- 22 Oct, 2015 19 commits
-
-
Trond Myklebust authored
commit 88de6af2 upstream. req->rq_private_buf isn't initialised when xprt_setup_backchannel calls xprt_free_allocation. Fixes: fb7a0b9a ("nfs41: New backchannel helper routines") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
Zefan Li <lizefan@huawei.com>
-
Chuck Lever authored
commit d683cc49 upstream. When encoding the NFSACL SETACL operation, reserve just the estimated size of the ACL rather than a fixed maximum. This eliminates needless zero padding on the wire that the server ignores. Fixes: ee5dc773 ('NFS: Fix "kernel BUG at fs/nfs/nfs3xdr.c:1338!"') Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
-
Olga Kornievskaia authored
commit e8d975e7 upstream. Problem: When an operation like WRITE receives a BAD_STATEID, even though recovery code clears the RECLAIM_NOGRACE recovery flag before recovering the open state, because of clearing delegation state for the associated inode, nfs_inode_find_state_and_recover() gets called and it makes the same state with RECLAIM_NOGRACE flag again. As a results, when we restart looking over the open states, we end up in the infinite loop instead of breaking out in the next test of state flags. Solution: unset the RECLAIM_NOGRACE set because of calling of nfs_inode_find_state_and_recover() after returning from calling recover_open() function. Signed-off-by:
Olga Kornievskaia <kolga@netapp.com> Signed-off-by:
-
Robert Schlabbach authored
commit fb6d1f7d upstream. Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset. Dissolve the function hub_port_finish_reset() completely and divide the actions to be taken into those which need to be done after each reset attempt and those which need to be done after the full procedure is complete, and place them in the appropriate places in hub_port_reset(). Also, remove an unneeded forward declaration of hub_port_reset(). Verbose Problem Description: USB 3.0 devices may be "lost for good" during a hub port reset. This makes Linux unable to boot from USB 3.0 devices in certain constellations of host controllers and devices, because the USB device is lost during initialization, preventing the rootfs from being mounted. The underlying problem is that in the affected constellations, during the processing inside hub_port_reset(), the hub link state goes from 0 to SS.inactive after the initial reset, and back to 0 again only after the following "warm" reset. However, hub_port_finish_reset() is called after each reset attempt and sets the state the connected USB device based on the "preliminary" status of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when the following warm reset is complete and hub_port_finish_reset() is called again, its call to set the device to USB_STATE_DEFAULT is blocked by usb_set_device_state() which does not allow taking USB devices out of USB_STATE_NOTATTACHED state. Thanks to Alan Stern for guiding me to the proper solution and how to submit it. Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27Signed-off-by:
Robert Schlabbach <robert_s@gmx.net> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [lizf: Backported to 3.4: - adjust context - s/usb_clear_port_feature/clear_port_feature - hub_port_warm_reset_required() takes only two arguments] Signed-off-by:
-
Haggai Eran authored
commit cab46214 upstream. With an RTL8191SU USB adaptor, sometimes the hints for a fragmented packet are set, but the packet length is too large. Allocate enough space to prevent memory corruption and a resulting kernel panic [1]. [1] http://www.spinics.net/lists/linux-wireless/msg136546.htmlSigned-off-by:
Haggai Eran <haggai.eran@gmail.com> ACKed-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Uwe Kleine-König authored
commit e5babdf9 upstream. Since commit bd31b859 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock that needs usage of the corresponding raw functions. This fixes: drivers/mtd/maps/dc21285.c: In function 'nw_en_write': drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type spin_lock_irqsave(&nw_gpio_lock, flags); In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline raw_spinlock_t *spinlock_check(spinlock_t *lock) ^ drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type spin_unlock_irqrestore(&nw_gpio_lock, flags); ^ In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags) Fixes: bd31b859 ("locking, ARM: Annotate low level hw locks as raw") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Paul E. McKenney authored
commit 6e91f8cb upstream. If, at the time __rcu_process_callbacks() is invoked, there are callbacks in Tiny RCU's callback list, but none of them are ready to be invoked, the current list-management code will knit the non-ready callbacks out of the list. This can result in hangs and possibly worse. This commit therefore inserts a check for there being no callbacks that can be invoked immediately. This bug is unlikely to occur -- you have to get a new callback between the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to __rcu_process_callbacks(). It was detected by the addition of RCU-bh testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's mutation testing. Although this bug was made much more likely by 915e8a4f (rcu: Remove fastpath from __rcu_process_callbacks()), this did not cause the bug, but rather made it much more probable. That said, it takes more than 40 hours of rcutorture testing, on average, for this bug to appear, so this fix cannot be considered an emergency. Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by:
Josh Triplett <josh@joshtriplett.org> [lizf: Backported to 3.4: adjust filename ] Signed-off-by:
-
Subbaraya Sundeep Bhatta authored
commit 76e838c9 upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by:
Subbaraya Sundeep Bhatta <sbhatta@xilinx.com> Fixes: 72246da4 (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Alex Deucher authored
commit 39fa10f7 upstream. Since we are messing with state in the worker. v2: drop the changes in the mst worker Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Dan Carpenter authored
commit e3958e9d upstream. These are used like: set_bit(WORK_LINK_UP, &priv->work_pending); The problem is that set_bit() takes the actual bit number and not a mask so static checkers get upset. It doesn't affect run time because we do it consistently, but we may as well clean it up. Fixes: 6010ce07 ('rndis_wlan: do link-down state change in worker thread') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Nicolas Ferre authored
commit 8687634b upstream. In RS485 mode, we may want to set the delay_rts_after_send value to 0. In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but this is exactly the expected behavior if we want no delay... Moreover, if the value was set to non-zero value by device-tree or earlier ioctl command, it was impossible to change it back to zero. Reported-by:
Sami Pietikäinen <Sami.Pietikainen@wapice.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Jesper Dangaard Brouer authored
commit 2a1ddf27 upstream. The pktgen.txt documentation still claimed that adding same device to multiple threads were not supported, but it have been since 2008 via commit e6fce5b9 ("pktgen: multiqueue etc."). Document this and describe the naming scheme dev@X, as the procfile name still need to be unique. Fixes: e6fce5b9 ("pktgen: multiqueue etc.") Signed-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Acked-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jesper Dangaard Brouer authored
commit d079abd1 upstream. Too many spaces were introduced in commit 63adc6fb ("pktgen: cleanup checkpatch warnings"), thus misaligning "src_min:" to other columns. Fixes: 63adc6fb ("pktgen: cleanup checkpatch warnings") Signed-off-by:
-
Axel Lin authored
commit 12c35005 upstream. WM8955_K_8_0_MASK bits is controlled by WM8955_PLL_CONTROL_3 rather than WM8955_PLL_CONTROL_2. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Axel Lin authored
commit ebb6ad73 upstream. VMID Control 0 BIT[2:1] is VMID Divider Enable and Select 00 = VMID disabled (for OFF mode) 01 = 2 x 50kΩ divider (for normal operation) 10 = 2 x 250kΩ divider (for low power standby) 11 = 2 x 5kΩ divider (for fast start-up) So WM8903_VMID_RES_250K should be 2 << 1, which is 4. Signed-off-by:
-
Axel Lin authored
commit 14ba3ec1 upstream. According to the datasheet: R10 (0Ah) VMID Impedance Control BIT 3:2 VMIDSEL DEFAULT 00 DESCRIPTION: VMID impedance selection control 00: 75kΩ output 01: 300kΩ output 10: 2.5kΩ output WM8737_VMIDSEL_MASK is 0xC (VMIDSEL - [3:2]), so it needs to left shift WM8737_VMIDSEL_SHIFT bits for setting these bits. Signed-off-by:
-
Horia Geant? authored
commit 5fa7dadc upstream. Fixes: 1d11911a ("crypto: talitos - fix warning: 'alg' may be used uninitialized in this function") Signed-off-by:
Horia Geanta <horia.geanta@freescale.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Brian Norris authored
commit 073db4a5 upstream. On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to mtd->usecount were done without taking mtd_table_mutex. kernel: Call Trace: kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50 kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8 kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200 kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30 kernel: [<ffffffff8022006c>] __fput+0xac/0x250 kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120 kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18 kernel: kernel: Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003 00000000 0040f809 00000000 kernel: ---[ end trace 080fbb4579b47a73 ]--- Fixed by taking the mutex in blktrans_open and blktrans_release. Note that this locking is already suggested in include/linux/mtd/blktrans.h: struct mtd_blktrans_ops { ... /* Called with mtd_table_mutex held; no race with add/remove */ int (*open)(struct mtd_blktrans_dev *dev); void (*release)(struct mtd_blktrans_dev *dev); ... }; But we weren't following it. Originally reported by (and patched by) Zhang and Giuseppe, independently. Improved and rewritten. Reported-by:
Zhang Xingcai <zhangxingcai@huawei.com> Reported-by:
Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by:
-
Peter Zijlstra authored
commit 5de2755c upstream. Because we drop cpu_base->lock around calling hrtimer::function, it is possible for hrtimer_start() to come in between and enqueue the timer. If hrtimer::function then returns HRTIMER_RESTART we'll hit the BUG_ON because HRTIMER_STATE_ENQUEUED will be set. Since the above is a perfectly valid scenario, remove the BUG_ON and make the enqueue_hrtimer() call conditional on the timer not being enqueued already. NOTE: in that concurrent scenario its entirely common for both sites to want to modify the hrtimer, since hrtimers don't provide serialization themselves be sure to provide some such that the hrtimer::function and the hrtimer_start() caller don't both try and fudge the expiration state at the same time. To that effect, add a WARN when someone tries to forward an already enqueued timer, the most common way to change the expiry of self restarting timers. Ideally we'd put the WARN in everything modifying the expiry but most of that is inlines and we don't need the bloat. Fixes: 2d44ae4d ("hrtimer: clean up cpu->base locking tricks") Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Ben Segall <bsegall@google.com> Cc: Roman Gushchin <klamm@yandex-team.ru> Cc: Paul Turner <pjt@google.com> Link: http://lkml.kernel.org/r/20150415113105.GT5029@twins.programming.kicks-ass.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
- 18 Sep, 2015 21 commits
-
-
Zefan Li authored
-
Eric Dumazet authored
commit beb39db5 upstream. We have two problems in UDP stack related to bogus checksums : 1) We return -EAGAIN to application even if receive queue is not empty. This breaks applications using edge trigger epoll() 2) Under UDP flood, we can loop forever without yielding to other processes, potentially hanging the host, especially on non SMP. This patch is an attempt to make things better. We might in the future add extra support for rt applications wanting to better control time spent doing a recv() in a hostile environment. For example we could validate checksums before queuing packets in socket receive queue. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Thomas Gleixner authored
commit 81a44c54 upstream. The following scenario does not work correctly: Runqueue of CPUx contains two runnable and pinned tasks: T1: SCHED_FIFO, prio 80 T2: SCHED_FIFO, prio 80 T1 is on the cpu and executes the following syscalls (classic priority ceiling scenario): sys_sched_setscheduler(pid(T1), SCHED_FIFO, .prio = 90); ... sys_sched_setscheduler(pid(T1), SCHED_FIFO, .prio = 80); ... Now T1 gets preempted by T3 (SCHED_FIFO, prio 95). After T3 goes back to sleep the scheduler picks T2. Surprise! The same happens w/o actual preemption when T1 is forced into the scheduler due to a sporadic NEED_RESCHED event. The scheduler invokes pick_next_task() which returns T2. So T1 gets preempted and scheduled out. This happens because sched_setscheduler() dequeues T1 from the prio 90 list and then enqueues it on the tail of the prio 80 list behind T2. This violates the POSIX spec and surprises user space which relies on the guarantee that SCHED_FIFO tasks are not scheduled out unless they give the CPU up voluntarily or are preempted by a higher priority task. In the latter case the preempted task must get back on the CPU after the preempting task schedules out again. We fixed a similar issue already in commit 60db48ca (sched: Queue a deboosted task to the head of the RT prio queue). The same treatment is necessary for sched_setscheduler(). So enqueue to head of the prio bucket list if the priority of the task is lowered. It might be possible that existing user space relies on the current behaviour, but it can be considered highly unlikely due to the corner case nature of the application scenario. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Ben Hutchings authored
pipe_iov_copy_{from,to}_user() may be tried twice with the same iovec, the first time atomically and the second time not. The second attempt needs to continue from the iovec position, pipe buffer offset and remaining length where the first attempt failed, but currently the pipe buffer offset and remaining length are reset. This will corrupt the piped data (possibly also leading to an information leak between processes) and may also corrupt kernel memory. This was fixed upstream by commits f0d1bec9 ("new helper: copy_page_from_iter()") and 637b58c2 ("switch pipe_read() to copy_page_to_iter()"), but those aren't suitable for stable. This fix for older kernel versions was made by Seth Jennings for RHEL and I have extracted it from their update. CVE-2015-1805 References: https://bugzilla.redhat.com/show_bug.cgi?id=1202855Signed-off-by:Ben Hutchings <ben@decadent.org.uk> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Ralf Baechle authored
commit d496f784 upstream. A ROSE socket doesn't necessarily always have a neighbour pointer so check if the neighbour pointer is valid before dereferencing it. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Tested-by:
Bernard Pidoux <f6bvp@free.fr> Signed-off-by:
-
Dan Williams authored
commit 4d66e5e9 upstream. ================================= [ INFO: inconsistent lock state ] 4.1.0-rc7+ #217 Tainted: G O --------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. swapper/6/0 [HC0[0]:SC1[1]:HE1:SE0] takes: (ext_devt_lock){+.?...}, at: [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 {SOFTIRQ-ON-W} state was registered at: [<ffffffff810bf6b1>] __lock_acquire+0x461/0x1e70 [<ffffffff810c1947>] lock_acquire+0xb7/0x290 [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50 [<ffffffff8143a07d>] blk_alloc_devt+0x6d/0xd0 <-- take the lock in process context [..] [<ffffffff810bf64e>] __lock_acquire+0x3fe/0x1e70 [<ffffffff810c00ad>] ? __lock_acquire+0xe5d/0x1e70 [<ffffffff810c1947>] lock_acquire+0xb7/0x290 [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70 [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50 [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70 [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 <-- take the lock in softirq [<ffffffff8143bfec>] part_release+0x1c/0x50 [<ffffffff8158edf6>] device_release+0x36/0xb0 [<ffffffff8145ac2b>] kobject_cleanup+0x7b/0x1a0 [<ffffffff8145aad0>] kobject_put+0x30/0x70 [<ffffffff8158f147>] put_device+0x17/0x20 [<ffffffff8143c29c>] delete_partition_rcu_cb+0x16c/0x180 [<ffffffff8143c130>] ? read_dev_sector+0xa0/0xa0 [<ffffffff810e0e0f>] rcu_process_callbacks+0x2ff/0xa90 [<ffffffff810e0dcf>] ? rcu_process_callbacks+0x2bf/0xa90 [<ffffffff81067e2e>] __do_softirq+0xde/0x600 Neil sees this in his tests and it also triggers on pmem driver unbind for the libnvdimm tests. This fix is on top of an initial fix by Keith for incorrect usage of mutex_lock() in this path: 2da78092 "block: Fix dev_t minor allocation lifetime". Both this and 2da78092 are candidates for -stable. Fixes: 2da78092 ("block: Fix dev_t minor allocation lifetime") Cc: Keith Busch <keith.busch@intel.com> Reported-by:
NeilBrown <neilb@suse.de> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Jens Axboe <axboe@fb.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Vasily Averin authored
commit aff09ce3 upstream. Currently bridge can silently drop ipv4 fragments. If node have loaded nf_defrag_ipv4 module but have no nf_conntrack_ipv4, br_nf_pre_routing defragments incoming ipv4 fragments but nfct check in br_nf_dev_queue_xmit does not allow re-fragment combined packet back, and therefore it is dropped in br_dev_queue_push_xmit without incrementing of any failcounters It seems the only way to hit the ip_fragment code in the bridge xmit path is to have a fragment list whose reassembled fragments go over the mtu. This only happens if nf_defrag is enabled. Thanks to Florian Westphal for providing feedback to clarify this. Defragmentation ipv4 is required not only in conntracks but at least in TPROXY target and socket match, therefore #ifdef is changed from NF_CONNTRACK_IPV4 to NF_DEFRAG_IPV4 Signed-off-by:
Vasily Averin <vvs@openvz.org> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Cc: Kirill Tkhai <ktkhai@odin.com> Signed-off-by:
-
Junling Zheng authored
Based on 08adb7da upstream. We found that after v3.10.73, recvmsg might return -EFAULT while -EINVAL was expected. We tested it through the recvmsg01 testcase come from LTP testsuit. It set msg->msg_namelen to -1 and the recvmsg syscall returned errno 14, which is unexpected (errno 22 is expected): recvmsg01 4 TFAIL : invalid socket length ; returned -1 (expected -1), errno 14 (expected 22) Linux mainline has no this bug for commit 08adb7da fixes it accidentally. However, it is too large and complex to be backported to LTS 3.10. Commit 281c9c36 (net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour) made get_compat_msghdr() return error if msg_sys->msg_namelen was negative, which changed the behaviors of recvmsg and sendmsg syscall in a lib32 system: Before commit 281c9c36, get_compat_msghdr() wouldn't fail and it would return -EINVAL in move_addr_to_user() or somewhere if msg_sys->msg_namelen was invalid and then syscall returned -EINVAL, which is correct. And now, when msg_sys->msg_namelen is negative, get_compat_msghdr() will fail and wants to return -EINVAL, however, the outer syscall will return -EFAULT directly, which is unexpected. This patch gets the return value of get_compat_msghdr() as well as copy_msghdr_from_user(), then returns this expected value if get_compat_msghdr() fails. Fixes: 281c9c36 (net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour) Signed-off-by:
Junling Zheng <zhengjunling@huawei.com> Signed-off-by:
Hanbing Xu <xuhanbing@huawei.com> Cc: Li Zefan <lizefan@huawei.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: David Miller <davem@davemloft.net> Signed-off-by:
-
Xie XiuQi authored
commit e21404dc upstream. Loading ipmi_si module while bmc is disconnected, we found the timeout is longer than 5 secs. Actually it takes about 3 mins and 20 secs.(HZ=250) error message as below: Dec 12 19:08:59 linux kernel: IPMI BT: timeout in RD_WAIT [ ] 1 retries left Dec 12 19:08:59 linux kernel: BT: write 4 bytes seq=0x01 03 18 00 01 [...] Dec 12 19:12:19 linux kernel: IPMI BT: timeout in RD_WAIT [ ] Dec 12 19:12:19 linux kernel: failed 2 retries, sending error response Dec 12 19:12:19 linux kernel: IPMI: BT reset (takes 5 secs) Dec 12 19:12:19 linux kernel: IPMI BT: flag reset [ ] Function wait_for_msg_done() use schedule_timeout_uninterruptible(1) to sleep 1 tick, so we should subtract jiffies_to_usecs(1) instead of 100 usecs from timeout. Reported-by:
Hu Shiyuan <hushiyuan@huawei.com> Signed-off-by:
Xie XiuQi <xiexiuqi@huawei.com> Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Suresh Siddha authored
commit b1a74bf8 upstream. Preemption is disabled between kernel_fpu_begin/end() and as such it is not a good idea to use these routines in kvm_load/put_guest_fpu() which can be very far apart. kvm_load/put_guest_fpu() routines are already called with preemption disabled and KVM already uses the preempt notifier to save the guest fpu state using kvm_put_guest_fpu(). So introduce __kernel_fpu_begin/end() routines which don't touch preemption and use them instead of kernel_fpu_begin/end() for KVM's use model of saving/restoring guest FPU state. Also with this change (and with eagerFPU model), fix the host cr0.TS vm-exit state in the case of VMX. For eagerFPU case, host cr0.TS is always clear. So no need to worry about it. For the traditional lazyFPU restore case, change the cr0.TS bit for the host state during vm-exit to be always clear and cr0.TS bit is set in the __vmx_load_host_state() when the FPU (guest FPU or the host task's FPU) state is not active. This ensures that the host/guest FPU state is properly saved, restored during context-switch and with interrupts (using irq_fpu_usable()) not stomping on the active FPU state. Signed-off-by:
Suresh Siddha <suresh.b.siddha@intel.com> Link: http://lkml.kernel.org/r/1348164109.26695.338.camel@sbsiddha-desk.sc.intel.com Cc: Avi Kivity <avi@redhat.com> Signed-off-by:
H. Peter Anvin <hpa@linux.intel.com> Signed-off-by:
Rui Xiang <rui.xiang@huawei.com> Signed-off-by:
-
Suresh Siddha authored
commit 9c1c3fac upstream. kvm's guest fpu save/restore should be wrapped around kernel_fpu_begin/end(). This will avoid for example taking a DNA in kvm_load_guest_fpu() when it tries to load the fpu immediately after doing unlazy_fpu() on the host side. More importantly this will prevent the host process fpu from being corrupted. Signed-off-by:
-
David S. Miller authored
commit a134f083 upstream. If we don't do that, then the poison value is left in the ->pprev backlink. This can cause crashes if we do a disconnect, followed by a connect(). Tested-by:
Wen Xu <hotdog3645@gmail.com> Signed-off-by:
-
Benjamin Randazzo authored
commit b6878d9e upstream. In drivers/md/md.c get_bitmap_file() uses kmalloc() for creating a mdu_bitmap_file_t called "file". 5769 file = kmalloc(sizeof(*file), GFP_NOIO); 5770 if (!file) 5771 return -ENOMEM; This structure is copied to user space at the end of the function. 5786 if (err == 0 && 5787 copy_to_user(arg, file, sizeof(*file))) 5788 err = -EFAULT But if bitmap is disabled only the first byte of "file" is initialized with zero, so it's possible to read some bytes (up to 4095) of kernel space memory from user space. This is an information leak. 5775 /* bitmap disabled, zero the first byte and copy out */ 5776 if (!mddev->bitmap_info.file) 5777 file->pathname[0] = '\0'; Signed-off-by:
Benjamin Randazzo <benjamin@randazzo.fr> Signed-off-by:
NeilBrown <neilb@suse.com> [lizf: Backported to 3.4: fix both branches] Signed-off-by:
-
Jan Kara authored
commit 23b133bd upstream. Check length of extended attributes and allocation descriptors when loading inodes from disk. Otherwise corrupted filesystems could confuse the code and make the kernel oops. Reported-by:
Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by:
Jan Kara <jack@suse.cz> [lizf: Backported to 3.4: - call make_bad_inode() and then return - relace bs with inode->i_sb->s_blocksize] Signed-off-by:
-
Steven Rostedt authored
commit 2cf30dc1 upstream. When the following filter is used it causes a warning to trigger: # cd /sys/kernel/debug/tracing # echo "((dev==1)blocks==2)" > events/ext4/ext4_truncate_exit/filter -bash: echo: write error: Invalid argument # cat events/ext4/ext4_truncate_exit/filter ((dev==1)blocks==2) ^ parse_error: No error ------------[ cut here ]------------ WARNING: CPU: 2 PID: 1223 at kernel/trace/trace_events_filter.c:1640 replace_preds+0x3c5/0x990() Modules linked in: bnep lockd grace bluetooth ... CPU: 3 PID: 1223 Comm: bash Tainted: G W 4.1.0-rc3-test+ #450 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012 0000000000000668 ffff8800c106bc98 ffffffff816ed4f9 ffff88011ead0cf0 0000000000000000 ffff8800c106bcd8 ffffffff8107fb07 ffffffff8136b46c ffff8800c7d81d48 ffff8800d4c2bc00 ffff8800d4d4f920 00000000ffffffea Call Trace: [<ffffffff816ed4f9>] dump_stack+0x4c/0x6e [<ffffffff8107fb07>] warn_slowpath_common+0x97/0xe0 [<ffffffff8136b46c>] ? _kstrtoull+0x2c/0x80 [<ffffffff8107fb6a>] warn_slowpath_null+0x1a/0x20 [<ffffffff81159065>] replace_preds+0x3c5/0x990 [<ffffffff811596b2>] create_filter+0x82/0xb0 [<ffffffff81159944>] apply_event_filter+0xd4/0x180 [<ffffffff81152bbf>] event_filter_write+0x8f/0x120 [<ffffffff811db2a8>] __vfs_write+0x28/0xe0 [<ffffffff811dda43>] ? __sb_start_write+0x53/0xf0 [<ffffffff812e51e0>] ? security_file_permission+0x30/0xc0 [<ffffffff811dc408>] vfs_write+0xb8/0x1b0 [<ffffffff811dc72f>] SyS_write+0x4f/0xb0 [<ffffffff816f5217>] system_call_fastpath+0x12/0x6a ---[ end trace e11028bd95818dcd ]--- Worse yet, reading the error message (the filter again) it says that there was no error, when there clearly was. The issue is that the code that checks the input does not check for balanced ops. That is, having an op between a closed parenthesis and the next token. This would only cause a warning, and fail out before doing any real harm, but it should still not caues a warning, and the error reported should work: # cd /sys/kernel/debug/tracing # echo "((dev==1)blocks==2)" > events/ext4/ext4_truncate_exit/filter -bash: echo: write error: Invalid argument # cat events/ext4/ext4_truncate_exit/filter ((dev==1)blocks==2) ^ parse_error: Meaningless filter expression And give no kernel warning. Link: http://lkml.kernel.org/r/20150615175025.7e809215@gandalf.local.home Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Tested-by:
Steven Rostedt <rostedt@goodmis.org> [lizf: Backported to 3.4: remove the check for OP_NOT, as it's not supported.] Signed-off-by:
-
Wang Long authored
commit 10802932 upstream. The producer should be used producer_fifo as its sched_priority, so correct it. Link: http://lkml.kernel.org/r/1433923957-67842-1-git-send-email-long.wanglong@huawei.comSigned-off-by:
Wang Long <long.wanglong@huawei.com> Signed-off-by:
-
Nikolay Aleksandrov authored
commit 1a040eac upstream. Since the addition of sysfs multicast router support if one set multicast_router to "2" more than once, then the port would be added to the hlist every time and could end up linking to itself and thus causing an endless loop for rlist walkers. So to reproduce just do: echo 2 > multicast_router; echo 2 > multicast_router; in a bridge port and let some igmp traffic flow, for me it hangs up in br_multicast_flood(). Fix this by adding a check in br_multicast_add_router() if the port is already linked. The reason this didn't happen before the addition of multicast_router sysfs entries is because there's a !hlist_unhashed check that prevents it. Signed-off-by:
Nikolay Aleksandrov <razor@blackwall.org> Fixes: 0909e117 ("bridge: Add multicast_router sysfs entries") Acked-by:
-
Nikolay Aleksandrov authored
commit c4c832f8 upstream. br_fdb_update() can be called in process context in the following way: br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set) so we need to disable softirqs because there are softirq users of the hash_lock. One easy way to reproduce this is to modify the bridge utility to set NTF_USE, enable stp and then set maxageing to a low value so br_fdb_cleanup() is called frequently and then just add new entries in a loop. This happens because br_fdb_cleanup() is called from timer/softirq context. The spin locks in br_fdb_update were _bh before commit f8ae737d ("[BRIDGE]: forwarding remove unneeded preempt and bh diasables") and at the time that commit was correct because br_fdb_update() couldn't be called from process context, but that changed after commit: 292d1398 ("bridge: add NTF_USE support") Using local_bh_disable/enable around br_fdb_update() allows us to keep using the spin_lock/unlock in br_fdb_update for the fast-path. Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: 292d1398 ("bridge: add NTF_USE support") Signed-off-by:
-
Wilson Kok authored
commit 1d7c4903 upstream. br_fdb_update() can be called in process context in the following way: br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set) so we need to use spin_lock_bh because there are softirq users of the hash_lock. One easy way to reproduce this is to modify the bridge utility to set NTF_USE, enable stp and then set maxageing to a low value so br_fdb_cleanup() is called frequently and then just add new entries in a loop. This happens because br_fdb_cleanup() is called from timer/softirq context. These locks were _bh before commit f8ae737d ("[BRIDGE]: forwarding remove unneeded preempt and bh diasables") and at the time that commit was correct because br_fdb_update() couldn't be called from process context, but that changed after commit: 292d1398 ("bridge: add NTF_USE support") Signed-off-by:
Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by:
-
James Hogan authored
commit 5f35b9cd upstream. Commit 334c86c4 ("MIPS: IRQ: Add stackoverflow detection") added kernel stack overflow detection, however it only enabled it conditional upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW, which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so switch it to using that definition instead. Fixes: 334c86c4 ("MIPS: IRQ: Add stackoverflow detection") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Adam Jiang <jiang.adam@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: http://patchwork.linux-mips.org/patch/10531/Signed-off-by:
-
John D. Blair authored
commit df72d588 upstream. Added the USB serial device ID for the HubZ dual ZigBee and Z-Wave radio dongle. Signed-off-by:
John D. Blair <johnb@candicontrols.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
