- 13 Apr, 2020 34 commits
-
-
Petr Machata authored
[ Upstream commit ccfc5693 ] The handler for FLOW_ACTION_VLAN_MANGLE ends by returning whatever the lower-level function that it calls returns. If there are more actions lined up after this action, those are never offloaded. Fix by only bailing out when the called function returns an error. Fixes: a150201a ("mlxsw: spectrum: Add support for vlan modify TC action") Signed-off-by:
Petr Machata <petrm@mellanox.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Palethorpe authored
[ Upstream commit b9258a2c ] struct can_frame contains some padding which is not explicitly zeroed in slc_bump. This uninitialized data will then be transmitted if the stack initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL). This commit just zeroes the whole struct including the padding. Signed-off-by:
Richard Palethorpe <rpalethorpe@suse.com> Fixes: a1044e36 ("can: add slcan driver for serial/USB-serial CAN adapters") Reviewed-by:
Kees Cook <keescook@chromium.org> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: security@kernel.org Cc: wg@grandegger.com Cc: mkl@pengutronix.de Cc: davem@davemloft.net Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Jisheng Zhang authored
[ Upstream commit 3e1221ac ] Commit 9463c445 ("net: stmmac: dwmac1000: Clear unused address entries") cleared the unused mac address entries, but introduced an out-of bounds mac address register programming bug -- After setting the secondary unicast mac addresses, the "reg" value has reached netdev_uc_count() + 1, thus we should only clear address entries if (addr < perfect_addr_number) Fixes: 9463c445 ("net: stmmac: dwmac1000: Clear unused address entries") Signed-off-by:
Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by:
-
Oleksij Rempel authored
[ Upstream commit 6110dff7 ] After the power-down bit is cleared, the chip internally triggers a global reset. According to the KSZ9031 documentation, we have to wait at least 1ms for the reset to finish. If the chip is accessed during reset, read will return 0xffff, while write will be ignored. Depending on the system performance and MDIO bus speed, we may or may not run in to this issue. This bug was discovered on an iMX6QP system with KSZ9031 PHY and attached PHY interrupt line. If IRQ was used, the link status update was lost. In polling mode, the link status update was always correct. The investigation showed, that during a read-modify-write access, the read returned 0xffff (while the chip was still in reset) and corresponding write hit the chip _after_ reset and triggered (due to the 0xffff) another reset in an undocumented bit (register 0x1f, bit 1), resulting in the next write being lost due to the new reset cycle. This patch fixes the issue by adding a 1...2 ms sleep after the genphy_resume(). Fixes: 836384d2 ("net: phy: micrel: Add specific suspend") Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit afa3b592 ] When the bcm_sf2 was converted into a proper platform device driver and used the new dsa_register_switch() interface, we would still be parsing the legacy DSA node that contained all the port information since the platform firmware has intentionally maintained backward and forward compatibility to client programs. Ensure that we do parse the correct node, which is "ports" per the revised DSA binding. Fixes: d9338023 ("net: dsa: bcm_sf2: Make it a real platform device driver") Signed-off-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 536fab5b ] We were registering our slave MDIO bus with OF and doing so with assigning the newly created slave_mii_bus of_node to the master MDIO bus controller node. This is a bad thing to do for a number of reasons: - we are completely lying about the slave MII bus is arranged and yet we still want to control which MDIO devices it probes. It was attempted before to play tricks with the bus_mask to perform that: https://www.spinics.net/lists/netdev/msg429420.html but the approach was rightfully rejected - the device_node reference counting is messed up and we are effectively doing a double probe on the devices we already probed using the master, this messes up all resources reference counts (such as clocks) The proper fix for this as indicated by David in his reply to the thread above is to use a platform data style registration so as to control exactly which devices we probe: https://www.spinics.net/lists/netdev/msg430083.html By using mdiobus_register(), our slave_mii_bus->phy_mask value is used as intended, and all the PHY addresses that must be redirected towards our slave MDIO bus is happening while other addresses get redirected towards the master MDIO bus. Fixes: 461cd1b0 ("net: dsa: bcm_sf2: Register our slave MDIO bus") Signed-off-by:
-
Jarod Wilson authored
[ Upstream commit 744fdc82 ] Bonding slave and team port devices should not have link-local addresses automatically added to them, as it can interfere with openvswitch being able to properly add tc ingress. Basic reproducer, courtesy of Marcelo: $ ip link add name bond0 type bond $ ip link set dev ens2f0np0 master bond0 $ ip link set dev ens2f1np2 master bond0 $ ip link set dev bond0 up $ ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff 5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc mq master bond0 state DOWN group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff 11: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link valid_lft forever preferred_lft forever (above trimmed to relevant entries, obviously) $ sysctl net.ipv6.conf.ens2f0np0.addr_gen_mode=0 net.ipv6.conf.ens2f0np0.addr_gen_mode = 0 $ sysctl net.ipv6.conf.ens2f1np2.addr_gen_mode=0 net.ipv6.conf.ens2f1np2.addr_gen_mode = 0 $ ip a l ens2f0np0 2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative valid_lft forever preferred_lft forever $ ip a l ens2f1np2 5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc mq master bond0 state DOWN group default qlen 1000 link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative valid_lft forever preferred_lft forever Looks like addrconf_sysctl_addr_gen_mode() bypasses the original "is this a slave interface?" check added by commit c2edacf8, and results in an address getting added, while w/the proposed patch added, no address gets added. This simply adds the same gating check to another code path, and thus should prevent the same devices from erroneously obtaining an ipv6 link-local address. Fixes: d35a00b8 ("net/ipv6: allow sysctl to change link-local address generation mode") Reported-by:
Moshe Levi <moshele@mellanox.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Marcelo Ricardo Leitner <mleitner@redhat.com> CC: netdev@vger.kernel.org Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Randy Dunlap authored
commit aa9f7d51 upstream. Using an empty (malformed) nodelist that is not caught during mount option parsing leads to a stack-out-of-bounds access. The option string that was used was: "mpol=prefer:,". However, MPOL_PREFERRED requires a single node number, which is not being provided here. Add a check that 'nodes' is not empty after parsing for MPOL_PREFERRED's nodeid. Fixes: 095f1fc4 ("mempolicy: rework shmem mpol parsing and display") Reported-by:
Entropy Moe <3ntr0py1337@gmail.com> Reported-by: syzbot+b055b1a6b2b958707a21@syzkaller.appspotmail.com Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Tested-by: syzbot+b055b1a6b2b958707a21@syzkaller.appspotmail.com Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Link: http://lkml.kernel.org/r/89526377-7eb6-b662-e1d8-4430928abde9@infradead.orgSigned-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Sam Protsenko authored
commit 94e297c5 upstream. ctags indexing ("make tags" command) throws this warning: ctags: Warning: include/linux/notifier.h:125: null expansion of name pattern "\1" This is the result of DEFINE_PER_CPU() macro expansion. Fix that by getting rid of line break. Similar fix was already done in commit 25528213 ("tags: Fix DEFINE_PER_CPU expansions"), but this one probably wasn't noticed. Link: http://lkml.kernel.org/r/20181030202808.28027-1-semen.protsenko@linaro.org Fixes: 9c80172b ("kernel/SRCU: provide a static initializer") Signed-off-by:
Sam Protsenko <semen.protsenko@linaro.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
-
Miklos Szeredi authored
commit 18127429 upstream. Unprotected naming of local variables within the set_mask_bits() can easily lead to using the wrong scope. Noticed this when "set_mask_bits(&foo->bar, 0, mask)" behaved as no-op. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Fixes: 00a1a053 ("ext4: atomically set inode->i_flags in ext4_set_inode_flags()") Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Daniel Jordan authored
commit 38228e88 upstream. lockdep complains when padata's paths to update cpumasks via CPU hotplug and sysfs are both taken: # echo 0 > /sys/devices/system/cpu/cpu1/online # echo ff > /sys/kernel/pcrypt/pencrypt/parallel_cpumask ====================================================== WARNING: possible circular locking dependency detected 5.4.0-rc8-padata-cpuhp-v3+ #1 Not tainted ------------------------------------------------------ bash/205 is trying to acquire lock: ffffffff8286bcd0 (cpu_hotplug_lock.rw_sem){++++}, at: padata_set_cpumask+0x2b/0x120 but task is already holding lock: ffff8880001abfa0 (&pinst->lock){+.+.}, at: padata_set_cpumask+0x26/0x120 which lock already depends on the new lock. padata doesn't take cpu_hotplug_lock and pinst->lock in a consistent order. Which should be first? CPU hotplug calls into padata with cpu_hotplug_lock already held, so it should have priority. Fixes: 6751fb3c ("padata: Use get_online_cpus/put_online_cpus") Signed-off-by:
Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Amritha Nambiar authored
commit 6e11d157 upstream. Fixes the lower and upper bounds when there are multiple TCs and traffic is on the the same TC on the same device. The lower bound is represented by 'qoffset' and the upper limit for hash value is 'qcount + qoffset'. This gives a clean Rx to Tx queue mapping when there are multiple TCs, as the queue indices for upper TCs will be offset by 'qoffset'. v2: Fixed commit description based on comments. Fixes: 1b837d48 ("net: Revoke export for __skb_tx_hash, update it to just be static skb_tx_hash") Fixes: eadec877 ("net: Add support for subordinate traffic classes to netdev_pick_tx") Signed-off-by:
Amritha Nambiar <amritha.nambiar@intel.com> Reviewed-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Reviewed-by:
Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by:
-
David Howells authored
commit 498b5776 upstream. Fix the handling of sendmsg() with MSG_WAITALL for userspace to round the timeout for when a signal occurs up to at least two jiffies as a 1 jiffy timeout may end up being effectively 0 if jiffies wraps at the wrong time. Fixes: bc5e3a54 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Geoffrey Allott authored
commit e9097e47 upstream. I have a system which has an EVGA X99 Classified motherboard. The pin assignments for the HD Audio controller are not correct under Linux. Windows 10 works fine and informs me that it's using the Recon3Di driver, and on Linux, `cat /sys/class/sound/card0/device/subsystem_{vendor,device}` yields 0x3842 0x1038 This patch adds a corresponding entry to the quirk list. Signed-off-by:
Geoffrey Allott <geoffrey@allott.email> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/a6cd56b678c00ce2db3685e4278919f2584f8244.camel@allott.emailSigned-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Hans de Goede authored
commit 9c80662a upstream. Some HP Pavilion x2 10 models use an AXP288 for charging and fuel-gauge. We use a native power_supply / PMIC driver in this case, because on most models with an AXP288 the ACPI AC / Battery code is either completely missing or relies on custom / proprietary ACPI OpRegions which Linux does not implement. The native drivers mostly work fine, but there are 2 problems: 1. These model uses a Type-C connector for charging which the AXP288 does not support. As long as a Type-A charger (which uses the USB data pins for charger type detection) is used everything is fine. But if a Type-C charger is used (such as the charger shipped with the device) then the charger is not recognized. So we end up slowly discharging the device even though a charger is connected, because we are limiting the current from the charger to 500mA. To make things worse this happens with the device's official charger. Looking at the ACPI tables HP has "solved" the problem of the AXP288 not being able to recognize Type-C chargers by simply always programming the input-current-limit at 3000mA and relying on a Vhold setting of 4.7V (normally 4.4V) to limit the current intake if the charger cannot handle this. 2. If no charger is connected when the machine boots then it boots with the vbus-path disabled. On other devices this is done when a 5V boost converter is active to avoid the PMIC trying to charge from the 5V boost output. This is done when an OTG host cable is inserted and the ID pin on the micro-B receptacle is pulled low, the ID pin has an ACPI event handler associated with it which re-enables the vbus-path when the ID pin is pulled high when the OTG cable is removed. The Type-C connector has no ID pin, there is no ID pin handler and there appears to be no 5V boost converter, so we end up not charging because the vbus-path is disabled, until we unplug the charger which automatically clears the vbus-path disable bit and then on the second plug-in of the adapter we start charging. The HP Pavilion x2 10 models with an AXP288 do have mostly working ACPI AC / Battery code which does not rely on custom / proprietary ACPI OpRegions. So one possible solution would be to blacklist the AXP288 native power_supply drivers and add the HP Pavilion x2 10 with AXP288 DMI ids to the list of devices which should use the ACPI AC / Battery code even though they have an AXP288 PMIC. This would require changes to 4 files: drivers/acpi/ac.c, drivers/power/supply/axp288_charger.c, drivers/acpi/battery.c and drivers/power/supply/axp288_fuel_gauge.c. Beside needing adding the same DMI matches to 4 different files, this approach also triggers problem 2. from above, but then when suspended, during suspend the machine will not wakeup because the vbus path is disabled by the AML code when not charging, so the Vbus low-to-high IRQ is not triggered, the CPU never wakes up and the device does not charge even though the user likely things it is charging, esp. since the charge status LED is directly coupled to an adapter being plugged in and does not reflect actual charging. This could be worked by enabling vbus-path explicitly from say the axp288_charger driver's suspend handler. So neither situation is ideal, in both cased we need to explicitly enable the vbus-path to work around different variants of problem 2 above, this requires a quirk in the axp288_charger code. If we go the route of using the ACPI AC / Battery drivers then we need modifications to 3 other drivers; and we need to partially disable the axp288_charger code, while at the same time keeping it around to enable vbus-path on suspend. OTOH we can copy the hardcoding of 3A input-current-limit (we never touch Vhold, so that would stay at 4.7V) to the axp288_charger code, which needs changes regardless, then we concentrate all special handling of this interesting device model in the axp288_charger code. That is what this commit does. Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1791098Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by:
-
Hans de Goede authored
commit 9c945530 upstream. On devices with an AXP288, we need to wakeup from suspend when a charger is plugged in, so that we can do charger-type detection and so that the axp288-charger driver, which listens for our extcon events, can configure the input-current-limit accordingly. Cc: stable@vger.kernel.org Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
Alexander Usyskin authored
commit 99397d33 upstream. Add Cedar Fork (CDF) device ids, those belongs to the cannon point family. Cc: <stable@vger.kernel.org> Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20200324210730.17672-1-tomas.winkler@intel.comSigned-off-by:
-
Eugene Syromiatnikov authored
commit 9b6eaaf3 upstream. The BIT() macro definition is not available for the UAPI headers (moreover, it can be defined differently in the user space); replace its usage with the _BITUL() macro that is defined in <linux/const.h>. Fixes: 237483aa ("coresight: stm: adding driver for CoreSight STM component") Signed-off-by:
Eugene Syromiatnikov <esyr@redhat.com> Cc: stable <stable@vger.kernel.org> Reviewed-by:
Mathieu Poirier <mathieu.poirier@linaro.org> Link: https://lore.kernel.org/r/20200324042213.GA10452@asgard.redhat.comSigned-off-by:
-
Kishon Vijay Abraham I authored
commit b2ba9225 upstream. commit e0332712 ("pci_endpoint_test: Add 2 ioctl commands") uses module parameter 'irqtype' in pci_endpoint_test_set_irq() to check if IRQ vectors of a particular type (MSI or MSI-X or LEGACY) is already allocated. However with multi-function devices, 'irqtype' will not correctly reflect the IRQ type of the PCI device. Fix it here by adding 'irqtype' for each PCI device to show the IRQ type of a particular PCI device. Fixes: e0332712 ("pci_endpoint_test: Add 2 ioctl commands") Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org # v4.19+ Signed-off-by:
-
Kishon Vijay Abraham I authored
commit 6b443e5c upstream. Adding more than 10 pci-endpoint-test devices results in "kobject_add_internal failed for pci-endpoint-test.1 with -EEXIST, don't try to register things with the same name in the same directory". This is because commit 2c156ac7 ("misc: Add host side PCI driver for PCI test function device") limited the length of the "name" to 20 characters. Change the length of the name to 24 in order to support upto 10000 pci-endpoint-test devices. Fixes: 2c156ac7 ("misc: Add host side PCI driver for PCI test function device") Signed-off-by:
-
YueHaibing authored
commit 10cea23b upstream. rts522a should use rts522a_pcr_ops, which is diffrent with rts5227 in phy/hw init setting. Fixes: ce6a5acc ("mfd: rtsx: Add support for rts522A") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200326032618.20472-1-yuehaibing@huawei.comSigned-off-by:
-
Sean Young authored
commit 5c4c8b4a upstream. The IR signal to control the Panasonic ACXA75C00600 air conditioner has 439 pulse/spaces. Increase limit to make it possible to transmit signal. Reported-by:
Takashi Kanamaru <neuralassembly@gmail.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Lucas Stach authored
commit 4900dda9 upstream. If a MMU is shared between multiple GPUs, all of them need to flush their TLBs, so a single marker that gets reset on the first flush won't do. Replace the flush marker with a sequence number, so that it's possible to check if the TLB is in sync with the current page table state for each GPU. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
Guido Günther <agx@sigxcpu.org> Signed-off-by:
Robert Beckett <bob.beckett@collabora.com> Signed-off-by:
-
Len Brown authored
[ Upstream commit 1f81c5ef ] Some Chromebook BIOS' do not export an ACPI LPIT, which is how Linux finds the residency counter for CPU and SYSTEM low power states, that is exports in /sys/devices/system/cpu/cpuidle/*residency_us When these sysfs attributes are missing, check the debugfs attrubte from the pmc_core driver, which accesses the same counter value. Signed-off-by:
Len Brown <len.brown@intel.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Len Brown authored
[ Upstream commit d8d005ba ] Warning: ‘__builtin_strncpy’ specified bound 20 equals destination size [-Wstringop-truncation] reduce param to strncpy, to guarantee that a null byte is always copied into destination buffer. Signed-off-by:
-
James Zhu authored
[ Upstream commit acfc62dc ] fix typo for vcn1 idle check Signed-off-by:
James Zhu <James.Zhu@amd.com> Reviewed-by:
Leo Liu <leo.liu@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Eugeniy Paltsev authored
[ Upstream commit 785d74ec ] Even though INITRAMFS_SOURCE kconfig option isn't set in most of defconfigs it is used (set) extensively by various build systems. Commit f26661e1 ("initramfs: make initramfs compression choice non-optional") has changed default compression mode. Previously we compress initramfs using available compression algorithm. Now we don't use any compression at all by default. It significantly increases the image size in case of build system chooses embedded initramfs. Initially I faced with this issue while using buildroot. As of today it's not possible to set preferred compression mode in target defconfig as this option depends on INITRAMFS_SOURCE being set. Modification of all build systems either doesn't look like good option. Let's instead rewrite initramfs compression mode choices list the way that "INITRAMFS_COMPRESSION_NONE" will be the last option in the list. In that case it will be chosen only if all other options (which implements any compression) are not available. Signed-off-by:
Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Gerd Hoffmann authored
[ Upstream commit 8c34cd1a ] Shutdown of firmware framebuffer has a bunch of problems. Because of this the framebuffer region might still be reserved even after drm_fb_helper_remove_conflicting_pci_framebuffers() returned. Don't consider pci_request_region() failure for the framebuffer region as fatal error to workaround this issue. Reported-by:
Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Acked-by:
Sam Ravnborg <sam@ravnborg.org> Link: http://patchwork.freedesktop.org/patch/msgid/20200313084152.2734-1-kraxel@redhat.comSigned-off-by:
-
Mario Kleiner authored
[ Upstream commit dec9de2a ] This fixes a problem found on the MacBookPro 2017 Retina panel: The panel reports 10 bpc color depth in its EDID, and the firmware chooses link settings at boot which support enough bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2 aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports 2.7 Gbps (multiplier value 0xa) as possible, in direct contradiction of what the firmware successfully set up. This restricts the panel to 8 bpc, not providing the full color depth of the panel on Linux <= 5.5. Additionally, commit '4a8ca46b ("drm/amd/display: Default max bpc to 16 for eDP")' introduced into Linux 5.6-rc1 will unclamp panel depth to its full 10 bpc, thereby requiring a eDP bandwidth for all modes that exceeds the bandwidth available and causes all modes to fail validation -> No modes for the laptop panel -> failure to set any mode -> Panel goes dark. This patch adds a quirk specific to the MBP 2017 15" Retina panel to override reported max link rate to the correct maximum of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display precision. Please apply for Linux 5.6+ to avoid regressing Apple MBP panel support. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by:
-
Prabhath Sajeepa authored
[ Upstream commit 9134ae2a ] The timeout of identify cmd, which is invoked as part of admin queue creation, can result in freeing of async event data both in nvme_rdma_timeout handler and error handling path of nvme_rdma_configure_admin queue thus causing NULL pointer reference. Call Trace: ? nvme_rdma_setup_ctrl+0x223/0x800 [nvme_rdma] nvme_rdma_create_ctrl+0x2ba/0x3f7 [nvme_rdma] nvmf_dev_write+0xa54/0xcc6 [nvme_fabrics] __vfs_write+0x1b/0x40 vfs_write+0xb2/0x1b0 ksys_write+0x61/0xd0 __x64_sys_write+0x1a/0x20 do_syscall_64+0x60/0x1e0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reviewed-by:
Roland Dreier <roland@purestorage.com> Reviewed-by:
Max Gurtovoy <maxg@mellanox.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Prabhath Sajeepa <psajeepa@purestorage.com> Signed-off-by:
Keith Busch <kbusch@kernel.org> Signed-off-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit 582eea23 ] Under certain circumstances, depending on the order of addresses on the interfaces, it could be that sctp_v[46]_get_dst() would return a dst with a mismatched struct flowi. For example, if when walking through the bind addresses and the first one is not a match, it saves the dst as a fallback (added in 410f0383), but not the flowi. Then if the next one is also not a match, the previous dst will be returned but with the flowi information for the 2nd address, which is wrong. The fix is to use a locally stored flowi that can be used for such attempts, and copy it to the parameter only in case it is a possible match, together with the corresponding dst entry. The patch updates IPv6 code mostly just to be in sync. Even though the issue is also present there, it fallback is not expected to work with IPv6. Fixes: 410f0383 ("sctp: add routing output fallback") Reported-by:
Jin Meng <meng.a.jin@nokia-sbell.com> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Tested-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Qiujun Huang authored
[ Upstream commit 5c3e82fe ] We should iterate over the datamsgs to move all chunks(skbs) to newsk. The following case cause the bug: for the trouble SKB, it was in outq->transmitted list sctp_outq_sack sctp_check_transmitted SKB was moved to outq->sacked list then throw away the sack queue SKB was deleted from outq->sacked (but it was held by datamsg at sctp_datamsg_to_asoc So, sctp_wfree was not called here) then migrate happened sctp_for_each_tx_datachunk( sctp_clear_owner_w); sctp_assoc_migrate(); sctp_for_each_tx_datachunk( sctp_set_owner_w); SKB was not in the outq, and was not changed to newsk finally __sctp_outq_teardown sctp_chunk_put (for another skb) sctp_datamsg_put __kfree_skb(msg->frag_list) sctp_wfree (for SKB) SKB->sk was still oldsk (skb->sk != asoc->base.sk). Reported-and-tested-by: syzbot+cea71eec5d6de256d54d@syzkaller.appspotmail.com Signed-off-by:
Qiujun Huang <hqjagain@gmail.com> Acked-by:
Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by:
-
William Dauchy authored
[ Upstream commit 25629fda ] when creating a new ipip interface with no local/remote configuration, the lookup is done with TUNNEL_NO_KEY flag, making it impossible to match the new interface (only possible match being fallback or metada case interface); e.g: `ip link add tunl1 type ipip dev eth0` To fix this case, adding a flag check before the key comparison so we permit to match an interface with no local/remote config; it also avoids breaking possible userland tools relying on TUNNEL_NO_KEY flag and uninitialised key. context being on my side, I'm creating an extra ipip interface attached to the physical one, and moving it to a dedicated namespace. Fixes: c5441932 ("GRE: Refactor GRE tunneling code.") Signed-off-by:
William Dauchy <w.dauchy@criteo.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Qian Cai authored
[ Upstream commit fbe4e0c1 ] fib_triestat_seq_show() calls hlist_for_each_entry_rcu(tb, head, tb_hlist) without rcu_read_lock() will trigger a warning, net/ipv4/fib_trie.c:2579 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by proc01/115277: #0: c0000014507acf00 (&p->lock){+.+.}-{3:3}, at: seq_read+0x58/0x670 Call Trace: dump_stack+0xf4/0x164 (unreliable) lockdep_rcu_suspicious+0x140/0x164 fib_triestat_seq_show+0x750/0x880 seq_read+0x1a0/0x670 proc_reg_read+0x10c/0x1b0 __vfs_read+0x3c/0x70 vfs_read+0xac/0x170 ksys_read+0x7c/0x140 system_call+0x5c/0x68 Fix it by adding a pair of rcu_read_lock/unlock() and use cond_resched_rcu() to avoid the situation where walking of a large number of items may prevent scheduling for a long time. Signed-off-by:
Qian Cai <cai@lca.pw> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
- 02 Apr, 2020 6 commits
-
-
Greg Kroah-Hartman authored
-
Madalin Bucur authored
commit d79e9d7c upstream. The correct setting for the RGMII ports on LS1046ARDB is to enable delay on both Rx and Tx so the interface mode used must be PHY_INTERFACE_MODE_RGMII_ID. Since commit 1b3047b5 ("net: phy: realtek: add support for configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver has control over the RGMII RX delay and it is disabling it for RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but in the device tree the mode was described as "rgmii". Changing the phy-connection-type to "rgmii-id" to address the issue. Fixes: 3fa395d2 ("arm64: dts: add LS1046A DPAA FMan nodes") Signed-off-by:
Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by:
-
Madalin Bucur authored
commit 4022d808 upstream. The correct setting for the RGMII ports on LS1043ARDB is to enable delay on both Rx and Tx so the interface mode used must be PHY_INTERFACE_MODE_RGMII_ID. Since commit 1b3047b5 ("net: phy: realtek: add support for configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver has control over the RGMII RX delay and it is disabling it for RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but in the device tree the mode was described as "rgmii_txid". This issue was not apparent at the time as the PHY driver took the same action for RGMII_TXID and RGMII_ID back then but it became visible (RX no longer working) after the above patch. Changing the phy-connection-type to "rgmii-id" to address the issue. Fixes: bf02f2ff ("arm64: dts: add LS1043A DPAA FMan support") Signed-off-by:
-
Arthur Demchenkov authored
commit 0c5220a3 upstream. Commit a758f50f ("mtd: onenand: omap2: Configure driver from DT") started using DT specified timings for GPMC, and as a result the OneNAND stopped working on N900 as we had wrong values in the DT. Fix by updating the values to bootloader timings that have been tested to be working on Nokia N900 with OneNAND manufacturers: Samsung, Numonyx. Fixes: a758f50f ("mtd: onenand: omap2: Configure driver from DT") Signed-off-by:
Arthur Demchenkov <spinal.by@gmail.com> Tested-by:
Merlijn Wajer <merlijn@wizzup.org> Reviewed-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Marco Felsch authored
commit 636b45b8 upstream. The current set minimum voltage of 730000µV seems to be wrong. I don't know the document which specifies that but the imx6qdl datasheets says that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed, lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp). Fixes: ddec5d1c ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM") Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Nick Hudson authored
commit 6687c201 upstream. Define the sdhci pinctrl state as "default" so it gets applied correctly and to match all other RPis. Fixes: 2c7c040c ("ARM: dts: bcm2835: Add Raspberry Pi Zero W") Signed-off-by:
Nick Hudson <skrll@netbsd.org> Signed-off-by:
-
