This patch modifies the mdio-octeon driver to work on both ThunderX and
Octeon SoCs from Cavium Inc.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some of the K2E and K2L platforms, the two DWORDs in
efuse occupied by the pre-programmed mac address for
slave port 1 are swapped.  To workaround this issue,
this patch adds a new define NETCP_EFUSE_ADDR_SWAP (2)
which signifies the occurrence of such swapping so that
the driver can take proper action.  The flag can be
enabled in the corresponding netcp interface dts binding
as efuse-mac = <2>  under the corresponding netcp
interface node.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit d999297c
("tipc: reduce locking scope during packet reception") we introduced
a new function tipc_build_bcast_sync_msg(), which carries initial
synchronization data between two nodes at first contact and at
re-contact. In this function, we missed to add synchronization data,
with the effect that the broadcast link endpoints will fail to
synchronize correctly at re-contact between a running and a restarted
node. All other cases work as intended.

With this commit, we fix this bug.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow e8e85cc5 ("packet: remove handling of tx_ring") and remove
the tx_ring parameter from prb_shutdown_retire_blk_timer() as it is only
called with tx_ring = 0.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Holzheu says:

====================
s390/bpf: recache skb->data/hlen for skb_vlan_push/pop

Here the s390 backend for Alexei's patch 4e10df9a ("bpf: introduce
bpf_skb_vlan_push/pop() helpers") plus two bugfixes and two minor
improvements.

The first patch "s390/bpf: clear correct BPF accumulator register" will
also go upstream via Martin's "fixes" branch.

* v2: Integrated suggestions from Joe Perches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow eBPF programs attached to TC qdiscs call skb_vlan_push/pop
via helper functions. These functions may change skb->data/hlen.
This data is cached by s390 JIT to improve performance of ld_abs/ld_ind
instructions. Therefore after a change we have to reload the data.

In case of usage of skb_vlan_push/pop, in the prologue we store
the SKB pointer on the stack and restore it after BPF_JMP_CALL
to skb_vlan_push/pop.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only classic BPF programs that have been converted to eBPF need to clear
the A and X registers. We can check for converted programs with:

  bpf_prog->type == BPF_PROG_TYPE_UNSPEC

So add the check and skip initialization for real eBPF programs.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we have the restriction that jitted BPF programs can
have a maximum size of one page. The reason is that we use short
displacements for the literal pool.

The 20 bit displacements are available since z990 and BPF requires
z196 as minimum. Therefore we can remove this restriction and use
everywhere 20 bit signed long displacements.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The EMIT6_DISP_LH macro passes the "disp" parameter to the _EMIT6_DISP_LH
macro. The _EMIT6_DISP_LH macro uses the "disp" parameter twice:

 unsigned int __disp_h = ((u32)disp) & 0xff000;
 unsigned int __disp_l = ((u32)disp) & 0x00fff;

The EMIT6_DISP_LH is used several times with EMIT_CONST_U64() as "disp"
parameter. Therefore always two constants are created per usage of
EMIT6_DISP_LH.

Fix this and add variable "_disp" to avoid multiple expansions.

* v2: Move "_disp" to _EMIT6_DISP_LH as suggested by Joe Perches

Fixes: 05462310 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we assumed the following BPF to eBPF register mapping:

 - BPF_REG_A -> BPF_REG_7
 - BPF_REG_X -> BPF_REG_8

Unfortunately this mapping is wrong. The correct mapping is:

 - BPF_REG_A -> BPF_REG_0
 - BPF_REG_X -> BPF_REG_7

So clear the correct registers and use the BPF_REG_A and BPF_REG_X
macros instead of BPF_REG_0/7.

Fixes: 05462310 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix mistakenly used, hard coded, port number in get_phv_bit()

Fixes: 77fc29c4 ("net/mlx4_core: Preparations for 802.1ad VLAN support")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joachim Eastwood says:

====================
stmmac clean up for 4.3 part2

This patch set creates proper probe functions in the remaining
dwmac-* drivers, lets the drivers manage their own of match data
structure, and cleans up some of the drivers a bit. Note that
should be no functional change in any of the drivers.

First patch from Fengguang fixes a Coccinelle that was found after
the previous patch set when into next.

Probe functions are best placed just above the platform_driver
struct since it usually needs to call other functions in the
driver but this requires some code movement in the drivers. To
keep the conversion itself easier to review the code movement is
done in separate patches. This creates some extra churn but I
think it's worth it in this case.

As only a couple of drivers actually needs to use of match data
this pushed down from stmmac_platform and into the drivers. This
also makes it possible for drivers to have their own match data
structure. dwmac-rk benefits most from this.

After each driver has it's own probe function and manages it's
own match data the setup/free hooks and common match data struct
are removed.

Sorry for the slightly largish patch set this time around.

Since I can only test the core changes on my platform and not the
specific dwmac-drivers I greatly appreciate if people could test
this on their respective platforms. I did spend quite a bit of
time visually checking all these patches, but nothing beats real
hardware testing. Thanks!

Patch set based on net-next can also be picked up from here:
https://github.com/manabian/linux-lpc.git stmmac_4.3_part2

For those who want to have a look at all the patches for
v4.3 a branch based on Linus master can be found here:
https://github.com/manabian/linux-lpc.git stmmac_4.2

Previous parts can be found here:
http://www.spinics.net/lists/netdev/msg328997.html
http://www.spinics.net/lists/netdev/msg329932.html
http://www.spinics.net/lists/netdev/msg336097.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the two platform specific init callbacks and make
them use a common one by creating a function member in
the internal data structure. This allow us to remove the
layer of indirection and simplify the code a bit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As all dwmac-* drivers have been converted to have a proper probe
function the setup callback can now be removed. Also remove the
free callback that wasn't used by any driver.

New dwmac-* drivers should implement standard probe and remove
functions to preform any needed setup and teardown.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As dwmac-* drivers that need OF match have been converted
to use their own internal OF match data structure this can
now be removed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the setup glue callback and use rk_gmac_ops as OF match
data so it can used directly when calling rk_gmac_setup.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark the rk_gmac_ops structures as static const as they should be.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a new private structure for OF match data in the
dwmac-sti driver. This enables us to eventually drop the
common OF match data structure which contains a lot of
unused fields.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since only a few of the dwmac-* drivers actually need to use
the OF match move handling into the dwmac-* drivers that need
it. This will also allow dwmac-* drivers to use their own
custom match data structure.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As all dwmac-* drivers now have their own probe function move
the common one into dwmac-generic driver and drop the EXPORT.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a new probe functions that call the necessary setup
functions. This is done in preparation for a code refactor
in this driver and dropping the common probe function in
stmmac_platform.c.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and prepares the
driver for further clean ups.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move sun7i_gmac_setup in preparation for turning it into
a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move socfpga_dwmac_probe in preparation for turning it into
a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move ipq806x_gmac_fix_mac_speed in preparation for turning
the setup glue callback in a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:304:1-3: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[je: rebase and insert newline before return]
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lars Persson says:

====================
dwc_eth_qos: Add support for Synopsys DWC Ethernet QoS

This is a driver supporting version 4.10a of the Synopsys DWC Ethernet QoS
gigabit ethernet controller. The IP has changed significantly compared to the
dwmac1000 so a separate driver is justified.

The IP is highly configurable at synthesis time. This driver has been
developed for a subset of the total available feature set. Currently
it supports:
* TSO
* Checksum offload for RX and TX.
* Energy efficient ethernet.
* GMII phy interface.
* The statistics module.
* Single RX and TX queue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add maintainer information for the Synopsys DWC Ethernet QOS driver.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a platform driver for the new generation of the
gigabit ethernet IP from Synopsys. It is developed for version 4.10a
of the IP core.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree binding documentation for the Synopsys DWC Ethernet
QoS driver supporting revision 4.10a of the hardware IP.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
net/mlx4_en: Hardware accelerated 802.1ad

This patchset by Hadar introduces support in Hardware accelerated 802.1ad, for
ConnectX-3pro NIC's.  In order to support existing deployment, and due to some
hardware limitations, the feature is disabled by default, and needed to be
enabled using a private flag in ethtool. Ofcourse user can enable the private
flag only if hardware has support.
After being enabled, the standard ethtool -k/-K can be used.

Patchset was applied and tested over commit 71790a27 ("hv_netvsc: Add structs
and handlers for VF messages")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To enable device support in accelerated 802.1ad vlan, the port
capability "packet has vlan enable" (phv_en) should be set.
Firmware won't work properly, in case phv_en is not set.

The user can enable "phv_en" port capability with the new ethtool
private flag phv-bit. The phv-bit private flag default value is OFF,
users who are interested in 802.1ad hardware acceleration should turn ON
the phv-bit private flag:
$ ethtool --set-priv-flags eth1 phv-bit on

Once the private flag is set, the device is ready for 802.1ad vlan
acceleration.

The user should also change the interface device features and turn on
"tx-vlan-stag-hw-insert" which is off by default:
$ ethtool -K eth1  tx-vlan-stag-hw-insert on

"phv-bit" private flag setting is available only for Physical
Functions(PF), the Virtual Function (VF) will be able to use the feature
by setting "tx-vlan-stag-hw-insert" ethtool device feature only if the
feature was enabled by the Hypervisor.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To add Hardware accelerated support in 802.1ad vlan, replace
Current VLAN macros to CVLAN.
Replace:
MLX4_WQE_CTRL_INS_VLAN
MLX4_CQE_VLAN_PRESENT_MASK
With:
MLX4_WQE_CTRL_INS_CVLAN
MLX4_CQE_CVLAN_PRESENT_MASK
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we support only one ethtool private flag. Prepare
mlx4_en_set_priv_flags function to support more than one private flag.
Will be used in the next patch to support hardware accelerated 802.1ad
vlan.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_core preparation to support hardware accelerated 802.1ad VLAN
device.

To allow 802.1ad accelerated device, "packet has vlan" (phv)
Firmware capability should be available. Firmware without the
phv capability won't behave properly and can't support 802.1ad device
acceleration.

The driver checks the Firmware capability and sets the phv bit
accordingly in SET_PORT command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nicolas Schichan says:

====================
ARM BPF JIT features

This series adds support for more instructions to the ARM BPF JIT
namely skb netdevice type retrieval, skb payload offset retrieval, and
skb packet type retrieval.

This allows 35 tests to use the JIT instead of 29 before.

This series depends on the "BPF JIT fixes for ARM" serie sent earlier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>