The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A80 SoC has an NMI controller. NMI is an external
interrupt pin exclusely used with PMICs and other system critical
peripherals (such as RTC) in Allwinner's reference designs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A80 dtsi.

Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A80 Optimus board has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A80 SoC has a consumer IR receiver, which is the same as
older SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

LED3 is connected to pin PM15 on R_PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A80 has a secondary pin controller. Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The main (24MHz) clock on the A80 is configurable via the PRCM address
space. The low power/speed (32kHz) clock is from an external chip, the
AC100.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds the supported PRCM clocks and reset controls to the A80 dtsi.
The DAUDIO module clocks are not supported yet.

Also update clock and reset phandles for r_uart.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the touchscreen found on the pov protab2-ips9
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the touchscreen controller used on the iNet1 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the AXP152 pmic used on Auxtek T004 boards.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the pov protab2 ips9
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the UTOO P66 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the iNet1 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The iNet1 tablet uses the A10's integrated audio codec, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.

Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Gemei G9 has internal speakers and headphone jack. Audio switching
from internal speakers to headphones is automatically handled by
extra FT2012Q audio amplifier chip that works out of the box.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

ADC seems to be using ldo2 for reference voltage.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add regulator nodes for axp209 using the axp209.dtsi include.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The inet9f-rev03 tablet has multiple fire-buttons / direction controls,
add support for these using the same axis mapping as ps2 compatible game
controllers with the same stick / button layout use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable on-chip audio codec on the Wexler TAB7200 tablet.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec on the Olimex A20-SOM-EVB
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the axp221 PMIC chip in the dts file.

Allows board to power off correctly from the poweroff command

This board requires dc1sw to be enabled in order to provide a power source
for the 5V DCDC converter that powers USB2.

This board uses dldo1 for 3.3V wifi power

This board requires dldo3 to be enabled at 2.8V in order to provide voltage
to the pullup resistors for the i2c0 bus.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This baseboard from SWAC is equipped with the ICnova-A20 SoM from
Incircuit. This board is equipped with the following interfaces /
devices:

- 512 MiB SDRAM
- 4 GiB MLC NAND (Micron MT29F32G08CBACAWP or Hynix H27UBG8T2BTR)
- USB host
- LCD 800x480
- HDMI
- CAN

Note that the NAND support is still missing. As its currently not
supported in mainline for sunxi and especially for these MLC
devices.

The original plan was to also provide a dtsi for the ICnova SoM,
to put all the SoM internal nodes / properties there. But as I
don't have a clear overview of the SoM specific and baseboard
specific differences, I'm putting all in one dts for now. Once
somebody pushed support for some other baseboard using the
A20 SoM from Incircuit (e.g. the ADB4006 reference design), this
should be separated.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marcus Heuer <marcus.heuer@swac.de>
[maxime: Fixed CPU regulator upper voltage boundary]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The pcDuino V3 Nano has a 3.5mm TRRS jack socket for audio, using the
CTIA standard pinout, connected to HPOUTL, HPOUTR, HPCOM/HPCOMFB and
MICIN1/VMIC (via appropriate RC networks) on the A20. The PH00 GPIO is
wired for headphone plug detection: it reads 0 when nothing's plugged
in, and 1 when a plug is inserted.

LINEINL/R and FMINL/R are not connected.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pull perf updates from Thomas Gleixner:
 "Mostly updates to the perf tool plus two fixes to the kernel core code:

   - Handle tracepoint filters correctly for inherited events (Peter
     Zijlstra)

   - Prevent a deadlock in perf_lock_task_context (Paul McKenney)

   - Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
     Melo)

   - Print full source file paths when using 'perf annotate --print-line
     --full-paths' (Michael Petlan)

   - Fix 'perf probe -d' when just one out of uprobes and kprobes is
     enabled (Wang Nan)

   - Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
     tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)

   - Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
     the 'perf test' LLVM entries, when running it in-tree, to
     .gitignore (Yunlong Song)

   - libbpf error reporting improvements, using a strerror interface to
     more precisely tell the user about problems with the provided
     scriptlet, be it in C or as a ready made object file (Wang Nan)

   - Do not be case sensitive when searching for matching 'perf test'
     entries (Arnaldo Carvalho de Melo)

   - Inform the user about objdump failures in 'perf annotate' (Andi
     Kleen)

   - Improve the LLVM 'perf test' entry, introduce a new ones for BPF
     and kbuild tests to check the environment used by clang to compile
     .c scriptlets (Wang Nan)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
  tools include: Add compiler.h to list.h
  perf probe: Verify parameters in two functions
  perf session: Add missing newlines to some pr_err() calls
  perf annotate: Support full source file paths for srcline fix
  perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
  perf: Fix inherited events vs. tracepoint filters
  perf: Disable IRQs across RCU RS CS that acquires scheduler lock
  perf test: Do not be case sensitive when searching for matching tests
  perf test: Add 'perf test BPF'
  perf test: Enhance the LLVM tests: add kbuild test
  perf test: Enhance the LLVM test: update basic BPF test program
  perf bpf: Improve BPF related error messages
  perf tools: Make fetch_kernel_version() publicly available
  bpf tools: Add new API bpf_object__get_kversion()
  bpf tools: Improve libbpf error reporting
  perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
  perf annotate: Inform the user about objdump failures in --stdio
  perf stat: Make stat options global
  perf sched latency: Fix thread pid reuse issue
  ...

Pull scheduler fix from Thomas Gleixner:
 "A single fix to prevent math underflow in the numa balancing code"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/numa: Fix math underflow in task_tick_numa()

Pull liblockdep fixes from Thomas Gleixner:
 "Three small patches to synchronize liblockdep with the latest core
  changes"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/liblockdep: explicitly declare lockdep API we call from liblockdep
  tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER
  tools/liblockdep: remove task argument from debug_check_no_locks_held

Pull x86 fixes from Thomas Gleixner:
 "A couple of fixes and updates related to x86:

   - Fix the W+X check regression on XEN

   - The real fix for the low identity map trainwreck

   - Probe legacy PIC early instead of unconditionally allocating legacy
     irqs

   - Add cpu verification to long mode entry

   - Adjust the cache topology to AMD Fam17H systems

   - Let Merrifield use the TSC across S3"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Call verify_cpu() after having entered long mode too
  x86/setup: Fix low identity map for >= 2GB kernel range
  x86/mm: Skip the hypervisor range when walking PGD
  x86/AMD: Fix last level cache topology for AMD Fam17h systems
  x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
  x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield