The return code FAST_IO_FAIL from fc_block_scsi_eh indicates that the
pending I/O requests have been terminated as a result of the
fast_io_fail_tmo. Pass this return code back to the scsi eh to stop
the scsi eh in this case.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

If the scsi eh is running and then a FC LLD calls
fc_remote_port_delete, the SCSI commands sent from the eh will fail.
To prevent this, a FC LLD can call fc_block_scsi_eh from the eh
callback, blocking the eh thread until the dev_loss_tmo fires or the
remote port is available again.

If (e.g. for a multipathing setup) the dev_loss_tmo is set to a very
large value, thus preventing the scsi device removal , the scsi eh can
block for a long time. For multipathing, the fast_io_fail_tmo is then
set to a low value to detect path problems sooner.

This patch introduces a new return code FAST_IO_FAIL. The function
fc_block_scsi_eh now returns FAST_IO_FAIL when the fast_io_fail_tmo
fires. This indicates that the LLD terminated all pending I/O requests
and there are no more pending SCSI commands for the scsi eh to wait
for. This return code can be passed back to the scsi eh to stop the
escalation and finish the recovery process for this device.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

The default is enabled since 7e47e5ca.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

The qla84xx_mgmt_cmd function supports multiple subcommands.
Some subcommands require DMA memory and some do not.
Therefore check before freeing DMA memory whether it is allocated or not.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Allows priority setting for FCP_CMNDs.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

1. Segregate BSG interface specific code to new files.
2. Handle multiple vendor specific commands indepedently.
3. Reorganised support for reset, management and update FCoE firmware commands.
4. Fixed memory leak issue in Loopback.
5. Added new vendor command to support iiDMA using BSG interface.
6. Proper cleanup of dma mapped and dma allocated buffers for BSG request.

[jejb: fix up conflict and merge in Jiri Slaby lock imbalance patch]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

sg address in IO request is not set up correctly for big endian platform.
add new macros to properly swap the address.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

idr is a global resource, protect it with global bfad_mutex.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Use pci_iomap() and pci_iounmap() to simplify the code. Remove uncessary #ifdef
check for ia64 (it was added as a workaound for some RHEL 5.x release which
doesn't export iounmap function)
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Currently the driver doesn't take into consideraion of possible sg chaining
when it walks through the sg list. This is fixed by using the sg_next()
which automatically handles the chaining case. Obosolete code is removed
as a result of this change.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Use duplicate fc transport template for physical and vitual port. Add
vport create/delete/disalbe functions in the transport template of physical
port. Changes to make the vport create/delete function to work under this
framework.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

This patch (as1359) fixes a bug in scsi_alloc_target().  After a
device structure has been initialized (and especially after its name
has been set), it must not be freed directly.  One has to call
put_device() instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

This patch (as1358) fixes a bug in the error pathway of
scsi_target_add().  If registration fails, the target should not be
reaped.  The reaping occurs later, when scanning is finished and all
the child devices are removed.  The current code leaves an unbalanced
value in starget->reap_ref.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Upgrade version from 3.04.14 to 3.04.15
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Added proper error handling after mpt_config.
Now check of MPI_IOCSTATUS_CONFIG_INVALID_PAGE is added.
If error is MPI_IOCSTATUS_CONFIG_INVALID_PAGE, driver will return -ENODEV.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

event_data needs to be 4 byte aligned to makes sure there is no unaligned
memory access take place.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

1) Corrected name string as "MPT SAS HOST"
2) Added proper check conditions for MPT_MGMT_STATUS_COMMAND_GOOD.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

1) corrected return value as SUCCESS instead of 0.
2) Added check in mptscsih_abort.
mptfusion do not support task abort for Volumes.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Added sanity checks before accessing vdevice and added vdevice->deleted
setting for mptfc.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Set factor, offset and width while target negotiation.

Added config timeout 60 seconds. It was missing for only
mptspi_read_spi_device_pg0
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Added proper bus_type check before processing event/ reset handler.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Current design of mptsas is as follow.
MPTSAS will do probe() if pci id matches for available card in
system, irrespective of mode of controller. If controller is I/T mode
or I mode, things are fine. If controller is only in T mode, mptsas is
not doing complete process of mptsas_probe(). It will only make
sure IOC structure is created and IOC reference is available for
mptstm driver. Now While removing module we should take care
case of Target mode only mptsas. If we are removing IOC which is
only in Target mode, We should only detach IOC instead of
following rest of the cleanup process which is only required for T
mode controller. Now For T mode controller, only part clean up is
done instead of complete cleanup. mpt_detach will call early in case
of Target mode only controller.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

mpt_config would only attempt a MUR before retrying the command. The
driver will now retry a second time with a hard reset before leaving
the function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Behavior changes only for IOCTLs that time out.  Current behavior of
Bus Reset remains the same for RAID Passthru Timeouts Current behavior
of Diagnostic reset for any other type of IOCTL remains the same

CHANGE: For IOCTL SCSI IOs that timeout, a Target Reset TM is sent,
instead of Bus Reset. All error handing from that point is the same as
what the driver currently does, which is to say that if the Device
Reset TM fails it escalates do diagnostic reset.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Message Unit Reset - instructs the IOC to reset the Reply Post and
Free FIFO's. All the Message Frames on Reply Free FIFO are
discarded. All posted buffers are freed, and event notification is
turned off.  IOC doesnt reply to any outstanding request. This will
transfer IOC to READY state.  Message unit ready is less expensive
operations than Hard Reset.  soft reset will not force Firmware to
reload again, it only do clean up of Message units.

mpt_Soft_Hard_ResetHandler will first try for Soft Reset,if
it fails then go for big hammer reset which is Hard Reset.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Upgraded version string.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Copyright changes for year 2010.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

RAID_SCSI_IO_PASSTHROUGH: Driver needs to be send the default
descriptor for RAID Passthru, currently its sending SCSI_IO descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Added proper return type values in case memory allocation failed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Removed all the mutex's for ioc->tm_cmds.mutex, then created one
single mutex inside the function mpt2sas_scsih_issue_tm. This is the
single function used when sending task management. Also the sanity
checks required for scsi mid layer escalation were moved to inside the
same function because these checks need to be done while the mutex is
held. The ioc->tm_cmds.mutex inside the IOCTL branch is really not
required since there is another mutex in this code called for ctl_cmds
handling this sync.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

1. Fixes for little endian issues.
2. Now Debug info for Discovery event is more readable.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Now Driver will not treat NEEDS_INIT as failure. In addition to this,
the driver will now display message to describe the the access flags
when bits are set, so the end user can better understand failures.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Aded checks for shost_recovery flag for early return from function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

use the get_free_pages API for larger contigious physical memory chunk.
Also, the ioc->chain_depth need to be changed from
a 16bit to 32bit variable because the number of chains will exceed 64k
when the queue depth is large.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

bug fix in the handling of the internal device reset event
The reason code check in scsih_sas_device_status_change_event never
evaluates as true for internal device reset, hence driver never quiesce s IO
when firmware is sending a device reset. The fix is to change the
evaluate to:
if (event_data->ReasonCode !=
    MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET &&
   event_data->ReasonCode !=
    MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET)
        return;
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

incorrect timestamp on 32 bit platforms: The upper 32 bit of
the timestamp was getting truncated when converting seconds to
milliseconds, which was due to the variable being long. To fix the problem,
the variable needs to be u64. Also the microseconds conversion to
milliseconds was incorrect; it should be divide by 1000 instead of divide by
8.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mpt2sas : Do not reset handle before calling _scsih_remove_device in RESCAN task after HBA RESET

Setting handle to zero is not required before _scsih_remove_device.
Driver uses sas_device->handle reference in _scsih_remove_device.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>