Merge tag 'asoc-fix-v5.11-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v5.11

A few more fixes for v5.11, mostly around HDA jack detection, plus
a couple of updates to the MAINTAINERS entries.

For addressing the regression on Pioneer devices, we recently
corrected the quirk code to enable the implicit feedback mode on those
devices properly.  However, the devices still showed problems with the
full duplex operations with JACK, and after debug sessions, we figured
out that the older kernels that had worked with JACK also didn't use
the implicit feedback mode at all although they had the quirk code to
enable it; instead, the old code worked just to skip the normal sync
endpoint setup that would have been detected without it.  IOW, what
broke without the implicit-fb quirk in the past was the application of
the normal sync endpoint that is actually the capture data endpoint on
these devices.

This patch covers the overseen piece: it modifies the quirk code again
not to enable the implicit feedback mode but just to make the driver
skipping the sync endpoint detection.  This made the driver working
with JACK full-duplex mode again.

Still it's not quite clear why the implicit feedback doesn't work on
those devices yet; maybe it's about some issues in the URB setup.  But
at least, with this patch, the driver should work in the level of the
older kernels again.

Fixes: 167c9dc8 ("ALSA: usb-audio: Fix implicit feedback sync setup for Pioneer devices")
Link: https://lore.kernel.org/r/20210118075816.25068-4-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The UAC2/3 sample rate setup is based on the clock node, which is
usually shared in the interface, and can't be re-setup without
deselecting the interface once, and that's how the current code
behaves.  OTOH, the sample rate setup of UAC1 is per endpoint, hence
we basically need to call for each endpoint usage even if those share
the same interface.

This patch fixes the behavior of UAC1 to call always
snd_usb_init_sample_rate() in snd_usb_endpoint_configure().

Fixes: bf6313a0 ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210118075816.25068-3-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The current sample rate setup function for UAC1 assumes only the first
endpoint retrieved from the interface:altset pair, but the rate set up
may be needed also for the secondary endpoint.  Also, retrieving the
endpoint number from the interface descriptor is redundant; we have
already the target endpoint in the given audioformat object.

This patch simplifies the code and corrects the target endpoint as
described in the above.  It simply refers to fmt->endpoint directly.

Also, this patch drops the pioneer_djm_set_format_quirk() that is
caleld from snd_usb_set_format_quirk(); this function does the sample
rate setup but for the capture endpoint (0x82), and that's exactly
what the change above fixes.

Link: https://lore.kernel.org/r/20210118075816.25068-2-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Add full list of ASoC drivers that are maintained!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210115165520.6023-2-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add myself as maintainer of qcom audio drivers, as Patrick
has very little time to look at the patches.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Acked-by: Patrick Lai <plai@codeaurora.org>
Link: https://lore.kernel.org/r/20210115165520.6023-1-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add HD Audio Device PCI ID for the Intel Cometlake-R platform
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Kai-Chuan Hsieh <kaichuan.hsieh@canonical.com>
Link: https://lore.kernel.org/r/20210115031515.13100-1-kaichuan.hsieh@canonical.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

snd_seq_oss_synth_make_info() didn't check the error code from
snd_seq_oss_midi_make_info(), and this leads to the call of strlcpy()
with the uninitialized string as the source, which may lead to the
access over the limit.

Add the proper error check for avoiding the failure.

Reported-by: syzbot+e42504ff21cff05a595f@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210115093428.15882-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

It turned out that VIA codecs also mute the sound in the lowest mixer
level.  Turn on the dac_min_mute flag to indicate the mute-as-minimum
in TLV like already done in Conexant and IDT codecs.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210559
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210114072453.11379-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The Acer Apire E5-575T laptop with codec ALC255 has a terrible
background noise comes from internal mic capture. And the jack
sensing dose not work for headset like some other Acer laptops.

This patch limits the internal mic boost on top of the existing
ALC255_FIXUP_ACER_MIC_NO_PRESENCE quirk for Acer Aspire E5-575T.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210114082728.74729-1-chiu@endlessos.orgSigned-off-by: Takashi Iwai <tiwai@suse.de>

Since the commit 5a6c3e11 ("ALSA: usb-audio: Add hw constraint for
implicit fb sync"), we apply the hw constraints for the implicit
feedback sync to make the secondary open aligned with the already
opened stream setup.  This change assumed that the secondary open is
performed after the first stream has been already set up, and adds the
hw constraints to sync with the first stream's parameters only when
the EP setup for the first stream was confirmed at the open time.
However, most of applications handling the full-duplex operations do
open both playback and capture streams at first, then set up both
streams.  This results in skipping the additional hw constraints since
the counter-part stream hasn't been set up yet at the open of the
second stream, and it eventually leads to "incompatible EP" error in
the end.

This patch corrects the behavior by always applying the hw constraints
for the implicit fb sync.  The hw constraint rules are defined so that
they check the sync EP dynamically at each invocation, instead.  This
covers the concurrent stream setups better and lets the hw refine
calls resolving to the right configuration.

Also this patch corrects a minor error that has existed in the debug
print that isn't built as default.

Fixes: 5a6c3e11 ("ALSA: usb-audio: Add hw constraint for implicit fb sync")
Link: https://lore.kernel.org/r/20210111081611.12790-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The earlier commit to fix runtime PM in case i915 init fails,
introduces a possibility to hit a page fault.

snd_hdac_ext_bus_device_exit() is designed to be called from
dev.release(). Calling it outside device reference counting, is
not safe and may lead to calling the device_exit() function
twice. Additionally, as part of ext_bus_device_init(), the device
is also registered with snd_hdac_device_register(). Thus before
calling device_exit(), the device must be removed from device
hierarchy first.

Fix the issue by rolling back init actions by calling
hdac_device_unregister() and then releasing device with put_device().
This matches with existing code in hdac-ext module.

To complete the fix, add handling for the case where
hda_codec_load_module() returns -ENODEV, and clean up the hdac_ext
resources also in this case.

In future work, hdac-ext interface should be extended to allow clients
more flexibility to handle the life-cycle of individual devices, beyond
just the current snd_hdac_ext_bus_device_remove(), which removes all
devices.

BugLink: https://github.com/thesofproject/linux/issues/2646Reported-by: Jaroslav Kysela <perex@perex.cz>
Fixes: 6c63c954 ("ASoC: SOF: fix a runtime pm issue in SOF when HDMI codec doesn't work")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210113150715.3992635-1-kai.vehmanen@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add HD Audio PCI ID and HDMI codec vendor ID for Intel AlderLake-P.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210113155629.4097057-1-kai.vehmanen@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

System takes a very long time to suspend after commit 215a22ed
("ALSA: hda: Refactor codec PM to use direct-complete optimization"):
[   90.065964] PM: suspend entry (s2idle)
[   90.067337] Filesystems sync: 0.001 seconds
[   90.185758] Freezing user space processes ... (elapsed 0.002 seconds) done.
[   90.188713] OOM killer disabled.
[   90.188714] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[   90.190024] printk: Suspending console(s) (use no_console_suspend to debug)
[   90.904912] intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [49C], continue to suspend
[  321.262505] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[  328.426919] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[  329.490933] ACPI: EC: interrupt blocked

That commit keeps the codec suspended during the system suspend. However,
mute/micmute LED will clear codec's direct-complete flag by
dpm_clear_superiors_direct_complete().

This doesn't play well with SOF driver. When its runtime resume is
called for system suspend, hda_codec_jack_check() schedules
jackpoll_work which uses snd_hdac_is_power_on() to check whether codec
is suspended. Because the direct-complete path isn't taken,
pm_runtime_disable() isn't called so snd_hdac_is_power_on() returns
false and jackpoll continues to run, and snd_hda_power_up_pm() cannot
power up an already suspended codec in multiple attempts, causes the
long delay on system suspend:

if (dev->power.direct_complete) {
	if (pm_runtime_status_suspended(dev)) {
		pm_runtime_disable(dev);
		if (pm_runtime_status_suspended(dev)) {
			pm_dev_dbg(dev, state, "direct-complete ");
			goto Complete;
		}

		pm_runtime_enable(dev);
	}
	dev->power.direct_complete = false;
}

When direct-complete path is taken, snd_hdac_is_power_on() returns true
and hda_jackpoll_work() is skipped by accident. So this is still not
correct.

If we were to use snd_hdac_is_power_on() in system PM path,
pm_runtime_status_suspended() should be used instead of
pm_runtime_suspended(), otherwise pm_runtime_{enable,disable}() may
change the outcome of snd_hdac_is_power_on().

Because devices suspend in reverse order (i.e. child first), it doesn't
make much sense to resume an already suspended codec from audio
controller. So avoid the issue by making sure jackpoll isn't used in
system PM process.

Fixes: 215a22ed ("ALSA: hda: Refactor codec PM to use direct-complete optimization")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-3-kai.heng.feng@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Modify hda_codec_jack_wake_enable() to also support disable WAKEEN.
In addition, this patch also moves the WAKEEN disablement call out of
hda_codec_jack_check() into hda_codec_jack_wake_enable().

This is a preparation for next patch.

No functional change intended.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-2-kai.heng.feng@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of queueing jackpoll_work, runtime resume the codec to let it
use different jack detection methods based on jackpoll_interval.

This partially matches SOF driver's behavior with commit a6e7d0a4
("ALSA: hda: fix jack detection with Realtek codecs when in D3"), the
difference is SOF unconditionally resumes the codec.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-1-kai.heng.feng@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Changeset 81437cc3 ("Merge series "dt-bindings: stm32: convert audio dfsdm to json-schema" from Olivier Moysan <olivier.moysan@st.com>:")
removed bindings/sound/st,stm32-adfsdm.txt, as stm32-* audio
bindings are now under: bindings/iio/adc/st,stm32-*.yaml.

Update cross-references to them accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/03950bbd5cf7bac10eaaff3725e283d3ec2538c5.1610536535.git.mchehab+huawei@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

We are able to power down the GPU and audio via the GPU driver
so flag these asics as supporting runtime pm.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20210105175245.963451-1-alexander.deucher@amd.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

As snd_fw_async_midi_port.consume_bytes is unsigned int, and
NSEC_PER_SEC is 1000000000L, the second multiplication in

    port->consume_bytes * 8 * NSEC_PER_SEC / 31250

always overflows on 32-bit platforms, truncating the result.  Fix this
by precalculating "NSEC_PER_SEC / 31250", which is an integer constant.

Note that this assumes port->consume_bytes <= 16777.

Fixes: 531f4718 ("ALSA: firewire-lib/firewire-tascam: localize async midi port")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210111130251.361335-3-geert+renesas@glider.beSigned-off-by: Takashi Iwai <tiwai@suse.de>

As snd_ff.rx_bytes[] is unsigned int, and NSEC_PER_SEC is 1000000000L,
the second multiplication in

    ff->rx_bytes[port] * 8 * NSEC_PER_SEC / 31250

always overflows on 32-bit platforms, truncating the result.  Fix this
by precalculating "NSEC_PER_SEC / 31250", which is an integer constant.

Note that this assumes ff->rx_bytes[port] <= 16777.

Fixes: 19174295 ("ALSA: fireface: add transaction support")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210111130251.361335-2-geert+renesas@glider.beSigned-off-by: Takashi Iwai <tiwai@suse.de>

Currently hda on tegra30 fails to open a stream with an input/output error.

For example:
speaker-test -Dhw:0,3 -c 2

speaker-test 1.2.2

Playback device is hw:0,3
Stream parameters are 48000Hz, S16_LE, 2 channels
Using 16 octaves of pink noise
Rate set to 48000Hz (requested 48000Hz)
Buffer size range from 64 to 16384
Period size range from 32 to 8192
Using max buffer size 16384
Periods = 4
was set period_size = 4096
was set buffer_size = 16384
 0 - Front Left
Write error: -5,Input/output error
xrun_recovery failed: -5,Input/output error
Transfer failed: Input/output error

The tegra-hda device was introduced in tegra30 but only utilized in
tegra124 until recent chips. Tegra210/186 work only due to a hardware
change. For this reason it is unknown when this issue first manifested.
Discussions with the hardware team show this applies to all current tegra
chips. It has been resolved in the tegra234, which does not have hda
support at this time.

The explanation from the hardware team is this:
Below is the striping formula referenced from HD audio spec.
   { ((num_channels * bits_per_sample) / number of SDOs) >= 8 }

The current issue is seen because Tegra HW has a problem with boundary
condition (= 8) for striping. The reason why it is not seen on
Tegra210/Tegra186 is because it uses max 2SDO lines. Max SDO lines is
read from GCAP register.

For the given stream (channels = 2, bps = 16);
ratio = (channels * bps) / NSDO = 32 / NSDO;

On Tegra30,      ratio = 32/4 = 8  (FAIL)
On Tegra210/186, ratio = 32/2 = 16 (PASS)
On Tegra194,     ratio = 32/4 = 8  (FAIL) ==> Earlier workaround was
applied for it

If Tegra210/186 is forced to use 4SDO, it fails there as well. So the
behavior is consistent across all these chips.

Applying the fix in [1] universally resolves this issue on tegra30-hda.
Tested on the Ouya game console and the tf201 tablet.

[1] commit 60019d8c ("ALSA: hda/tegra: workaround playback failure on
Tegra194")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ion Agorria <ion@agorria.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20210108135913.2421585-3-pgwipeout@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Current implementation defaults the hda clocks to clk_m. This causes hda
to run too slow to operate correctly. Fix this by defaulting to pll_p and
setting the frequency to the correct rate.

This matches upstream t124 and downstream t30.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20210108135913.2421585-2-pgwipeout@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

MIXART.txt has been converted to ReST and renamed. Fix the reference
in alsa-configuration.rst.

Fixes: 3d8e8186 ("ALSA: doc: ReSTize MIXART.txt")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210101221942.1068388-1-j.neuschaefer@gmx.netSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Search for <ncurses.h> in the default header path of HOSTCC

 - Tweak the option order to be kind to old BSD awk

 - Remove 'kvmconfig' and 'xenconfig' shorthands

 - Fix documentation

* tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  Documentation: kbuild: Fix section reference
  kconfig: remove 'kvmconfig' and 'xenconfig' shorthands
  lib/raid6: Let $(UNROLL) rules work with macOS userland
  kconfig: Support building mconf with vendor sysroot ncurses
  kconfig: config script: add a little user help
  MAINTAINERS: adjust GCC PLUGINS after gcc-plugin.sh removal

Pull SCSI fixes from James Bottomley:
 "This is two driver fixes (megaraid_sas and hisi_sas).

  The megaraid one is a revert of a previous revert of a cpu hotplug fix
  which exposed a bug in the block layer which has been fixed in this
  merge window.

  The hisi_sas performance enhancement comes from switching to interrupt
  managed completion queues, which depended on the addition of
  devm_platform_get_irqs_affinity() which is now upstream via the irq
  tree in the last merge window"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: hisi_sas: Expose HW queues for v2 hw
  Revert "Revert "scsi: megaraid_sas: Added support for shared host tagset for cpuhotplug""

Pull block fixes from Jens Axboe:

 - Missing CRC32 selections (Arnd)

 - Fix for a merge window regression with bdev inode init (Christoph)

 - bcache fixes

 - rnbd fixes

 - NVMe pull request from Christoph:
    - fix a race in the nvme-tcp send code (Sagi Grimberg)
    - fix a list corruption in an nvme-rdma error path (Israel Rukshin)
    - avoid a possible double fetch in nvme-pci (Lalithambika Krishnakumar)
    - add the susystem NQN quirk for a Samsung driver (Gopal Tiwari)
    - fix two compiler warnings in nvme-fcloop (James Smart)
    - don't call sleeping functions from irq context in nvme-fc (James Smart)
    - remove an unused argument (Max Gurtovoy)
    - remove unused exports (Minwoo Im)

 - Use-after-free fix for partition iteration (Ming)

 - Missing blk-mq debugfs flag annotation (John)

 - Bdev freeze regression fix (Satya)

 - blk-iocost NULL pointer deref fix (Tejun)

* tag 'block-5.11-2021-01-10' of git://git.kernel.dk/linux-block: (26 commits)
  bcache: set bcache device into read-only mode for BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET
  bcache: introduce BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE for large bucket
  bcache: check unsupported feature sets for bcache register
  bcache: fix typo from SUUP to SUPP in features.h
  bcache: set pdev_set_uuid before scond loop iteration
  blk-mq-debugfs: Add decode for BLK_MQ_F_TAG_HCTX_SHARED
  block/rnbd-clt: avoid module unload race with close confirmation
  block/rnbd: Adding name to the Contributors List
  block/rnbd-clt: Fix sg table use after free
  block/rnbd-srv: Fix use after free in rnbd_srv_sess_dev_force_close
  block/rnbd: Select SG_POOL for RNBD_CLIENT
  block: pre-initialize struct block_device in bdev_alloc_inode
  fs: Fix freeze_bdev()/thaw_bdev() accounting of bd_fsfreeze_sb
  nvme: remove the unused status argument from nvme_trace_bio_complete
  nvmet-rdma: Fix list_del corruption on queue establishment failure
  nvme: unexport functions with no external caller
  nvme: avoid possible double fetch in handling CQE
  nvme-tcp: Fix possible race of io_work and direct send
  nvme-pci: mark Samsung PM1725a as IGNORE_DEV_SUBNQN
  nvme-fcloop: Fix sscanf type and list_first_entry_or_null warnings
  ...

Pull io_uring fixes from Jens Axboe:
 "A bit larger than I had hoped at this point, but it's all changes that
  will be directed towards stable anyway. In detail:

   - Fix a merge window regression on error return (Matthew)

   - Remove useless variable declaration/assignment (Ye Bin)

   - IOPOLL fixes (Pavel)

   - Exit and cancelation fixes (Pavel)

   - fasync lockdep complaint fix (Pavel)

   - Ensure SQPOLL is synchronized with creator life time (Pavel)"

* tag 'io_uring-5.11-2021-01-10' of git://git.kernel.dk/linux-block:
  io_uring: stop SQPOLL submit on creator's death
  io_uring: add warn_once for io_uring_flush()
  io_uring: inline io_uring_attempt_task_drop()
  io_uring: io_rw_reissue lockdep annotations
  io_uring: synchronise ev_posted() with waitqueues
  io_uring: dont kill fasync under completion_lock
  io_uring: trigger eventfd for IOPOLL
  io_uring: Fix return value from alloc_fixed_file_ref_node
  io_uring: Delete useless variable ‘id’ in io_prep_async_work
  io_uring: cancel more aggressively in exit_work
  io_uring: drop file refs after task cancel
  io_uring: patch up IOPOLL overflow_flush sync
  io_uring: synchronise IOPOLL on task_submit fail

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 5.11-rc3.

  Include in here are:

   - USB gadget driver fixes for reported issues

   - new usb-serial driver ids

   - dma from stack bugfixes

   - typec bugfixes

   - dwc3 bugfixes

   - xhci driver bugfixes

   - other small misc usb driver bugfixes

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
  usb: dwc3: gadget: Clear wait flag on dequeue
  usb: typec: Send uevent for num_altmodes update
  usb: typec: Fix copy paste error for NVIDIA alt-mode description
  usb: gadget: enable super speed plus
  kcov, usb: hide in_serving_softirq checks in __usb_hcd_giveback_urb
  usb: uas: Add PNY USB Portable SSD to unusual_uas
  usb: gadget: configfs: Preserve function ordering after bind failure
  usb: gadget: select CONFIG_CRC32
  usb: gadget: core: change the comment for usb_gadget_connect
  usb: gadget: configfs: Fix use-after-free issue with udc_name
  usb: dwc3: gadget: Restart DWC3 gadget when enabling pullup
  usb: usbip: vhci_hcd: protect shift size
  USB: usblp: fix DMA to stack
  USB: serial: iuu_phoenix: fix DMA from stack
  USB: serial: option: add LongSung M5710 module support
  USB: serial: option: add Quectel EM160R-GL
  USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug
  usb: gadget: f_uac2: reset wMaxPacketSize
  usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression
  usb: dwc3: ulpi: Replace CPU-based busyloop with Protocol-based one
  ...

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for 5.11-rc3. Nothing major,
  just resolving some reported issues:

   - cleanup some remaining mentions of the ION drivers that were
     removed in 5.11-rc1

   - comedi driver bugfix

   - two error path memory leak fixes

  All have been in linux-next for a while with no reported issues"

* tag 'staging-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: ION: remove some references to CONFIG_ION
  staging: mt7621-dma: Fix a resource leak in an error handling path
  Staging: comedi: Return -EFAULT if copy_to_user() fails
  staging: spmi: hisi-spmi-controller: Fix some error handling paths

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.11-rc3.

  The majority here are fixes for the habanalabs drivers, but also in
  here are:

   - crypto driver fix

   - pvpanic driver fix

   - updated font file

   - interconnect driver fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (26 commits)
  Fonts: font_ter16x32: Update font with new upstream Terminus release
  misc: pvpanic: Check devm_ioport_map() for NULL
  speakup: Add github repository URL and bug tracker
  MAINTAINERS: Update Georgi's email address
  crypto: asym_tpm: correct zero out potential secrets
  habanalabs: Fix memleak in hl_device_reset
  interconnect: imx8mq: Use icc_sync_state
  interconnect: imx: Remove a useless test
  interconnect: imx: Add a missing of_node_put after of_device_is_available
  interconnect: qcom: fix rpmh link failures
  habanalabs: fix order of status check
  habanalabs: register to pci shutdown callback
  habanalabs: add validation cs counter, fix misplaced counters
  habanalabs/gaudi: retry loading TPC f/w on -EINTR
  habanalabs: adjust pci controller init to new firmware
  habanalabs: update comment in hl_boot_if.h
  habanalabs/gaudi: enhance reset message
  habanalabs: full FW hard reset support
  habanalabs/gaudi: disable CGM at HW initialization
  habanalabs: Revise comment to align with mirror list name
  ...

Section 3.11 was incorrectly called 3.9, fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Pull ARC fixes from Vineet Gupta:

 - Address the 2nd boot failure due to snafu in signal handling code
   (first was generic console ttynull issue)

 - misc other fixes

* tag 'arc-5.11-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [hsdk]: Enable FPU_SAVE_RESTORE
  ARC: unbork 5.11 bootup: fix snafu in _TIF_NOTIFY_SIGNAL handling
  include/soc: remove headers for EZChip NPS
  arch/arc: add copy_user_page() to <asm/page.h> to fix build error on ARC

Pull powerpc fixes from Michael Ellerman:

 - A fix for machine check handling with VMAP stack on 32-bit.

 - A clang build fix.

Thanks to Christophe Leroy and Nathan Chancellor.

* tag 'powerpc-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Handle .text.{hot,unlikely}.* in linker script
  powerpc/32s: Fix RTAS machine check with VMAP stack

Pull x86 fixes from Borislav Petkov:
 "As expected, fixes started trickling in after the holidays so here is
  the accumulated pile of x86 fixes for 5.11:

   - A fix for fanotify_mark() missing the conversion of x86_32 native
     syscalls which take 64-bit arguments to the compat handlers due to
     former having a general compat handler. (Brian Gerst)

   - Add a forgotten pmd page destructor call to pud_free_pmd_page()
     where a pmd page is freed. (Dan Williams)

   - Make IN/OUT insns with an u8 immediate port operand handling for
     SEV-ES guests more precise by using only the single port byte and
     not the whole s32 value of the insn decoder. (Peter Gonda)

   - Correct a straddling end range check before returning the proper
     MTRR type, when the end address is the same as top of memory.
     (Ying-Tsun Huang)

   - Change PQR_ASSOC MSR update scheme when moving a task to a resctrl
     resource group to avoid significant performance overhead with some
     resctrl workloads. (Fenghua Yu)

   - Avoid the actual task move overhead when the task is already in the
     resource group. (Fenghua Yu)"

* tag 'x86_urgent_for_v5.11_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/resctrl: Don't move a task to the same resource group
  x86/resctrl: Use an IPI instead of task_work_add() to update PQR_ASSOC MSR
  x86/mtrr: Correct the range check before performing MTRR type lookups
  x86/sev-es: Fix SEV-ES OUT/IN immediate opcode vc handling
  x86/mm: Fix leak of pmd ptlock
  fanotify: Fix sys_fanotify_mark() on native x86-32

Merge tag 'hwmon-for-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Fix possible KASAN issue in amd_energy driver

 - Avoid configuration problem in pwm-fan driver

 - Fix kernel-doc warning in sbtsi_temp documentation

* tag 'hwmon-for-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (amd_energy) fix allocation of hwmon_channel_info config
  hwmon: (pwm-fan) Ensure that calculation doesn't discard big period values
  hwmon: (sbtsi_temp) Fix Documenation kernel-doc warning

Pull dmaengine fixes from Vinod Koul:
 "A bunch of dmaengine driver fixes for:

   - coverity discovered issues for xilinx driver

   - qcom, gpi driver fix for undefined bhaviour and one off cleanup

   - update Peter's email for TI DMA drivers

   - one-off for idxd driver

   - resource leak fix for mediatek and milbeaut drivers"

* tag 'dmaengine-fix-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
  dmaengine: stm32-mdma: fix STM32_MDMA_VERY_HIGH_PRIORITY value
  dmaengine: xilinx_dma: fix mixed_enum_type coverity warning
  dmaengine: xilinx_dma: fix incompatible param warning in _child_probe()
  dmaengine: xilinx_dma: check dma_async_device_register return value
  dmaengine: qcom: fix gpi undefined behavior
  dt-bindings: dma: ti: Update maintainer and author information
  MAINTAINERS: Add entry for Texas Instruments DMA drivers
  qcom: bam_dma: Delete useless kfree code
  dmaengine: dw-edma: Fix use after free in dw_edma_alloc_chunk()
  dmaengine: milbeaut-xdmac: Fix a resource leak in the error handling path of the probe function
  dmaengine: mediatek: mtk-hsdma: Fix a resource leak in the error handling path of the probe function
  dmaengine: qcom: gpi: Fixes a format mismatch
  dmaengine: idxd: off by one in cleanup code
  dmaengine: ti: k3-udma: Fix pktdma rchan TPL level setup

Pull i2c fixes from Wolfram Sang:
 "Three driver bugfixes for I2C. Buisness as usual"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mediatek: Fix apdma and i2c hand-shake timeout
  i2c: i801: Fix the i2c-mux gpiod_lookup_table not being properly terminated
  i2c: sprd: use a specific timeout to avoid system hang up issue

Change my email contact ahead of a likely painful eleven-month migration
to a certain cobalt enteprisey groupware cloud product that will totally
break my workflow.  Some day I may get used to having to email being
sequestered behind both claret and cerulean oath2+sms 2fa layers, but
for now I'll stick with keying in one password to receive an email vs.
the required four.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>