- 03 Feb, 2015 17 commits
-
-
Sujith Manoharan authored
Printing the value of the wakeup status is sufficient. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
The various variables tracking bmiss interrupts are not really used anywhere except in a debug message. Remove them since they have no functional purpose. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
This patch makes sure that valid WOW triggers are present before trying to suspend the device. Also, introduce and use ATH_OP_WOW_ENABLED to bypass PCI suspend and clear it in resume(). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
Registering the card as a wakeup source needs to be done once, during initialization. When the WOW configuration changes, the card's status as wakeup source needs to be changed too and this is done via the set_wakeup() callback. Also, make sure the device is removed properly using ath9k_deinit_wow(). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
If CONFIG_ATH9K_CHANNEL_CONTEXT is enabled, check whether multiple contexts are active and if so, return 1 without enabling WOW since we don't support it in this case. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
If multiple interfaces are active or there is no associated station interface, bail out early and return 1 so that mac80211 can proceed with the normal suspend routine. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
WOW capability is registered with mac80211 only when the device has the ability to wakeup, so there is no need to check in the suspend() routine. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
Do not try to cancel work instances and ANI when the device is not present or WOW triggers are not configured. Bail out early and use ath_err() for such error conditions. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
Enabling WOW based on the chip is incorrect since it needs to be done for specific sub-devices which have proper platform support. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Amitkumar Karwar authored
When AP is started, firmware exits power save mode. This means power save manager of AP takes priority over station. Firmware stop sending periodic AWAKE events to host. We may have UAPSD enabled on station which buffers data packets until AWAKE event from firmware. Data path is unnecessarily blocked in this case. This patch disables UAPSD mode to reenable transmit data path. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Amitkumar Karwar authored
This patch makes sure that skb is freed after downloading NULL packet in error cases. Also, USB chipsets return -EINPROGRESS after downloading packets, they are freed in USB completion handler later. We will add missing change to set tx_lock_flag for USB which blocks further packets. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Amitkumar Karwar authored
Memory is leaked after downloading already processed packet. This patch fixes the problem by freeing returned skb. Other transmit paths don't have this problem. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Amitkumar Karwar authored
Wakeup timer is in sync with 'pm_wakeup_fw_try' flag. It has been started instead of cancelling at one place. This patch corrects it. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Troy Tan authored
There are instances where the DMA engine stalls. The new code detects such stalls and restarts DMA without needing a power reset. Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.18] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Troy Tan authored
The firmware supplies two kinds of packets via the RX mechanism. Besides the normal data received over the air, these packets may contain bluetooth status and other information. The present code fails to detect which kind of information was received. Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [V3.18] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Troy Tan authored
Initially, the routine to update the write point in the FIFO buffer was coded to save CPU time by not doing the calculation every interrupt. This was an error and results in TX hangs. Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [V3.18] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Troy Tan authored
When the buffer descriptor index exceeds 2, then a TX HANG condition will result. Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [V3.18] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
- 29 Jan, 2015 23 commits
-
-
Rafał Miłecki authored
There are new (not anymore?) Broadcom 802.11ac wireless cards based on chipsets like BCM4352 and BCM4360. They use a new PHY type (called simply AC) that will require new specific code. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rafał Miłecki authored
AC-PHY hardware includes new control 0x3 bits that need to be set to the 0x1 by default. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rafał Miłecki authored
This is stil incomplete, so we don't add PCI IDs of new devices yet. Purpose of this patch is to allow testing & adjusting rest of the code. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rafał Miłecki authored
There are some PCIe core fixes that need to be applied before accessing SPROM, otherwise reading it may fail. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rafał Miłecki authored
This allows us to drop some #ifdef magic (mess). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rafał Miłecki authored
Extracting values from it is still unsupported, but at least we'll display some meaningful error now. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rafał Miłecki authored
These chipsets don't need changing clock mode. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
On some AR955x/QCA953x boards, noise floor calibration gets stuck and the cause is a hardware/BB issue. To fix this, peak detect calibration in the HW is disabled and is done in the driver instead. There a few differences with the calibration routine for older chips like AR9331. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
The value is different for PCOEM cards and AR955x/AR953x. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
The LNA gain setting override needs to be done only for AR9330 and PCOEM chips. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
This can be used if we need to apply register settings for all PCOEM solutions (in the AR9003 family). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
This patch disables HW peak detect calibration for AR955x, since it is problematic on a few boards. Instead, manual calibration will be done in the driver. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sujith Manoharan authored
This patch disables HW peak detect calibration for QCA953x, since it is problematic on a few boards. Instead, manual calibration will be done in the driver. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Michael Büsch authored
b43 has a FIXME about locking in the mac80211 set-beacon-int callback for a long time. As it turns out there actually is a tiny race window that could result in a use-after-free bug of the 'current_beacon' memory. Nobody ever reported this, so it probably never happened. Fix this by adding a spin lock that protects the current_beacon access. We must not be in atomic context while accessing hardware (due to SDIO), so the beacon update bottom half has to clone the skb and release the lock before writing it to hardware. Let's all hope that this stops the troll who is trying to submit incorrect fixes for this issue repeatedly. And let's hope that I'm not a troll, too, who just hides even more evil code in an even more complex attempt to fix the issue. Signed-off-by: Michael Buesch <m@bues.ch> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
This patch enables 11h extensions in FW upon detecting DFS channel in start radar detection/channel switch handlers. Patch also takes care of disabling 11h when non DFS channels are to be set during start_ap handler. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
This patch adds cfg80211 channel_switch support for mwifiex. Upon receiving channel switch request, driver would parse channel switch announcement IE from beacon_data. If TX is blocked, netdev queues are stopped. IEs from csa_beacon are then parsed and set to FW. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
This patch adds support for radar_detected event from FW. Driver in turn would stop netdev queues to stop TX traffic and issue RADAR_DETECT event to cfg80211. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
This patch adds support for channel report enabling. Channel report event happens if radar is detected on specified channel after driver has issued radar detect command within CAC time. Driver in turn sends RADAR_DETECTED event to cfg80211 to tell radar was detected within CAC time. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
This patch adds support for cfg80211 start_radar_detection handler. Upon reception of start_radar_detection, driver prepares radar detect command to FW. Delayed work is queued for CAC time which sends radar detection finished event to cfg80211. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
Head & Tail IEs are supposed to be added to beacon and probe response. This patch adds separate function for parsing head and tail IEs from cfg80211_beacon_data and sets them to FW. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
Refactor mwifiex_cfg80211_start_ap by creating separate function to set AP channel and another for configuring other AP parameters and starting AP. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Avinash Patil authored
This patch moves IE management routine to end of start_ap handler. IEs now would be updated after AP has started. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Qingshui Gao <gaoqs@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-