- 28 Jun, 2022 9 commits
-
-
Oleksij Rempel authored
We should respect link partner capabilities and not force flow control support on every link. Even more, in current state the MAC driver do not advertises pause support so we should not keep flow control enabled at all. Fixes: e532a096 ("net: usb: asix: ax88772: add phylib support") Reported-by:
Anton Lundin <glance@acc.umu.se> Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Tested-by:
Jakub Kicinski <kuba@kernel.org>
-
Oleksij Rempel authored
If cable is attached after probe sequence, the usbnet framework would not automatically start processing RX packets except at least one packet was transmitted. On systems with any kind of address auto configuration this issue was not detected, because some packets are send immediately after link state is changed to "running". With this patch we will notify usbnet about link status change provided by the PHYlib. Fixes: e532a096 ("net: usb: asix: ax88772: add phylib support") Reported-by:
-
Michael Walle authored
Mails to Charles get an auto reply, that he is no longer working at Eff'Innov technologies. Drop the entry and mark the driver as orphaned. Signed-off-by:
Michael Walle <michael@walle.cc> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220626200039.4062784-1-michael@walle.ccSigned-off-by:
-
Shreenidhi Shedi authored
This should be bitwise operator not logical. Fixes: 862cd659 ("octeon_ep: Add driver framework and device initialization") Signed-off-by:
Shreenidhi Shedi <sshedi@vmware.com> Link: https://lore.kernel.org/r/20220626132947.3992423-1-sshedi@vmware.comSigned-off-by:
-
Jakub Kicinski authored
Victor Nogueira says: ==================== Notify user space if any actions were flushed before error This patch series fixes the behaviour of actions flush so that the kernel always notifies user space whenever it deletes actions during a flush operation, even if it didn't flush all the actions. This series also introduces tdc tests to verify this new behaviour. ==================== Link: https://lore.kernel.org/r/20220623140742.684043-1-victor@mojatatu.comSigned-off-by:
-
Victor Nogueira authored
Add tdc test cases to verify new flush behaviour is correct, which do the following: - Try to flush only one action which is being referenced by a filter - Try to flush three actions where the last one (index 3) is being referenced by a filter Signed-off-by:
Victor Nogueira <victor@mojatatu.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
Victor Nogueira authored
If during an action flush operation one of the actions is still being referenced, the flush operation is aborted and the kernel returns to user space with an error. However, if the kernel was able to flush, for example, 3 actions and failed on the fourth, the kernel will not notify user space that it deleted 3 actions before failing. This patch fixes that behaviour by notifying user space of how many actions were deleted before flush failed and by setting extack with a message describing what happened. Fixes: 55334a5d ("net_sched: act: refuse to remove bound action outside") Signed-off-by:
-
Tong Zhang authored
epic_close() calls epic_rx() and uses dma buffer, but in epic_remove_one() we already freed the dma buffer. To fix this issue, reorder function calls like in the .probe function. BUG: KASAN: use-after-free in epic_rx+0xa6/0x7e0 [epic100] Call Trace: epic_rx+0xa6/0x7e0 [epic100] epic_close+0xec/0x2f0 [epic100] unregister_netdev+0x18/0x20 epic_remove_one+0xaa/0xf0 [epic100] Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reported-by:
Yilun Wu <yiluwu@cs.stonybrook.edu> Signed-off-by:
Tong Zhang <ztong0001@gmail.com> Reviewed-by:
Francois Romieu <romieu@fr.zoreil.com> Link: https://lore.kernel.org/r/20220627043351.25615-1-ztong0001@gmail.comSigned-off-by:
-
Jakub Kicinski authored
While looking at a syzbot report I noticed the NAPI only gets disabled before it's deleted. I think that user can detach the queue before destroying the device and the NAPI will never be stopped. Fixes: 94317099 ("tun: enable NAPI for TUN/TAP driver") Acked-by:
Petar Penkov <ppenkov@aviatrix.com> Link: https://lore.kernel.org/r/20220623042105.2274812-1-kuba@kernel.orgSigned-off-by:
-
- 27 Jun, 2022 2 commits
-
-
Xin Long authored
Shuang Li reported a NULL pointer dereference crash: [] BUG: kernel NULL pointer dereference, address: 0000000000000068 [] RIP: 0010:tipc_link_is_up+0x5/0x10 [tipc] [] Call Trace: [] <IRQ> [] tipc_bcast_rcv+0xa2/0x190 [tipc] [] tipc_node_bc_rcv+0x8b/0x200 [tipc] [] tipc_rcv+0x3af/0x5b0 [tipc] [] tipc_udp_recv+0xc7/0x1e0 [tipc] It was caused by the 'l' passed into tipc_bcast_rcv() is NULL. When it creates a node in tipc_node_check_dest(), after inserting the new node into hashtable in tipc_node_create(), it creates the bc link. However, there is a gap between this insert and bc link creation, a bc packet may come in and get the node from the hashtable then try to dereference its bc link, which is NULL. This patch is to fix it by moving the bc link creation before inserting into the hashtable. Note that for a preliminary node becoming "real", the bc link creation should also be called before it's rehashed, as we don't create it for preliminary nodes. Fixes: 4cbf8ac2 ("tipc: enable creating a "preliminary" node") Reported-by:
Shuang Li <shuali@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Jon Maloy <jmaloy@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Recently added debug in commit f9aefd6b ("net: warn if mac header was not set") caught a bug in skb_tunnel_check_pmtu(), as shown in this syzbot report [1]. In ndo_start_xmit() paths, there is really no need to use skb->mac_header, because skb->data is supposed to point at it. [1] WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_mac_header_len include/linux/skbuff.h:2784 [inline] WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413 Modules linked in: CPU: 1 PID: 8604 Comm: syz-executor.3 Not tainted 5.19.0-rc2-syzkaller-00443-g8720bd95 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:skb_mac_header_len include/linux/skbuff.h:2784 [inline] RIP: 0010:skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413 Code: 00 00 00 00 fc ff df 4c 89 fa 48 c1 ea 03 80 3c 02 00 0f 84 b9 fe ff ff 4c 89 ff e8 7c 0f d7 f9 e9 ac fe ff ff e8 c2 13 8a f9 <0f> 0b e9 28 fc ff ff e8 b6 13 8a f9 48 8b 54 24 70 48 b8 00 00 00 RSP: 0018:ffffc90002e4f520 EFLAGS: 00010212 RAX: 0000000000000324 RBX: ffff88804d5fd500 RCX: ffffc90005b52000 RDX: 0000000000040000 RSI: ffffffff87f05e3e RDI: 0000000000000003 RBP: ffffc90002e4f650 R08: 0000000000000003 R09: 000000000000ffff R10: 000000000000ffff R11: 0000000000000000 R12: 000000000000ffff R13: 0000000000000000 R14: 000000000000ffcd R15: 000000000000001f FS: 00007f3babba9700(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000080 CR3: 0000000075319000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> geneve_xmit_skb drivers/net/geneve.c:927 [inline] geneve_xmit+0xcf8/0x35d0 drivers/net/geneve.c:1107 __netdev_start_xmit include/linux/netdevice.h:4805 [inline] netdev_start_xmit include/linux/netdevice.h:4819 [inline] __dev_direct_xmit+0x500/0x730 net/core/dev.c:4309 dev_direct_xmit include/linux/netdevice.h:3007 [inline] packet_direct_xmit+0x1b8/0x2c0 net/packet/af_packet.c:282 packet_snd net/packet/af_packet.c:3073 [inline] packet_sendmsg+0x21f4/0x55d0 net/packet/af_packet.c:3104 sock_sendmsg_nosec net/socket.c:714 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:734 ____sys_sendmsg+0x6eb/0x810 net/socket.c:2489 ___sys_sendmsg+0xf3/0x170 net/socket.c:2543 __sys_sendmsg net/socket.c:2572 [inline] __do_sys_sendmsg net/socket.c:2581 [inline] __se_sys_sendmsg net/socket.c:2579 [inline] __x64_sys_sendmsg+0x132/0x220 net/socket.c:2579 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7f3baaa89109 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f3babba9168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f3baab9bf60 RCX: 00007f3baaa89109 RDX: 0000000000000000 RSI: 0000000020000a00 RDI: 0000000000000003 RBP: 00007f3baaae305d R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffe74f2543f R14: 00007f3babba9300 R15: 0000000000022000 </TASK> Fixes: 4cb47a86 ("tunnels: PMTU discovery support for directly bridged IP packets") Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Stefano Brivio <sbrivio@redhat.com> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
- 24 Jun, 2022 12 commits
-
-
Dan Carpenter authored
The "1<<31" shift has a sign extension bug so IFF_TX_SKB_NO_LINEAR is 0xffffffff80000000 instead of 0x0000000080000000. Fixes: c2ff53d8 ("net: Add priv_flags for allow tx skb without linear") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Xuan Zhuo <xuanzhuo@linux.alibaba.com> Link: https://lore.kernel.org/r/YrRrcGttfEVnf85Q@kiliSigned-off-by:
-
Jakub Kicinski authored
Enguerrand de Ribaucourt says: ==================== net: dp83822: fix interrupt floods The false carrier and RX error counters, once half full, produce interrupt floods. Since we do not use these counters, these interrupts should be disabled. ==================== Link: https://lore.kernel.org/r/20220623134645.1858361-1-enguerrand.de-ribaucourt@savoirfairelinux.comSigned-off-by:
-
Enguerrand de Ribaucourt authored
Some RX errors, notably when disconnecting the cable, increase the RCSR register. Once half full (0x7fff), an interrupt flood is generated. I measured ~3k/s interrupts even after the RX errors transfer was stopped. Since we don't read and clear the RCSR register, we should disable this interrupt. Fixes: 87461f7a ("net: phy: DP83822 initial driver submission") Signed-off-by:
Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Enguerrand de Ribaucourt authored
When unplugging an Ethernet cable, false carrier events were produced by the PHY at a very high rate. Once the false carrier counter full, an interrupt was triggered every few clock cycles until the cable was replugged. This resulted in approximately 10k/s interrupts. Since the false carrier counter (FCSCR) is never used, we can safely disable this interrupt. In addition to improving performance, this also solved MDIO read timeouts I was randomly encountering with an i.MX8 fec MAC because of the interrupt flood. The interrupt count and MDIO timeout fix were tested on a v5.4.110 kernel. Fixes: 87461f7a ("net: phy: DP83822 initial driver submission") Signed-off-by:
-
Jakub Kicinski authored
Syzbot found a race between tun file and device destruction. NAPIs live in struct tun_file which can get destroyed before the netdev so we have to del them explicitly. The current code is missing deleting the NAPI if the queue was detached first. Fixes: 94317099 ("tun: enable NAPI for TUN/TAP driver") Reported-by: syzbot+b75c138e9286ac742647@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20220623042039.2274708-1-kuba@kernel.orgSigned-off-by:
-
Eric Dumazet authored
When the third packet of 3WHS connection establishment contains payload, it is added into socket receive queue without the XFRM check and the drop of connection tracking context. This means that if the data is left unread in the socket receive queue, conntrack module can not be unloaded. As most applications usually reads the incoming data immediately after accept(), bug has been hiding for quite a long time. Commit 68822bdf ("net: generalize skb freeing deferral to per-cpu lists") exposed this bug because even if the application reads this data, the skb with nfct state could stay in a per-cpu cache for an arbitrary time, if said cpu no longer process RX softirqs. Many thanks to Ilya Maximets for reporting this issue, and for testing various patches: https://lore.kernel.org/netdev/20220619003919.394622-1-i.maximets@ovn.org/ Note that I also added a missing xfrm4_policy_check() call, although this is probably not a big issue, as the SYN packet should have been dropped earlier. Fixes: b59c2701 ("[NETFILTER]: Keep conntrack reference until IPsec policy checks are done") Reported-by:
Ilya Maximets <i.maximets@ovn.org> Signed-off-by:
-
Jakub Sitnicki authored
Cover the scenario when we cannot insert a socket into the sockmap, because it has it is using ULP. Failed insert should not have any effect on the ULP state. This is a regression test. Signed-off-by:
Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/r/20220623091231.417138-1-jakub@cloudflare.comSigned-off-by:
-
Dimitris Michailidis authored
udpgso_bench.sh has been running its IPv6 TCP test with IPv4 arguments since its initial conmit. Looks like a typo. Fixes: 3a687bef ("selftests: udp gso benchmark") Cc: willemb@google.com Signed-off-by:
Dimitris Michailidis <dmichail@fungible.com> Acked-by:
Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20220623000234.61774-1-dmichail@fungible.comSigned-off-by:
-
Eric Dumazet authored
syzbot reported uninit-value in tcp_recvmsg() [1] Issue here is that msg->msg_get_inq should have been cleared, otherwise tcp_recvmsg() might read garbage and perform more work than needed, or have undefined behavior. Given CONFIG_INIT_STACK_ALL_ZERO=y is probably going to be the default soon, I chose to change __sys_recvfrom() to clear all fields but msghdr.addr which might be not NULL. For __copy_msghdr_from_user(), I added an explicit clear of kmsg->msg_get_inq. [1] BUG: KMSAN: uninit-value in tcp_recvmsg+0x6cf/0xb60 net/ipv4/tcp.c:2557 tcp_recvmsg+0x6cf/0xb60 net/ipv4/tcp.c:2557 inet_recvmsg+0x13a/0x5a0 net/ipv4/af_inet.c:850 sock_recvmsg_nosec net/socket.c:995 [inline] sock_recvmsg net/socket.c:1013 [inline] __sys_recvfrom+0x696/0x900 net/socket.c:2176 __do_sys_recvfrom net/socket.c:2194 [inline] __se_sys_recvfrom net/socket.c:2190 [inline] __x64_sys_recvfrom+0x122/0x1c0 net/socket.c:2190 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Local variable msg created at: __sys_recvfrom+0x81/0x900 net/socket.c:2154 __do_sys_recvfrom net/socket.c:2194 [inline] __se_sys_recvfrom net/socket.c:2190 [inline] __x64_sys_recvfrom+0x122/0x1c0 net/socket.c:2190 CPU: 0 PID: 3493 Comm: syz-executor170 Not tainted 5.19.0-rc3-syzkaller-30868-g4b28366af7d9 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: f94fd25c ("tcp: pass back data left in socket after receive") Reported-by:
Jens Axboe <axboe@kernel.dk> Tested-by: Alexander Potapenko<glider@google.com> Link: https://lore.kernel.org/r/20220622150220.1091182-1-edumazet@google.comSigned-off-by:
-
Krzysztof Kozlowski authored
"mlx" Devicetree vendor prefix is not documented and instead "mellanox" should be used. Signed-off-by:
-
Doug Berger authored
The pause settings reported by the PHY should also be applied to the GMII port status override otherwise the switch will not generate pause frames towards the link partner despite the advertisement saying otherwise. Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by:
Doug Berger <opendmb@gmail.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220623030204.1966851-1-f.fainelli@gmail.comSigned-off-by:
-
Liang He authored
of_find_node_by_name() will decrease the refcount of its first arg and we need a of_node_get() to keep refcount balance. Fixes: 7d9ee2e8 ("net: dsa: hellcreek: Add PTP status LEDs") Signed-off-by:
Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220622040621.4094304-1-windhl@126.comSigned-off-by:
-
- 23 Jun, 2022 12 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Paolo Abeni: "Including fixes from bpf and netfilter. Current release - regressions: - netfilter: cttimeout: fix slab-out-of-bounds read in cttimeout_net_exit Current release - new code bugs: - bpf: ftrace: keep address offset in ftrace_lookup_symbols - bpf: force cookies array to follow symbols sorting Previous releases - regressions: - ipv4: ping: fix bind address validity check - tipc: fix use-after-free read in tipc_named_reinit - eth: veth: add updating of trans_start Previous releases - always broken: - sock: redo the psock vs ULP protection check - netfilter: nf_dup_netdev: fix skb_under_panic - bpf: fix request_sock leak in sk lookup helpers - eth: igb: fix a use-after-free issue in igb_clean_tx_ring - eth: ice: prohibit improper channel config for DCB - eth: at803x: fix null pointer dereference on AR9331 phy - eth: virtio_net: fix xdp_rxq_info bug after suspend/resume Misc: - eth: hinic: replace memcpy() with direct assignment" * tag 'net-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits) net: openvswitch: fix parsing of nw_proto for IPv6 fragments sock: redo the psock vs ULP protection check Revert "net/tls: fix tls_sk_proto_close executed repeatedly" virtio_net: fix xdp_rxq_info bug after suspend/resume igb: Make DMA faster when CPU is active on the PCIe link net: dsa: qca8k: reduce mgmt ethernet timeout net: dsa: qca8k: reset cpu port on MTU change MAINTAINERS: Add a maintainer for OCP Time Card hinic: Replace memcpy() with direct assignment Revert "drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c" net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode ice: ethtool: Prohibit improper channel config for DCB ice: ethtool: advertise 1000M speeds properly ice: Fix switchdev rules book keeping ice: ignore protocol field in GTP offload netfilter: nf_dup_netdev: add and use recursion counter netfilter: nf_dup_netdev: do not push mac header a second time selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh net/tls: fix tls_sk_proto_close executed repeatedly erspan: do not assume transport header is always set ... -
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds authored
Pull MMC fixes from Ulf Hansson: - mtk-sd: Fix dma hang issues - sdhci-pci-o2micro: Fix card detect by dealing with debouncing * tag 'mmc-v5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: mediatek: wait dma stop bit reset to 0 mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds authored
Pull sound fixes from Takashi Iwai: "All small changes, mostly device-specific: - A regression fix for PCM WC-page allocation on x86 - A regression fix for i915 audio component binding - Fixes for (longstanding) beep handling bug - Runtime PM fixes for Intel LPE HDMI audio - A couple of pending FireWire fixes - Usual HD-audio and USB-audio quirks, new Intel dspconf entries" * tag 'sound-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda/realtek: Add quirk for Clevo NS50PU ALSA: hda: Fix discovery of i915 graphics PCI device ALSA: hda/via: Fix missing beep setup ALSA: hda/conexant: Fix missing beep setup ALSA: memalloc: Drop x86-specific hack for WC allocations ALSA: hda/realtek: Add quirk for Clevo PD70PNT ALSA: x86: intel_hdmi_audio: use pm_runtime_resume_and_get() ALSA: x86: intel_hdmi_audio: enable pm_runtime and set autosuspend delay ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg ALSA: hda: intel-dspcfg: use SOF for UpExtreme and UpExtreme11 boards firewire: convert sysfs sprintf/snprintf family to sysfs_emit firewire: cdev: fix potential leak of kernel stack due to uninitialized value ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly ALSA: hda/realtek - ALC897 headset MIC no sound ALSA: usb-audio: US16x08: Move overflow check before array access ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop
-
Rosemarie O'Riorden authored
When a packet enters the OVS datapath and does not match any existing flows installed in the kernel flow cache, the packet will be sent to userspace to be parsed, and a new flow will be created. The kernel and OVS rely on each other to parse packet fields in the same way so that packets will be handled properly. As per the design document linked below, OVS expects all later IPv6 fragments to have nw_proto=44 in the flow key, so they can be correctly matched on OpenFlow rules. OpenFlow controllers create pipelines based on this design. This behavior was changed by the commit in the Fixes tag so that nw_proto equals the next_header field of the last extension header. However, there is no counterpart for this change in OVS userspace, meaning that this field is parsed differently between OVS and the kernel. This is a problem because OVS creates actions based on what is parsed in userspace, but the kernel-provided flow key is used as a match criteria, as described in Documentation/networking/openvswitch.rst. This leads to issues such as packets incorrectly matching on a flow and thus the wrong list of actions being applied to the packet. Such changes in packet parsing cannot be implemented without breaking the userspace. The offending commit is partially reverted to restore the expected behavior. The change technically made sense and there is a good reason that it was implemented, but it does not comply with the original design of OVS. If in the future someone wants to implement such a change, then it must be user-configurable and disabled by default to preserve backwards compatibility with existing OVS versions. Cc: stable@vger.kernel.org Fixes: fa642f08 ("openvswitch: Derive IP protocol number for IPv6 later frags") Link: https://docs.openvswitch.org/en/latest/topics/design/#fragmentsSigned-off-by:
Rosemarie O'Riorden <roriorden@redhat.com> Acked-by:
Eelco Chaudron <echaudro@redhat.com> Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Jakub Kicinski authored
Commit 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()") has moved the inet_csk_has_ulp(sk) check from sk_psock_init() to the new tcp_bpf_update_proto() function. I'm guessing that this was done to allow creating psocks for non-inet sockets. Unfortunately the destruction path for psock includes the ULP unwind, so we need to fail the sk_psock_init() itself. Otherwise if ULP is already present we'll notice that later, and call tcp_update_ulp() with the sk_proto of the ULP itself, which will most likely result in the ULP looping its callbacks. Fixes: 8a59f9d1 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()") Signed-off-by:
John Fastabend <john.fastabend@gmail.com> Reviewed-by:
-
Jakub Kicinski authored
This reverts commit 69135c57. This commit was just papering over the issue, ULP should not get ->update() called with its own sk_prot. Each ULP would need to add this check. Fixes: 69135c57 ("net/tls: fix tls_sk_proto_close executed repeatedly") Signed-off-by:
-
Stephan Gerhold authored
The following sequence currently causes a driver bug warning when using virtio_net: # ip link set eth0 up # echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem) <resume> # ip link set eth0 down Missing register, driver bug WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60 Call trace: xdp_rxq_info_unreg+0x58/0x60 virtnet_close+0x58/0xac __dev_close_many+0xac/0x140 __dev_change_flags+0xd8/0x210 dev_change_flags+0x24/0x64 do_setlink+0x230/0xdd0 ... This happens because virtnet_freeze() frees the receive_queue completely (including struct xdp_rxq_info) but does not call xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the receive_queue again but does not call xdp_rxq_info_reg(). Actually, parts of virtnet_freeze_down() and virtnet_restore_up() are almost identical to virtnet_close() and virtnet_open(): only the calls to xdp_rxq_info_(un)reg() are missing. This means that we can fix this easily and avoid such problems in the future by just calling virtnet_close()/open() from the freeze/restore handlers. Aside from adding the missing xdp_rxq_info calls the only difference is that the refill work is only cancelled if netif_running(). However, this should not make any functional difference since the refill work should only be active if the network interface is actually up. Fixes: 754b8a21 ("virtio_net: setup xdp_rxq_info") Signed-off-by:
Stephan Gerhold <stephan.gerhold@kernkonzept.com> Acked-by:
Jesper Dangaard Brouer <brouer@redhat.com> Acked-by:
Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2022-06-21 This series contains updates to ice driver only. Marcin fixes GTP filters by allowing ignoring of the inner ethertype field. Wojciech adds VSI handle tracking in order to properly distinguish similar filters for removal. Anatolii removes ability to set 1000baseT and 1000baseX fields concurrently which caused link issues. He also disallows setting channels to less than the number of Traffic Classes which would cause NULL pointer dereference. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: ethtool: Prohibit improper channel config for DCB ice: ethtool: advertise 1000M speeds properly ice: Fix switchdev rules book keeping ice: ignore protocol field in GTP offload ==================== Link: https://lore.kernel.org/r/20220621224756.631765-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Kai-Heng Feng authored
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which will be significantly lower when 1) ASPM is disabled or 2) SoC package c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx speed can reach to ~950Mbps. According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC", "DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so set it to 1b for "DMA is considered idle when there is no Rx or Tx AND when there are no TLPs indicating that CPU is active detected on the PCIe link (such as the host executes CSR or Configuration register read or write operation)" and performing Tx should also fall under "active CPU on PCIe link" case. In addition to that, commit b6e0c419 ("igb: Move DMA Coalescing init code to separate function.") seems to wrongly changed from enabling E1000_PCIEMISC_LX_DECISION to disabling it, also fix that. Fixes: b6e0c419 ("igb: Move DMA Coalescing init code to separate function.") Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Christian Marangi authored
The current mgmt ethernet timeout is set to 100ms. This value is too big and would slow down any mdio command in case the mgmt ethernet packet have some problems on the receiving part. Reduce it to just 5ms to handle case when some operation are done on the master port that would cause the mgmt ethernet to not work temporarily. Fixes: 5950c7c0 ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet") Signed-off-by:
Christian Marangi <ansuelsmth@gmail.com> Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.comSigned-off-by:
-
Christian Marangi authored
It was discovered that the Documentation lacks of a fundamental detail on how to correctly change the MAX_FRAME_SIZE of the switch. In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the switch panics and cease to send any packet. This cause the mgmt ethernet system to not receive any packet (the slow fallback still works) and makes the device not reachable. To recover from this a switch reset is required. To correctly handle this, turn off the cpu ports before changing the MAX_FRAME_SIZE and turn on again after the value is applied. Fixes: f58d2598 ("net: dsa: qca8k: implement the port MTU callbacks") Cc: stable@vger.kernel.org Signed-off-by:
-
Vadim Fedorenko authored
I've been contributing and reviewing patches for ptp_ocp driver for some time and I'm taking care of it's github mirror. On Jakub's suggestion, I would like to step forward and become a maintainer for this driver. This patch adds a dedicated entry to MAINTAINERS. Signed-off-by:
Vadim Fedorenko <vadfed@fb.com> Acked-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Link: https://lore.kernel.org/r/20220621233131.21240-1-vfedorenko@novek.ruSigned-off-by:
-
- 22 Jun, 2022 5 commits
-
-
Linus Torvalds authored
Merge tag 'linux-kselftest-fixes-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest Pull Kselftest fixes from Shuah Khan: "Compile time fixes and run-time resources leaks: - Fix clang cross compilation - Fix resource leak when return error - fix compile error for dma_map_benchmark - Fix regression - make use of GUP_TEST_FILE macro" * tag 'linux-kselftest-fixes-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: selftests: make use of GUP_TEST_FILE macro selftests: vm: Fix resource leak when return error selftests dma: fix compile error for dma_map_benchmark selftests: Fix clang cross compilation
-
Kees Cook authored
Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged here for calculating the size of the destination buffer (0x10 instead of 0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with the source and dest being struct fw_section_info_st, so the memcpy should be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's responsibility to figure out. Avoid the whole thing and just do a direct assignment. This results in no change to the executable code. [This is a duplicate of commit 2c0ab32b ("hinic: Replace memcpy() with direct assignment") which was applied to net-next.] Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Tom Rix <trix@redhat.com> Cc: llvm@lists.linux.dev Link: https://github.com/ClangBuiltLinux/linux/issues/1592Signed-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> # build Link: https://lore.kernel.org/r/20220616052312.292861-1-keescook@chromium.orgSigned-off-by:
-
Tim Crawford authored
Fixes headset detection on Clevo NS50PU. Signed-off-by:
Tim Crawford <tcrawford@system76.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220622150017.9897-1-tcrawford@system76.comSigned-off-by:
Takashi Iwai <tiwai@suse.de>
-
https://github.com/martinetd/linuxLinus Torvalds authored
Pull 9pfs fixes from Dominique Martinet: "A couple of fid refcount and fscache fixes: - fid refcounting was incorrect in some corner cases and would leak resources, only freed at umount time. The first three commits fix three such cases - 'cache=loose' or fscache was broken when trying to write a partial page to a file with no read permission since the rework a few releases ago. The fix taken here is just to restore old behavior of using the special 'writeback_fid' for such reads, which is open as root/RDWR and such not get complains that we try to read on a WRONLY fid. Long-term it'd be nice to get rid of this and not issue the read at all (skip cache?) in such cases, but that direction hasn't progressed" * tag '9p-for-5.19-rc4' of https://github.com/martinetd/linux: 9p: fix EBADF errors in cached mode 9p: Fix refcounting during full path walks for fid lookups 9p: fix fid refcount leak in v9fs_vfs_get_link 9p: fix fid refcount leak in v9fs_vfs_atomic_open_dotl -
Jakub Kicinski authored
This reverts commit 8fc74d18. BAR0 is the main (only?) register bank for this device. We most obviously can't unmap it before the netdev is unregistered. This was pointed out in review but the patch got reposted and merged, anyway. The author of the patch was only testing it with a QEMU model, which I presume does not emulate enough for the netdev to be brought up (author's replies are not visible in lore because they kept sending their emails in HTML). Link: https://lore.kernel.org/all/20220616085059.680dc215@kernel.org/ Fixes: 8fc74d18 ("drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c") Signed-off-by:
-
