- 22 Apr, 2019 40 commits
-
-
Neil Armstrong authored
The Amlogic G12A SoC embeds a second CEC controller with a totally different design. The two controller can work in the same time since the CEC line can be set to two different pins on the two controllers. This second CEC controller is documented as "AO-CEC-B", thus the registers will be named "CECB_" to differentiate with the other AO-CEC driver. Unlike the other AO-CEC controller, this one takes the Oscillator clock as input and embeds a dual-divider to provide a precise 32768Hz clock for communication. This is handled by registering a clock in the driver. Unlike the other AO-CEC controller, this controller supports setting up to 15 logical addresses and supports the signal_free_time settings in the transmit function. Unfortunately, this controller does not support "monitor" mode. Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Neil Armstrong authored
The Amlogic G12A embeds a second CEC controller named AO-CEC-B, and the other one is AO-CEC-A described by the current bindings. The register interface is very close but the internal architecture is totally different. The other difference is the clock source, the AO-CEC-B takes the "oscin", the Always-On Oscillator clock, as input and embeds a dual-divider clock divider to provide the precise 32768Hz base clock for CEC communication. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Hans Verkuil authored
The CrosEC CEC driver never decremented the HDMI device refcount. CEC drivers only need the HDMI device pointer as a key in the notifier list, it never accesses the device, so there is no need to keep a reference. Signed-off-by:
-
Hans Verkuil authored
The SECO CEC driver never decremented the HDMI device refcount. CEC drivers only need the HDMI device pointer as a key in the notifier list, it never accesses the device, so there is no need to keep a reference. Signed-off-by:
-
Hans Verkuil authored
The Tegra CEC driver increased the HDMI device refcount when it shouldn't. Use the new helper function to ensure that that doesn't happen and to simplify the driver code. Signed-off-by:
-
Hans Verkuil authored
The STI CEC driver increased the HDMI device refcount when it shouldn't. Use the new helper function to ensure that that doesn't happen and to simplify the driver code. Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by:
-
Hans Verkuil authored
The S5P CEC driver increased the HDMI device refcount when it shouldn't. Use the new helper function to ensure that that doesn't happen and to simplify the driver code. Signed-off-by:
-
Hans Verkuil authored
The meson CEC driver increased the HDMI device refcount when it shouldn't. Use the new helper function to ensure that that doesn't happen and to simplify the driver code. Signed-off-by:
-
Hans Verkuil authored
Add helper function to parse the DT for the hdmi-phandle property and return the corresponding struct device pointer. It takes care to avoid increasing the device refcount since all we need is the device pointer. This pointer is used in the notifier list as a key, but it is never accessed by the CEC driver. Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Acked-by:
-
Arnd Bergmann authored
I previously added an RC_CORE dependency here, but missed the corner case of CONFIG_VIDEO_SECO_CEC=y with CONFIG_RC_CORE=m, which still causes a link error: drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_probe': seco-cec.c:(.text+0x1b8): undefined reference to `devm_rc_allocate_device' seco-cec.c:(.text+0x2e8): undefined reference to `devm_rc_register_device' drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_irq_handler': seco-cec.c:(.text+0xa2c): undefined reference to `rc_keydown' Refine the dependency to disallow building the RC subdriver in this case. This is the same logic we apply in other drivers like it. Fixes: f27dd0ad ("media: seco-cec: fix RC_CORE dependency") Cc: <stable@vger.kernel.org> # 5.1 Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Yizhuo authored
In function ts2020_set_tuner_rf(), local variable "utmp" could be uninitialized if function regmap_read() returns -EINVAL. However, this value is used in if statement and written to the register, which is potentially unsafe. Signed-off-by:
Yizhuo <yzhai003@ucr.edu> Signed-off-by:
-
YueHaibing authored
Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Matthias Reichl authored
The timestamps in ir-keytable -t output showed that the Xbox DVD IR dongle decodes scancodes every 64ms. The last scancode of a longer button press is decodes 64ms after the last-but-one which indicates the decoder doesn't use a timeout but decodes on the last edge of the signal. 267.042629: lirc protocol(unknown): scancode = 0xace 267.042665: event type EV_MSC(0x04): scancode = 0xace 267.042665: event type EV_KEY(0x01) key_down: KEY_1(0x0002) 267.042665: event type EV_SYN(0x00). 267.106625: lirc protocol(unknown): scancode = 0xace 267.106643: event type EV_MSC(0x04): scancode = 0xace 267.106643: event type EV_SYN(0x00). 267.170623: lirc protocol(unknown): scancode = 0xace 267.170638: event type EV_MSC(0x04): scancode = 0xace 267.170638: event type EV_SYN(0x00). 267.234621: lirc protocol(unknown): scancode = 0xace 267.234636: event type EV_MSC(0x04): scancode = 0xace 267.234636: event type EV_SYN(0x00). 267.298623: lirc protocol(unknown): scancode = 0xace 267.298638: event type EV_MSC(0x04): scancode = 0xace 267.298638: event type EV_SYN(0x00). 267.543345: event type EV_KEY(0x01) key_down: KEY_1(0x0002) 267.543345: event type EV_SYN(0x00). 267.570015: event type EV_KEY(0x01) key_up: KEY_1(0x0002) 267.570015: event type EV_SYN(0x00). Add a protocol with the repeat value and set the timeout in the driver to 10ms (to have a bit of headroom for delays) so the Xbox DVD remote performs more responsive. Signed-off-by:
Matthias Reichl <hias@horus.com> Acked-by:
Benjamin Valentin <benpicco@googlemail.com> Signed-off-by:
-
Niklas Söderlund authored
Later datasheet versions (rev 1.00) clarifies that the FLD register should be set after LINKCNT. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by:
Ulrich Hecht <uli+renesas@fpond.eu> Reviewed-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Niklas Söderlund authored
Latest information from hardware engineers reveals that H3 ES2 and ES3 behave differently when working with link speeds bellow 250 Mpbs. Add a SoC match for H3 ES2.* and use the correct startup sequence. Signed-off-by:
-
Niklas Söderlund authored
The latest datasheet (rev 1.50) updates the start procedure for V3M and E3. Update the driver to match these changes. Signed-off-by:
-
Niklas Söderlund authored
Later versions of the datasheet updates the reset procedure to more closely resemble the standby mode. Update the driver to enter and exit the standby mode instead of resetting the hardware before and after streaming is started and stopped. This replaces the software reset (SRST.SRST) control. While at it break out the full start and stop procedures from rcsi2_s_stream() into the existing helper functions. Signed-off-by:
-
Niklas Söderlund authored
The resets property will become mandatory to operate the device, list it as such. All device tree source files have always included the reset property so making it mandatory will not introduce any regressions. While at it improve the description for the clocks property. Signed-off-by:
-
Philipp Zabel authored
If VIDIOC_CREATE_BUFS is called with a sizeimage smaller than the queue sizeimage, fail with -EINVAL instead of correcting the size and continuing without error. This is required by v4l2-compliance. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
v4l2-compliance sets colorimetry on the output queue and then verifies that querying colorimetry on the capture queue returns the same configuration. For this to work, the encoder must allow setting context colorimetry parameters on the output queue. Signed-off-by:
-
Philipp Zabel authored
The stateful encoder API requires VIDIOC_ENUM_FRAMESIZES to be implemented. Allow enumeration of supported frame sizes for encoding. Signed-off-by:
-
Philipp Zabel authored
Return -ENOTTY when userspace tries to call VIDIOC_(TRY_)ENCODER_CMD on a decoder instance or VIDIOC_(TRY_)DECODER_CMD on an encoder instance. Signed-off-by:
-
Philipp Zabel authored
Add min number of buffers for capture (decoder) and output (encoder) controls, which are required by the stateful video decoder / encoder interface specification. Signed-off-by:
-
Philipp Zabel authored
The error return value is not written by some firmware codecs, such as MPEG-2 decode on CodaHx4. Clear the error return value before starting the picture run to avoid misinterpreting unrelated values returned by sequence initialization as error return value. Signed-off-by:
-
Philipp Zabel authored
Since levels are specified in terms of maximum values, there is no reason to filter out lower levels than the supported maximum. Signed-off-by:
-
Philipp Zabel authored
The chosen codec depends on the coded format, which is known as soon as the S_FMT call on the coded queue. This allows to use the codec in callbacks that may be called before start_streaming, such as buf_queue. Signed-off-by:
-
Hans Verkuil authored
Calling VIDIOC_DQBUF can release the core serialization lock pointed to by vb2_queue->lock if it has to wait for a new buffer to arrive. However, if userspace dup()ped the video device filehandle, then it is possible to read or call DQBUF from two filehandles at the same time. It is also possible to call REQBUFS from one filehandle while the other is waiting for a buffer. This will remove all the buffers and reallocate new ones. Removing all the buffers isn't the problem here (that's already handled correctly by DQBUF), but the reallocating part is: DQBUF isn't aware that the buffers have changed. This is fixed by setting a flag whenever the lock is released while waiting for a buffer to arrive. And checking the flag where needed so we can return -EBUSY. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Reported-by:
Syzbot <syzbot+4180ff9ca6810b06c1e9@syzkaller.appspotmail.com> Reviewed-by:
Tomasz Figa <tfiga@chromium.org> Signed-off-by:
-
Dan Carpenter authored
The ctrl_check_input() function is called from pvr2_ctrl_range_check(). It's supposed to validate user supplied input and return true or false depending on whether the input is valid or not. The problem is that negative shifts or shifts greater than 31 are undefined in C. In practice with GCC they result in shift wrapping so this function returns true for some inputs which are not valid and this could result in a buffer overflow: drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname() warn: uncapped user index 'names[val]' The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create() and the highest valid bit is BIT(4). Fixes: 7fb20fa3 ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability") Signed-off-by:Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Jernej Skrabec authored
Currently, MEDIA_IOC_G_TOPOLOGY ioctl on cedrus fails due to incorrect initialization order. Fix that by moving video_register_device() before v4l2_m2m_register_media_controller() and while at it, fix error path. Reported-by:
Jonas Karlman <jonas@kwiboo.se> Signed-off-by:
Jernej Skrabec <jernej.skrabec@siol.net> Acked-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
-
Alexander Potapenko authored
syzkaller reported crashes on kfree() called from vivid_vid_cap_s_selection(). This looks like a simple typo, as dev->bitmap_cap is allocated with vzalloc() throughout the file. Fixes: ef834f78 ("[media] vivid: add the video capture and output parts") Signed-off-by:
Alexander Potapenko <glider@google.com> Reported-by:
Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com> Signed-off-by:
-
Hans Verkuil authored
If a buffer is queued to a request, followed by an attempt to queue the same buffer again, then the second qbuf returns an error since the buffer is not in the DEQUEUED state anymore. However, before it gets to that check it executes the code under the 'if (!vb->prepared)' condition. This clears previously set data needed for request handling, and now querybuf will no longer report that this buffer is part of a request. Move the state check to before the 'if' and make sure to only do the state check when called from QBUF and if V4L2_BUF_FLAG_REQUEST_FD is set. Signed-off-by:
-
Maoguang Meng authored
Update referenced frame buffer's reference count when playing vp9 content which has show_existing_frame flag, and copy enough buffer data to current shown frame. Signed-off-by:
Maoguang Meng <maoguang.meng@mediatek.com> Signed-off-by:
-
Sakari Ailus authored
The driver used %d for formatting unsigned values. Use %u instead. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by:
Bingbu Cao <bingbu.cao@intel.com> Signed-off-by:
-
Bingbu Cao authored
Current ImgU driver processes and releases the parameter buffer immediately after queued from user. This does not align with other image buffers which are grouped in sets and used for the same frame. If user queues multiple parameter buffers continuously, only the last one will take effect. To make consistent buffers usage, this patch changes the parameter buffer handling and group parameter buffer with other image buffers for each frame. Each time driver will queue one more group of buffers when previous frame processed and buffers consumed by css. Signed-off-by:
Tianshu Qiu <tian.shu.qiu@intel.com> Signed-off-by:
-
Mickael Guene authored
This V4L2 subdev driver enables STMicroelectronics MIPID02 device. Signed-off-by:
Mickael Guene <mickael.guene@st.com> Signed-off-by:
-
Mickael Guene authored
This adds documentation of device tree for MIPID02 CSI-2 to PARALLEL bridge. Reviewed-by:
-
Mickael Guene authored
This patch adds MEDIA_BUS_FMT_BGR888_3X8 used by STM MIPID02 CSI-2 to PARALLEL bridge driver when input format is MEDIA_BUS_FMT_BGR888_1X24. Signed-off-by:
-
Akinobu Mita authored
Avoid returning with mutex locked. Fixes: fa8cb644 ("[media] ov2659: Don't depend on subdev API") Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Akinobu Mita authored
This driver returns an error if unsupported media bus pixel code is requested by VIDIOC_SUBDEV_S_FMT. But according to Documentation/media/uapi/v4l/vidioc-subdev-g-fmt.rst, Drivers must not return an error solely because the requested format doesn't match the device capabilities. They must instead modify the format to match what the hardware can provide. So select default format code and return success in that case. This is detected by v4l2-compliance. Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com> Signed-off-by:
-
Janusz Krzysztofik authored
Register V4L2 subdevice implemented by the driver to the V4L2 asynchronous subdevice framework. [Sakari Ailus: Remove extra call to v4l2_i2c_subdev_set_name] Signed-off-by:
Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by:
-
