Upstream commit 98d74f9c ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.

The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.

The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".

Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 04abb6de ("xhci: Read and parse new xhci
	1.1 capability register")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

because hcd_priv_size is already size of xhci_hcd struct,
extra_priv_size is not needed anymore for MTK and tegra drivers.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hcc_params is set in xhci_gen_setup() called from usb_add_hcd(),
so checks the Maximum Primary Stream Array Size in the hcc_params
register after adding primary hcd.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v4.11-rc2

Here's a fix for a digi_acceleport regression in -rc1, and some fixes
for long-standing issues in three other drivers, including a
NULL-pointer dereference and a couple of information leaks that could be
triggered by a malicious device.
Signed-off-by: Johan Hovold <johan@kernel.org>

A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.

Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d380889 ("USB: serial: digi_acceleport: fix OOB data sanity check")
Cc: stable <stable@vger.kernel.org>	# v2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The platform_data header file was dropped in the merged version of the
USB251xB driver. Therefore remove its reference from the MAINTAINERS file.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Mark the reg property as required and furthermore fix some typos and
spellings in the documentation.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename oc-delay-* to oc-delay-us and make it expect a time value.
Furthermore add -ms suffix to power-on-time. There changes were
suggested by Rob Herring in https://lkml.org/lkml/2017/2/15/1283.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This USB-SATA bridge chip is used in a StarTech enclosure for
optical drives.

Without the quirk MakeMKV fails during the key exchange with an
installed BluRay drive:
> Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
> occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:2'
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.

Fixes: 946b960d ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org>     # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to check for the required interrupt-in endpoint to avoid
dereferencing a NULL-pointer should a malicious device lack such an
endpoint.

Note that a fairly recent change purported to fix this issue, but added
an insufficient test on the number of endpoints only, a test which can
now be removed.

Fixes: 4ec0ef3a ("USB: iowarrior: fix oops with malicious USB descriptors")
Fixes: 946b960d ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org>	# 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.

But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In patch 2e2aa1bcm, USB suspend and wakeup control requests are
passed to SFR_OHCIICR register. If a processor does not have such a
register, this hub control request will be dropped.

If no such a SFR register is available, all USB suspend control requests
will now be processed using ohci_hub_control()
(like before patch 2e2aa1bcm.)

Tested on an Atmel AT91SAM9G20 with an on-board TI TUSB2046B hub chip
If the last USB device is unplugged from the USB hub, the hub goes into
sleep and will not wakeup when an USB devices is inserted.

Fixes: 2e2aa1bc ("usb: ohci-at91: Forcibly suspend ports while USB suspend")
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.11-rc2

dwc3 got a few fixes this time around:

Fixed an old bug where a broken endpoint descriptor passed in via
userspace through f_fs could prevent dwc3 from working because when
calculating max bursts, we could overwrite top 16 bits of a register.

Also fixed a bug on dwc3's ep_dequeue implementation which wasn't
properly incrementing our TRB dequeue pointer.

dwc3 on omap got two fixes: one for system suspend/resume and another
added a missing break statement on dwc3_omap_set_mailbox().

Apart from these, we have a set of smaller fixes including memory leak
in configfs, build warning fix in atmel udc and a revert of a broken
patch that went in during the merge window

Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that could be triggered by a malicious device.

This avoids leaking up to 56 bytes from after the URB transfer buffer to
user space.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that can be triggered by a malicious device.

This avoids leaking 128 kB of memory content from after the URB transfer
buffer to user space.

Fixes: 8c209e67 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>

Remove the now redundant open callback and let core call the generic
handler for us instead.
Signed-off-by: Johan Hovold <johan@kernel.org>

This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.

Fixes: 4a90f09b ("tty: usb-serial krefs")
Cc: stable <stable@vger.kernel.org>	# 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>

Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Sometimes, we might get a completion for a TRB which is left with HWO
bit. Even in these cases, we should increment req->remaining to
properly report total transferred size. I noticed this while debuggin
a separate problem seen with MSC tests from USBCV. Sometimes we would
erroneously report a completion for a 512-byte transfer when, in
reality, we transferred 0 bytes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In the function scan_dma_completions() there is a reusage of tmp
variable. That coused a wrong value being used in some case when
reading a short packet terminated transaction from an endpoint,
in 2 concecutive reads.

This was my logic for the patch:

The req->td->dmadesc equals to 0 iff:
-- There was a transaction ending with a short packet, and
-- The read() to read it was shorter than the transaction length, and
-- The read() to complete it is longer than the residue.
I believe this is true from the printouts of various cases,
but I can't be positive it is correct.

Entering this if, there should be no more data in the endpoint
(a short packet terminated the transaction).
If there is, the transaction wasn't really done and we should exit and
wait for it to finish entirely. That is the inner if.
That inner if should never happen, but it is there to be on the safe
side. That is why it is marked with the comment /* paranoia */.
The size of the data available in the endpoint is ep->dma->dmacount
and it is read to tmp.
This entire clause is based on my own educated guesses.

If we passed that inner if without breaking in the original code,
than tmp & DMA_BYTE_MASK_COUNT== 0.
That means we will always pass dma bytes count of 0 to dma_done(),
meaning all the requested bytes were read.

dma_done() reports back to the upper layer that the request (read())
was done and how many bytes were read.
In the original code that would always be the request size,
regardless of the actual size of the data.
That did not make sense to me at all.

However, the original value of tmp is req->td->dmacount,
which is the dmacount value when the request's dma transaction was
finished. And that is a much more reasonable value to report back to
the caller.

To recreate the problem:
Read from a bulk out endpoint in a loop, 1024 * n bytes in each
iteration.
Connect the PLX to a host you can control.
Send to that endpoint 1024 * n + x bytes,
such that 0 < x < 1024 * n and (x % 1024) != 0
You would expect the first read() to return 1024 * n
and the second read() to return x.
But you will get the first read to return 1024 * n
and the second one to return 1024 * n.
That is true for every positive integer n.

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Raz Manor <Raz.Manor@valens.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

A call usb_put_phy(udc->transceiver) must be tested for a valid pointer.
Use an already existing test for usb_unregister_notifier call.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We need to break from all cases if we want to treat
each one of them separately.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: d2728fb3 ("usb: dwc3: omap: Pass VBUS and ID events transparently")
Cc: <stable@vger.kernel.org> #v4.8+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On TI platforms (dra7, am437x), the DWC3_DSTS_DEVCTRLHLT bit is not set
after the device controller is stopped via DWC3_DCTL_RUN_STOP.

If we don't disconnect and stop the gadget, it stops working after a
system resume with the trace below.

There is no point in preventing gadget disconnect and gadget stop during
system suspend/resume as we're going to suspend in any case, whether
DEVCTRLHLT timed out or not.

[  141.727480] ------------[ cut here ]------------
[  141.732349] WARNING: CPU: 1 PID: 2135 at drivers/usb/dwc3/gadget.c:2384 dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3]
[  141.744299] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 evdev udc_core m25p80 usb_common spi_nor snd_soc_davinci_mcasp snd_soc_simple_card snd_soc_edma snd_soc_tlv3e
[  141.792163] CPU: 1 PID: 2135 Comm: irq/456-dwc3 Not tainted 4.10.0-rc8 #1138
[  141.799547] Hardware name: Generic DRA74X (Flattened Device Tree)
[  141.805940] [<c01101b4>] (unwind_backtrace) from [<c010c31c>] (show_stack+0x10/0x14)
[  141.814066] [<c010c31c>] (show_stack) from [<c04a0918>] (dump_stack+0xac/0xe0)
[  141.821648] [<c04a0918>] (dump_stack) from [<c013708c>] (__warn+0xd8/0x104)
[  141.828955] [<c013708c>] (__warn) from [<c0137164>] (warn_slowpath_null+0x20/0x28)
[  141.836902] [<c0137164>] (warn_slowpath_null) from [<bf27784c>] (dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3])
[  141.848329] [<bf27784c>] (dwc3_stop_active_transfer.constprop.4 [dwc3]) from [<bf27ab14>] (__dwc3_gadget_ep_disable+0x64/0x528 [dwc3])
[  141.861034] [<bf27ab14>] (__dwc3_gadget_ep_disable [dwc3]) from [<bf27c27c>] (dwc3_gadget_ep_disable+0x3c/0xc8 [dwc3])
[  141.872280] [<bf27c27c>] (dwc3_gadget_ep_disable [dwc3]) from [<bf23b428>] (usb_ep_disable+0x11c/0x18c [udc_core])
[  141.883160] [<bf23b428>] (usb_ep_disable [udc_core]) from [<bf342774>] (disable_ep+0x18/0x54 [usb_f_ss_lb])
[  141.893408] [<bf342774>] (disable_ep [usb_f_ss_lb]) from [<bf3437b0>] (disable_endpoints+0x18/0x50 [usb_f_ss_lb])
[  141.904168] [<bf3437b0>] (disable_endpoints [usb_f_ss_lb]) from [<bf343814>] (disable_source_sink+0x2c/0x34 [usb_f_ss_lb])
[  141.915771] [<bf343814>] (disable_source_sink [usb_f_ss_lb]) from [<bf329a9c>] (reset_config+0x48/0x7c [libcomposite])
[  141.927012] [<bf329a9c>] (reset_config [libcomposite]) from [<bf329afc>] (composite_disconnect+0x2c/0x54 [libcomposite])
[  141.938444] [<bf329afc>] (composite_disconnect [libcomposite]) from [<bf23d7dc>] (usb_gadget_udc_reset+0x10/0x34 [udc_core])
[  141.950237] [<bf23d7dc>] (usb_gadget_udc_reset [udc_core]) from [<bf276d70>] (dwc3_gadget_reset_interrupt+0x64/0x698 [dwc3])
[  141.962022] [<bf276d70>] (dwc3_gadget_reset_interrupt [dwc3]) from [<bf27952c>] (dwc3_thread_interrupt+0x618/0x1a3c [dwc3])
[  141.973723] [<bf27952c>] (dwc3_thread_interrupt [dwc3]) from [<c01a7ce8>] (irq_thread_fn+0x1c/0x54)
[  141.983215] [<c01a7ce8>] (irq_thread_fn) from [<c01a7fbc>] (irq_thread+0x120/0x1f0)
[  141.991247] [<c01a7fbc>] (irq_thread) from [<c015ba14>] (kthread+0xf8/0x138)
[  141.998641] [<c015ba14>] (kthread) from [<c01078f0>] (ret_from_fork+0x14/0x24)
[  142.006213] ---[ end trace b4ecfe9f175b9a9c ]---
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit ac670a3a650b899fc020b81f63e810d06015b865.

This introduce bug we already fixed in
commit 53642399 ("usb: gadget: f_fs: Fix wrong check on reserved1 wof OS_DESC_EXT_COMPAT")

Next FFS (adb) SS enumeration fail with Windows OS.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

'kbuf' is allocated just a few lines above using 'memdup_user()'.
If the 'if (dev->buf)' test fails, this memory is never released.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The debug output now contains the wrong variable, as seen from the compiler
warning:

drivers/usb/gadget/udc/atmel_usba_udc.c: In function 'usba_ep_enable':
drivers/usb/gadget/udc/atmel_usba_udc.c:632:550: error: 'ept_cfg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  DBG(DBG_ERR, "%s: EPT_CFG = 0x%lx (maxpacket = %lu)\n",

This changes the debug output the same way as the other code.

Fixes: 741d2558 ("usb: gadget: udc: atmel: Update endpoint allocation scheme")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The utmi mode is unsigned according the dt-bindings.
Fix sparse issue (-Wtypesign):

  drivers/usb/dwc3/dwc3-omap.c:391:50: warning: incorrect type in argument 3 (different signedness)
  drivers/usb/dwc3/dwc3-omap.c:391:50:    expected unsigned int [usertype] *out_value
  drivers/usb/dwc3/dwc3-omap.c:391:50:    got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When binding a gadget to a device, "name" is stored in gi->udc_name, but
this does not happen when unregistering and the string is leaked.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When the user does device unbind and rebind test, the kernel will
show below dump due to usb_gadget memory region is dirty after unbind.
Clear usb_gadget region for every new probe.

root@imx6qdlsolo:/sys/bus/platform/drivers/dummy_udc# echo dummy_udc.0 > bind
[  102.523312] kobject (eddd78b0): tried to init an initialized object, something is seriously wrong.
[  102.532447] CPU: 0 PID: 734 Comm: sh Not tainted 4.10.0-rc7-00872-g1b2b8e9 #1298
[  102.539866] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[  102.545717] Backtrace:
[  102.548225] [<c010d090>] (dump_backtrace) from [<c010d338>] (show_stack+0x18/0x1c)
[  102.555822]  r7:ede34000 r6:60010013 r5:00000000 r4:c0f29418
[  102.561512] [<c010d320>] (show_stack) from [<c040c2a4>] (dump_stack+0xb4/0xe8)
[  102.568764] [<c040c1f0>] (dump_stack) from [<c040e6d4>] (kobject_init+0x80/0x9c)
[  102.576187]  r10:0000001f r9:eddd7000 r8:eeaf8c10 r7:eddd78a8 r6:c177891c r5:c0f3b060
[  102.584036]  r4:eddd78b0 r3:00000000
[  102.587641] [<c040e654>] (kobject_init) from [<c05359a4>] (device_initialize+0x28/0xf8)
[  102.595665]  r5:eebc4800 r4:eddd78a8
[  102.599268] [<c053597c>] (device_initialize) from [<c05382ac>] (device_register+0x14/0x20)
[  102.607556]  r7:eddd78a8 r6:00000000 r5:eebc4800 r4:eddd78a8
[  102.613256] [<c0538298>] (device_register) from [<c0668ef4>] (usb_add_gadget_udc_release+0x8c/0x1ec)
[  102.622410]  r5:eebc4800 r4:eddd7860
[  102.626015] [<c0668e68>] (usb_add_gadget_udc_release) from [<c0669068>] (usb_add_gadget_udc+0x14/0x18)
[  102.635351]  r10:0000001f r9:eddd7000 r8:eddd788c r7:bf003770 r6:eddd77f8 r5:eddd7818
[  102.643198]  r4:eddd785c r3:eddd7b24
[  102.646834] [<c0669054>] (usb_add_gadget_udc) from [<bf003428>] (dummy_udc_probe+0x170/0x1c4 [dummy_hcd])
[  102.656458] [<bf0032b8>] (dummy_udc_probe [dummy_hcd]) from [<c053d114>] (platform_drv_probe+0x54/0xb8)
[  102.665881]  r10:00000008 r9:c1778960 r8:bf004128 r7:fffffdfb r6:bf004128 r5:eeaf8c10
[  102.673727]  r4:eeaf8c10
[  102.676293] [<c053d0c0>] (platform_drv_probe) from [<c053b160>] (driver_probe_device+0x264/0x474)
[  102.685186]  r7:00000000 r6:00000000 r5:c1778960 r4:eeaf8c10
[  102.690876] [<c053aefc>] (driver_probe_device) from [<c05397c4>] (bind_store+0xb8/0x14c)
[  102.698994]  r10:eeb3bb4c r9:ede34000 r8:0000000c r7:eeaf8c44 r6:bf004128 r5:c0f3b668
[  102.706840]  r4:eeaf8c10
[  102.709402] [<c053970c>] (bind_store) from [<c0538ca8>] (drv_attr_store+0x28/0x34)
[  102.716998]  r9:ede34000 r8:00000000 r7:ee3863c0 r6:ee3863c0 r5:c0538c80 r4:c053970c
[  102.724776] [<c0538c80>] (drv_attr_store) from [<c029c930>] (sysfs_kf_write+0x50/0x54)
[  102.732711]  r5:c0538c80 r4:0000000c
[  102.736313] [<c029c8e0>] (sysfs_kf_write) from [<c029be84>] (kernfs_fop_write+0x100/0x214)
[  102.744599]  r7:ee3863c0 r6:eeb3bb40 r5:00000000 r4:00000000
[  102.750287] [<c029bd84>] (kernfs_fop_write) from [<c0222dd8>] (__vfs_write+0x34/0x120)
[  102.758231]  r10:00000000 r9:ede34000 r8:c0108bc4 r7:0000000c r6:ede35f80 r5:c029bd84
[  102.766077]  r4:ee223780
[  102.768638] [<c0222da4>] (__vfs_write) from [<c0224678>] (vfs_write+0xa8/0x170)
[  102.775974]  r9:ede34000 r8:c0108bc4 r7:ede35f80 r6:01861cb0 r5:ee223780 r4:0000000c
[  102.783743] [<c02245d0>] (vfs_write) from [<c0225498>] (SyS_write+0x4c/0xa8)
[  102.790818]  r9:ede34000 r8:c0108bc4 r7:0000000c r6:01861cb0 r5:ee223780 r4:ee223780
[  102.798595] [<c022544c>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
[  102.806188]  r7:00000004 r6:b6e83d58 r5:01861cb0 r4:0000000c

Fixes: 90fccb52 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit 4fbac520.

This commit breaks g_webcam when used with uvc-gadget [1].

The user space application (e.g. uvc-gadget) is responsible for
sending response to UVC class specific requests on control endpoint
in uvc_send_response() in uvc_v4l2.c.

The bad commit was causing a duplicate response to be sent with
incorrect response data thus causing UVC probe to fail at the host
and broken control transfer endpoint at the gadget.

[1] - git://git.ideasonboard.org/uvc-gadget.git

Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.

Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d380889 ("USB: serial: digi_acceleport: fix OOB data sanity
check")
Cc: stable <stable@vger.kernel.org>	# v2.6.30: 2d380889Signed-off-by: Johan Hovold <johan@kernel.org>

If request was already started, this means we had to
stop the transfer. With that we also need to ignore
all TRBs used by the request, however TRBs can only
be modified after completion of END_TRANSFER
command. So what we have to do here is wait for
END_TRANSFER completion and only after that jump
over TRBs by clearing HWO and incrementing dequeue
pointer.

Note that we have 2 possible types of transfers
here:

i) Linear buffer request
ii) SG-list based request

SG-list based requests will have r->num_pending_sgs
set to a valid number (> 0). Linear requests,
normally use a single TRB.

For each of these two cases, if r->unaligned flag is
set, one extra TRB has been used to align transfer
size to wMaxPacketSize.

All of these cases need to be taken into
consideration so we don't mess up our TRB ring
pointers.
Tested-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.

Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.

In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.

Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull networking fixes from David Miller:

 1) Fix double-free in batman-adv, from Sven Eckelmann.

 2) Fix packet stats for fast-RX path, from Joannes Berg.

 3) Netfilter's ip_route_me_harder() doesn't handle request sockets
    properly, fix from Florian Westphal.

 4) Fix sendmsg deadlock in rxrpc, from David Howells.

 5) Add missing RCU locking to transport hashtable scan, from Xin Long.

 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.

 7) Fix race in NAPI handling between poll handlers and busy polling,
    from Eric Dumazet.

 8) TX path in vxlan and geneve need proper RCU locking, from Jakub
    Kicinski.

 9) SYN processing in DCCP and TCP need to disable BH, from Eric
    Dumazet.

10) Properly handle net_enable_timestamp() being invoked from IRQ
    context, also from Eric Dumazet.

11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.

12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
    Melo.

13) Fix use-after-free in netvsc driver, from Dexuan Cui.

14) Fix max MTU setting in bonding driver, from WANG Cong.

15) xen-netback hash table can be allocated from softirq context, so use
    GFP_ATOMIC. From Anoob Soman.

16) Fix MAC address change bug in bgmac driver, from Hari Vyas.

17) strparser needs to destroy strp_wq on module exit, from WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  strparser: destroy workqueue on module exit
  sfc: fix IPID endianness in TSOv2
  sfc: avoid max() in array size
  rds: remove unnecessary returned value check
  rxrpc: Fix potential NULL-pointer exception
  nfp: correct DMA direction in XDP DMA sync
  nfp: don't tell FW about the reserved buffer space
  net: ethernet: bgmac: mac address change bug
  net: ethernet: bgmac: init sequence bug
  xen-netback: don't vfree() queues under spinlock
  xen-netback: keep a local pointer for vif in backend_disconnect()
  netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
  netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
  netfilter: nf_conntrack_sip: fix wrong memory initialisation
  can: flexcan: fix typo in comment
  can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
  can: gs_usb: fix coding style
  can: gs_usb: Don't use stack memory for USB transfers
  ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
  ixgbe: update the rss key on h/w, when ethtool ask for it
  ...

Pull more KVM updates from Radim Krčmář:
 "Second batch of KVM changes for the 4.11 merge window:

  PPC:
   - correct assumption about ASDR on POWER9
   - fix MMIO emulation on POWER9

  x86:
   - add a simple test for ioperm
   - cleanup TSS (going through KVM tree as the whole undertaking was
     caused by VMX's use of TSS)
   - fix nVMX interrupt delivery
   - fix some performance counters in the guest

  ... and two cleanup patches"

* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Fix pending events injection
  x86/kvm/vmx: remove unused variable in segment_base()
  selftests/x86: Add a basic selftest for ioperm
  x86/asm: Tidy up TSS limit code
  kvm: convert kvm.users_count from atomic_t to refcount_t
  KVM: x86: never specify a sample period for virtualized in_tx_cp counters
  KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
  KVM: PPC: Book3S HV: Fix software walk of guest process page tables