Commit 70d57139 authored by Larry Finger's avatar Larry Finger Committed by John W. Linville

rtl8187: Fix wrong rfkill switch mask for some models

There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.

This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: default avatarLarry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: default avatarAntti Kaijanmäki <antti@kaijanmaki.net>
Tested-by: default avatarHin-Tak Leung <hintak.leung@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent 815833e7
......@@ -23,6 +23,7 @@
#define RTL8187_EEPROM_TXPWR_CHAN_1 0x16 /* 3 channels */
#define RTL8187_EEPROM_TXPWR_CHAN_6 0x1B /* 2 channels */
#define RTL8187_EEPROM_TXPWR_CHAN_4 0x3D /* 2 channels */
#define RTL8187_EEPROM_SELECT_GPIO 0x3B
#define RTL8187_REQT_READ 0xC0
#define RTL8187_REQT_WRITE 0x40
......@@ -31,6 +32,9 @@
#define RTL8187_MAX_RX 0x9C4
#define RFKILL_MASK_8187_89_97 0x2
#define RFKILL_MASK_8198 0x4
struct rtl8187_rx_info {
struct urb *urb;
struct ieee80211_hw *dev;
......@@ -122,6 +126,7 @@ struct rtl8187_priv {
u8 noise;
u8 slot_time;
u8 aifsn[4];
u8 rfkill_mask;
struct {
__le64 buf;
struct sk_buff_head queue;
......
......@@ -1322,6 +1322,7 @@ static int __devinit rtl8187_probe(struct usb_interface *intf,
struct ieee80211_channel *channel;
const char *chip_name;
u16 txpwr, reg;
u16 product_id = le16_to_cpu(udev->descriptor.idProduct);
int err, i;
dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops);
......@@ -1481,6 +1482,13 @@ static int __devinit rtl8187_probe(struct usb_interface *intf,
(*channel++).hw_value = txpwr & 0xFF;
(*channel++).hw_value = txpwr >> 8;
}
/* Handle the differing rfkill GPIO bit in different models */
priv->rfkill_mask = RFKILL_MASK_8187_89_97;
if (product_id == 0x8197 || product_id == 0x8198) {
eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_SELECT_GPIO, &reg);
if (reg & 0xFF00)
priv->rfkill_mask = RFKILL_MASK_8198;
}
/*
* XXX: Once this driver supports anything that requires
......@@ -1509,9 +1517,9 @@ static int __devinit rtl8187_probe(struct usb_interface *intf,
mutex_init(&priv->conf_mutex);
skb_queue_head_init(&priv->b_tx_status.queue);
printk(KERN_INFO "%s: hwaddr %pM, %s V%d + %s\n",
printk(KERN_INFO "%s: hwaddr %pM, %s V%d + %s, rfkill mask %d\n",
wiphy_name(dev->wiphy), dev->wiphy->perm_addr,
chip_name, priv->asic_rev, priv->rf->name);
chip_name, priv->asic_rev, priv->rf->name, priv->rfkill_mask);
#ifdef CONFIG_RTL8187_LEDS
eeprom_93cx6_read(&eeprom, 0x3F, &reg);
......
......@@ -25,10 +25,10 @@ static bool rtl8187_is_radio_enabled(struct rtl8187_priv *priv)
u8 gpio;
gpio = rtl818x_ioread8(priv, &priv->map->GPIO0);
rtl818x_iowrite8(priv, &priv->map->GPIO0, gpio & ~0x02);
rtl818x_iowrite8(priv, &priv->map->GPIO0, gpio & ~priv->rfkill_mask);
gpio = rtl818x_ioread8(priv, &priv->map->GPIO1);
return gpio & 0x02;
return gpio & priv->rfkill_mask;
}
void rtl8187_rfkill_init(struct ieee80211_hw *hw)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment