rtl8187: Fix wrong rfkill switch mask for some models

There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.

This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: Antti Kaijanmäki <antti@kaijanmaki.net>
Tested-by: Hin-Tak Leung <hintak.leung@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/rtl818x/rtl8187.h

@@ -23,6 +23,7 @@
 #define RTL8187_EEPROM_TXPWR_CHAN_1	0x16	/* 3 channels */
 #define RTL8187_EEPROM_TXPWR_CHAN_6	0x1B	/* 2 channels */
 #define RTL8187_EEPROM_TXPWR_CHAN_4	0x3D	/* 2 channels */
+#define RTL8187_EEPROM_SELECT_GPIO	0x3B
 
 #define RTL8187_REQT_READ	0xC0
 #define RTL8187_REQT_WRITE	0x40
@@ -31,6 +32,9 @@
 
 #define RTL8187_MAX_RX		0x9C4
 
+#define RFKILL_MASK_8187_89_97	0x2
+#define RFKILL_MASK_8198	0x4
+
 struct rtl8187_rx_info {
 	struct urb *urb;
 	struct ieee80211_hw *dev;
@@ -122,6 +126,7 @@ struct rtl8187_priv {
 	u8 noise;
 	u8 slot_time;
 	u8 aifsn[4];
+	u8 rfkill_mask;
 	struct {
 		__le64 buf;
 		struct sk_buff_head queue;

drivers/net/wireless/rtl818x/rtl8187_dev.c

@@ -1322,6 +1322,7 @@ static int __devinit rtl8187_probe(struct usb_interface *intf,
 	struct ieee80211_channel *channel;
 	const char *chip_name;
 	u16 txpwr, reg;
+	u16 product_id = le16_to_cpu(udev->descriptor.idProduct);
 	int err, i;
 
 	dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops);
@@ -1481,6 +1482,13 @@ static int __devinit rtl8187_probe(struct usb_interface *intf,
 		(*channel++).hw_value = txpwr & 0xFF;
 		(*channel++).hw_value = txpwr >> 8;
 	}
+	/* Handle the differing rfkill GPIO bit in different models */
+	priv->rfkill_mask = RFKILL_MASK_8187_89_97;
+	if (product_id == 0x8197 || product_id == 0x8198) {
+		eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_SELECT_GPIO, &reg);
+		if (reg & 0xFF00)
+			priv->rfkill_mask = RFKILL_MASK_8198;
+	}
 
 	/*
 	 * XXX: Once this driver supports anything that requires
@@ -1509,9 +1517,9 @@ static int __devinit rtl8187_probe(struct usb_interface *intf,
 	mutex_init(&priv->conf_mutex);
 	skb_queue_head_init(&priv->b_tx_status.queue);
 
-	printk(KERN_INFO "%s: hwaddr %pM, %s V%d + %s\n",
+	printk(KERN_INFO "%s: hwaddr %pM, %s V%d + %s, rfkill mask %d\n",
 	       wiphy_name(dev->wiphy), dev->wiphy->perm_addr,
-	       chip_name, priv->asic_rev, priv->rf->name);
+	       chip_name, priv->asic_rev, priv->rf->name, priv->rfkill_mask);
 
 #ifdef CONFIG_RTL8187_LEDS
 	eeprom_93cx6_read(&eeprom, 0x3F, &reg);

drivers/net/wireless/rtl818x/rtl8187_rfkill.c

@@ -25,10 +25,10 @@ static bool rtl8187_is_radio_enabled(struct rtl8187_priv *priv)
 	u8 gpio;
 
 	gpio = rtl818x_ioread8(priv, &priv->map->GPIO0);
-	rtl818x_iowrite8(priv, &priv->map->GPIO0, gpio & ~0x02);
+	rtl818x_iowrite8(priv, &priv->map->GPIO0, gpio & ~priv->rfkill_mask);
 	gpio = rtl818x_ioread8(priv, &priv->map->GPIO1);
 
-	return gpio & 0x02;
+	return gpio & priv->rfkill_mask;
 }
 
 void rtl8187_rfkill_init(struct ieee80211_hw *hw)