- Fix refcount leak in mtk_pcie_init_irq_domains() (Miaoqian Lin)

- Print decoded LTSSM state when the link doesn't come up (Jianjun Wang)

* pci/ctrl/mediatek-gen3:
  PCI: mediatek-gen3: Print LTSSM state when PCIe link down
  PCI: mediatek-gen3: Fix refcount leak in mtk_pcie_init_irq_domains()

- Add Airoha EN7532 to DT binding (John Crispin)

- Allow building of mediatek driver for ARCH_AIROHA (Felix Fietkau)

* pci/ctrl/mediatek:
  PCI: mediatek: Allow building for ARCH_AIROHA
  dt-bindings: PCI: mediatek: Add Airoha EN7532 support

- Wrap ARM64-specific MCFG quirks in #ifdef so Loongson can use the file
  (Huacai Chen)

- Use generic (not 32-bit only) config accesses for LS2K/LS7A (Huacai Chen)

- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)

- Avoid config reads to non-existent LS2K/LS7A devices because a hardware
  defect causes machine hangs (Huacai Chen)

- Work around LS7A integrated devices that report incorrect Interrupt Pin
  values (Jianmin Lv)

* pci/ctrl/loongson:
  PCI: loongson: Work around LS7A incorrect Interrupt Pin registers
  PCI: loongson: Don't access non-existent devices
  PCI: loongson: Add ACPI init support
  PCI: loongson: Use generic 8/16/32-bit config ops on LS2K/LS7A
  PCI/ACPI: Guard ARM64-specific mcfg_quirks

- Use bitmap API to allocate bitmaps instead of doing it by hand
  (Christophe JAILLET)

* pci/ctrl/iproc:
  PCI: iproc: Use bitmap API to allocate bitmaps

- Factor out ref clock disables to match enables (Bjorn Helgaas)

- Collect clock enables in imx6_pcie_clk_enable() (Richard Zhu)

- Propagate regulator and clock errors back to .host_init() caller (Richard
  Zhu)

- Disable i.MX6QDL clock when disabling ref clocks (Richard Zhu)

- Call host init function directly in resume instead of duplicating the
  code (Richard Zhu)

- Turn off regulators when suspending (Richard Zhu)

- Make link being down a non-fatal error so probe doesn't fail (Richard
  Zhu)

- Start link in resume only if it was up before suspend to reduce resume
  time (Richard Zhu)

- Move PHY init and power-on out of clock- and reset-related functions
  (Richard Zhu)

- Rework suspend callback to be more symmetric with resume (Richard Zhu)

- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)

- Allow speeds faster than Gen2 (Richard Zhu)

* pci/ctrl/imx6:
  PCI: imx6: Support more than Gen2 speed link mode
  PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
  PCI: imx6: Reformat suspend callback to keep symmetric with resume
  PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
  PCI: imx6: Disable clocks in reverse order of enable
  PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
  PCI: imx6: Reduce resume time by only starting link if it was up before suspend
  PCI: imx6: Mark the link down as non-fatal error
  PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
  PCI: imx6: Turn off regulator when system is in suspend mode
  PCI: imx6: Call host init function directly in resume
  PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
  PCI: imx6: Propagate .host_init() errors to caller
  PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
  PCI: imx6: Factor out ref clock disable to match enable
  PCI: imx6: Move imx6_pcie_clk_disable() earlier
  PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
  PCI: imx6: Move PHY management functions together
  PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
  PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()

- Remove unnecessary include files (Bjorn Helgaas)

* pci/ctrl/fu740:
  PCI: fu740: Remove unnecessary include files

- Move samsung phy-exynos-pcie init all to exynos5433_pcie_phy_init()
  instead of splitting across phy_init() and phy_power_on() (Marek
  Szyprowski)

- Call phy_init() before phy_power_on() for samsung phy-exynos-pcie, as
  required by the PHY programming model (Marek Szyprowski)

* pci/ctrl/exynos:
  PCI: exynos: Correct generic PHY usage
  phy: samsung: phy-exynos-pcie: sanitize init/power_on callbacks

- Remove unused struct dw_edma_chip.irq (Frank Li)

- Move eDMA private data from struct dw_edma to struct dw_edma_chip (Frank
  Li)

- Convert "struct dw_edma_region rg_region" to "void __iomem *reg_base"
  since only the virtual address (not physical address or size) is used
  (Frank Li)

- Rename "*_ch_cnt" to "ll_*_cnt" to reflect actual usage (Frank Li)

- Drop dma_slave_config.direction field usage (Serge Semin)

- Fix eDMA Rd/Wr-channels and DMA-direction semantics (Serge Semin)

- Add chip-specific DW_EDMA_CHIP_LOCAL flag to indicate that local eDMA
  doesn't require generating MSIs to remote (Frank Li)

- Enable DMA tests for endpoints that support it (Frank Li)

* pci/ctrl/dwc-edma:
  PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities
  dmaengine: dw-edma: Add support for chip-specific flags
  dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics
  dmaengine: dw-edma: Drop dma_slave_config.direction field usage
  dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip
  dmaengine: dw-edma: Change rg_region to reg_base in struct dw_edma_chip
  dmaengine: dw-edma: Detach the private data and chip info structures
  dmaengine: dw-edma: Remove unused irq field in struct dw_edma_chip

- Stop link on host_init errors and de-initialization (Serge Semin)

- Add support for unrolled iATU register space in dw_pcie_disable_atu()
  (Serge Semin)

- Disable outbound windows only for controllers that use iATU (Serge Semin)

- Set INCREASE_REGION_SIZE flag based on limit address, not on the size,
  since even a small size may cross a 4GB boundary (Serge Semin)

- Deallocate EPC memory on dw_pcie_ep_init() errors to avoid a leak (Serge
  Semin)

- Always enable CDM check if "snps,enable-cdm-check" exists instead of
  exiting early if the optional "num-lanes" was absent (Serge Semin)

- Simplify detection of whether we're using unrolled iATU registers (Serge
  Semin)

- Make dw_pcie_link_up() more generic by using dw_pcie_readl_dbi() instead
  of readl() (Serge Semin)

- Add dw_pcie_start_link() and dw_pcie_stop_link() wrappers to factor out
  checks for ops being implemented (Serge Semin)

- Move io_cfg_atu_shared to struct pcie_port and rename to cfg0_io_shared,
  since it's not used by dwc common code or dwc endpoint code (Serge Semin)

- Rename struct pcie_port to dw_pcie_rp to indicate that it's
  DesignWare-specific (Serge Semin)

- Drop unused struct dw_plat_pcie regmap pointer (Serge Semin)

- Fix some coding style issues (Serge Semin)

- Log link speed and width if it comes up (Serge Semin)

- Save DWC IP core version in native format as read from
  PORT_LOGIC.PCIE_VERSION_OFF register (Serge Semin)

- Read DWC IP core version from PORT_LOGIC.PCIE_VERSION_OFF (Serge Semin)

- Add macros to compare Synopsys IP core versions (Serge Semin)

- Drop manual DWC IP core version setup from intel-gw and tegra194 (Serge
  Semin)

- Add dw_pcie_ops.host_deinit() callback (Serge Semin)

- Drop enum dw_pcie_as_type in favor of PCIE_ATU_TYPE_MEM/IO (Serge Semin)

- Drop enum dw_pcie_region_type in favor of PCIE_ATU_REGION_DIR_IB/OB
  (Serge Semin)

- Simplify in/outbound iATU setup methods and reduce duplicated code (Serge
  Semin)

- Detect iATU region size from hardware (Serge Semin)

- Validate iATU outbound mappings against hardware constraints (Serge
  Semin)

- Check for errors in iATU setup (Serge Semin)

- Allocate a 32-bit DMA-able page to be MSI target instead of using a
  driver data structure that may not be addressable with 32-bit address
  (Will McVicker)

- Use the bitmap API to allocate bitmaps instead of open-coding it
  (Christophe JAILLET)

- Correct dw_pcie_free_msi() checking for when to remove IRQ handler and
  data (Dmitry Baryshkov)

- Split MSI init to new dw_pcie_msi_host_init() function (Dmitry Baryshkov)

- Convert struct pcie_port.msi_irq to an array so we can support more than
  32 MSI interrupts (Dmitry Baryshkov)

- Handle MSIs routed to multiple GIC interrupts for Qualcomm platforms with
  groups of 32 MSI vectors (Dmitry Baryshkov)

- Add additional MSI interrupts to qcom DT (Dmitry Baryshkov)

* pci/ctrl/dwc:
  dt-bindings: PCI: qcom: Support additional MSI vectors
  PCI: dwc: Handle MSIs routed to multiple GIC interrupts
  PCI: dwc: Convert struct pcie_port.msi_irq to an array
  PCI: dwc: Split MSI IRQ parsing/allocation to a separate function
  PCI: dwc: Correct msi_irq condition in dw_pcie_free_msi()
  PCI: dwc: Use the bitmap API to allocate bitmaps
  PCI: dwc: Fix MSI msi_msg DMA mapping
  PCI: dwc: Check iATU in/outbound range setup status
  PCI: dwc: Validate iATU outbound mappings against hardware constraints
  PCI: dwc: Add iATU regions size detection procedure
  PCI: dwc: Simplify in/outbound iATU setup methods
  PCI: dwc: Drop enum dw_pcie_region_type in favor of PCIE_ATU_REGION_DIR_IB/OB
  PCI: dwc: Drop enum dw_pcie_as_type in favor of PCIE_ATU_TYPE_MEM/IO
  PCI: dwc: Add dw_pcie_ops.host_deinit() callback
  PCI: tegra194: Drop manual DW PCIe controller version setup
  PCI: intel-gw: Drop manual DW PCIe controller version setup
  PCI: dwc: Add macros to compare Synopsys IP core versions
  PCI: dwc: Read DWC IP core version from register
  PCI: dwc: Use native DWC IP core version representation
  PCI: dwc: Detect iATU settings after getting "addr_space" resource
  PCI: dwc: Log link speed and width if it comes up
  PCI: dwc-plat: Drop dw_plat_pcie_of_match[] forward declaration
  PCI: dwc-plat: Drop unused regmap pointer
  PCI: dwc-plat: Simplify dw_plat_pcie_probe() return values
  PCI: dwc: Rename struct pcie_port to dw_pcie_rp
  PCI: dwc: Move io_cfg_atu_shared to struct pcie_port
  PCI: dwc: Add start_link/stop_link inlines
  PCI: dwc: Reuse local pointer to the resource data
  PCI: dwc: Organize local variable usage
  PCI: dwc: Convert dw_pcie_link_up() to use dw_pcie_readl_dbi()
  PCI: dwc: Simplify unrolled iATU detection
  PCI: dwc: Add newlines to log messages
  PCI: dwc: Add braces to multi-line if-else statements
  PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists
  PCI: dwc: Deallocate EPC memory on dw_pcie_ep_init() errors
  PCI: dwc: Set INCREASE_REGION_SIZE flag based on limit address
  PCI: dwc: Disable outbound windows only for controllers using iATU
  PCI: dwc: Add unroll iATU space support to dw_pcie_disable_atu()
  PCI: dwc: Stop link on host_init errors and de-initialization

- Remove unnecessary forward declarations (Jim Quinlan)

- Prevent config space access when link is down (Jim Quinlan)

- Split post-link up initialization to brcm_pcie_start_link() (Jim Quinlan)

- Enable child bus device regulators described under Root Ports in DT (Jim
  Quinlan)

- Disable/enable regulators in suspend/resume (Jim Quinlan)

- Rename .map_bus() functions to end with 'map_bus' as they do in other
  drivers (Jim Quinlan)

* pci/ctrl/brcmstb:
  PCI: brcmstb: Rename .map_bus() functions to end with 'map_bus'
  PCI: brcmstb: Disable/enable regulators in suspend/resume
  PCI: brcmstb: Enable child bus device regulators from DT
  PCI: brcmstb: Split post-link up initialization to brcm_pcie_start_link()
  PCI: brcmstb: Prevent config space access when link is down
  PCI: brcmstb: Remove unnecessary forward declarations

- Add support for AER capability on emulated bridge (Pali Rohár)

- Add support for Slot capability on emulated bridge (Pali Rohár)

* pci/ctrl/aardvark:
  PCI: aardvark: Fix reporting Slot capabilities on emulated bridge
  PCI: aardvark: Add support for AER registers on emulated bridge

- Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate the
  functions but don't advertise an ACS capability (Pavan Chebbi)

* pci/virtualization:
  PCI: Add ACS quirk for Broadcom BCM5750x NICs

- Replace sparc pci_mmap_page_range() wrapper.  This still leaves a
  sparc-specific pci_mmap_resource_range(), but it's only one interface
  instead of two (Arnd Bergmann)

- Remove sparc-specific pci_mmap_resource_range() by implementing
  pci_iobar_pfn().  This removes the ability to map the entire PCI I/O
  space using /proc/bus/pci, but we believe that's already been broken
  since v2.6.28 (Arnd Bergmann)

* pci/resource:
  sparc: Use generic pci_mmap_resource_range()
  PCI: Remove pci_mmap_page_range() wrapper

- Convert documentation examples to generic power management (Bjorn
  Helgaas)

* pci/pm:
  PCI/doc: Convert examples to generic power management

- Recognize disconnected devices so we don't bother trying to set them to
  "frozen" or "normal" state (Christoph Hellwig)

- Clear PCI Status register during enumeration in case firmware left errors
  logged (Kai-Heng Feng)

- Configure ECRC for every device, including hot-added ones (Stefan Roese)

- Keep AER error reporting enabled for switches (Stefan Roese)

- Enable error reporting for all devices that support AER (Stefan Roese)

- Iterate over error counters instead of error strings to avoid printing
  junk in AER sysfs counters (Mohamed Khalfella)

* pci/err:
  PCI/AER: Iterate over error counters instead of error strings
  PCI/AER: Enable error reporting when AER is native
  PCI/portdrv: Don't disable AER reporting in get_port_device_capability()
  PCI/AER: Configure ECRC for every device
  PCI: Clear PCI_STATUS when setting up device
  PCI/ERR: Recognize disconnected devices in report_error_detected()

- Split out ARI "next function" handling from the traditional one (Niklas
  Schnelle)

- Move jailhouse "isolated function" (non-zero functions where function 0
  doesn't exist) handling to pci_scan_slot() to avoid duplicating
  multi-function scanning in pci_scan_child_bus_extend() (Niklas Schnelle)

- Extend "isolated function" probing to s390 (Niklas Schnelle).

- Allow s390 zPCI zbus without a function 0 (Niklas Schnelle)

* pci/enumeration:
  s390/pci: allow zPCI zbus without a function zero
  PCI: Extend isolated function probing to s390
  PCI: Move jailhouse's isolated function handling to pci_scan_slot()
  PCI: Split out next_ari_fn() from next_fn()
  PCI: Clean up pci_scan_slot()

- Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)

* pci/endpoint:
  PCI: endpoint: Don't stop controller when unbinding endpoint function

- Remove pcie_aspm_pm_state_change(), which overwrites ASPM config on power
  state changes (Kai-Heng Feng)

* pci/aspm:
  PCI/ASPM: Unexport pcie_aspm_support_enabled()
  PCI/ASPM: Remove pcie_aspm_pm_state_change()

Support more than Gen2 speed link mode, since i.MX8MP PCIe supports up to
Gen3 link speed.

Link: https://lore.kernel.org/r/1658287576-26908-1-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The PCIE_DBI_RO_WR_EN bit should be set when write some DBI registers.  To
make sure that the DBI registers are writable, set the PCIE_DBI_RO_WR_EN
properly when writing the DBI registers.

Link: https://lore.kernel.org/r/1652866528-13220-1-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Create imx6_pcie_stop_link() and imx6_pcie_host_exit() functions.
Encapsulate clocks, regulators disables and PHY uninitialization into
imx6_pcie_host_exit().

To keep suspend/resume symmetric as much as possible, invoke these two
new created functions in suspend callback.

To be symmetric with imx6_pcie_host_exit(), move imx6_pcie_clk_enable()
to imx6_pcie_host_init() from imx6_pcie_deassert_core_reset().

Link: https://lore.kernel.org/r/1657783869-19194-18-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

Move the imx6_pcie_ltssm_disable() earlier and place it just behind the
imx6_pcie_ltssm_enable(), since it might not be only used by suspend
callback directly.

To be symmetric with imx6_pcie_ltssm_enable(), add the IMX6Q and IMX8MQ
switch cases in imx6_pcie_ltssm_disable().

Link: https://lore.kernel.org/r/1657783869-19194-17-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

imx6_pcie_clk_enable() enables clocks in the order:

  pcie_phy
  pcie_bus
  pcie
  imx6_pcie_enable_ref_clk

Change imx6_pcie_clk_disable() to disable them in the reverse order.

Link: https://lore.kernel.org/r/1657783869-19194-16-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>

Move the phy_power_on() to host_init from imx6_pcie_clk_enable().

Move the phy_init() to host_init from imx6_pcie_deassert_core_reset().

Refine the error handling in imx6_pcie_host_init() accordingly.

Link: https://lore.kernel.org/r/1657783869-19194-15-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

i.MX PCIe doesn't support hotplug. During resume, only start PCIe link
training when the link was up before system suspend to avoid the long
latency in the link training period.

Link: https://lore.kernel.org/r/1657783869-19194-14-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

If the PCIe link is down, return zero from imx6_pcie_start_link() so the
driver will probe successfully.

Link: https://lore.kernel.org/r/1657783869-19194-13-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

Move regulator enable out of imx6_pcie_deassert_core_reset(), since the
regulator_enable() has nothing to do with imx6_pcie_deassert_core_reset().

Link: https://lore.kernel.org/r/1657783869-19194-12-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The driver should undo any enables it did itself. The regulator disable
shouldn't be basing decisions on regulator_is_enabled().

Move the regulator_disable to the suspend function, turn off regulator when
the system is in suspend mode.

Link: https://lore.kernel.org/r/1657783869-19194-11-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Call imx6_pcie_host_init() instead of duplicating codes in resume.  Note
that this also means we do MPLL setup again during resume, which we didn't
do before.

[bhelgaas: add MPLL setup note, pointed out by Lucas]
Link: https://lore.kernel.org/r/1657783869-19194-10-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

When disabling PCIe clocks, disable i.MX6QDL ref clock too.

Link: https://lore.kernel.org/r/1657783869-19194-9-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

Since dw_pcie_host_init() checks for errors from ops->host_init(),
check for errors when enabling power regulators and clocks and return them.

[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1657783869-19194-8-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

Encapsulate the i.MX PCIe clock enable operations into one standalone
function, imx6_pcie_clk_enable().  No functional change intended.

[bhelgaas: split pure code moves into separate patches]
Link: https://lore.kernel.org/r/1657783869-19194-7-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

The PCIe ref clocks are specific to different variants.  The enables are
already split out into imx6_pcie_enable_ref_clk(), but the disables were
combined with the more generic bus/phy/pcie clock disables in
imx6_pcie_clk_disable().

Split out the variant-specific disables into imx6_pcie_disable_ref_clk() to
match imx6_pcie_enable_ref_clk().

No functional change intended.

Link: https://lore.kernel.org/r/1657783869-19194-6-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>

Move imx6_pcie_clk_disable() earlier to be near other clock-related
functions.  No functional change intended.

[bhelgaas: reorder patch so pure moves are earlier]
Link: https://lore.kernel.org/r/1657783869-19194-5-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

Move imx6_pcie_enable_ref_clk() earlier so it's not in the middle between
imx6_pcie_assert_core_reset() and imx6_pcie_deassert_core_reset().  No
functional change intended.

Link: https://lore.kernel.org/r/1657783869-19194-4-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>

Collect imx6_pcie_init_phy(), imx7d_pcie_wait_for_phy_pll_lock(), and
imx6_setup_phy_mpll() earlier with other PHY-related code.  No functional
change intended.

Link: https://lore.kernel.org/r/1657783869-19194-3-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>

Move imx6_pcie_grp_offset() and imx6_pcie_configure_type() earlier in the
file since they depend on nothing and are used by several other functions
that will be moved earlier.  No functional change intended.

Link: https://lore.kernel.org/r/1657783869-19194-2-git-send-email-hongxing.zhu@nxp.comSigned-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>

Replace SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() with NOIRQ_SYSTEM_SLEEP_PM_OPS(),
which has the advantage that the compiler always sees the PM callbacks as
referenced, so they don't need to be wrapped with "#ifdef CONFIG_PM_SLEEP"
or tagged with "__maybe_unused" to avoid "defined but not used" warnings.

See 1a3c7bb0 ("PM: core: Add new *_PM_OPS macros, deprecate old ones").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>

The proper initialization for generic PHYs is to call first phy_init(),
then phy_power_on().

While touching this, remove the phy_reset() call. It is just a left-over
from the obsoleted Exynos5440 support and the current exynos-pcie PHY
driver doesn't even support this function. It is also rarely used by other
drivers.

Link: https://lore.kernel.org/r/20220628220409.26545-2-m.szyprowski@samsung.comReported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

The exynos-pcie driver called phy_power_on() before phy_init() for some
historical reasons. However the generic PHY framework assumes that the
proper sequence is to call phy_init() first, then phy_power_on(). The
operations done by both functions should be considered as one action and as
such they are called by the exynos-pcie driver (without doing anything
between them). The initialization is just a sequence of register writes,
which cannot be altered without breaking the hardware operation.

To match the generic PHY framework requirement, simply move all register
writes to the phy_init()/phy_exit() and drop power_on()/power_off()
callbacks. This way the driver will also work with the old (incorrect)
PHY initialization call sequence.

Link: https://lore.kernel.org/r/20220628220409.26545-1-m.szyprowski@samsung.comReported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>