- 29 Apr, 2022 1 commit
-
-
Andrii Nakryiko authored
Detect CO-RE spec truncation and append "..." to make user aware that there was supposed to be more of the spec there. Signed-off-by:
Andrii Nakryiko <andrii@kernel.org> Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20220428041523.4089853-2-andrii@kernel.org
-
- 28 Apr, 2022 10 commits
-
-
Andrii Nakryiko authored
Add new or modify existing SEC() definitions to be target-less and validate that libbpf handles such program definitions correctly. For kprobe/kretprobe we also add explicit test that generic bpf_program__attach() works in cases when kprobe definition contains proper target. It wasn't previously tested as selftests code always explicitly specified the target regardless. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20220428185349.3799599-4-andrii@kernel.org
-
Andrii Nakryiko authored
Similar to previous patch, support target-less definitions like SEC("fentry"), SEC("freplace"), etc. For such BTF-backed program types it is expected that user will specify BTF target programmatically at runtime using bpf_program__set_attach_target() *before* load phase. If not, libbpf will report this as an error. Aslo use SEC_ATTACH_BTF flag instead of explicitly listing a set of types that are expected to require attach_btf_id. This was an accidental omission during custom SEC() support refactoring. Signed-off-by: -
Andrii Nakryiko authored
In a lot of cases the target of kprobe/kretprobe, tracepoint, raw tracepoint, etc BPF program might not be known at the compilation time and will be discovered at runtime. This was always a supported case by libbpf, with APIs like bpf_program__attach_{kprobe,tracepoint,etc}() accepting full target definition, regardless of what was defined in SEC() definition in BPF source code. Unfortunately, up till now libbpf still enforced users to specify at least something for the fake target, e.g., SEC("kprobe/whatever"), which is cumbersome and somewhat misleading. This patch allows target-less SEC() definitions for basic tracing BPF program types: - kprobe/kretprobe; - multi-kprobe/multi-kretprobe; - tracepoints; - raw tracepoints. Such target-less SEC() definitions are meant to specify declaratively proper BPF program type only. Attachment of them will have to be handled programmatically using correct APIs. As such, skeleton's auto-attachment of such BPF programs is skipped and generic bpf_program__attach() will fail, if attempted, due to the lack of enough target information. Signed-off-by: -
Liu Jian authored
The skb_to_sgvec fails only when the number of frag_list and frags exceeds MAX_MSG_FRAGS. Therefore, we can call skb_linearize only when the conversion fails. Signed-off-by:
Liu Jian <liujian56@huawei.com> Signed-off-by:
John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20220427115150.210213-1-liujian56@huawei.com
-
Tiezhu Yang authored
"respetively" should be "respectively". Signed-off-by:
Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by:
-
Tiezhu Yang authored
According to include/uapi/linux/bpf.h: #define BPF_FROM_LE BPF_TO_LE #define BPF_FROM_BE BPF_TO_BE BPF_FROM_BE exists as alias for BPF_TO_BE instead of BPF_TO_LE. Signed-off-by:
-
Tiezhu Yang authored
The word "instructions" is duplicated, remove it. Signed-off-by:
-
Zhengchao Shao authored
When xdp_rxq_info_user program exits unexpectedly, it doesn't detach xdp prog of device, and other xdp prog can't be attached to the device. So call init_exit() to detach xdp prog when program exits unexpectedly. Signed-off-by:
Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by:
-
Mykola Lysenko authored
Implement per subtest log collection for both parallel and sequential test execution. This allows granular per-subtest error output in the 'All error logs' section. Add subtest log transfer into the protocol during the parallel test execution. Move all test log printing logic into dump_test_log function. One exception is the output of test names when verbose printing is enabled. Move test name/result printing into separate functions to avoid repetition. Print all successful subtest results in the log. Print only failed test logs when test does not have subtests. Or only failed subtests' logs when test has subtests. Disable 'All error logs' output when verbose mode is enabled. This functionality was already broken and is causing confusion. Signed-off-by:
Mykola Lysenko <mykolal@fb.com> Signed-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf-next 2022-04-27 We've added 85 non-merge commits during the last 18 day(s) which contain a total of 163 files changed, 4499 insertions(+), 1521 deletions(-). The main changes are: 1) Teach libbpf to enhance BPF verifier log with human-readable and relevant information about failed CO-RE relocations, from Andrii Nakryiko. 2) Add typed pointer support in BPF maps and enable it for unreferenced pointers (via probe read) and referenced ones that can be passed to in-kernel helpers, from Kumar Kartikeya Dwivedi. 3) Improve xsk to break NAPI loop when rx queue gets full to allow for forward progress to consume descriptors, from Maciej Fijalkowski & Björn Töpel. 4) Fix a small RCU read-side race in BPF_PROG_RUN routines which dereferenced the effective prog array before the rcu_read_lock, from Stanislav Fomichev. 5) Implement BPF atomic operations for RV64 JIT, and add libbpf parsing logic for USDT arguments under riscv{32,64}, from Pu Lehui. 6) Implement libbpf parsing of USDT arguments under aarch64, from Alan Maguire. 7) Enable bpftool build for musl and remove nftw with FTW_ACTIONRETVAL usage so it can be shipped under Alpine which is musl-based, from Dominique Martinet. 8) Clean up {sk,task,inode} local storage trace RCU handling as they do not need to use call_rcu_tasks_trace() barrier, from KP Singh. 9) Improve libbpf API documentation and fix error return handling of various API functions, from Grant Seltzer. 10) Enlarge offset check for bpf_skb_{load,store}_bytes() helpers given data length of frags + frag_list may surpass old offset limit, from Liu Jian. 11) Various improvements to prog_tests in area of logging, test execution and by-name subtest selection, from Mykola Lysenko. 12) Simplify map_btf_id generation for all map types by moving this process to build time with help of resolve_btfids infra, from Menglong Dong. 13) Fix a libbpf bug in probing when falling back to legacy bpf_probe_read*() helpers; the probing caused always to use old helpers, from Runqing Yang. 14) Add support for ARCompact and ARCv2 platforms for libbpf's PT_REGS tracing macros, from Vladimir Isaev. 15) Cleanup BPF selftests to remove old & unneeded rlimit code given kernel switched to memcg-based memory accouting a while ago, from Yafang Shao. 16) Refactor of BPF sysctl handlers to move them to BPF core, from Yan Zhu. 17) Fix BPF selftests in two occasions to work around regressions caused by latest LLVM to unblock CI until their fixes are worked out, from Yonghong Song. 18) Misc cleanups all over the place, from various others. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (85 commits) selftests/bpf: Add libbpf's log fixup logic selftests libbpf: Fix up verifier log for unguarded failed CO-RE relos libbpf: Simplify bpf_core_parse_spec() signature libbpf: Refactor CO-RE relo human description formatting routine libbpf: Record subprog-resolved CO-RE relocations unconditionally selftests/bpf: Add CO-RE relos and SEC("?...") to linked_funcs selftests libbpf: Avoid joining .BTF.ext data with BPF programs by section name libbpf: Fix logic for finding matching program for CO-RE relocation libbpf: Drop unhelpful "program too large" guess libbpf: Fix anonymous type check in CO-RE logic bpf: Compute map_btf_id during build time selftests/bpf: Add test for strict BTF type check selftests/bpf: Add verifier tests for kptr selftests/bpf: Add C tests for kptr libbpf: Add kptr type tag macros to bpf_helpers.h bpf: Make BTF type match stricter for release arguments bpf: Teach verifier about kptr_get kfunc helpers bpf: Wire up freeing of referenced kptr bpf: Populate pairs of btf_id and destructor kfunc in btf bpf: Adapt copy_map_value for multiple offset case ... ==================== Link: https://lore.kernel.org/r/20220427224758.20976-1-daniel@iogearbox.netSigned-off-by:Jakub Kicinski <kuba@kernel.org>
-
- 27 Apr, 2022 28 commits
-
-
Arun Ramadoss authored
The mib counters for the ksz9477 is same for the ksz9477 switch and LAN937x switch. Hence moving it to ksz_common.c file in order to have it generic function. The DSA hook get_stats64 now can call ksz_get_stats64. Signed-off-by:
Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20220426091048.9311-1-arun.ramadoss@microchip.comSigned-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== net: remove non-Ethernet drivers using virt_to_bus() Networking is currently the main offender in using virt_to_bus(). Frankly all the drivers which use it are super old and unlikely to be used today. They are just an ongoing maintenance burden. In other words this series is using virt_to_bus() as an excuse to shed some old stuff. Having done the tree-wide dev_addr_set() conversion recently I have limited sympathy for carrying dead code. Obviously please scream if any of these drivers _is_ in fact still being used. Otherwise let's take the chance, we can always apologize and revert if users show up later. Also I should say thanks to everyone who contributed to this code! The work continues to be appreciated although realistically in more of a "history book" fashion... ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Another incarnation of Z8530, looks like? Again, no real changes in the git history, and it needs VIRT_TO_BUS. Unlikely to have users, let's spend less time refactoring dead code... Signed-off-by:
-
Jakub Kicinski authored
Looks like all the changes to this driver had been automated churn since git era begun. The driver is using virt_to_bus(), it's just a maintenance burden unlikely to have any users. Signed-off-by:
-
Jakub Kicinski authored
Looks like all the changes to this driver had been automated churn since git era begun. The driver is using virt_to_bus() so it should be updated to a proper DMA API or removed. Given the latest "news" entry on the website is from 1999 I'm opting for the latter. I'm marking the allocated char device major number as [REMOVED], I reckon we can't reuse it in case some SW out there assumes its COSA? Signed-off-by:
-
Jakub Kicinski authored
This driver received nothing but automated fixes in the last 15 years. Since it's using virt_to_bus it's unlikely to be used on any modern platform. Signed-off-by:
-
Jakub Kicinski authored
This driver received nothing but automated fixes since git era begun. Since it's using virt_to_bus it's unlikely to be used on any modern platform. Signed-off-by:
-
Jakub Kicinski authored
This driver received nothing but automated fixes (mostly spelling and compiler warnings) since git era begun. Since it's using virt_to_bus it's unlikely to be used on any modern platform. Signed-off-by:
-
David S. Miller authored
Horatiu Vultur says: ==================== net: lan966x: Add support for PTP programmable pins Lan966x has 8 PTP programmable pins. The last pin is hardcoded to be used by PHC0 and all the rest are shareable between the PHCs. The PTP pins can implement both extts and perout functions. v1->v2: - use ptp_find_pin_unlocked instead of ptp_find_pin inside the irq handler. ==================== Signed-off-by: -
Horatiu Vultur authored
Extend the PTP programmable pins to implement also PTP_PF_EXTTS function. The PTP pin can be configured to capture only on the rising edge of the PPS signal. And once an event is seen then an interrupt is generated and the local time counter is saved. The interrupt is shared between all the pins. Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Horatiu Vultur authored
Lan966x has 8 PTP programmable pins, where the last pins is hardcoded to be used by PHC0, which does the frame timestamping. All the rest of the PTP pins can be shared between the PHCs and can have different functions like perout or extts. For now add support for PTP_FS_PEROUT. The HW is not able to support absolute start time but can use the nsec for phase adjustment when generating PPS. Signed-off-by:
-
Horatiu Vultur authored
Add registers that are used to configure the PTP pins. These registers are used to enable the interrupts per PTP pin and to set the waveform generated by the pin. Signed-off-by:
-
Horatiu Vultur authored
To read/write a value to a PHC, it is required to use a PTP pin. Currently it is used pin 5, but change to pin 7 as is the last pin. All the other pins will have different functions. Signed-off-by:
-
Horatiu Vultur authored
Extend dt-bindings for lan966x with ptp external interrupt. This is generated when an external 1pps signal is received on the ptp pin. Signed-off-by:
-
David S. Miller authored
Mat Martineau says: ==================== mptcp: Timeout for MP_FAIL response When one peer sends an infinite mapping to coordinate fallback from MPTCP to regular TCP, the other peer is expected to send a packet with the MPTCP MP_FAIL option to acknowledge the infinite mapping. Rather than leave the connection in some half-fallback state, this series adds a timeout after which the infinite mapping sender will reset the connection. Patch 1 adds a fallback self test. Patches 2-5 make use of the MPTCP socket's retransmit timer to reset the MPTCP connection if no MP_FAIL was received. Patches 6 and 7 extends the self test to check MP_FAIL-related MIBs. ==================== Signed-off-by: -
Geliang Tang authored
When the multiple checksum errors occur in chk_csum_nr(), print the numbers of the errors as an extra message. Signed-off-by:
Geliang Tang <geliang.tang@suse.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Geliang Tang authored
This patch extends chk_fail_nr to check the MP_FAIL response mibs. Add a new argument invert for chk_fail_nr to allow it can check the MP_FAIL TX and RX mibs from the opposite direction. When the infinite map is received before the MP_FAIL response, the response will be lost. A '-' can be added into fail_tx or fail_rx to represent that MP_FAIL response TX or RX can be lost when doing the checks. Signed-off-by:
-
Geliang Tang authored
This patch adds a new msk->flags bit MPTCP_FAIL_NO_RESPONSE, then reuses sk_timer to trigger a check if we have not received a response from the peer after sending MP_FAIL. If the peer doesn't respond properly, reset the subflow. Signed-off-by:
-
Geliang Tang authored
This patch adds a new struct member mp_fail_response_expect in struct mptcp_subflow_context to support MP_FAIL response. In the single subflow with checksum error and contiguous data special case, a MP_FAIL is sent in response to another MP_FAIL. Signed-off-by:
-
Geliang Tang authored
mptcp_data_lock() needs to be held when manipulating the msk retransmit_timer or the sk sk_timer. This patch adds the data lock for the both timers. Signed-off-by:
-
Geliang Tang authored
Use the helper mptcp_stop_timer() instead of using sk_stop_timer() to stop icsk_retransmit_timer directly. Signed-off-by:
-
Geliang Tang authored
Add the single subflow test case for MP_FAIL, to test the infinite mapping case. Use the test_linkfail value to make 128KB test files. Add a new function reset_with_fail(), in it use 'iptables' and 'tc action pedit' rules to produce the bit flips to trigger the checksum failures. Set validate_checksum to enable checksums for the MP_FAIL tests without passing the '-C' argument. Set check_invert flag to enable the invert bytes check for the output data in check_transfer(). Instead of the file mismatch error, this test prints out the inverted bytes. Add a new function pedit_action_pkts() to get the numbers of the packets edited by the tc pedit actions. Print this numbers to the output. Also add the needed kernel configures in the selftests config file. Suggested-by:
Davide Caratti <dcaratti@redhat.com> Co-developed-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
-
Marcel Ziswiler authored
Fix spelling in comment. Fixes: 94abdad6 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip") Signed-off-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Link: https://lore.kernel.org/r/20220425154856.169499-1-marcel@ziswiler.comSigned-off-by:
-
Bjorn Helgaas authored
The only remaining definitions of __SLOW_DOWN_IO (for alpha and ia64) do nothing, and the only mentions in networking are in comments. Remove these mentions. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Bjorn Helgaas authored
atp.h is included only by atp.c, which does not use eeprom_delay(). Remove the unused definition. Signed-off-by:
-
Jakub Kicinski authored
When NIC takes care of crypto (or the record has already been decrypted) we forget to update darg->async. ->async is supposed to mean whether record is async capable on input and whether record has been queued for async crypto on output. Reported-by:
Gal Pressman <gal@nvidia.com> Fixes: 3547a1f9 ("tls: rx: use async as an in-out argument") Tested-by:
-
Russell King (Oracle) authored
Daniel Golle reports that the conversion of mt753x to phylink PCS caused an oops as below. The problem is with the placement of the PCS initialisation, which occurs after mt7531_setup() has been called. However, burited in this function is a call to setup the CPU port, which requires the PCS structure to be already setup. Fix this by changing the initialisation order. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020 Mem abort info: ESR = 0x96000005 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x05: level 1 translation fault Data abort info: ISV = 0, ISS = 0x00000005 CM = 0, WnR = 0 user pgtable: 4k pages, 39-bit VAs, pgdp=0000000046057000 [0000000000000020] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 Internal error: Oops: 96000005 [#1] SMP Modules linked in: CPU: 0 PID: 32 Comm: kworker/u4:1 Tainted: G S 5.18.0-rc3-next-20220422+ #0 Hardware name: Bananapi BPI-R64 (DT) Workqueue: events_unbound deferred_probe_work_func pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : mt7531_cpu_port_config+0xcc/0x1b0 lr : mt7531_cpu_port_config+0xc0/0x1b0 sp : ffffffc008d5b980 x29: ffffffc008d5b990 x28: ffffff80060562c8 x27: 00000000f805633b x26: ffffff80001a8880 x25: 00000000000009c4 x24: 0000000000000016 x23: ffffff8005eb6470 x22: 0000000000003600 x21: ffffff8006948080 x20: 0000000000000000 x19: 0000000000000006 x18: 0000000000000000 x17: 0000000000000001 x16: 0000000000000001 x15: 02963607fcee069e x14: 0000000000000000 x13: 0000000000000030 x12: 0101010101010101 x11: ffffffc037302000 x10: 0000000000000870 x9 : ffffffc008d5b800 x8 : ffffff800028f950 x7 : 0000000000000001 x6 : 00000000662b3000 x5 : 00000000000002f0 x4 : 0000000000000000 x3 : ffffff800028f080 x2 : 0000000000000000 x1 : ffffff800028f080 x0 : 0000000000000000 Call trace: mt7531_cpu_port_config+0xcc/0x1b0 mt753x_cpu_port_enable+0x24/0x1f0 mt7531_setup+0x49c/0x5c0 mt753x_setup+0x20/0x31c dsa_register_switch+0x8bc/0x1020 mt7530_probe+0x118/0x200 mdio_probe+0x30/0x64 really_probe.part.0+0x98/0x280 __driver_probe_device+0x94/0x140 driver_probe_device+0x40/0x114 __device_attach_driver+0xb0/0x10c bus_for_each_drv+0x64/0xa0 __device_attach+0xa8/0x16c device_initial_probe+0x10/0x20 bus_probe_device+0x94/0x9c deferred_probe_work_func+0x80/0xb4 process_one_work+0x200/0x3a0 worker_thread+0x260/0x4c0 kthread+0xd4/0xe0 ret_from_fork+0x10/0x20 Code: 9409e911 937b7e60 8b0002a0 f9405800 (f9401005) ---[ end trace 0000000000000000 ]--- Reported-by:
Daniel Golle <daniel@makrotopia.org> Tested-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by:
-
Eric Dumazet authored
Logic added in commit f35f8219 ("tcp: defer skb freeing after socket lock is released") helped bulk TCP flows to move the cost of skbs frees outside of critical section where socket lock was held. But for RPC traffic, or hosts with RFS enabled, the solution is far from being ideal. For RPC traffic, recvmsg() has to return to user space right after skb payload has been consumed, meaning that BH handler has no chance to pick the skb before recvmsg() thread. This issue is more visible with BIG TCP, as more RPC fit one skb. For RFS, even if BH handler picks the skbs, they are still picked from the cpu on which user thread is running. Ideally, it is better to free the skbs (and associated page frags) on the cpu that originally allocated them. This patch removes the per socket anchor (sk->defer_list) and instead uses a per-cpu list, which will hold more skbs per round. This new per-cpu list is drained at the end of net_action_rx(), after incoming packets have been processed, to lower latencies. In normal conditions, skbs are added to the per-cpu list with no further action. In the (unlikely) cases where the cpu does not run net_action_rx() handler fast enough, we use an IPI to raise NET_RX_SOFTIRQ on the remote cpu. Also, we do not bother draining the per-cpu list from dev_cpu_dead() This is because skbs in this list have no requirement on how fast they should be freed. Note that we can add in the future a small per-cpu cache if we see any contention on sd->defer_lock. Tested on a pair of hosts with 100Gbit NIC, RFS enabled, and /proc/sys/net/ipv4/tcp_rmem[2] tuned to 16MB to work around page recycling strategy used by NIC driver (its page pool capacity being too small compared to number of skbs/pages held in sockets receive queues) Note that this tuning was only done to demonstrate worse conditions for skb freeing for this particular test. These conditions can happen in more general production workload. 10 runs of one TCP_STREAM flow Before: Average throughput: 49685 Mbit. Kernel profiles on cpu running user thread recvmsg() show high cost for skb freeing related functions (*) 57.81% [kernel] [k] copy_user_enhanced_fast_string (*) 12.87% [kernel] [k] skb_release_data (*) 4.25% [kernel] [k] __free_one_page (*) 3.57% [kernel] [k] __list_del_entry_valid 1.85% [kernel] [k] __netif_receive_skb_core 1.60% [kernel] [k] __skb_datagram_iter (*) 1.59% [kernel] [k] free_unref_page_commit (*) 1.16% [kernel] [k] __slab_free 1.16% [kernel] [k] _copy_to_iter (*) 1.01% [kernel] [k] kfree (*) 0.88% [kernel] [k] free_unref_page 0.57% [kernel] [k] ip6_rcv_core 0.55% [kernel] [k] ip6t_do_table 0.54% [kernel] [k] flush_smp_call_function_queue (*) 0.54% [kernel] [k] free_pcppages_bulk 0.51% [kernel] [k] llist_reverse_order 0.38% [kernel] [k] process_backlog (*) 0.38% [kernel] [k] free_pcp_prepare 0.37% [kernel] [k] tcp_recvmsg_locked (*) 0.37% [kernel] [k] __list_add_valid 0.34% [kernel] [k] sock_rfree 0.34% [kernel] [k] _raw_spin_lock_irq (*) 0.33% [kernel] [k] __page_cache_release 0.33% [kernel] [k] tcp_v6_rcv (*) 0.33% [kernel] [k] __put_page (*) 0.29% [kernel] [k] __mod_zone_page_state 0.27% [kernel] [k] _raw_spin_lock After patch: Average throughput: 73076 Mbit. Kernel profiles on cpu running user thread recvmsg() looks better: 81.35% [kernel] [k] copy_user_enhanced_fast_string 1.95% [kernel] [k] _copy_to_iter 1.95% [kernel] [k] __skb_datagram_iter 1.27% [kernel] [k] __netif_receive_skb_core 1.03% [kernel] [k] ip6t_do_table 0.60% [kernel] [k] sock_rfree 0.50% [kernel] [k] tcp_v6_rcv 0.47% [kernel] [k] ip6_rcv_core 0.45% [kernel] [k] read_tsc 0.44% [kernel] [k] _raw_spin_lock_irqsave 0.37% [kernel] [k] _raw_spin_lock 0.37% [kernel] [k] native_irq_return_iret 0.33% [kernel] [k] __inet6_lookup_established 0.31% [kernel] [k] ip6_protocol_deliver_rcu 0.29% [kernel] [k] tcp_rcv_established 0.29% [kernel] [k] llist_reverse_order v2: kdoc issue (kernel bots) do not defer if (alloc_cpu == smp_processor_id()) (Paolo) replace the sk_buff_head with a single-linked list (Jakub) add a READ_ONCE()/WRITE_ONCE() for the lockless read of sd->defer_list Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20220422201237.416238-1-eric.dumazet@gmail.comSigned-off-by:
-
- 26 Apr, 2022 1 commit
-
-
Alexei Starovoitov authored
Andrii Nakryiko says: ==================== This patch set teaches libbpf to enhance BPF verifier log with human-readable and relevant information about failed CO-RE relocation. Patch #9 is the main one with the new logic. See relevant commit messages for some more details. All the other patches are either fixing various bugs detected while working on this feature, most prominently a bug with libbpf not handling CO-RE relocations for SEC("?...") programs, or are refactoring libbpf internals to allow for easier reuse of CO-RE relo lookup and formatting logic. ==================== Signed-off-by:
-
