in ahci_intel_pcs_quirk() looks for all Intel AHCI instances with "legacy" board-ids and otherwise skips the quirk if the board was matched by class-code. Reported-by:
Stephen Douthit <stephend@silicom-usa.com> Cc: Christoph Hellwig <hch@infradead.org> Reviewed-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Qian Cai authored
[ Upstream commit 3d708895 ] When running heavy memory pressure workloads, the system is throwing endless warnings, smartpqi 0000:23:00.0: AMD-Vi: IOMMU mapping error in map_sg (io-pages: 5 reason: -12) Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40 07/10/2019 swapper/10: page allocation failure: order:0, mode:0xa20(GFP_ATOMIC), nodemask=(null),cpuset=/,mems_allowed=0,4 Call Trace: <IRQ> dump_stack+0x62/0x9a warn_alloc.cold.43+0x8a/0x148 __alloc_pages_nodemask+0x1a5c/0x1bb0 get_zeroed_page+0x16/0x20 iommu_map_page+0x477/0x540 map_sg+0x1ce/0x2f0 scsi_dma_map+0xc6/0x160 pqi_raid_submit_scsi_cmd_with_io_request+0x1c3/0x470 [smartpqi] do_IRQ+0x81/0x170 common_interrupt+0xf/0xf </IRQ> because the allocation could fail from iommu_map_page(), and the volume of this call could be huge which may generate a lot of serial console output and cosumes all CPUs. Fix it by silencing the warning in this call site, and there is still a dev_err() later to notify the failure. Signed-off-by:
Qian Cai <cai@lca.pw> Signed-off-by:
-
Takashi Sakamoto authored
[ Upstream commit 6af86bdb ] MOTU 4pre was launched in 2012 by MOTU, Inc. This commit allows userspace applications can transmit and receive PCM frames and MIDI messages for this model via ALSA PCM interface and RawMidi/Sequencer interfaces. The device supports MOTU protocol version 3. Unlike the other devices, the device is simply designed. The size of data block is fixed to 10 quadlets during available sampling rates (44.1 - 96.0 kHz). Each data block includes 1 source packet header, 2 data chunks for messages, 8 data chunks for PCM samples and 2 data chunks for padding to quadlet alignment. The device has no MIDI, optical, BNC and AES/EBU interfaces. Like support for the other MOTU devices, the quality of playback sound is not enough good with periodical noise yet. $ python2 crpp < ~/git/am-config-rom/motu/motu-4pre.img ROM header and bus information block ----------------------------------------------------------------- 400 041078cc bus_info_length 4, crc_length 16, crc 30924 404 31333934 bus_name "1394" 408 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256) 40c 0001f200 company_id 0001f2 | 410 000a41c5 device_id 00000a41c5 | EUI-64 0001f200000a41c5 root directory ----------------------------------------------------------------- 414 0004ef04 directory_length 4, crc 61188 418 030001f2 vendor 41c 0c0083c0 node capabilities per IEEE 1394 420 d1000002 --> unit directory at 428 424 8d000005 --> eui-64 leaf at 438 unit directory at 428 ----------------------------------------------------------------- 428 0003ceda directory_length 3, crc 52954 42c 120001f2 specifier id 430 13000045 version 434 17103800 model eui-64 leaf at 438 ----------------------------------------------------------------- 438 0002d248 leaf_length 2, crc 53832 43c 0001f200 company_id 0001f2 | 440 000a41c5 device_id 00000a41c5 | EUI-64 0001f200000a41c5 Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Anton Eidelman authored
[ Upstream commit e01f91df ] ANA log parsing invokes nvme_update_ana_state() per ANA group desc. This updates the state of namespaces with nsids in desc->nsids[]. Both ctrl->namespaces list and desc->nsids[] array are sorted by nsid. Hence nvme_update_ana_state() performs a single walk over ctrl->namespaces: - if current namespace matches the current desc->nsids[n], this namespace is updated, and n is incremented. - the process stops when it encounters the end of either ctrl->namespaces end or desc->nsids[] In case desc->nsids[n] does not match any of ctrl->namespaces, the remaining nsids following desc->nsids[n] will not be updated. Such situation was considered abnormal and generated WARN_ON_ONCE. However ANA log MAY contain nsids not (yet) found in ctrl->namespaces. For example, lets consider the following scenario: - nvme0 exposes namespaces with nsids = [2, 3] to the host - a new namespace nsid = 1 is added dynamically - also, a ANA topology change is triggered - NS_CHANGED aen is generated and triggers scan_work - before scan_work discovers nsid=1 and creates a namespace, a NOTICE_ANA aen was issues and ana_work receives ANA log with nsids=[1, 2, 3] Result: ana_work fails to update ANA state on existing namespaces [2, 3] Solution: Change the way nvme_update_ana_state() namespace list walk checks the current namespace against desc->nsids[n] as follows: a) ns->head->ns_id < desc->nsids[n]: keep walking ctrl->namespaces. b) ns->head->ns_id == desc->nsids[n]: match, update the namespace c) ns->head->ns_id >= desc->nsids[n]: skip to desc->nsids[n+1] This enables correct operation in the scenario described above. This also allows ANA log to contain nsids currently invisible to the host, i.e. inactive nsids. Signed-off-by:
Anton Eidelman <anton@lightbitslabs.com> Reviewed-by:
James Smart <james.smart@broadcom.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
-
Tom Wu authored
[ Upstream commit 3bec2e37 ] In nvme spec 1.3 there is a definition for data write/read counters from SMART log, (See section 5.14.1.2): This value is reported in thousands (i.e., a value of 1 corresponds to 1000 units of 512 bytes read) and is rounded up. However, in nvme target where value is reported with actual units, but not thousands of units as the spec requires. Signed-off-by:
Tom Wu <tomwu@mellanox.com> Reviewed-by:
Israel Rukshin <israelr@mellanox.com> Reviewed-by:
Max Gurtovoy <maxg@mellanox.com> Reviewed-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by:
-
Song Liu authored
[ Upstream commit 825d0b73 ] pti_clone_pmds() assumes that the supplied address is either: - properly PUD/PMD aligned or - the address is actually mapped which means that independently of the mapping level (PUD/PMD/PTE) the next higher mapping exists. If that's not the case the unaligned address can be incremented by PUD or PMD size incorrectly. All callers supply mapped and/or aligned addresses, but for the sake of robustness it's better to handle that case properly and to emit a warning. [ tglx: Rewrote changelog and added WARN_ON_ONCE() ] Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908282352470.1938@nanos.tec.linutronix.deSigned-off-by:
-
Shengjiu Wang authored
[ Upstream commit 696d0522 ] The test case is arecord -Dhw:0 -d 10 -f S16_LE -r 48000 -c 2 temp.wav & aplay -Dhw:0 -d 30 -f S16_LE -r 48000 -c 2 test.wav There will be error after end of arecord: aplay: pcm_write:2051: write error: Input/output error Capture and Playback work in parallel in master mode, one substream stops, the other substream is impacted, the reason is that clock is disabled wrongly. The clock's reference count is not increased when second substream starts, the hw_param() function returns in the beginning because first substream is enabled, then in end of first substream, the hw_free() disables the clock. This patch is to move the clock enablement to the place before checking of the device enablement in hw_param(). Signed-off-by:
Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://lore.kernel.org/r/1567012817-12625-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by:
-
Thomas Gleixner authored
[ Upstream commit 990784b5 ] When PTI is disabled at boot time either because the CPU is not affected or PTI has been disabled on the command line, the boot code still calls into pti_finalize() which then unconditionally invokes: pti_clone_entry_text() pti_clone_kernel_text() pti_clone_kernel_text() was called unconditionally before the 32bit support was added and 32bit added the call to pti_clone_entry_text(). The call has no side effects as cloning the page tables into the available second one, which was allocated for PTI does not create damage. But it does not make sense either and in case that this functionality would be extended later this might actually lead to hard to diagnose issues. Neither function should be called when PTI is runtime disabled. Make the invocation conditional. Signed-off-by:
Dave Hansen <dave.hansen@linux.intel.com> Acked-by:
-
Mark Rutland authored
[ Upstream commit f32c7a8e ] While the MMUs is disabled, I-cache speculation can result in instructions being fetched from the PoC. During boot we may patch instructions (e.g. for alternatives and jump labels), and these may be dirty at the PoU (and stale at the PoC). Thus, while the MMU is disabled in the KPTI pagetable fixup code we may load stale instructions into the I-cache, potentially leading to subsequent crashes when executing regions of code which have been modified at runtime. Similarly to commit: 8ec41987 ("arm64: mm: ensure patched kernel text is fetched from PoU") ... we can invalidate the I-cache after enabling the MMU to prevent such issues. The KPTI pagetable fixup code itself should be clean to the PoC per the boot protocol, so no maintenance is required for this code. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by:
James Morse <james.morse@arm.com> Signed-off-by:
Will Deacon <will@kernel.org> Signed-off-by:
-
Neil Horman authored
[ Upstream commit 743dac49 ] On x86, CPUs are limited in the number of interrupts they can have affined to them as they only support 256 interrupt vectors per CPU. 32 vectors are reserved for the CPU and the kernel reserves another 22 for internal purposes. That leaves 202 vectors for assignement to devices. When an interrupt is set up or the affinity is changed by the kernel or the administrator, the vector assignment code attempts to honor the requested affinity mask. If the vector space on the CPUs in that affinity mask is exhausted the code falls back to a wider set of CPUs and assigns a vector on a CPU outside of the requested affinity mask silently. While the effective affinity is reflected in the corresponding /proc/irq/$N/effective_affinity* files the silent breakage of the requested affinity can lead to unexpected behaviour for administrators. Add a pr_warn() when this happens so that adminstrators get at least informed about it in the syslog. [ tglx: Massaged changelog and made the pr_warn() more informative ] Reported-by: djuran@redhat.com Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Douglas RAILLARD authored
[ Upstream commit 77c84dd1 ] Fast switching path only emits an event for the CPU of interest, whereas the regular path emits an event for all the CPUs that had their frequency changed, i.e. all the CPUs sharing the same policy. With the current behavior, looking at cpu_frequency event for a given CPU that is using the fast switching path will not give the correct frequency signal. Signed-off-by:
Douglas RAILLARD <douglas.raillard@arm.com> Acked-by:
-
Al Stone authored
[ Upstream commit 4c4cdc4c ] According to the ACPI 6.3 specification, the _PSD method is optional when using CPPC. The underlying assumption is that each CPU can change frequency independently from all other CPUs; _PSD is provided to tell the OS that some processors can NOT do that. However, the acpi_get_psd() function returns ENODEV if there is no _PSD method present, or an ACPI error status if an error occurs when evaluating _PSD, if present. This makes _PSD mandatory when using CPPC, in violation of the specification, and only on Linux. This has forced some firmware writers to provide a dummy _PSD, even though it is irrelevant, but only because Linux requires it; other OSPMs follow the spec. We really do not want to have OS specific ACPI tables, though. So, correct acpi_get_psd() so that it does not return an error if there is no _PSD method present, but does return a failure when the method can not be executed properly. This allows _PSD to be optional as it should be. Signed-off-by:
Al Stone <ahs3@redhat.com> Signed-off-by:
-
Katsuhiro Suzuki authored
[ Upstream commit f972d02f ] This patch fix setting table of Headphone mixer volume. Current code uses 4 ... 7 values but these values are prohibited. Correct settings are the following: 0000 -12dB 0001 -10.5dB 0010 -9dB 0011 -7.5dB 0100 -6dB 1000 -4.5dB 1001 -3dB 1010 -1.5dB 1011 0dB Signed-off-by:
Katsuhiro Suzuki <katsuhiro@katsuster.net> Reviewed-by:
Daniel Drake <drake@endlessm.com> Link: https://lore.kernel.org/r/20190826153900.25969-1-katsuhiro@katsuster.netSigned-off-by:
-
Mauro Carvalho Chehab authored
[ Upstream commit 093347ab ] As pointed by cppcheck: [drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour [drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour [drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour Prevent mangling with gains with invalid values. As pointed by Sylvester, this should never happen in practice, as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16 and m is always >= 0), but it is too hard for a static analyzer to get this, as the logic with validates control min/max is elsewhere inside V4L2 core. Reviewed-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Benjamin Peterson authored
[ Upstream commit b92675f4 ] While tracing a program that calls isatty(3), I noticed that strace reported TCGETS for the request argument of the underlying ioctl(2) syscall while perf trace reported TCSETS. strace is corrrect. The bug in perf was due to the tty ioctl beauty table starting at 0x5400 rather than 0x5401. Committer testing: Using augmented_raw_syscalls.o and settings to make 'perf trace' use strace formatting, i.e. with this in ~/.perfconfig # cat ~/.perfconfig [trace] add_events = /home/acme/git/linux/tools/perf/examples/bpf/augmented_raw_syscalls.c show_zeros = yes show_duration = no no_inherit = yes show_timestamp = no show_arg_names = no args_alignment = 40 show_prefix = yes # strace -e ioctl stty > /dev/null ioctl(0, TCGETS, {B38400 opost isig icanon echo ...}) = 0 ioctl(1, TIOCGWINSZ, 0x7fff8a9b0860) = -1 ENOTTY (Inappropriate ioctl for device) ioctl(1, TCGETS, 0x7fff8a9b0540) = -1 ENOTTY (Inappropriate ioctl for device) +++ exited with 0 +++ # Before: # perf trace -e ioctl stty > /dev/null ioctl(0, TCSETS, 0x7fff2cf79f20) = 0 ioctl(1, TIOCSWINSZ, 0x7fff2cf79f40) = -1 ENOTTY (Inappropriate ioctl for device) ioctl(1, TCSETS, 0x7fff2cf79c20) = -1 ENOTTY (Inappropriate ioctl for device) # After: # perf trace -e ioctl stty > /dev/null ioctl(0, TCGETS, 0x7ffed0763920) = 0 ioctl(1, TIOCGWINSZ, 0x7ffed0763940) = -1 ENOTTY (Inappropriate ioctl for device) ioctl(1, TCGETS, 0x7ffed0763620) = -1 ENOTTY (Inappropriate ioctl for device) # Signed-off-by:
Benjamin Peterson <benjamin@python.org> Tested-by:
-
Maciej S. Szmigiero authored
[ Upstream commit 9d802222 ] saa7134_i2c_eeprom_md7134_gate() function and the associated comment uses an inverted i2c gate open / closed terminology. Let's fix this. Signed-off-by:
Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> [hverkuil-cisco@xs4all.nl: fix alignment checkpatch warning] Signed-off-by:
-
Wenwen Wang authored
[ Upstream commit 1c770f0f ] In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array(). However, it is not deallocated if the following allocation for urbs fails. To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails. Signed-off-by:
-
Wenwen Wang authored
[ Upstream commit 42e64117 ] If saa7146_register_device() fails, no cleanup is executed, leading to memory/resource leaks. To fix this issue, perform necessary cleanup work before returning the error. Signed-off-by:
-
Hans Verkuil authored
[ Upstream commit 14d55116 ] If cec_notifier_cec_adap_unregister() is called before cec_unregister_adapter() then everything is OK (and this is the case today). But if it is the other way around, then cec_notifier_unregister() is called first, and that doesn't set n->cec_adap to NULL. So if e.g. cec_notifier_set_phys_addr() is called after cec_notifier_unregister() but before cec_unregister_adapter() then n->cec_adap points to an unregistered and likely deleted cec adapter. So just set n->cec_adap->notifier and n->cec_adap to NULL for rubustness. Eventually cec_notifier_unregister will disappear and this will be simplified substantially. Signed-off-by:
-
Kamil Konieczny authored
[ Upstream commit 2c2b20e0 ] Regulators should be enabled before clocks to avoid h/w hang. This require change in exynos_bus_probe() to move exynos_bus_parse_of() after exynos_bus_parent_parse_of() and change in error handling. Similar change is needed in exynos_bus_exit() where clock should be disabled before regulators. Signed-off-by:
Kamil Konieczny <k.konieczny@partner.samsung.com> Acked-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by:
-
Leonard Crestez authored
[ Upstream commit 0ef7c7cc ] The devfreq passive governor registers and unregisters devfreq transition notifiers on DEVFREQ_GOV_START/GOV_STOP using devm wrappers. If devfreq itself is registered with devm then a warning is triggered on rmmod from devm_devfreq_unregister_notifier. Call stack looks like this: devm_devfreq_unregister_notifier+0x30/0x40 devfreq_passive_event_handler+0x4c/0x88 devfreq_remove_device.part.8+0x6c/0x9c devm_devfreq_dev_release+0x18/0x20 release_nodes+0x1b0/0x220 devres_release_all+0x78/0x84 device_release_driver_internal+0x100/0x1c0 driver_detach+0x4c/0x90 bus_remove_driver+0x7c/0xd0 driver_unregister+0x2c/0x58 platform_driver_unregister+0x10/0x18 imx_devfreq_platdrv_exit+0x14/0xd40 [imx_devfreq] This happens because devres_release_all will first remove all the nodes into a separate todo list so the nested devres_release from devm_devfreq_unregister_notifier won't find anything. Fix the warning by calling the non-devm APIS for frequency notification. Using devm wrappers is not actually useful for a governor anyway: it relies on the devfreq core to correctly match the GOV_START/GOV_STOP notifications. Fixes: 99613311 ("PM / devfreq: Add new passive governor") Signed-off-by:
Leonard Crestez <leonard.crestez@nxp.com> Acked-by:
-
Yazen Ghannam authored
[ Upstream commit 8a2eaab7 ] AMD Family 17h systems currently require address translation in order to report the system address of a DRAM ECC error. This is currently done before decoding the syndrome information. The syndrome information does not depend on the address translation, so the proper EDAC csrow/channel reporting can function without the address. However, the syndrome information will not be decoded if the address translation fails. Decode the syndrome information before doing the address translation. The syndrome information is architecturally defined in MCA_SYND and can be considered robust. The address translation is system-specific and may fail on newer systems without proper updates to the translation algorithm. Fixes: 713ad546 ("EDAC, amd64: Define and register UMC error decode function") Signed-off-by:
Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org> Cc: James Morse <james.morse@arm.com> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Tony Luck <tony.luck@intel.com> Link: https://lkml.kernel.org/r/20190821235938.118710-6-Yazen.Ghannam@amd.comSigned-off-by:
-
