i.MX93 use TMU version 2.1, which supports:
 - TRITSR_TP5(When this field is 1, you must add 0.5 K to the temperature
   that TEMP reports. For example, if TEMP is 300 K and TP5=1, then the
   final temperature is 300.5 K.)
 - Has 16 TTRCR register: Temperature Range Control (TTRCR0 - TTRCR15)

This patch is to add this support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-4-peng.fan@oss.nxp.com

There are MAX 16 sensors, but not all of them supported. Such as
i.MX8MQ, there are only 3 sensors. Enabling all 16 sensors will
touch reserved bits from i.MX8MQ reference mannual, and TMU will stuck,
temperature will not update anymore.

Fixes: 45038e03 ("thermal: qoriq: Enable all sensors before registering them")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-3-peng.fan@oss.nxp.com

No need to program site adjustment register, as programming
these registers do not give accurate value and also these
registers are not mentioned in Reference Manual.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-2-peng.fan@oss.nxp.com

Register thermal zones as hwmon sensors to let userspace read
temperatures using standard hwmon interface.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230613091317.1691247-1-wenst@chromium.org

Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.

Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.

Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:

	3.3.6.4. Gating and reset

	Make sure that the reset signal has been released before the release of
	module clock gating;

This fixes the issue and removes some LoC at the same time.

Fixes: dccc5c3b ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr

This reverts commit f05c7b7d.

That change was causing a regression in the generic-adc-thermal-probed
bootrr test as reported in the kernelci-results list [1].
A proper rework will take longer, so revert it for now.

[1] https://groups.io/g/kernelci-results/message/42660

Fixes: f05c7b7d ("thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe")
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230525121811.3360268-1-ricardo.canuelo@collabora.com

The MSM8909 SoC has 5 thermal sensors in a TSENS v0.1 block. Like
MDM9607 it uses a non-standard default slope value of 3000 [1] and needs
per-sensor "correction factors" to workaround issues with the factory
calibration [2].

[1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LA.UM.7.7.c26-09100-8x09.0/arch/arm/boot/dts/qcom/msm8909.dtsi#L476
[2]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/6df022c6d0c2c1b4a5a6c2124dba4d57910c0911Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-6-5eb632235ba7@kernkonzept.com

MSM8909 uses the TSENS v0.1 block similar to other SoCs like MDM9607.
Document the "qcom,msm8909-tsens" compatible in the existing schema.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-5-5eb632235ba7@kernkonzept.com

Since the SoC compatibles must be followed by the IP version compatible
(e.g. compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";) it is
redundant to list all the SoC compatibles again in the if statement.
It will already match the IP-version compatible.

The list has already become inconsistent since for example
"qcom,msm8939-tsens" is covered by the if statement but is not listed
there explicitly like the other SoCs.

Simplify this by dropping the redundant SoC compatibles. ipq8064 and
msm8960 are still needed because they do not have an IP-version
compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-4-5eb632235ba7@kernkonzept.com

According to the msm-3.18 vendor kernel from Qualcomm, mdm9607 needs
"correction factors" to adjust for additional offsets observed after the
factory calibration values in the fuses [1, 2].

The fixed offsets should be applied unless there is a special
calibration mode value that indicates that no offsets are needed [3].

Note that the new calibration mode values are called differently in this
patch compared to the vendor kernel:
  - TSENS_TWO_POINT_CALIB_N_WA        -> ONE_PT_CALIB2_NO_OFFSET
  - TSENS_TWO_POINT_CALIB_N_OFFSET_WA -> TWO_PT_CALIB_NO_OFFSET
This is because close inspection of the calibration function [3] reveals
that TSENS_TWO_POINT_CALIB_N_WA is actually a "one point" calibration
because the if statements skip all "point2" related code for it.

[1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d9d2db1b82bf3f72f5de0803d55e6849eb5b671e
[2]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d75aef53a760e8ff7bac54049d00c8b2ee1b193e
[3]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/drivers/thermal/msm-tsens.c#L2987-3136

Fixes: a2149ab8 ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-3-5eb632235ba7@kernkonzept.com

According to the msm-3.18 vendor kernel from Qualcomm [1], mdm9607 uses
a non-standard slope value of 3000 (instead of 3200) for all sensors.
Fill it properly similar to the 8939 code added recently.

[1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/arch/arm/boot/dts/qcom/mdm9607.dtsi#L875

Fixes: a2149ab8 ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-2-5eb632235ba7@kernkonzept.com

The old single-cell parsing code was removed for MSM8939, MDM9607 and
MSM8976 but for some reason the structs defining the bit positions etc
were kept around (unused). Drop them now.

Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 51d78b8b ("thermal/drivers/tsens: Drop single-cell code for mdm9607")
Fixes: dfadb459 ("thermal/drivers/tsens: Drop single-cell code for msm8939")
Fixes: 3a908971 ("thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-1-5eb632235ba7@kernkonzept.com

Qualcomm IPQ9574 has tsens v2.3.1 block, which is similar to IPQ8074 tsens.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/ec9799504fe5a141e107bb78955d8d427f00553f.1686125196.git.quic_varada@quicinc.com

Convert the DT binding document for bcm2835-thermal from .txt to YAML.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230604121223.9625-10-stefan.wahren@i2se.com

For many setups the bang-bang governor is exactly what we want. Many
ARM SoC-based devices use fans to cool down the entire SoC and that
works well only with the bang-bang governor because it uses the
hysteresis in order to let the fan run for a while to cool the SoC
down below the trip point before switching it off again.

The step-wise governor will behave strangely in these situations. It
doesn't use the hysteresis, so it can lead to situations where the fan
is turned on for only a very brief period and then is switched back off,
only to get switched back on again very quickly because the SoC hasn't
cooled down very much.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230609124408.3788680-1-thierry.reding@gmail.comSigned-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The MSM8226 TSENS IP has 6 thermal sensors in a TSENS v0.1 block.
The thermal sensors use non-standard slope values.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230507201225.89694-4-matti.lehtimaki@gmail.com

Qualcomm MSM8226 has tsens v0.1 block.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230507201225.89694-3-matti.lehtimaki@gmail.com

The registers are differently named and at different offsets, but their
functionality is the same as for Gen3.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-4-wsa+renesas@sang-engineering.com

Gen4 will be very different, so refactor Gen3 access into separate call
first.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-3-wsa+renesas@sang-engineering.com

More items to describe the TSCs are needed soon, so encapsulate the
current 'ths_tj_1' item into a struct.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-2-wsa+renesas@sang-engineering.com

The Qualcomm SM6375 platform has two instances of the tsens v2.8.0 block,
add a compatible for these instances.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516-topic-lost_tsens_bindings-v1-2-99715746ddb1@linaro.org

Add the TSENS v2.x controller found on QCM2290.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516-topic-lost_tsens_bindings-v1-1-99715746ddb1@linaro.org

Since commit 955fb871 ("thermal/intel/intel_soc_dts_iosf: Use Intel
TCC library") intel_soc_dts_iosf is reporting the wrong temperature.

The driver expects tj_max to be in milli-degrees-celcius but after
the switch to the TCC library this is now in degrees celcius so
instead of e.g. 90000 it is set to 90 causing a temperature 45
degrees below tj_max to be reported as -44910 milli-degrees
instead of as 45000 milli-degrees.

Fix this by adding back the lost factor of 1000.

Fixes: 955fb871 ("thermal/intel/intel_soc_dts_iosf: Use Intel TCC library")
Reported-by: Bernhard Krug <b.krug@elektronenpumpe.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull x86 fix from Borislav Petkov:

 - Set up the kernel CS earlier in the boot process in case EFI boots
   the kernel after bypassing the decompressor and the CS descriptor
   used ends up being the EFI one which is not mapped in the identity
   page table, leading to early SEV/SNP guest communication exceptions
   resulting in the guest crashing

* tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/head/64: Switch to KERNEL_CS as soon as new GDT is installed

Pull smb server fixes from Steve French:
 "Five smb3 server fixes, all also for stable:

   - Fix four slab out of bounds warnings: improve checks for protocol
     id, and for small packet length, and for create context parsing,
     and for negotiate context parsing

   - Fix for incorrect dereferencing POSIX ACLs"

* tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
  ksmbd: validate smb request protocol id
  ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
  ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
  ksmbd: fix out-of-bound read in parse_lease_state()
  ksmbd: fix out-of-bound read in deassemble_neg_contexts()

Pull i2c fixes from Wolfram Sang:
 "Biggest news is that Andi Shyti steps in for maintaining the
  controller drivers. Thank you very much!

  Other than that, one new driver maintainer and the rest is usual
  driver bugfixes. at24 has a Kconfig dependecy fix"

* tag 'i2c-for-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver
  eeprom: at24: also select REGMAP
  i2c: sprd: Delete i2c adapter in .remove's error path
  i2c: mv64xxx: Fix reading invalid status value in atomic mode
  i2c: designware: fix idx_write_cnt in read loop
  i2c: mchp-pci1xxxx: Avoid cast to incompatible function type
  i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate"
  MAINTAINERS: Add myself as I2C host drivers maintainer

Pull soundwire fixes from Vinod Koul:
 "Core fix for missing flag clear, error patch handling in qcom driver
  and BIOS quirk for HP Spectre x360:

   - HP Spectre x360 soundwire DMI quirk

   - Error path handling for qcom driver

   - Core fix for missing clear of alloc_slave_rt"

* tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
  soundwire: stream: Add missing clear of alloc_slave_rt
  soundwire: qcom: add proper error paths in qcom_swrm_startup()
  soundwire: dmi-quirks: add new mapping for HP Spectre x360

Pull ARM SoC fixes from Arnd Bergmann:
 "Most of the changes this time are for the Qualcomm Snapdragon
  platforms.

  There are bug fixes for error handling in Qualcomm icc-bwmon,
  rpmh-rsc, ramp_controller and rmtfs driver as well as the AMD tee
  firmware driver and a missing initialization in the Arm ff-a firmware
  driver. The Qualcomm RPMh and EDAC drivers need some rework to work
  correctly on all supported chips.

  The DT fixes include:

   - i.MX8 fixes for gpio, pinmux and clock settings

   - ADS touchscreen gpio polarity settings in several machines

   - Address dtb warnings for caches, panel and input-enable properties
     on Qualcomm platforms

   - Incorrect data on qualcomm platforms fir SA8155P power domains,
     SM8550 LLCC, SC7180-lite SDRAM frequencies and SM8550 soundwire

   - Remoteproc firmware paths are corrected for Sony Xperia 10 IV"

* tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
  firmware: arm_ffa: Set handle field to zero in memory descriptor
  ARM: dts: Fix erroneous ADS touchscreen polarities
  arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
  arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
  arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
  EDAC/qcom: Get rid of hardcoded register offsets
  EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup()
  arm64: dts: qcom: sm8550: Use the correct LLCC register scheme
  dt-bindings: cache: qcom,llcc: Fix SM8550 description
  arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards
  arm64: dts: qcom: sm8550: use uint16 for Soundwire interval
  soc: qcom: rpmhpd: Add SA8155P power domains
  arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains
  dt-bindings: power: qcom,rpmpd: Add SA8155P
  soc: qcom: Rename ice to qcom_ice to avoid module name conflict
  soc: qcom: rmtfs: Fix error code in probe()
  soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe()
  ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
  ARM: at91: pm: fix imbalanced reference counter for ethernet devices
  arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths
  ...

Pull block fixes from Jens Axboe:

 - Fix an issue with the hardware queue nr_active, causing it to become
   imbalanced (Tian)

 - Fix an issue with null_blk not releasing pages if configured as
   memory backed (Nitesh)

 - Fix a locking issue in dasd (Jan)

* tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux:
  s390/dasd: Use correct lock while counting channel queue length
  null_blk: Fix: memory release when memory_backed=1
  blk-mq: fix blk_mq_hw_ctx active request accounting

Pull virtio bug fixes from Michael Tsirkin:
 "A bunch of fixes all over the place"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  tools/virtio: use canonical ftrace path
  vhost_vdpa: support PACKED when setting-getting vring_base
  vhost: support PACKED when setting-getting vring_base
  vhost: Fix worker hangs due to missed wake up calls
  vhost: Fix crash during early vhost_transport_send_pkt calls
  vhost_net: revert upend_idx only on retriable error
  vhost_vdpa: tell vqs about the negotiated
  vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister
  tools/virtio: Add .gitignore for ringtest
  tools/virtio: Fix arm64 ringtest compilation error
  vduse: avoid empty string for dev name
  vhost: use kzalloc() instead of kmalloc() followed by memset()

Pull ceph fixes from Ilya Dryomov:
 "A fix for a potential data corruption in differential backup and
  snapshot-based mirroring scenarios in RBD and a reference counting
  fixup to avoid use-after-free in CephFS, all marked for stable"

* tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client:
  ceph: fix use-after-free bug for inodes when flushing capsnaps
  rbd: get snapshot context after exclusive lock is ensured to be held
  rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting

The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit
583d6535 ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.

The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.

Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.

Fixes: 583d6535 ("dasd: remove dead code")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.comSigned-off-by: Jens Axboe <axboe@kernel.dk>

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix to avoid ISA-disallowed privilege mappings that can result from
   WRITE+EXEC mmap requests from userspace.

 - A fix for kfence to handle the huge pages.

 - A fix to avoid converting misaligned VAs to huge pages.

 - ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE has been selected so kprobe
   can understand user pointers.

* tag 'riscv-for-linus-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: fix kprobe __user string arg print fault issue
  riscv: Check the virtual alignment before choosing a map size
  riscv: Fix kfence now that the linear mapping can be backed by PUD/P4D/PGD
  riscv: mm: Ensure prot of VM_WRITE and VM_EXEC must be readable

Pull s390 fixes from Alexander Gordeev:

 - Avoid linker error for randomly generated config file that has
   CONFIG_BRANCH_PROFILE_NONE enabled and make it similar to riscv, x86
   and also to commit 4bf3ec38 ("s390: disable branch profiling for
   vdso").

 - Currently, if the device is offline and all the channel paths are
   either configured or varied offline, the associated subchannel gets
   unregistered. Don't unregister the subchannel, instead unregister
   offline device.

* tag 's390-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/purgatory: disable branch profiling
  s390/cio: unregister device when the only path is gone

Pull gpio fixes from Bartosz Golaszewski:
 "Two fixes for the GPIO testing module and one commit making Andy a
  reviewer for the GPIO subsystem:

   - fix a memory corruption bug in gpio-sim

   - fix inconsistencies in user-space configuration of gpio-sim

   - make Andy Shevchenko a reviewer for the GPIO subsystem"

* tag 'gpio-fixes-for-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  MAINTAINERS: add Andy Shevchenko as reviewer for the GPIO subsystem
  gpio: sim: quietly ignore configured lines outside the bank
  gpio: sim: fix memory corruption when adding named lines and unnamed hogs

The canonical location for the tracefs filesystem is at /sys/kernel/tracing.

But, from Documentation/trace/ftrace.rst:

  Before 4.1, all ftrace tracing control files were within the debugfs
  file system, which is typically located at /sys/kernel/debug/tracing.
  For backward compatibility, when mounting the debugfs file system,
  the tracefs file system will be automatically mounted at:

  /sys/kernel/debug/tracing

A few spots in tools/virtio still refer to this older debugfs
path, so let's update them to avoid confusion.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Message-Id: <20230215223350.2658616-6-zwisler@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>

Use the right structs for PACKED or split vqs when setting and
getting the vring base.

Fixes: 4c8cf318 ("vhost: introduce vDPA-based backend")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-4-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Use the right structs for PACKED or split vqs when setting and
getting the vring base.

Fixes: 4c8cf318 ("vhost: introduce vDPA-based backend")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-3-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Pull pin control fix from Linus Walleij:
 "A single fix for the Meson driver, nothing else has surfaced so far
  this cycle"

* tag 'pinctrl-v6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: meson-axg: add missing GPIOA_18 gpio group