- 27 Jun, 2024 31 commits
-
-
Geert Uytterhoeven authored
Overlay syntactic sugar for generating target-path fragments is supported by the version of dtc supplied with the kernel since commit 50aafd60 ("scripts/dtc: Update to upstream version v1.4.6-21-g84e414b0b5bc"). Hence convert the Bananapi R3 overlay devicetree source files to sugar syntax, improving readability. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/2fd900a30b5a0f7de4ea68f60bac250794b8cdb4.1716984213.git.geert+renesas@glider.beSigned-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
-
Pin-yen Lin authored
Set off-on-delay-us to 500000 us for pp3300_mipibrdg to make sure it complies with the panel's unprepare delay (the time to power down completely) of the power sequence. Explicit configuration on the regulator node is required because mt8192-asurada uses the same power supply for the panel and the anx7625 DP bridge. For example, the power sequence could be violated in this sequence: 1. Bridge on: panel goes off, but regulator doesn't turn off (refcount=1). 2. Bridge off: regulator turns off (refcount=0). 3. Bridge resume -> regulator turns on but the bridge driver doesn't check the delay. Or in this sequence: 1. Bridge on: panel goes off. The regulator doesn't turn off (refcount=1), but the .unprepared_time in panel_edp is still updated. 2. Bridge off, regulator goes off (refcount=0). 3. Panel on, but the panel driver uses the wrong .unprepared_time to check the unprepare delay. Fixes: f9f00b1f ("arm64: dts: mediatek: asurada: Add display regulators") Signed-off-by:
Pin-yen Lin <treapking@chromium.org> Reviewed-by:
-
Michael Walle authored
Add basic support for the Kontron 3.5" single board computer featuring a Mediatek i1200 SoC (MT8395/MT8195). Signed-off-by:
Michael Walle <mwalle@kernel.org> Reviewed-by:
-
Michael Walle authored
Add the compatible string for the Kontron 3.5"-SBC-i1200 single board computer. Signed-off-by:
Conor Dooley <conor.dooley@microchip.com> Reviewed-by:
-
Macpaul Lin authored
This patch fixes an issue where xhci1 was not functioning properly because the state and PHY settings were incorrect. The introduction of the 'force-mode' property in the phy-mtk-tphy driver allows for the correct initialization of xhci1 by updating the Device Tree settings accordingly. The necessary fixup which added support for the 'force-mode' switch in the phy-mtk-tphy driver. commit 9b273030 ("phy: mediatek: tphy: add support force phy mode switch") Link: https://lore.kernel.org/r/20231211025624.28991-2-chunfeng.yun@mediatek.com Prior to this fix, the system would exhibit the following probe failure messages for xhci1: xhci-mtk 11290000.usb: supply vbus not found, using dummy regulator xhci-mtk 11290000.usb: uwk - reg:0x400, version:104 xhci-mtk 11290000.usb: xHCI Host Controller xhci-mtk 11290000.usb: new USB bus registered, assigned bus number 5 xhci-mtk 11290000.usb: clocks are not stable (0x1003d0f) xhci-mtk 11290000.usb: can't setup: -110 xhci-mtk 11290000.usb: USB bus 5 deregistered xhci-mtk: probe of 11290000.usb failed with error -110 With the application of this dts fixup, the aforementioned initialization errors are resolved and xhci1 is working. Signed-off-by:
Macpaul Lin <macpaul.lin@mediatek.com> Link: https://lore.kernel.org/r/20240216095751.4937-1-macpaul.lin@mediatek.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
Add a devicetree for the Cherry Dojo (HP Chromebook x360 13b-ca0002sa) convertible type machine. Differences with the already supported Tomato machines include: - Different speaker amplifiers (Dual MAX98380, one per channel) - I2C Touchscreen is on a different address (though still a HID device) - Has NVMe storage on the PCIe0 controller - Slightly different keyboard top row keymap Link: https://lore.kernel.org/r/20240314103500.93158-3-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
Add the MT8195 Cherry platform's Dojo machine, a convertible design commercially known as the HP Chromebook x360 (13b-ca0002sa). Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240314103500.93158-2-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
The drivers and bindings acquired support for specifying audio hardware and links in device tree: describe and link the sound related HW of this machine. Link: https://lore.kernel.org/r/20240416071410.75620-19-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
The drivers and bindings acquired support for specifying audio hardware and links in device tree: describe and link the sound related HW of this machine. Link: https://lore.kernel.org/r/20240416071410.75620-18-angelogioacchino.delregno@collabora.comSigned-off-by:
-
Chen-Yu Tsai authored
The "mediatek,drive-strength-adv" pin config property has been deprecated in favor of the generic "drive-strength-microamp" property. Drop or convert all instances. A value of 0 disables the advanced mode, which is the hardware default. Signed-off-by:
Chen-Yu Tsai <wenst@chromium.org> Link: https://lore.kernel.org/r/20240412075516.1199846-1-wenst@chromium.orgSigned-off-by:
-
Chen-Yu Tsai authored
The "output-enable" property is set on uart1's RTS pin. This is bogus because the hardware does not actually have a controllable output buffer. Secondly, the implementation incorrectly treats this property as a request to switch the pin to GPIO output. This does not fit the intended semantic of "output-enable" and it does not have any affect either because the pin is muxed to the UART function, not the GPIO function. Drop the property. Fixes: cd894e27 ("arm64: dts: mt8183: Add krane-sku176 board") Signed-off-by:
-
AngeloGioacchino Del Regno authored
Add the necessary power supplies to safely enable CPU and GPU frequency scaling. Link: https://lore.kernel.org/r/20240409114211.310462-6-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
Enable the PCIe0 PHY to be able to set calibrations read from eFuses, improving the stability and performance of the PCIe link. While at it, also enable the T-PHYs for both PCIe1 and for USB, allowing the USB ports to finally switch to gadget mode if needed, and configure the VBUS/ID pins of both USB ports for the same. Link: https://lore.kernel.org/r/20240409114211.310462-5-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
The paris pinctrl driver supports specifying the RSEL drive strength in microamperes as well as internal bits definitions: choose to specify those in uA to avoid using hardware specific values in device trees. Link: https://lore.kernel.org/r/20240409114211.310462-4-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
GPIOs 25 and 26 do not support pull-up/pull-down when those are muxed as I2C6's SDA6/SCL6 lines: set those to bias-disable to avoid warning messages from the pinctrl driver. Fixes: 96564b1e ("arm64: dts: mediatek: Introduce the MT8395 Radxa NIO 12L board") Link: https://lore.kernel.org/r/20240409114211.310462-3-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
The thermal zones in MT8183 had cryptic names and all of them, apart from the cpu-thermal zone, had no thermal trips, hence those were not probed at all. Refactor the tzts1..5 and tztsABB thermal zones to add the correct thermal trips and give them a meaningful name, corresponding to the actually monitored thermal zone. While at it, also rename the thermal sensor node to "thermal-sensor". Now the thermal zones are probing and their temperatures can be read. Fixes: b325ce39 ("arm64: dts: mt8183: add thermal zone node") Link: https://lore.kernel.org/r/20240410083002.1357857-4-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
This SoC has two GPU related thermal zones: the primary zone must be called "gpu-thermal" for SVS to pick it up. Fixes: c7a72805 ("arm64: dts: mediatek: mt8192: Add thermal nodes and thermal zones") Link: https://lore.kernel.org/r/20240410083002.1357857-3-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
This SoC has two GPU related thermal zones: the primary zone must be called "gpu-thermal" for SVS to pick it up. Fixes: 1e5b6725 ("arm64: dts: mediatek: mt8195: Add AP domain thermal zones") Link: https://lore.kernel.org/r/20240410083002.1357857-2-angelogioacchino.delregno@collabora.comSigned-off-by:
-
Macpaul Lin authored
Add basic device-tree for the Genio 700 EVK board. The Genio 700 EVK is based on MediaTek MT8390 SoC. MT8390 hardware register maps are identical to MT8188. The Genio 700 EVK has following features: - MT8390 SoC - MT6365 PMIC - MT6319 Buck IC - 12V DC Jack - 2x4GB LPDDR4X - 64GB eMMC 5.1 - 64Mb SPI NOR - M.2 Key A-E slot with PCIe Gen2 and USB 2.0 - 2x DSI LCM ports - 2x touch sensor ports - 2x MIPI-CSI, as camera daughter board slots - USB 2 micro USB connector - USB 3 with 1 to 2 hub: - M.2 Key B slot - Type-C connector, with DisplayPort over Type-C - HDMI 2.0 TX port with Type A HDMI connector - eDP port - Gigabit Ethernet with RJ45 connector - SD card slot - Earphone Jack - Analog Microphone - 2x Digital Microphone - 3x UART with serial-to-usb converters and micro USB connectors Signed-off-by:
Chris-QJ Chen <chris-qj.chen@mediatek.com> Signed-off-by:
Pablo Sun <pablo.sun@mediatek.com> Signed-off-by:
-
Macpaul Lin authored
1. Add compatible for MT8390. 2. Add bindings for the MediaTek mt8390-evk board, also known as the "Genio 700-EVK". The MT8390 and MT8188 belong to the same SoC family, with only minor differences in their physical characteristics. They utilize unique efuse values for differentiation. The booting process and configurations are managed by boot loaders, firmware, and TF-A. Consequently, the part numbers and procurement channels vary. Signed-off-by:
-
Rafał Miłecki authored
MT7981 (Filogic 820) is a low cost version of MT7986 (Filogic 830) with the same watchdog controller. It also comes with on-SoC 802.11ax wireless. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Reviewed-by:
-
Rafał Miłecki authored
Add bindings of two on-SoC XHCI controllers. Signed-off-by:
-
AngeloGioacchino Del Regno authored
Add compatible for MT8188 VPP mutex, having different bits to activate mute for various hardware IPs. Acked-by:
-
AngeloGioacchino Del Regno authored
None of the MT8192 Chromebooks had their chassis-type specified: add the right definition for each. Reviewed-by:
David Heidelberg <david@ixit.cz> Link: https://lore.kernel.org/r/20240313141538.1438167-3-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
Define the chassis type on the remaining MT8183 Chromebooks. Link: https://lore.kernel.org/r/20240313141538.1438167-2-angelogioacchino.delregno@collabora.comSigned-off-by:
-
Daniel Danzberger authored
Introduce the Airoha EN7581 SoC's dtsi and the Airoha EN7581 Evaluation Board's dts file, as well as the required Makefiles. Reviewed-by:
Daniel Danzberger <dd@embedd.com> Co-developed-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Lorenzo Bianconi authored
Introduce Airoha EN7581 entry in Airoha dts binding. Acked-by:
-
Rafał Miłecki authored
Cudy WR3000 V1 is an MT7981B (AKA Filogic 820) based wireless router. It has 256 MiB of RAM, some LEDs & buttons and (not described yet) 4 Ethernet ports. Signed-off-by:
-
Rafał Miłecki authored
MT7981 contains on-SoC PIN controller that is also a GPIO provider. Signed-off-by:
-
Rafał Miłecki authored
Cudy WR3000 V1 is an MT7981B (AKA Filogic 820) based wireless router. Signed-off-by:
-
Rafał Miłecki authored
Cudy is a Chinese company providing networking products. Signed-off-by:
-
- 26 May, 2024 5 commits
-
-
Linus Torvalds authored
-
Kent Overstreet authored
percpu.h depends on smp.h, but doesn't include it directly because of circular header dependency issues; percpu.h is needed in a bunch of low level headers. This fixes a randconfig build error on mips: include/linux/alloc_tag.h: In function '__alloc_tag_ref_set': include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration] Reported-by:
kernel test robot <lkp@intel.com> Fixes: 24e44cc2 ("mm: percpu: enable per-cpu allocation tagging") Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/Signed-off-by:
Kent Overstreet <kent.overstreet@linux.dev> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools Pull perf tool fix from Arnaldo Carvalho de Melo: "Revert a patch causing a regression. This made a simple 'perf record -e cycles:pp make -j199' stop working on the Ampere ARM64 system Linus uses to test ARM64 kernels". * tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools: Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
-
Arnaldo Carvalho de Melo authored
This reverts commit 617824a7. This made a simple 'perf record -e cycles:pp make -j199' stop working on the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed at length in the threads in the Link tags below. The fix provided by Ian wasn't acceptable and work to fix this will take time we don't have at this point, so lets revert this and work on it on the next devel cycle. Reported-by:
Arnaldo Carvalho de Melo <acme@redhat.com>
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull smb client fixes from Steve French: - two important netfs integration fixes - including for a data corruption and also fixes for multiple xfstests - reenable swap support over SMB3 * tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: cifs: Fix missing set of remote_i_size cifs: Fix smb3_insert_range() to move the zero_point cifs: update internal version number smb3: reenable swapfiles over SMB3 mounts
-
- 25 May, 2024 4 commits
-
-
Linus Torvalds authored
Merge tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull misc fixes from Andrew Morton: "16 hotfixes, 11 of which are cc:stable. A few nilfs2 fixes, the remainder are for MM: a couple of selftests fixes, various singletons fixing various issues in various parts" * tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: mm/ksm: fix possible UAF of stable_node mm/memory-failure: fix handling of dissolved but not taken off from buddy pages mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again nilfs2: fix potential hang in nilfs_detach_log_writer() nilfs2: fix unexpected freezing of nilfs_segctor_sync() nilfs2: fix use-after-free of timer for log writer thread selftests/mm: fix build warnings on ppc64 arm64: patching: fix handling of execmem addresses selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages selftests/mm: compaction_test: fix bogus test success on Aarch64 mailmap: update email address for Satya Priya mm/huge_memory: don't unpoison huge_zero_folio kasan, fortify: properly rename memintrinsics lib: add version into /proc/allocinfo output mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Ingo Molnar: - Fix x86 IRQ vector leak caused by a CPU offlining race - Fix build failure in the riscv-imsic irqchip driver caused by an API-change semantic conflict - Fix use-after-free in irq_find_at_or_after() * tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after() genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Ingo Molnar: - Fix regressions of the new x86 CPU VFM (vendor/family/model) enumeration/matching code - Fix crash kernel detection on buggy firmware with non-compliant ACPI MADT tables - Address Kconfig warning * tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL crypto: x86/aes-xts - switch to new Intel CPU model defines x86/topology: Handle bogus ACPI tables correctly x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y
-
https://github.com/cminyard/linux-ipmiLinus Torvalds authored
Pull ipmi updates from Corey Minyard: "Mostly updates for deprecated interfaces, platform.remove and converting from a tasklet to a BH workqueue. Also use HAS_IOPORT for disabling inb()/outb()" * tag 'for-linus-6.10-1' of https://github.com/cminyard/linux-ipmi: ipmi: kcs_bmc_npcm7xx: Convert to platform remove callback returning void ipmi: kcs_bmc_aspeed: Convert to platform remove callback returning void ipmi: ipmi_ssif: Convert to platform remove callback returning void ipmi: ipmi_si_platform: Convert to platform remove callback returning void ipmi: ipmi_powernv: Convert to platform remove callback returning void ipmi: bt-bmc: Convert to platform remove callback returning void char: ipmi: handle HAS_IOPORT dependencies ipmi: Convert from tasklet to BH workqueue
-
