The endpoint configuration used to be stored in the device tree,
however the configuration depend on the "version" of the controller
itself.

Then the EP child node are useless and describe as deprecated in the
documentation binding: remove all the nodes from the SoC device tree
file. Remove also the #address-cells and #size-cells properties that
are no longer needed.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

There is no need to describe the end point in the deice tree. These
properties won't be use anymore, so mark them as deprecated to keep
the old device tree documented.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The endpoint configuration used to be stored in the device tree,
however the configuration depend on the "version" of the controller
itself.

This information is already documented by the compatible string. It
then possible to just rely on the compatible string and completely
remove the full ep configuration done in the device tree as it was
already the case for all the other USB device controller.
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

DWC_usb32 v1.00a and later can use SET_EP_PRIME command to reinitiate a
stream. Use the command to handle NoStream rejection instead of ending
and restarting the endpoint.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Overview of stream transfer requirement:
 * A transfer will have a set of TRBs of the same stream ID.
 * A transfer is started with a stream ID in START_TRANSFER command.
 * A new stream will only start when the previous completes.

Overview of stream events:
 * A "prime" from host indicates that its endpoints are active
   (buffers prepared and ready to receive/transmit data). The controller
   automatically initiates stream if it sees this.
 * A "NoStream" rejection event indicates that the host isn't ready.
   Host will put the endpoint back to idle state. Device may need to
   reinitiate the stream to start transfer again.
 * A Stream Found event means host accepted device initiated stream.
   Nothing needs to be done from driver.

To initiate a stream, the driver will issue START_TRANSFER command with
a stream ID. To reinitiate the stream, the driver must issue
END_TRANSFER and restart the transfer with START_TRANSFER command with
the same stream ID.

This implementation handles device-initated streams (e.g. UASP driver).
It also handles some hosts' quirky behavior where they only prime each
endpoint once.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Don't prepare TRBs beyond a transfer. In DWC_usb32, its transfer burst
capability may try to read and use TRBs beyond the active transfer. For
other controllers, they don't process the next transfer TRBs until the
current transfer is completed. Explicitly prevent preparing TRBs ahead
for all controllers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

If a transfer is in-progress, any new request should not kick off
another transfer. The driver needs to wait for the current transfer to
complete before starting off the next transfer. Introduce a new flag
DWC3_EP_WAIT_TRANSFER_COMPLETE for this.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

In DWC3, to prepare TRBs for streams, all the TRBs of a transfer will
use the same stream ID. To start a new stream, the driver needs to wait
for the current transfer to complete or ended (by END_TRANFER command).
As a result, inform the controller of the last TRB of a transfer so that
it knows when a transfer completes and start a new transfer of a new
stream.

Even though the transfer completion handling can be applied for other
non-isoc endpoints, only do it for streams due to its requirement.
It's better to keep the controller's TRB cache full than waiting for
transfer completion and starting a new transfer.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

To switch from one stream to another, this requires the driver to start
a new transfer with a specific stream ID. For a transfer to complete,
the driver needs to indicate the last TRB of a transfer, and it needs to
enable XferComplete event to handle completed TRBs of a transfer. Let's
enable this event only for stream capable endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

To prepare for handling of XferComplete event, let's refactor and split
up dwc3_gadget_endpoint_transfer_in_progress() to handle TRBs completion
for different events. The handling of TRBs completion will be the same,
but the status of XferComplete event is different than XferInProgress.
No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

While handling TRBs completion, if a END_TRANSFER command isn't
completed, don't kick new transfer or issue END_TRANSFER command.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Set the request->is_last to each stream request to indicate that the
request is the last stream request of a transfer. The DWC3 controller
needs to know this info to properly switch streams. The current
implementation of f_tcm uses a single request per transfer, so every
stream request is the last of its stream.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

To take advantage of DWC3 internal TRB prefetch and cache for
performance, inform the controller the last request with stream_id
before switching to a different stream transfer. This allows the
controller to maintain its transfer burst within the stream ID.

Introduce the usb-request is_last field to help inform the DWC3
controller of this.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

DWC_usb32 supports MDWIDTH value larger than 255 and up to 1023. The
field HWPARAMS6[9:8] stores the upper 2-bit values of the DWC_usb32's
MDWIDTH. Check that parameter and properly get the MDWIDTH for
DWC_usb32.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Synopsys introduces a new controller DWC_usb32. It supports dual-lane
and speed up to 20 Gbps, and the DWC3 driver will drive this controller.
Currently the driver uses a single field dwc->revision to ID both
DWC_usb3 and DWC_usb31 and their version number. This was sufficient for
two IPs, but this method doesn't work with additional IPs. As a result,
let's separate the dwc->revision field to 2 separate fields: ip and
revision. The ip field now stores the ID of the controller's IP while
the revision field stores the controller's version number.

This new scheme enforces DWC3 to compare the revision within the same IP
only. As a result, we must update all the revision check of the
controller to check its corresponding IP.

To help with this enforcement, we create a few macros to help with
the common version checks:

DWC3_IP_IS(IP)
DWC3_VER_IS(IP, VERSION)
DWC3_VER_IS_PRIOR(IP, VERSION)
DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION)
DWC3_VER_TYPE_IS_WITHIN(IP, VERSION,
			LOWER_VERSION_TYPE,
			UPPER_VERSION_TYPE)

The DWC_usb32 controller operates using the same programming model and
with very similar configurations as its previous controllers. Please
note that the various IP and revision checks in this patch match the
current checks for DWC_usb31 version 1.90a. Additional configurations
that are unique to DWC_usb32 are applied separately.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

OTG port on Tegra194 supports GEN1 speeds when in device mode and GEN2
speeds when in host mode. dd port_speed_quirk that configures port to
GEN1/GEN2 speds, corresponding to the mode.

Based on work by WayneChang <waynec@nvidia.com>
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

This commit adds support for XUSB device mode controller support on
Tegra194 SoC. This is very similar to the existing Tegra186 XUDC, with lpm
support added in addition.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Extend the Tegra XUSB controller device tree binding with Tegra194
support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Sparse reports a warning at set_link_state()

warning: context imbalance in set_link_state() - unexpected unlock

The root cause is the missing annotation at set_link_state()
Add the missing __must_hold(&dum->lock)
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Sparse reports a warning at xudc_handle_setup()

warning: context imbalance in xudc_handle_setup() - unexpected unlock

The root cause is the missing annotation at xudc_handle_setup()

Add the missing __must_hold(&udc->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

module_usb_composite_driver() makes the code simpler by
eliminating boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Fix the following coccicheck warning:

drivers/usb/gadget/udc/omap_udc.c:2579:2-3: Unneeded semicolon
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Fix the following coccicheck warning:

drivers/usb/gadget/udc/mv_u3d_core.c:1551:5-13: WARNING: Comparison to
bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Fix the following coccicheck warning:

drivers/usb/gadget/udc/net2272.c:57:12-19: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Fix the following coccicheck warning:

drivers/usb/dwc3/drd.c:85:3-24: WARNING: Assignment of 0/1 to bool
variable
drivers/usb/dwc3/drd.c:59:2-23: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The variable status is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Clang warns:

drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of
address of 'ep->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
        if (&ep->queue == NULL)
             ~~~~^~~~~    ~~~~
1 warning generated.

It is not wrong, queue is not a pointer so if ep is not NULL, the
address of queue cannot be NULL. No other driver does a check like this
and this check has been around since the driver was first introduced,
presumably with no issues so it does not seem like this check should be
something else. Just remove it.

Commit afe956c5 ("kbuild: Enable -Wtautological-compare") exposed
this but it is not the root cause of the warning.

Fixes: 3fc154b6 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Link: https://github.com/ClangBuiltLinux/linux/issues/1004Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add suspend resume callbacks to handle the case seen when the bus is
suspended by the HOST, and the device opens the port (cat /dev/ttyGS0).

Gadget controller (like DWC2) doesn't accept usb requests to be queued in
this case (when in L2 state), from the gs_open() call. Error log is printed
- configfs-gadget gadget: acm ttyGS0 can't notify serial state, -11
If the HOST resumes (opens) the bus, the port still isn't functional.

Use suspend/resume callbacks to monitor the gadget suspended state by using
'suspended' flag. In case the port gets opened (cat /dev/ttyGS0), the I/O
stream will be delayed until the bus gets resumed by the HOST.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

When the remote wakeup interrupt is triggered, lx_state is resumed from L2
to L0 state. But when the gadget resume is called, lx_state is still L2.
This prevents the resume callback to queue any request. Any attempt
to queue a request from resume callback will result in:
- "submit request only in active state" debug message to be issued
- dwc2_hsotg_ep_queue() returns -EAGAIN

Call the gadget resume routine after the core is in L0 state.

Fixes: f81f46e1 ("usb: dwc2: implement hibernation during bus suspend/resume")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

This patch changes the function uvc_video_pump to be a separate
scheduled worker. This way the completion handler of each usb request
and every direct caller of the pump has only to schedule the worker
instead of doing the request handling by itself.

Moving the request handling to one thread solves the locking problems
between the three queueing cases in the completion handler, v4l2_qbuf
and video_enable.

Many drivers handle the completion handlers directly in their interrupt
handlers. This patch also reduces the workload on each interrupt.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

This patch corrects the SPDX License Identifier style in
header files related to Renesas USBHS Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Fix the following coccicheck warning:

drivers/usb/gadget/function/f_fs.c:2507:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

There is now an updated bindings for these SoCs making the old
compatible obsolete.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

There is now a dedicated driver for these SoCs making the old compatible
obsolete.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).

Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-g12a-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add the correcly architectured USB Glue node and adapt all the Amlogic
GXL and GXM board to the new organization.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

In order to add support for the Amlogic GXL/GXM USB Glue, this adds
the corresponding :
- PHY names
- clock names
- USB2 PHY init and mode set
- regmap setup
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>