Add the PCI device ids required for driver registration. Remove
pvt->ctl_name and use the family descriptor directly, instead. Then,
bump driver version and fixup its format. Finally, enable DRAM ECC
decoding on F15h.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

F15h has the same ECC symbol size options as F10h revD and later so
adjust checks to that. Simplify code a bit.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Drop per-instance variable and compute min scrubrate dynamically.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

With increasing number of PCI function ids, add the PCI function id
in the define name instead of its symbolic name in the BKDG for more
clarity.
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Drop static tables which map the bits in F2x80 to a chip select size in
favor of functions doing the mapping with some bit fiddling. Also, add
F15 support.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

This function is relevant for F10h and higher, and it has only one
callsite so drop its function pointer from the low_ops struct.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

F15h sys_addr to chip select mapping is almost identical to F10h's so
reuse that. Rename functions on that path accordingly.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Add paranoid checks for the sys address before going off and decoding
it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Replace per-DCT macros with smarter ones, drop hack and look for the
spare rank on all chip selects on a channel.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Remove the channel interleave select bit properly. See
F2x110[DctSelIntLvAddr] for details.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

When node interleaving is enabled, a subset of the addr[14:12] bits has
to be removed in order to get the normalized DCT address of the DRAM
channel. The actual number of bits to remove is determined by F1x[1,
0][7C:40][IntlvEn]. Do this correctly.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

On revC3 and revE Fam10h machines and later, non-interleaved graphics
framebuffer memory under the 16G mark can be swapped with a region
located at the bottom of memory so that the GPU can use the interleaved
region and thus two channels. Add support for that.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

The address bits from MC4_STATUS differ only between K8 and the rest so
no need for a per-family method.

No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Use the struct mce directly instead of copying from it into a custom
struct err_regs.

No functionality change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

The only difference is that F10h used to sport ganged DCTs and F15h
doesn't so adjust the F10h routine and reuse it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Remove unused defines, drop family names from define names.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Remove reporting of errors with UC bit set - this is done by the MCE
decoding code anyway and this driver deals with DRAM ECC errors only. UC
(NB uncorrectable error) doesn't necessarily mean it is a DRAM error.
Remove unused macros while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

The fact whether we are chipkill capable or not does not have any
bearing when computing the channel index on a ganged DCT configuration
so remove that. Also, simplify debug statements. Finally, remove old
error injection leftovers, while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Remove family names from macro names, drop single bit defines and
comment their meaning instead.

No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Shorten macro names, remove family name from macros, fix macro
arguments, shorten debug strings.

No functionality change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

* Restrict DCT ganged mode check since only Fam10h supports it
* Adjust DRAM type detection for BD since it only supports DDR3
* Remove second and thus unneeded DCLR read in k8_early_channel_count() - we do
  that in read_mc_regs()
* Cleanup comments and remove family names from register macros
* Remove unused defines

There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Do not read DBAM regs twice and simplify code around them.

There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Replace hard to read hex constants with a continuous masks macro.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

This function maps the system address to the normalized DCT address.
Document what the code does for more clarity and wrap insane bitmasks in
a more understandable macro which generates them. Also, reduce number of
arguments passed to the function. Finally, rename this function to what
it actually does.

No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Cleanup and simplify f10_determine_channel(); make it more readable.
Also drop f10_map_intlv_en_to_shift() in favor of simply counting the
bits in F1x124[DramIntlvEn] which is equivalent.

There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Add a struct representing the DRAM chip select base/limit register
pairs. Concentrate all CS handling in a single function. Also, add CS
looping macros for cleaner, more readable code. While at it, adjust code
to F15h. Finally, do smaller macro names cleanups (remove family names
from register macros) and debug messages clarification.

No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Adjust to F15h, simplify code, fixup macros.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Add a struct representing the DRAM base/limit range pairs and remove all
cached subfields. Replace them with accessor functions, which actually
saves us some space:

   text    data     bss     dec     hex filename
  14712    1577     336   16625    40f1 drivers/edac/amd64_edac_mod.o.after
  14831    1609     336   16776    4188 drivers/edac/amd64_edac_mod.o.before

Also, it simplifies the code a lot allowing to merge the K8 and F10h
routines.

No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

F15h "multiplexes" between the configuration space of the two DRAM
controllers by toggling D18F1x10C[DctCfgSel] while F10h has a different
set of registers for DCT0, and DCT1 in extended PCI config space.

Add DCT configuration space accessors per family thus wrapping all the
different access prerequisites. Clean up code while at it, shorten
names.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Raise the debug level of these routines so that their output get issued
out only when the highest debug level is selected. Otherwise, don't
pollute driver debug output.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
  MN10300: atomic_read() should ensure it emits a load
  MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
  MN10300: Proper use of macros get_user() in the case of incremented pointers

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
  MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
  MIPS: MTX-1: Make au1000_eth probe all PHY addresses
  MIPS: Jz4740: Add HAVE_CLK
  MIPS: Move idle task creation to work queue
  MIPS, Perf-events: Use unsigned delta for right shift in event update
  MIPS, Perf-events: Work with the new callchain interface
  MIPS, Perf-events: Fix event check in validate_event()
  MIPS, Perf-events: Work with the new PMU interface
  MIPS, Perf-events: Work with irq_work
  MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
  MIPS: Loongson: Fix potentially wrong string handling
  MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
  MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
  MIPS: Remove unused code from arch/mips/kernel/syscall.c
  MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
  MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
  MIPS: Select R4K timer lib for all MSP platforms
  MIPS: Loongson: Remove ad-hoc cmdline default
  MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
  MIPS: Add an unreachable return statement to satisfy buggy GCCs.
  ...

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: ce4100: Set pci ops via callback instead of module init
  x86/mm: Fix pgd_lock deadlock
  x86/mm: Handle mm_fault_error() in kernel space
  x86: Don't check for BIOS corruption in first 64K when there's no need to

This reverts the parent commit.  I hate doing that, but it's generating
some discussion ("half of it is right"), and since I am planning on
doing the 2.6.38 release later today we can punt it to stable if
required. Let's not rock the boat right now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

oom_kill_process() starts with victim_points == 0.  This means that
(most likely) any child has more points and can be killed erroneously.

Also, "children has a different mm" doesn't match the reality, we should
check child->mm != t->mm.  This check is not exactly correct if t->mm ==
NULL but this doesn't really matter, oom_kill_task() will kill them
anyway.

Note: "Kill all processes sharing p->mm" in oom_kill_task() is wrong
too.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.

Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.

CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Jz4740 supports the clock framework but doesn't have HAVE_CLK defined,
so define it!
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2112/Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.

If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer.  This causes BUG() in per_cpu_trap_init.

This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>