- 26 Jan, 2013 18 commits
-
-
Oliver Hartkopp authored
To prevent a possible misconfiguration (e.g. circular CAN frame routings) limit the number of routings of a single CAN frame to a small variable value. The limit can be specified by the module parameter 'max_hops' (1..6). The default value is 1 (one hop), according to the original can-gw behaviour. Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Oliver Hartkopp authored
Introduce new configuration flag CGW_FLAGS_CAN_IIF_TX_OK to configure if a CAN sk_buff that has been routed with can-gw is allowed to be send back to the originating CAN interface. Signed-off-by:
-
Oliver Hartkopp authored
The struct can_skb_priv is used to transport additional information along with the stored struct can(fd)_frame that can not be contained in existing struct sk_buff elements. can_skb_priv is located in the skb headroom, which does not touch the existing CAN sk_buff usage with skb->data and skb->len, so that even out-of-tree CAN drivers can be used without changes. Btw. out-of-tree CAN drivers without can_skb_priv in the sk_buff headroom would not support features based on can_skb_priv. The can_skb_priv->ifindex contains the first interface where the CAN frame appeared on the local host. Unfortunately skb->skb_iif can not be used as this value is overwritten in every netif_receive_skb() call. Signed-off-by:
-
Bernd Krumboeck authored
Add support for canbus activity led indicators on usb_8dev devices by calling appropriate can_led functions. These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op otherwise. Signed-off-by:
Bernd Krumboeck <krumboeck@universalnet.at> Signed-off-by:
Fabio Baltieri <fabio.baltieri@gmail.com> Signed-off-by:
-
Fabio Baltieri authored
Add support for canbus activity led indicators on sja1000 devices by calling appropriate can_led functions. These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op otherwise. Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Fabio Baltieri authored
Add support for canbus activity led indicators on mcp251x devices by calling appropriate can_led functions. These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op otherwise. Cc: Christian Pellegrin <chripell@fsfe.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Fabio Baltieri authored
Add support for canbus activity led indicators on c_can devices by calling appropriate can_led functions. These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op otherwise. Cc: Bhupesh Sharma <bhupesh.sharma@st.com> Cc: AnilKumar Ch <anilkumar@ti.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Fabio Baltieri authored
Add support for canbus activity led indicators on ti_hecc devices by calling appropriate can_led functions. These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op otherwise. Cc: Anant Gole <anantgole@ti.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Fabio Baltieri authored
Add support for canbus activity led indicators on at91_can devices by calling appropriate can_led functions. These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op otherwise. Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Fabio Baltieri authored
Add support for canbus activity led indicators on flexcan devices by calling appropriate can_led_* functions. These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op otherwise. Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Kurt Van Dijck authored
The LED trigger name for CAN devices is based on the initial CAN device name, but does never change. The LED trigger name is not guaranteed to be unique in case of hotplugging CAN devices. This patch tries to address this problem by modifying the LED trigger name according to the CAN device name when the latter changes. v1 - Kurt Van Dijck v2 - Fabio Baltieri - remove rename blocking if trigger is bound - use led-subsystem function for the actual rename (still WiP) - call init/exit functions from dev.c v3 - Kurt Van Dijck - safe operation for non-candev based devices (vcan, slcan) based on earlier patch v4 - Kurt Van Dijck - trivial patch mistakes fixed Signed-off-by:
Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by:
-
Kurt Van Dijck authored
In net_device notifier calls, it was impossible to determine if a CAN device is based on candev in a safe way. This patch adds such test in order to access candev storage from within those notifiers. Signed-off-by:
-
Fabio Baltieri authored
This patch implements the functions to add two LED triggers, named <ifname>-tx and <ifname>-rx, to a canbus device driver. Triggers are called from specific handlers by each CAN device driver and can be disabled altogether with a Kconfig option. The implementation keeps the LED on when the interface is UP and blinks the LED on network activity at a configurable rate. This only supports can-dev based drivers, as it uses some support field in the can_priv structure. Supported drivers should call devm_can_led_init() and can_led_event() as needed. Cleanup is handled automatically by devres, so no *_exit function is needed. Supported events are: - CAN_LED_EVENT_OPEN: turn on tx/rx LEDs - CAN_LED_EVENT_STOP: turn off tx/rx LEDs - CAN_LED_EVENT_TX: trigger tx LED blink - CAN_LED_EVENT_RX: trigger tx LED blink Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Bernd Krumboeck authored
Add device driver for USB2CAN interface from "8 devices" (http://www.8devices.com). changes since v10: * small cleanups changes since v9: * fixed syslog messages * fixed crc error number * increased MAX_RX_URBS and MAX_TX_URBS changes since v8: * remove all sysfs files changes since v7: * add sysfs documentation * fix minor styling issue * fixed can state for passive mode * changed handling for crc errors changes since v6: * changed some variable types to big endian equivalent * small cleanups changes since v5: * unlock mutex on error changes since v4: * removed FSF address * renamed struct usb_8dev * removed unused variable free_slots * replaced some _to_cpu functions with pointer equivalent * fix return value for usb_8dev_set_mode * handle can errors with separate function * fix overrun error handling * rewrite error handling for usb_8dev_start_xmit * fix urb submit in usb_8dev_start * various small fixes Acked-by:
Wolfgang Grandegger <wg@grandegger.com> Tested-by:
-
Marc Kleine-Budde authored
This patch changes the indention of the Kconfig help text to the default <tab> + 2 <space>. Signed-off-by: -
Marc Kleine-Budde authored
This patch enables all basic CAN protocol by default. Signed-off-by: -
Marc Kleine-Budde authored
This patch adds an 'if CAN_DEV...endif' Block around the CAN driver symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies can be removed. Signed-off-by: -
Marc Kleine-Budde authored
This patch adds an 'if CAN...endif' Block around all CAN symbols in net/can/Kconfig. So the 'depends on CAN' dependencies can be removed. Signed-off-by:
-
- 23 Jan, 2013 22 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-nextDavid S. Miller authored
Steffen Klassert says: ==================== 1) Add a statistic counter for invalid output states and remove a superfluous state valid check, from Li RongQing. 2) Probe for asynchronous block ciphers instead of synchronous block ciphers to make the asynchronous variants available even if no synchronous block ciphers are found, from Jussi Kivilinna. 3) Make rfc3686 asynchronous block cipher and make use of the new asynchronous variant, from Jussi Kivilinna. 4) Replace some rwlocks by rcu, from Cong Wang. 5) Remove some unused defines. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Ariel Elior authored
When posting a message on the bulletin board, the PF calculates crc over the message and places the result in the message. When the VF samples the Bulletin Board it copies the message aside and validates this crc. The length of the message is crucial here and must be the same in both parties. Since the PF is running in the Hypervisor and the VF is running in a Vm, they can possibly be of different versions. As the Bulletin Board is designed to grow forward in future versions, in the VF the length must not be the size of the message structure but instead it should be a field in the message itself. Signed-off-by:
Ariel Elior <ariele@broadcom.com> Signed-off-by:
Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by:
-
Yuval Mintz authored
Commit 823e1d90 caused bnx2x to fail once BNX2X_STOP_ON_ERROR is set. Fixes compilation by moving function declarations between header files. Signed-off-by:
-
Michael Chan authored
In INTA mode, cnic and bnx2x share the same IRQ. During chip reset, for example, cnic will stop servicing IRQs after it has shutdown the cnic hardware resources. However, the shared IRQ is still active as bnx2x needs to finish the reset. There is a window when bnx2x does not know that cnic is no longer handling IRQ and things don't always work properly. Add a flag to tell bnx2x that cnic is handling IRQ. The flag is set before the first cnic IRQ is expected and cleared when no more cnic IRQs are expected, so there should be no race conditions. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
-
Yuval Mintz authored
Fix an incorrect SR-IOV memory release which was committed in 1ab4434c. Signed-off-by:
-
Yuval Mintz authored
Remove most of the sparse warnings in the bnx2x compilation (i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__'). Signed-off-by:
-
Yuval Mintz authored
Don't unload the bnx2x driver if its in a recovery process, or if the previous load have failed. Signed-off-by:
-
Dmitry Kravkov authored
Since commit 15192a8c there have been a memory leak upon rmmod of the bnx2x driver. This corrects the memory leak and corrects the zeroing of internal memories upon driver load. Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
-
Yuval Mintz authored
Add missing 57712_VF and 57800_VF to CHIP_IS_E2 and CHIP_IS_E3 macros (missing from commit 8395be5e). Signed-off-by:
-
Yuval Mintz authored
Add/Revise several debug prints in the bnx2x driver - on regular flows as well as error flows. Signed-off-by:
-
Yuval Mintz authored
Change the incorrect usage of `usleep_range(1000, 1000)' into `usleep_range(1000, 2000)'. Signed-off-by:
-
Yuval Mintz authored
Slightly changes the bnx2x code without `true' functional changes. Changes include: 1. Gathering macros into a single macro when combination is used multiple times. 2. Exporting parts of functions into their own functions. 3. Return values after if-else instead of only on the else condition (where current flow would simply return same value later in the code) 4. Removing some unnecessary code (either dead-code or incorrect conditions) Signed-off-by: -
Yuval Mintz authored
Mostly corrects white spaces, indentations, and comments. Signed-off-by:
-
Claudiu Manoil authored
Reactivate promiscuous mode in H/W upon gfar_init_mac(), if the net dev requires it (IFF_PROMISC flag set). This way the promisc mode is preserved accross device reset conditions like tx timeout, device restore, a.s.o. Signed-off-by:
Voncken C Acksys <cedric.voncken@acksys.fr> Signed-off-by:
Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by:
-
David S. Miller authored
Tom Herbert says: ==================== This series implements so_reuseport (SO_REUSEPORT socket option) for TCP and UDP. For TCP, so_reuseport allows multiple listener sockets to be bound to the same port. In the case of UDP, so_reuseport allows multiple sockets to bind to the same port. To prevent port hijacking all sockets bound to the same port using so_reuseport must have the same uid. Received packets are distributed to multiple sockets bound to the same port using a 4-tuple hash. The motivating case for so_resuseport in TCP would be something like a web server binding to port 80 running with multiple threads, where each thread might have it's own listener socket. This could be done as an alternative to other models: 1) have one listener thread which dispatches completed connections to workers. 2) accept on a single listener socket from multiple threads. In case #1 the listener thread can easily become the bottleneck with high connection turn-over rate. In case #2, the proportion of connections accepted per thread tends to be uneven under high connection load (assuming simple event loop: while (1) { accept(); process() }, wakeup does not promote fairness among the sockets. We have seen the disproportion to be as high as 3:1 ratio between thread accepting most connections and the one accepting the fewest. With so_reusport the distribution is uniform. The TCP implementation has a problem in that the request sockets for a listener are attached to a listener socket. If a SYN is received, a listener socket is chosen and request structure is created (SYN-RECV state). If the subsequent ack in 3WHS does not match the same port by so_reusport, the connection state is not found (reset) and the request structure is orphaned. This scenario would occur when the number of listener sockets bound to a port changes (new ones are added, or old ones closed). We are looking for a solution to this, maybe allow multiple sockets to share the same request table... The motivating case for so_reuseport in UDP would be something like a DNS server. An alternative would be to recv on the same socket from multiple threads. As in the case of TCP, the load across these threads tends to be disproportionate and we also see a lot of contection on the socket lock. Note that SO_REUSEADDR already allows multiple UDP sockets to bind to the same port, however there is no provision to prevent hijacking and nothing to distribute packets across all the sockets sharing the same bound port. This patch does not change the semantics of SO_REUSEADDR, but provides usable functionality of it for unicast. ==================== Signed-off-by: -
Tom Herbert authored
Motivation for soreuseport would be something like a DNS server. An alternative would be to recv on the same socket from multiple threads. As in the case of TCP, the load across these threads tends to be disproportionate and we also see a lot of contection on the socket lock. Note that SO_REUSEADDR already allows multiple UDP sockets to bind to the same port, however there is no provision to prevent hijacking and nothing to distribute packets across all the sockets sharing the same bound port. This patch does not change the semantics of SO_REUSEADDR, but provides usable functionality of it for unicast. Signed-off-by:
Tom Herbert <therbert@google.com> Signed-off-by:
-
Tom Herbert authored
Motivation for soreuseport would be something like a web server binding to port 80 running with multiple threads, where each thread might have it's own listener socket. This could be done as an alternative to other models: 1) have one listener thread which dispatches completed connections to workers. 2) accept on a single listener socket from multiple threads. In case #1 the listener thread can easily become the bottleneck with high connection turn-over rate. In case #2, the proportion of connections accepted per thread tends to be uneven under high connection load (assuming simple event loop: while (1) { accept(); process() }, wakeup does not promote fairness among the sockets. We have seen the disproportion to be as high as 3:1 ratio between thread accepting most connections and the one accepting the fewest. With so_reusport the distribution is uniform. Signed-off-by: -
Tom Herbert authored
Allow multiple UDP sockets to bind to the same port. Motivation soreuseport would be something like a DNS server. An alternative would be to recv on the same socket from multiple threads. As in the case of TCP, the load across these threads tends to be disproportionate and we also see a lot of contection on the socketlock. Note that SO_REUSEADDR already allows multiple UDP sockets to bind to the same port, however there is no provision to prevent hijacking and nothing to distribute packets across all the sockets sharing the same bound port. This patch does not change the semantics of SO_REUSEADDR, but provides usable functionality of it for unicast. Signed-off-by:
-
Tom Herbert authored
Allow multiple listener sockets to bind to the same port. Motivation for soresuseport would be something like a web server binding to port 80 running with multiple threads, where each thread might have it's own listener socket. This could be done as an alternative to other models: 1) have one listener thread which dispatches completed connections to workers. 2) accept on a single listener socket from multiple threads. In case #1 the listener thread can easily become the bottleneck with high connection turn-over rate. In case #2, the proportion of connections accepted per thread tends to be uneven under high connection load (assuming simple event loop: while (1) { accept(); process() }, wakeup does not promote fairness among the sockets. We have seen the disproportion to be as high as 3:1 ratio between thread accepting most connections and the one accepting the fewest. With so_reusport the distribution is uniform. Signed-off-by: -
Tom Herbert authored
Definitions and macros for implementing soreusport. Signed-off-by:
-
Matt Wilson authored
Sometimes it is useful to be able to change the MAC address of the interface for netback devices. For example, when using ebtables it may be useful to be able to distinguish traffic from different interfaces without depending on the interface name. Reported-by:
Nikita Borzykh <sample.n@gmail.com> Reported-by:
Paul Harvey <stockingpaul@hotmail.com> Cc: netdev@vger.kernel.org Cc: xen-devel@lists.xen.org Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by:
Ian Campbell <ian.campbell@citrix.com> Signed-off-by:
Matt Wilson <msw@amazon.com> Reviewed-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Cong Wang authored
Fengguang reported: net/core/netpoll.c: In function 'netpoll_setup': net/core/netpoll.c:1049:6: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized] in !CONFIG_IPV6 case, we may error out without initializing 'err'. Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Cong Wang <amwang@redhat.com> Signed-off-by:
-
