Device tree entries for PCIe 2.5G Ethernet NICs
Signed-off-by: John Clark <inindev@gmail.com>
Link: https://lore.kernel.org/r/20230810003156.22123-1-inindev@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add all three PCIe2 IP blocks to the RK3588 DT. Note, that RK3588
also has two PCIe3 IP blocks, that will be handled separately.
Co-developed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@edgeble.ai> # edgeble-neu6a, 6b
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230731165723.53069-6-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The ROCK Pi 4A, ROCK Pi 4B and ROCK Pi 4C boards contain a nor-flash chip
connected to spi1. Enable spi1 and add the device node.

This patch has been tested on ROCK Pi 4A.
Signed-off-by: Stefan Nagy <stefan.nagy@ixypsilon.net>
Link: https://lore.kernel.org/r/20230811201118.15066-1-stefan.nagy@ixypsilon.netSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the NanoPC T6, a single board computer from FriendlyElec based on
the RK3588.

Initial device tree supports debug UART, SD, eMMC, PCIe 3, PMIC,
and 40 pin GPIO assignments.
Signed-off-by: Thomas McKahan <tmckahan@singleboardsolutions.com>
Link: https://lore.kernel.org/r/20230809112120.99-3-tmckahan@singleboardsolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the NanoPC T6, a single board computer from FriendlyElec
Signed-off-by: Thomas McKahan <tmckahan@singleboardsolutions.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230809112120.99-2-tmckahan@singleboardsolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The M.2 KEY B port can be used for WWAN USB2 modules or SATA drives.

Enable sata1 node to fix use of SATA drives on the M.2 slot.

Fixes: 2bf2f4d9 ("arm64: dts: rockchip: Add Radxa CM3I E25")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230724145213.3833099-1-jonas@kwiboo.seSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Despite its name, the regulator vcc3v3_pcie30x1 has nothing to do with
pcie30x1. Instead, it supply power to VBAT1-5 on the M.2 KEY B port as
seen on page 8 of the schematic [1].

pcie30x1 is used for the mini PCIe slot, and as seen on page 9 the
vcc3v3_minipcie regulator is instead related to pcie30x1.

The M.2 KEY B port can be used for WWAN USB2 modules or SATA drives.

Use correct regulator vcc3v3_minipcie for pcie30x1.

[1] https://dl.radxa.com/cm3p/e25/radxa-e25-v1.4-sch.pdf

Fixes: 2bf2f4d9 ("arm64: dts: rockchip: Add Radxa CM3I E25")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230724145213.3833099-1-jonas@kwiboo.seSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The recommended name for enable GPIOs property in regulator-gpio is
enable-gpios.  This is also required by bindings:

  px30-engicam-px30-core-ctouch2.dtb: vcc3v3-btreg: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230725142616.157405-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The recommended name for enable GPIOs property in regulator-gpio is
enable-gpios.  This is also required by bindings:

  rk3399-gru-bob.dtb: ppvar-sd-card-io: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230725142616.157405-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add both PCIe3 controllers together with the shared PHY.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230717173512.65169-3-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

add alias for sdmmc as mmc1.
make card detect work.

Fixes: ea3e66e7 ("arm64: dts: rockchip: add SD card support to rock-5a")
Fixes: 2a6d4af5 ("arm64: dts: rockchip: Add SD card support to rock-5b")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20230722121150.130126-1-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable USB2 (EHCI and OCHI mode) support for the Radxa ROCK 5 Model A.
This adds USB support for the on-board WLAN/BT chip, the two USB2
ports, the USB available from the 2x20 connector and the lower USB3
port (in USB2 mode).

The upper USB3 (further away from the PCB) uses the RK3588S USB TypeC
OTG controller for USB2 and USB3 and thus is not supported at all at
the moment.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-5-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable USB2 (EHCI and OCHI mode) support for the Radxa ROCK 5 Model B.
This adds USB support on the M.2 Key E, both USB2 ports and USB2 mode
for the upper USB3 port (the one further away from the PCB).

The lower USB3 (closer to the PCB) and the USB-C ports use the RK3588
USB TypeC host controller, which is not yet supported upstream.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-4-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable USB2 (EHCI and OCHI mode) support for the Rockchip RK3588 EVB1.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-3-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds USB2 (EHCI & OHCI) ports including the related PHYs
and GRF modules to the rk3588(s) device tree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-2-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add RS485 support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-8-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add RS232 support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-7-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add PWM FAN support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-6-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add RTC support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-5-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add SATA support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-3-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add sdmmc support for Edgeble Neu6B NCM IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-2-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds PMIC support for the Edgeble Neu6B NCM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230713143941.1756849-1-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for the SATA0_0 port found on the RK3588 EVB1. The
second port (SATA0_1) does not work, which matches the downstream
behaviour.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230711171330.52535-1-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add all three SATA IP blocks to the RK3588 DT.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230612171337.74576-6-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add all 3 combo PHYs that can be found in RK3588.
They are used for SATA, PCIe or USB3.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230612171337.74576-5-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add dts for Firefly Station P2.
Working IO:
* eMMC
* HDMI
* LAN
* LED
* SD Card
* UART
* USB2
* USB3
Signed-off-by: Furkan Kardame <f.kardame@manjaro.org>
Link: https://lore.kernel.org/r/20230620184746.55391-3-f.kardame@manjaro.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Station P2 is a single board computer by firefly based
on rk3568 soc
Signed-off-by: Furkan Kardame <f.kardame@manjaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230620184746.55391-2-f.kardame@manjaro.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

200MHz is the default rk3588 emmc max-frequency added in dtsi, so why
the board DT files are adding the same value explicitly?

Drop that unchanged property value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230621064507.479891-1-jagan@edgeble.aiSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add board-specific devicetree file for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230710115025.507439-4-chris.obbard@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add devicetree binding entry for the Radxa ROCK 4SE.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230710115025.507439-3-chris.obbard@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The ROCK 4SE uses the RK3399-T variant of the RK3399 SoC, which has some
changes to the OPP tables. Prepare for the bringup of this SoC by moving
the inclusion of existing OPP tables from the common devicetree into
each board-specific devicetree.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230710115025.507439-2-chris.obbard@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the necessary DT changes for the Rock 5A board to enable support for
the PWM controlled heat sink fan.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-14-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable ADC support for Rock 5A, which has the following ADC channels:

Channel 0 = Boot Mode Config
Channel 1 = Recovery Key
Channel 2 = PWM Fan
Channel 3 = Headphone Hook
Channel 4 = System Input Voltage
Channel 5 = Board ID Config
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-13-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

I2C3 is routed to the Camera connector and I2C5 is routed to the LCD
connector. On I2C5 additionally there is an unpopulated footprint for
a HYM8563TS RTC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-12-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the NPU regulator.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-11-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the I2C EEPROM to the Rock 5A DT.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-10-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add analog audio support based on the Everest Semi ES8316 codec.

Note, that this currently does not support headphone plug events. The
Rock 5A uses a different headphone jack with a different logic to detect
a headphone plug. Unfortunately the detect GPIO is always low.
Downstream uses an ADC channel instead, but that is currently not
supported upstream.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-9-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Describe the Rock 5A status LED in its device tree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-8-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add sdmmc support for Rock Pi 5A board.
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-7-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add GPIO controlled 5V regulator, which is used for supplying
the fan, on-board USB hub and HDMI.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230710165228.105983-6-sebastian.reichel@collabora.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>