Factor out ide_dma_sff_write_status(), symmetric to ide_dma_sff_read_status().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move apparently misplaced read_sff_dma_status() method from 'struct ide_tp_ops'
to 'struct ide_dma_ops', renaming it to dma_sff_read_status() and making only
required for SFF-8038i compatible IDE controller drivers (greatly cutting down
the number of initializers) as its only user (outside ide-dma-sff.c and such
drivers) appears to be ide_pci_check_simplex() which is only called for such
controllers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Replace setting of 'hwif->dma_ops' in the 'alim15x3' and 'palm_bk3710' drivers'
init_dma() methods with initializing the corresponding member of their 'struct
ide_port_info' instances and remove such setting from the 'hpt366' driver that
just doesn't use 'sff_dma_ops'. Along with some code save, this prepares us for
the next patch...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Support for the IT8172 IDE controller was removed from the kernel
sometime after 2.6.18.  Support for the only boards that used the IT8172
was removed from the kernel after 2.6.18, as they had never compiled
since 2.6.0.  However, there are a couple of platforms that use this
chip: the PMC-Sierra Xiao Hu thin-client computer, which is no longer
in production, and the Linksys NSS4000 Network Attached Storage box,
which is based on the Xiao Hu board.  I am attempting to add support
for the Xiao Hu to the kernel, and this IT8172 IDE controller is the
first bit of code in this effort.

This patch resurrects the IT8172 IDE controller code.  I began with
the 2.6.18 version of the it8172.c file, and have moved it forward so
that it works with the latest version of the kernel.  I have run this
driver on a PMC-Sierra Xiao Hu board with the 2.6.28 kernel, and
I have had no problems with it in my configuration.  The attached patch
applies cleanly against 2.6.28.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: alan@lxorguk.ukuu.org.uk
[bart: s/HWIF(drive)/drive->hwif/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Allows UDMA > 33 on ACER TM290 and ACER Aspire 1694WLMi.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This makes ide_port_scan()'s behavior match ide_host_register()'s
one and fixes OOPS in elv_may_queue() during port re-scan.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* ->cur_dev should now be always valid if ->handler is set so
  remove redundant checks from ide_intr() and ide_timer_expiry().

* Apply CodingStyle fixups in ide_timer_expiry() while at it.

There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If ->handler is set while it shouldn't be it indicates deep problems
so BUG_ON()-ning and preventing further damage is much more appropriate
than merely printing an error message.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

... and remove no longer needed cdrom_start_packet_command and
cdrom_transfer_packet_command.

Tested lightly with ide-cd and ide-floppy.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

as it is done for all other IDE ATAPI devices.

There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

... instead of assuming it is set for accelerated DRQ type devices.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

According the documentation, id[ATA_ID_DWORD_IO] is non-zero if
the drive supports dword IO, while the code disables support by
setting IDE_DFLAG_NO_IO_32BIT. In addition, this word has been
reused by the ATA8 specification. This patch fixes both cases.
Signed-off-by: Mario Schwalbe <schwalbe@inf.tu-dresden.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove id[ATA_ID_DWORD_IO] check altogether per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_port_for_each_dev() / ide_host_for_each_port() iterators
and update IDE code to use them.

While at it:
- s/unit/i/ variable in ide_port_wait_ready(), ide_probe_port(),
  ide_port_tune_devices(), ide_port_init_devices_data(), do_reset1(),
  ide_acpi_set_state() and scc_dma_end()
- s/d/i/ variable in ide_proc_port_register_devices()

There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Allocate device structures dynamically instead of having them embedded
in ide_hwif_t:

* Remove needless zeroing of port structure from ide_init_port_data().

* Add ide_hwif_t.devices[MAX_DRIVES] (table of pointers to the devices).

* Add ide_port_{alloc,free}_devices() helpers and use them respectively
  in ide_{host,free}_alloc().

* Convert all users of ->drives[] to use ->devices[] instead.

While at it:

* Use drive->dn for the slave device check in scc_pata.c.

As a nice side-effect this patch cuts ~1kB (x86-32) from the resulting
code size:

   text    data     bss     dec     hex filename
  53963    1244     237   55444    d894 drivers/ide/ide-core.o.before
  52981    1244     237   54462    d4be drivers/ide/ide-core.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

kzalloc() -> kzalloc_node() in ide_host_alloc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Because presence of the peer device was not checked in
it821x_set_pio_mode() PIO0 mode was used for taskfile PIO
in single device configurations.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove (now superfluous) ->error method from struct ide_driver.

* Unexport __ide_error() and make it static.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- s/struct ide_driver_s/struct ide_driver/
- use to_ide_driver() macro in ide-proc.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Just use u8 instead, also s/__u8/u8/ in ide-cd.h while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove needless parens while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move IDE_DEFAULT_MAX_FAILURES to <linux/ide.h>.

* Move ide_cfg_mtx, ide_hwif_to_major[], ide_port_init_devices_data(),
  ide_init_port_data(), ide_init_port_hw() and ide_unregister() to
  ide-probe.c from ide.c.

* Make ide_unregister(), ide_init_port_data(), ide_init_port_hw()
  and ide_cfg_mtx static.

While at it:

* Remove stale ide_init_port_data() documentation and ide_lock extern.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Merge ide_hwgroup_t with ide_hwif_t.

* Cleanup init_irq() accordingly, then remove no longer needed
  ide_remove_port_from_hwgroup() and ide_ports[].

* Remove now unused HWGROUP() macro.

While at it:

* ide_dump_ata_error() fixups

v2:
* Fix ->quirk_list check in do_ide_request()
  (s/hwif->cur_dev/prev_port->cur_dev).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->host_busy field to struct ide_host and use it's first bit
  together with lock bitops to provide new ports serialization method.

* Convert core IDE code to use new ide_[un]lock_host() helpers.

  This removes the need for taking hwgroup->lock if host is already
  busy on serialized hosts and makes it possible to merge ide_hwgroup_t
  into ide_hwif_t (done in the later patch).

* Remove no longer needed ide_hwgroup_t.busy and ide_[un]lock_hwgroup().

* Update do_ide_request() documentation.

v2:
* ide_release_lock() should be called inside IDE_HFLAG_SERIALIZE check.

* Add ide_hwif_t.busy flag and ide_[un]lock_port() for serializing
  devices on a port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'int port_count' field to ide_hwgroup_t to keep the track
  of the number of ports in the hwgroup.  Then update init_irq()
  and ide_remove_port_from_hwgroup() to use it.

* Remove no longer needed hwgroup->hwif, {drive,hwif}->next,
  ide_add_drive_to_hwgroup() and ide_remove_drive_from_hwgroup()
  (hwgroup->drive now only denotes the currently active device
   in the hwgroup).

* Update locking documentation in <linux/ide.h>.

While at it:

* Rename ->drive field in ide_hwgroup_t to ->cur_dev.

* Use __func__ in ide_timer_expiry().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use hwif instead of hwgroup as {request,free}_irq()'s cookie,
teach ide_intr() to return early for non-active serialized ports,
modify unexpected_intr() accordingly and then use per-port IRQ
handlers instead of per-hwgroup ones.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Pass 'ide_hwif_t *' instead of 'ide_hwgroup_t *' to unexpected_intr().

* Cache pointer to the port currently being serviced in ->cur_port
  and use it instead of hwif->hwgroup on serialized hosts.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix do_ide_request() to operate on previous device / port instead of
the current one.  The original code was wrong since at least Feb 2002
(2.4.0 timeframe).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

commit 295f0004 ("ide: don't execute
the next queued command from the hard-IRQ context") overlooked that
ide_do_drive_cmd() (used for REQUEST SENSE command handling) may still
invoke do_ide_request() (->request_fn) in the hard-IRQ context through
blk_start_queueing().  This resulted in a LOCKDEP warning after commit
b599bc7a1199419e122cb2e9ec6b0fa2cfbbc17b ("ide: use per-device request
queue locks (v2)").

Since calling blk_start_queuing() in ide_do_drive_cmd() doesn't make
much sense as the port is already marked as busy (so the execution of
the new command will be deferred anyway) then just remove it fixing
LOCKDEP warning and saving some CPU cycles at the same time.
Reported-and-tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Grissiom <chaos.proton@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>