Arnd reported the following build bug bug:

In file included from arch/arm/mach-sa1100/simpad.c:20:0:
arch/arm/mach-sa1100/include/mach/SA-1100.h:1118:18: error: large
integer implicitly truncated to unsigned type [-Werror=overflow]
                      (0x00000001 << (Nb))
                      ^
include/linux/gpio/machine.h:56:16: note: in definition of macro
'GPIO_LOOKUP_IDX'
.chip_hwnum = _chip_hwnum,
              ^~~~~~~~~~~
arch/arm/mach-sa1100/include/mach/SA-1100.h:1140:21: note: in
expansion of macro 'GPIO_GPIO'
                    ^~~~~~~~~
arch/arm/mach-sa1100/simpad.c:331:27: note: in expansion of
macro 'GPIO_GPIO21'
  GPIO_LOOKUP_IDX("gpio", GPIO_GPIO21, NULL, 0,

This is what happened:

commit b2e63555
"i2c: gpio: Convert to use descriptors"
commit 4d0ce62c
"i2c: gpio: Augment all boardfiles to use open drain"
together uncovered an old bug in the Simpad board
file: as theGPIO_LOOKUP_IDX() encodes GPIO offsets
on gpiochips in an u16 (see <linux/gpio/machine.h>)
these GPIO "numbers" does not fit, since in
arch/arm/mach-sa1100/include/mach/SA-1100.h it is
defined as:

  #define GPIO_GPIO(Nb) (0x00000001 << (Nb))
  (...)
  #define GPIO_GPIO21 GPIO_GPIO(21) /* GPIO [21] */

This is however provably wrong, since the i2c-gpio
driver uses proper GPIO numbers, albeit earlier from
the global number space, whereas this GPIO_GPIO21
is the local line offset in the GPIO register, which
is used in other code but certainly not in the
gpiolib GPIO driver in drivers/gpio/gpio-sa1100.c, which
has code like this:

static void sa1100_gpio_set(struct gpio_chip *chip,
                            unsigned offset, int value)
{
    int reg = value ? R_GPSR : R_GPCR;

    writel_relaxed(BIT(offset),
        sa1100_gpio_chip(chip)->membase + reg);
}

So far everything however compiled fine as an unsigned
int was used to pass the GPIO numbers in
struct i2c_gpio_platform_data. We can trace the actual error
back to

commit dbd406f9
"ARM: 7025/1: simpad: add GPIO based device definitions."
This added the i2c_gpio with the wrong offsets.

This commit was before the SA1100 was converted to use
the gpiolib, but as can be seen from the contemporary
gpio.c in mach-sa1100, it was already using:

static int sa1100_gpio_get(struct gpio_chip *chip,
                           unsigned offset)
{
        return GPLR & GPIO_GPIO(offset);
}

And GPIO_GPIO() is essentially the BIT() macro.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In order to use i2c from a cold boot, the i2c peripheral must be taken
out of reset. We request a shared reset controller each time a bus
driver is loaded, as the reset is shared between the 14 i2c buses.

On remove the reset is asserted, which only touches the hardware once
the last i2c bus is removed.

The reset is required as the I2C buses will not work without releasing
the reset. Previously the driver only worked with out of tree hacks
that released this reset before the driver was loaded. Update the
device tree bindings to reflect this.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.

But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.

To maintain backward compatibility with old Device Trees, only use the OF
device ID table .data if the device was registered via OF and the OF node
compatible matches an entry in the OF device ID table.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Bartosz agreed to take over maintainership from me. Thank you very much
and good luck and have fun! :)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>

Commit 7da62cb1 ("i2c: nuc900: remove driver") removed the driver,
we should remove the platform_data as well.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

It's a common pattern to be NULL-aware when freeing resources.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch supports xgene-slimpro-i2c v2 which uses the non-cachable memory
as the PCC shared memory.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

cppcheck rightfully says:

drivers/i2c/busses/i2c-mpc.c:329: style: Variable 'node' is reassigned a value before the old one has been used.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Merge branch 'for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into i2c/for-4.15

Refactor i2c-gpio and its users to use gpiod. Done by GPIO maintainer
LinusW.

A very conservative check for bus activity (to prevent interference
in multimaster setups) prevented the bus recovery methods from being
triggered in the case that SDA or SCL was stuck low.
This defeats the purpose of the recovery mechanism, which was introduced
for exactly this situation (a slave device keeping SDA pulled down).

Also added a check to make sure SDA is low before attempting recovery.
If SDA is not stuck low, recovery will not help, so we can skip it.

Note that bus lockups can persist across reboots. The only other options
are to reset or power cycle the offending slave device, and many i2c
slaves do not even have a reset pin.

If we see that one of the lines is low for the entire timeout duration,
we can actually be sure that there is no other master driving the bus.
It is therefore save for us to attempt a bus recovery.
Signed-off-by: Claudio Foellmi <claudio.foellmi@ergon.ch>
Tested-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
[wsa: fixed one return code to -EBUSY]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This adds support for using the "sda" and "scl" GPIOs in
device tree instead of anonymously using index 0 and 1 of
the "gpios" property.

We add a helper function to retrieve the GPIO descriptors
and some explicit error handling since the probe may have
to be deferred. At least this happened to me when moving
to using named "sda" and "scl" lines (all of a sudden this
started to probe before the GPIO driver) so we need to
gracefully defer probe when we ge -ENOENT in the error
pointer.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The current i2c-gpio DT bindings use a single unnamed "gpios" property
to refer to the SDA and SCL signal lines by index.  This is error-prone
for the casual DT writer and reviewer, as one has to look up the order
in the DT bindings.

Fix this by amending the DT bindings to use two separate named gpios
properties, and deprecate the old unnamed variant.

Take this opportunity to clearly deprecate the "i2c-gpio,sda-open-drain"
and "i2c-gpio,scl-open-drain" flags as well. The commit describes
in detail what these flags actually mean, and why they should not be
used in new device trees.

Cc: devicetree@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[Augmented to what I and Rob would like]
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

By creating local variables for *dev and *np, the code become
much easier to read, in my opinion.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We now handle the open drain mode internally in the I2C GPIO
driver, but we will get warnings from the gpiolib that we
override the default mode of the line so it becomes open
drain.

We can fix all in-kernel users by simply passing the right
flag along in the descriptor table, and we already touched
all of these files in the series so let's just tidy it up.

Cc: Steven Miao <realmz6@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Wu, Aaron <Aaron.Wu@analog.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The I2C GPIO bitbang driver currently emulates open drain
behaviour by implementing what the gpiolib already does:
not actively driving the line high, instead setting it to
input.

This makes no sense. Use the new facility in gpiolib to
request the lines enforced into open drain mode, and let
the open drain emulation already present in the gpiolib
kick in and handle this.

As a bonus: if the GPIO driver in the back-end actually
supports open drain in hardware using the .set_config()
callback, it will be utilized. That's correct: we never
used that hardware feature before, instead relying on
emulating open drain even if the GPIO controller could
actually handle this for us.

Users will sometimes get messages like this:
gpio-485 (?): enforced open drain please flag it properly
  in DT/ACPI DSDT/board file
gpio-486 (?): enforced open drain please flag it properly
  in DT/ACPI DSDT/board file
i2c-gpio gpio-i2c: using lines 485 (SDA) and 486 (SCL)

Which is completely proper: since the line is used as
open drain, it should actually be flagged properly with
e.g.

gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>,
        <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;

Or similar facilities in board file descriptor tables
or ACPI DSDT.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some busses, like I2C, strictly need to have the line handled
as open drain, i.e. not actively driven high. For this reason
the i2c-gpio.c bit-banged I2C driver is reimplementing open
drain handling outside of gpiolib.

This is not very optimal. Instead make it possible for a
consumer to explcitly express that the line must be handled
as open drain instead of allowing local hacks papering over
this issue.

The descriptor tables, whether DT, ACPI or board files, should
of course have flagged these lines as open drain. E.g.:
enum gpio_lookup_flags GPIO_OPEN_DRAIN for a board file, or
gpios = <&foo 42 GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN>; in a
device tree using <dt-bindings/gpio/gpio.h>

But more often than not, these descriptors are wrong. So
we need to make it possible for consumers to enforce this
open drain behaviour.

We now have two new enumerated GPIO descriptor config flags:
GPIOD_OUT_LOW_OPEN_DRAIN and GPIOD_OUT_HIGH_OPEN_DRAIN
that will set up the lined enforced as open drain as output
low or high, using open drain (if the driver supports it)
or using open drain emulation (setting the line as input
to drive it high) from the gpiolib core.

Cc: linux-gpio@vger.kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This converts the GPIO-based I2C-driver to using GPIO
descriptors instead of the old global numberspace-based
GPIO interface. We:

- Convert the driver to unconditionally grab two GPIOs
  from the device by index 0 (SDA) and 1 (SCL) which
  will work fine with device tree and descriptor tables.
  The existing device trees will continue to work just
  like before, but without any roundtrip through the
  global numberspace.

- Brutally convert all boardfiles still passing global
  GPIOs by registering descriptor tables associated with
  the devices instead so this driver does not need to keep
  supporting passing any GPIO numbers as platform data.

There is no stepwise approach as elegant as this, I
strongly prefer this big hammer over any antsteps for this
conversion. This way the old GPIO numbers go away and
NEVER COME BACK.

Special conversion for the different boards utilizing
I2C-GPIO:

- EP93xx (arch/arm/mach-ep93xx): pretty straight forward as
  all boards were using the same two GPIO lines, just define
  these two in a lookup table for "i2c-gpio" and register
  these along with the device. None of them define any
  other platform data so just pass NULL as platform data.
  This platform selects GPIOLIB so all should be smooth.
  The pins appear on a gpiochip for bank "G" as pins 1 (SDA)
  and 0 (SCL).

- IXP4 (arch/arm/mach-ixp4): descriptor tables have to
  be registered for each board separately. They all use
  "IXP4XX_GPIO_CHIP" so it is pretty straight forward.
  Most board define no other platform data than SCL/SDA
  so they can drop the #include of <linux/i2c-gpio.h> and
  assign NULL to platform data.

  The "goramo_mlr" (Goramo Multilink Router) board is a bit
  worrisome: it implements its own I2C bit-banging in the
  board file, and optionally registers an I2C serial port,
  but claims the same GPIO lines for itself in the board file.
  This is not going to work: there will be competition for the
  GPIO lines, so delete the optional extra I2C bus instead, no
  I2C devices are registered on it anyway, there are just hints
  that it may contain an EEPROM that may be accessed from
  userspace. This needs to be fixed up properly by the serial
  clock using I2C emulation so drop a note in the code.

- KS8695 board acs5k (arch/arm/mach-ks8695/board-acs5.c)
  has some platform data in addition to the pins so it needs to
  be kept around sans GPIO lines. Its GPIO chip is named
  "KS8695" and the arch selects GPIOLIB.

- PXA boards (arch/arm/mach-pxa/*) use some of the platform
  data so it needs to be preserved here. The viper board even
  registers two GPIO I2Cs. The gpiochip is named "gpio-pxa" and
  the arch selects GPIOLIB.

- SA1100 Simpad (arch/arm/mach-sa1100/simpad.c) defines a GPIO
  I2C bus, and the arch selects GPIOLIB.

- Blackfin boards (arch/blackfin/bf533 etc) for these I assume
  their I2C GPIOs refer to the local gpiochip defined in
  arch/blackfin/kernel/bfin_gpio.c names "BFIN-GPIO".
  The arch selects GPIOLIB. The boards get spiked with
  IF_ENABLED(I2C_GPIO) but that is a side effect of it
  being like that already (I would just have Kconfig select
  I2C_GPIO and get rid of them all.) I also delete any
  platform data set to 0 as it will get that value anyway
  from static declartions of platform data.

- The MIPS selects GPIOLIB and the Alchemy machine is using
  two local GPIO chips, one of them has a GPIO I2C. We need
  to adjust the local offset from the global number space here.
  The ATH79 has a proper GPIO driver in drivers/gpio/gpio-ath79.c
  and AFAICT the chip is named "ath79-gpio" and the PB44
  PCF857x expander spawns from this on GPIO 1 and 0. The latter
  board only use the platform data to specify pins so it can be
  cut altogether after this.

- The MFD Silicon Motion SM501 is a special case. It dynamically
  spawns an I2C bus off the MFD using sm501_create_subdev().
  We use an approach to dynamically create a machine descriptor
  table and attach this to the "SM501-LOW" or "SM501-HIGH"
  gpiochip. We use chip-local offsets to grab the right lines.
  We can get rid of two local static inline helpers as part
  of this refactoring.

Cc: Steven Miao <realmz6@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Wu, Aaron <Aaron.Wu@analog.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use 'unsigned int' and curly braces for 'else'.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Since the return value is not checked anyhow, we don't need to store it.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Those variables are immediately assigned a value afterwards.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently when a gpio is defined for battery presence it is only used in
the sbs_get_battery_presence_and_health function for 2 properties.
All other properties currently try to read data form the battery before
returning an error if not present. We should know in advance that no
data is going to returned.

As the driver tries multiple times to access a property, this prevents
a lot of smbus accesses, which had a significant effect on device boot-up.
As when the device is registered lots of property accesses are attempted
during boot.

If no gpio is used for presence detection no change in behaviour should
occur.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This adds smb alert support via the smbus_alert driver to generate
power_supply_changed notifications when either external power is
removed / applied or a battery inserted / removed.
Use the i2c alert callback to notify the attached battery driver that a
change has occurred.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch adds support for Smart Battery System Manager.
A SBSM is a device listening at I2C/SMBus address 0x0a and is capable of
communicating up to four I2C smart battery devices. All smart battery
devices are listening at address 0x0b, so the SBSM muliplexes between
them. The driver makes use of the I2C-Mux framework to allow smart
batteries to be bound via device tree, i.e. the sbs-battery driver.

Via sysfs interface the online state and charge type are presented. If
the driver is bound as ltc1760 (an implementation of a Dual Smart Battery
System Manager) the charge type can also be changed from trickle to fast.
Signed-off-by: Karl-Heinz Schneider <karl-heinz@schneider-inet.de>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch adds device tree documentation for the sbs-manager
Signed-off-by: Karl-Heinz Schneider <karl-heinz@schneider-inet.de>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

irq_create_mapping can return an error, report error to log and return.
Cleanup will occur in the probe function when an error is returned.
Suggested-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The pca954x device do not have the ability to mask interrupts. For
i2c slave devices that also don't have masking ability (eg ltc1760
smbalert output) delay registering the irq until after the mux
segments have been configured. During the mux add_adaptor call the
core i2c system can register an smbalert handler which would then
be called immediately when the irq is registered. This smbalert
handler will then clear the pending irq.

This removes the need for the irq_mask / irq_unmask calls that were
original used to do this.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add a call to of_i2c_setup_smbus_alert when a i2c adapter is registered
so the the smbalert driver can be registered.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This commit adds of_i2c_setup_smbus_alert which allows the smbalert
driver to be attached to an i2c adapter via the device tree.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In preparation to adding of_i2c_setup_smbus_alert() move
i2c_setup_smbus_alert() to core module. of_i2c_setup_smbus_alert()
will call i2c_setup_smbus_alert() and this avoid module dependecy issues.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Prior to this commit the smbalert_irq was handling in the hard irq
context. This change switch to using a thread irq which avoids the need
for the work thread. Using threaded irq also removes the need for the
edge_triggered flag as the enabling / disabling of the hard irq for level
triggered interrupts will be handled by the irq core.

Without this change have an irq connected to something like an i2c gpio
resulted in a null ptr deferences. Specifically handle_nested_irq calls
the threaded irq handler.

There are currently 3 in tree drivers affected by this change.

i2c-parport driver calls i2c_handle_smbus_alert in a hard irq context.
This driver use edge trigger interrupts which skip the enable / disable
calls. But it still need to handle the smbus transaction on a thread. So
the work thread is kept for this driver.

i2c-parport-light & i2c-thunderx-pcidrv provide the irq number in the
setup which will result in the thread irq being used.

i2c-parport-light is edge trigger so the enable / disable call was
skipped as well.

i2c-thunderx-pcidrv is getting the edge / level trigger setting from of
data and was setting the flag as required. However the irq core should
handle this automatically.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Move the check for a stuck SCL before the check for a high SDA.
This prevent false positives in the specific case that SDA is fine
and SCL is stuck, which previously returned 0.

Also check SDA again after the loop, if we can.
Together, these changes should lead to a lot more failed
recoveries being caught and returning error codes.
Signed-off-by: Claudio Foellmi <claudio.foellmi@ergon.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This trivial patch managed to fall through the cracks and was forgotten
in the first pull request, as noticed by Wolfram.

The i2c-img-scb driver already dynamically enables / disables clocks to
save power, but doesn't use the runtime PM framework. Convert the
driver to use runtime PM, so that dynamic clock management will be
disabled when runtime PM is disabled, and so that autosuspend can be
used to avoid unnecessarily disabling and re-enabling clocks repeatedly
during a sequence of transactions.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fix both instances.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Peter Rosin <peda@axentia.se>

Use of_property_read_bool to check for the existence of a property.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Remove the restriction that the parent clock has to be a specific frequency
and also allow any speed to be supported.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>