platform_get_irq() returns a negative value on error, not 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Having the thermometer on during channel configuration
could cause tuning instability.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz.  In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner.  Move the IF notch configuration to after we update MPD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:

tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5

Now, instead of reporting an invalid ID, it will report the correct error:

tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed

A possible improvement would be trying to reset the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:

DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed

Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.

With this patch, it will now print:

Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed

Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Describe exactly that only s-video and composite input are working on Avermedia
A700
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

On some alsa versions, it seems that snd_pcm_substream_chip(substream)
is returning a NULL pointer. This causes an OOPS, as reported by:

https://bugs.launchpad.net/ubuntu/+source/linux-ubuntu-modules-2.6.24/+bug/212271
https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/212960

This patch avoids the OOPS by not letting and open() succeed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

decrementing dev->empress_users should be done as last action of ts_release,
because it sleeps and write access to dev->empress_started is not protected
in any way
(additionally closing thread could mute audio after opening thread unmuted it)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

If I try v4l2-ctl --all -d /dev/video1 or v4l2-ctl --streamon -d /dev/video1
modules crashed:

*pde = 00000000
Modules linked in: ac battery loop saa7134_empress(F) saa6752hs(F) tuner_simple(F) tuner_types(F) tea5767(F) tda9887(F) tda8290(F) tea5761(F) tuner(F) snd_cmipci snd_pcm snd_page_alloc snd_opl3_lib saa7134(F) snd_mpu401 parport_pc parport snd_timer snd_hwdep snd_mpu401_uart floppy rtc psmouse videodev(F) v4l1_compat(F) compat_ioctl32(F) v4l2_common(F) videobuf_dma_sg(F) videobuf_core(F) snd_rawmidi snd_seq_device via_ircc pcspkr snd ir_kbd_i2c(F) irda soundcore ir_common(F) crc_ccitt tveeprom(F) i2c_viapro i2c_core button via_agp agpgart evdev ext3 jbd mbcache ide_cd_mod cdrom ide_disk 8139cp via82cxxx ide_core 8139too mii ehci_hcd uhci_hcd usbcore thermal processor fan

EIP is at __mutex_lock_slowpath+0x29/0x7b
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process v4l2-ctl (pid: 2742, ti=ced7e000 task=cf325260 task.ti=ced7e000)
       d08e5411 00000000 ced7fed4 00000000 d0975acb 40045612 cfa86ee0 ffffffcd
       cf2b7000 ced7febc c03858d6 00000019 00000292 d089e4ec cf37b2a0 d089e4a0
Call Trace:
 [<c028b52b>] mutex_lock+0xa/0xb
 [<d08e5411>] videobuf_streamon+0xf/0x9a [videobuf_core]
 [<d0975acb>] __video_do_ioctl+0x136a/0x2d68 [videodev]
 [<d088f789>] task_end_request+0x40/0x51 [ide_core]
 [<d088c4aa>] ide_intr+0x187/0x192 [ide_core]
 [<c016a551>] mntput_no_expire+0x11/0x64
 [<c0160b1c>] path_walk+0x90/0x98
 [<d0977738>] video_ioctl2+0x173/0x239 [videodev]
 [<c0140936>] filemap_fault+0x202/0x370
 [<c014930a>] __do_fault+0x2c3/0x2fe
 [<c014ab03>] handle_mm_fault+0x22a/0x49f
 [<c0162737>] vfs_ioctl+0x47/0x5d
 [<c0162992>] do_vfs_ioctl+0x245/0x258
 [<c01629e6>] sys_ioctl+0x41/0x5b
 [<c01036a6>] sysenter_past_esp+0x5f/0x85
 =======================

After this fix all of that commands works without problem:

v4l2-ctl --all -d /dev/video1

Driver Info:
	Driver name   : saa7134
	Card type     : Beholder BeholdTV M6 Extra
	Bus info      : PCI:0000:00:0d.0
	Driver version: 526
	Capabilities  : 0x05000001
		Video Capture
		Read/Write
		Streaming
Format Video Capture:
	Width/Height  : 720/576
	Pixel Format  : MPEG
	Field         : Any
	Bytes per Line: 0
	Size Image    : 58656
	Colorspace    : Unknown (00000000)
Video input : 0 (CCIR656)
Video Standard = 0x000000ff
	PAL-B/B1/G/H/I/D/D1/K


P.S. data from /dev/video1 is not correct :(( .
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx-cards.c
em28xx-reg.h
 - Add em2860 chip ID (seen on Pointnix Intra-Oral Camera)
   http://www.pointnix.com/ENG/dental/product_02.aspSigned-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx-audio.c
em28xx-dvb.c
 - Em28xx extensions should ensure they are being only loaded against devices
   that support them.  Deals with case where there are multiple em28xx
   devices, some of which have DVB (or ALSA) support and some do not.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

- change msleep(0) to msleep(1)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

- remove useless identify_state - device is always warm
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

- add little sleep to avoid I2C errors arising on faster CPUs
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx-cards.c
 - DVB support is supposed to be enabled for the first generation HVR-900.
   This device was confirmed with DVB by mkrufky when we did the original work
   in April, but I guess we forgot to set the flag.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx-video.c
 - Properly handle loading of the module when multiple devices are already
   connected (such as at bootup).  Before we were only calling dvb_init()
   against the last device in the list, so while we were handling subsequent
   adds properly, if there were multiple devices present on driver load,
   everybody except the last device would not get initialized.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

cx18-cards.h had a copy of the audio and video input enums
from cx18-av-core.h, but with different prefixes. Removed
that copy and used the ones from cx18-av-core.h.

Thanks to Andy Walls <awalls@radix.net> for the report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The S-Video LUMA input was restricted to the In1-In4 inputs, but it
turns out that it can use the full range of In1-In8.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Thanks to timf <timf@iinet.net.au> and Mike Galbraith <efault@gmx.de> to report
this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

As reported by Ingo Molnar:
MODPOST 346 modules
ERROR: "input_free_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined!
ERROR: "input_register_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined!
ERROR: "input_allocate_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined!
ERROR: "input_unregister_device" [drivers/media/dvb/ttpci/budget-ci.ko] undefined!
ERROR: "input_event" [drivers/media/common/ir-common.ko] undefined!

This occurs when:

CONFIG_INPUT=n
CONFIG_VIDEO_IR=m
CONFIG_DVB_BUDGET_CI=m

Thanks-to: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()
  [IA64] Handle count==0 in sn2_ptc_proc_write()
  [IA64] Fix boot failure on ia64/sn2

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  [GFS2] fix gfs2 block allocation (cleaned up)
  [GFS2] BUG: unable to handle kernel paging request at ffff81002690e000

* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: Remove now unused structs from kvm_para.h
  x86: KVM guest: Use the paravirt clocksource structs and functions
  KVM: Make kvm host use the paravirt clocksource structs
  x86: Make xen use the paravirt clocksource structs and functions
  x86: Add structs and functions for paravirt clocksource
  KVM: VMX: Fix host msr corruption with preemption enabled
  KVM: ioapic: fix lost interrupt when changing a device's irq
  KVM: MMU: Fix oops on guest userspace access to guest pagetable
  KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend)
  KVM: MMU: Fix rmap_write_protect() hugepage iteration bug
  KVM: close timer injection race window in __vcpu_run
  KVM: Fix race between timer migration and vcpu migration

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  Revert "[WATCHDOG] hpwdt: Add CFLAGS to get driver working"

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  xen: remove support for non-PAE 32-bit

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  kgdb: sparse fix
  kgdb: documentation update - remove kgdboe

On 9xx chips, bus mastering needs to be enabled at resume time for much of the
chip to function.  With this patch, vblank interrupts will work as expected
on resume, along with other chip functions.   Fixes kernel bugzilla #10844.
Signed-off-by: Jie Luo <clotho67@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kvm_* structs are obsoleted by the pvclock_* ones.
Now all users have been switched over and the old structs
can be dropped.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch updates the kvm host code to use the pvclock structs
and functions, thereby making it compatible with Xen.

The patch also fixes an initialization bug: on SMP systems the
per-cpu has two different locations early at boot and after CPU
bringup.  kvmclock must take that in account when registering the
physical address within the host.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch updates the kvm host code to use the pvclock structs.
It also makes the paravirt clock compatible with Xen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch updates the xen guest to use the pvclock structs
and helper functions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch adds structs for the paravirt clocksource ABI
used by both xen and kvm (pvclock-abi.h).

It also adds some helper functions to read system time and
wall clock time from a paravirtual clocksource (pvclock.[ch]).
They are based on the xen code.  They are enabled using
CONFIG_PARAVIRT_CLOCK.

Subsequent patches of this series will put the code in use.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

This patch fixes bz 450641.

This patch changes the computation for zero_metapath_length(), which it
renames to metapath_branch_start(). When you are extending the metadata
tree, The indirect blocks that point to the new data block must either
diverge from the existing tree either at the inode, or at the first
indirect block. They can diverge at the first indirect block because the
inode has room for 483 pointers while the indirect blocks have room for
509 pointers, so when the tree is grown, there is some free space in the
first indirect block. What metapath_branch_start() now computes is the
height where the first indirect block for the new data block is located.
It can either be 1 (if the indirect block diverges from the inode) or 2
(if it diverges from the first indirect block).
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

As noted by Akinobu Mita alloc_bootmem and related functions never return
NULL and always return a zeroed region of memory.  Thus a NULL test or
memset after calls to these functions is unnecessary.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Luck <tony.luck@intel.com>

The fix applied in e0c6d97c
"security hole in sn2_ptc_proc_write" didn't take into account
the case where count==0 (which results in a buffer underrun
when adding the trailing '\0').  Thanks to Andi Kleen for
pointing this out.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Call check_sal_cache_flush() after platform_setup() as
check_sal_cache_flush() now relies on being able to call platform
vector code.

Problem was introduced by: 3463a93d
"Update check_sal_cache_flush to use platform_send_ipi()"
Signed-off-by: Jes Sorensen <jes@sgi.com>
Tested-by: Alex Chiang: <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

- Fix warning reported by sparse
kernel/kgdb.c:1502:6: warning: symbol 'kgdb_console_write' was not declared.
	Should it be static?
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>