- 16 Mar, 2018 2 commits
-
-
Chris Zhong authored
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence only one PHY can connect to DP controller at one time, the other should be disconnected. The GRF_SOC_CON26 register has a switch bit to do it, set this bit means enable PHY 1, clear this bit means enable PHY 0. If the board has 2 Type-C ports, the DP driver get the phy id from devm_of_phy_get_by_index, and then control this switch according to this id. But some others board only has one Type-C port, it may be PHY 0 or PHY 1. The dts node id can not tell us the correct PHY id. Hence move this switch to PHY driver, the PHY driver can distinguish between PHY 0 and PHY 1, and then write the correct register bit. Signed-off-by:
Chris Zhong <zyw@rock-chips.com> Signed-off-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> [The phy-changes are in the phy-tree now and the cdn-dp wasn't enabled at all so far, so this change can go through drm-misc alone without causing issues when testing drm-misc] Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20180216120956.19034-6-enric.balletbo@collabora.com
-
Joe Perches authored
drm_printk is used for both DRM_ERROR and DRM_DEBUG with unnecessary arguments that can be removed by creating separate functins. Create specific functions for these calls to reduce x86/64 defconfig size by ~20k. Modify the existing macros to use the specific calls. new: $ size -t drivers/gpu/drm/built-in.a | tail -1 1876562 44542 995 19220999 1d5433 (TOTALS) old: $ size -t drivers/gpu/drm/built-in.a | tail -1 1897565 44542 995 1943102 1da63e (TOTALS) Miscellanea: o intel_display requires a change to use the specific calls. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/016b5cb84cede20fd0f91ed6965421d99fd5f2ce.1520978414.git.joe@perches.com
-
- 15 Mar, 2018 1 commit
-
-
Fabio Estevam authored
The cable_plugin member never receives an assignment, so it is always false, which causes hdmi_enable_overflow_interrupts() to never be called as per the logic below: if (hdmi->cable_plugin && hdmi->sink_is_hdmi) hdmi_enable_overflow_interrupts(hdmi); This has been the case since the driver was originally introduced in commit 9aaf880e ("imx-drm: Add mx6 hdmi transmitter support"). Remove the cable_plugin element and the hdmi_enable_overflow_interrupts() function that is never called. Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # On R-Car H3 Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1518812170-22687-1-git-send-email-festevam@gmail.com
-
- 14 Mar, 2018 14 commits
-
-
Haneen Mohammed authored
This patch replace instances of drm_framebuffer_unreference with _put() suffix, because it is shorter and consistent with the kernel use of *_get/put() suffixes. This was done with the following Coccinelle script: @r@ expression e; @@ ( -drm_framebuffer_reference(e); +drm_framebuffer_get(e); | -drm_framebuffer_unreference(e); +drm_framebuffer_put(e); ) Signed-off-by:
Haneen Mohammed <hamohammed.sa@gmail.com> Acked-by:
Sinclair Yeh <syeh@vmware.com> Signed-off-by:
-
Marc Zyngier authored
The rockchip DRM driver is quite careful to disable interrupts when taking a lock that is also taken in interrupt context, which is a good thing. What is a bit over the top is to use spin_lock_irqsave when already in interrupt context, as you cannot take another interrupt again, and disabling interrupt is just pure overhead. Switching to the non _irqsave version in interrupt context is more logical, and less heavy handed. Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Marc Zyngier authored
memcpy is only meant to be used for memory, and only that. MMIO accessors should be used to access MMIO regions, preferably the ones that correspond to the size of the register accessed. Let's convert the bulk register copy to writel/readl_relaxed, which is the correct API. Signed-off-by:
-
Marc Zyngier authored
Calling request_irq() followed by disable_irq() is usually a bad idea, specially if the interrupt can be pending, and you're not yet in a position to handle it. This is exactly what happens on my kevin system when rebooting in a second kernel using kexec: Some interrupt is left pending from the previous kernel, and we take it too early, before disable_irq() could do anything. Let's clear the pending interrupts as we initialize the HW, and move the interrupt request after that point. This ensures that we're in a sane state when the interrupt is requested. Cc: stable@vger.kernel.org Signed-off-by:
-
zain wang authored
We currently wait for the panel to mirror our intended PSR state before continuing on both PSR enter and PSR exit. This is really only important to do when we're entering PSR, since we want to be sure the last frame we pushed is being served from the panel's internal fb before shutting down the soc blocks (vop/analogix). This patch changes the behavior such that we only wait for the panel to complete the PSR transition when we're entering PSR, and to skip verification when we're exiting. Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Sonny Rao <sonnyrao@chromium.org> Signed-off-by:
zain wang <wzz@rock-chips.com> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Signed-off-by:
Thierry Escande <thierry.escande@collabora.com> Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by:
Archit Taneja <architt@codeaurora.org> Signed-off-by:
-
Arnd Bergmann authored
Like many other panel drivers, this one fails to build when backlight support is disabled: drivers/gpu/drm/panel/panel-raydium-rm68200.o: In function `rm68200_probe': panel-raydium-rm68200.c:(.text+0x14a): undefined reference to `devm_of_find_backlight' This adds the appropriate dependency. Note that while include/linux/backlight.h provides a stub inline when backlight support is not enabled, this isn't enough to deal with the case where backlight support is built as a module but the panel driver is built-in, in which case linking will still fail as above. One way to avoid this is to add a dependency such as this: depends on BACKLIGHT_CLASS_DEVICE || BACKLIGHT_CLASS_DEVICE=n but that is rather complex and misses the point that the panel support is mostly useless without backlight support. Fixes: 2b7ed18b ("drm/panel: Add support for Raydium RM68200 panel driver") Signed-off-by:Arnd Bergmann <arnd@arndb.de> [treding@nvidia.com: clarify the need for the dependency] Signed-off-by:
Thierry Reding <treding@nvidia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180313210015.3344380-1-arnd@arndb.de
-
zain wang authored
Add a lock to vop to avoid disabling the crtc while waiting for a line flag while enabling psr. If we disable in the middle of waiting for the line flag, we'll end up timing out or worse. Signed-off-by:
-
zain wang authored
We would meet a short black screen when exit PSR with the full link training, In this case, we should use fast link train instead of full link training. Signed-off-by:
-
zain wang authored
There is a race between AUX CH bring-up and enabling bridge which will cause link training to fail. To avoid hitting it, don't change psr state while enabling the bridge. Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com> Cc: Sean Paul <seanpaul@chromium.org> Signed-off-by:
Caesar Wang <wxt@rock-chips.com> [seanpaul fixed up the commit message a bit and renamed *_supported to *_enabled] Signed-off-by:
-
Sean Paul authored
Now that the spinlocks and timers are gone, we can remove the psr worker located in rockchip's analogix driver and do the enable/disable directly. This should simplify the code and remove races on disable. Cc: 征增 王 <wzz@rock-chips.com> Cc: Stéphane Marchesin <marcheu@chromium.org> Signed-off-by:
-
Yakir Yang authored
Make sure the request PSR state takes effect in analogix_dp_send_psr_spd() function, or print the sink PSR error state if we failed to apply the requested PSR setting. Cc: 征增 王 <wzz@rock-chips.com> Cc: Stéphane Marchesin <marcheu@chromium.org> Signed-off-by:
Yakir Yang <ykk@rock-chips.com> [seanpaul changed timeout loop to a readx poll] Signed-off-by:
-
Giulio Benetti authored
Handle both positive and negative dclk polarity, according to bus_flags, taking care of this: On A20 and similar SoCs, the only way to achieve Positive Edge (Rising Edge), is setting dclk clock phase to 2/3(240°). By default TCON works in Negative Edge(Falling Edge), this is why phase is set to 0 in that case. Unfortunately there's no way to logically invert dclk through IO_POL register. The only acceptable way to work, triple checked with scope, is using clock phase set to 0° for Negative Edge and set to 240° for Positive Edge. On A33 and similar SoCs there would be a 90° phase option, but it divides also dclk by 2. This patch is a way to avoid quirks all around TCON and DOTCLOCK drivers for using A33 90° phase divided by 2 and consequently increase code complexity. Signed-off-by:
Giulio Benetti <giulio.benetti@micronovasrl.com> Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/1520963677-124239-1-git-send-email-giulio.benetti@micronovasrl.com
-
Giulio Benetti authored
mode_valid function is missing for lvds. Add it making it pointed by encoder helper functions. Signed-off-by:
-
Giulio Benetti authored
mode_valid function must be connected to encoder. Otherwise it could get not be called by drm in the case there's a bridge connected to encoder instead of a panel. Move mode_valid function pointer to encoder helper functions, changing its prototype according to encoder helper function pointer. Signed-off-by:
-
- 13 Mar, 2018 11 commits
-
-
Lukas Wunner authored
Commit 5addcf0a ("nouveau: add runtime PM support (v0.9)") prevents runtime suspend of the GPU if its integrated HDA controller is not bound to a driver. The rationale appears to be that probing the HDA fails if the GPU is in D3cold. However we now use a device link to ensure that the GPU is runtime resumed while the HDA controller is probed, rendering this safety measure obsolete. Remove it. Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by:
Peter Wu <peter@lekensteyn.nl> Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro Signed-off-by:
Lukas Wunner <lukas@wunner.de> Link: https://patchwork.freedesktop.org/patch/msgid/77e0ab74f3377ea9b6acf8fab624acfb4f7dbeca.1520068884.git.lukas@wunner.de
-
Lukas Wunner authored
When switching the display on muxed machines, we currently force the HDA controller into runtime suspend on the previously used GPU and into runtime active state on the newly used GPU. That's unnecessary if the GPU uses driver power control, we can just let the audio device autosuspend or autoresume as it sees fit. Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Alex Deucher <alexander.deucher@amd.com> Reviewed-by:
-
Lukas Wunner authored
Back in 2013, runtime PM for GPUs with integrated HDA controller was introduced with commits 0d69704a ("gpu/vga_switcheroo: add driver control power feature. (v3)") and 246efa4a ("snd/hda: add runtime suspend/resume on optimus support (v4)"). Briefly, the idea was that the HDA controller is forced on and off in unison with the GPU. The original code is mostly still in place even though it was never a 100% perfect solution: E.g. on access to the HDA controller, the GPU is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there are no provisions to keep it resumed until access to the HDA controller has ceased: The GPU autosuspends after 5 seconds, rendering the HDA controller inaccessible. Additionally, a kludge is required when hda_intel.c probes: It has to check whether the GPU is powered down (check_hdmi_disabled()) and defer probing if so. However in the meantime (in v4.10) the driver core has gained a feature called device links which promises to solve such issues in a clean way: It allows us to declare a dependency from the HDA controller (consumer) to the GPU (supplier). The PM core then automagically ensures that the GPU is runtime resumed as long as the HDA controller's ->probe hook is executed and whenever the HDA controller is accessed. By default, the HDA controller has a dependency on its parent, a PCIe Root Port. Adding a device link creates another dependency on its sibling: PCIe Root Port ^ ^ | | | | HDA ===> GPU The device link is not only used for runtime PM, it also guarantees that on system sleep, the HDA controller suspends before the GPU and resumes after the GPU, and on system shutdown the HDA controller's ->shutdown hook is executed before the one of the GPU. It is a complete solution. Using this functionality is as simple as calling device_link_add(), which results in a dmesg entry like this: pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0 The code for the GPU-governed audio power management can thus be removed (except where it's still needed for legacy manual power control). The device link is added in a PCI quirk rather than in hda_intel.c. It is therefore legal for the GPU to runtime suspend to D3cold even if the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL is not enabled, for accesses to the HDA controller will cause the GPU to wake up regardless if they're occurring outside of hda_intel.c (think config space readout via sysfs). Contrary to the previous implementation, the HDA controller's power state is now self-governed, rather than GPU-governed, whereas the GPU's power state is no longer fully self-governed. (The HDA controller needs to runtime suspend before the GPU can.) It is thus crucial that runtime PM is always activated on the HDA controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which is the default), lest the GPU stays awake. This is achieved by setting the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME flag on the HDA controller. A side effect is that power consumption might be reduced if the GPU is in use but the HDA controller is not, because the HDA controller is now allowed to go to D3hot. Before, it was forced to stay in D0 as long as the GPU was in use. (There is no reduction in power consumption on my Nvidia GK107, but there might be on other chips.) The code paths for legacy manual power control are adjusted such that runtime PM is disabled during power off, thereby preventing the PM core from resuming the HDA controller. Note that the device link is not only added on vga_switcheroo capable systems, but for *any* GPU with integrated HDA controller. The idea is that the HDA controller streams audio via connectors located on the GPU, so the GPU needs to be on for the HDA controller to do anything useful. This commit implicitly fixes an unbalanced runtime PM ref upon unbind of hda_intel.c: On ->probe, a runtime PM ref was previously released under the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but on ->remove a runtime PM ref was only acquired under the first of those conditions. Thus, binding and unbinding the driver twice on a vga_switcheroo capable system caused the runtime PM refcount to drop below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag is now always set if use_vga_switcheroo is true. For more information on device links please refer to: https://www.kernel.org/doc/html/latest/driver-api/device_link.html Documentation/driver-api/device_link.rst Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Takashi Iwai <tiwai@suse.de> Reviewed-by:
-
Lukas Wunner authored
If DRM drivers use runtime PM, they currently notify vga_switcheroo whenever they ->runtime_suspend or ->runtime_resume to update vga_switcheroo's internal power state tracking. That's essentially a duplication of a functionality performed by the PM core as it already tracks the GPU's power state and vga_switcheroo can always query it. Introduce a new internal helper vga_switcheroo_pwr_state() which does just that if runtime PM is used, or falls back to vga_switcheroo's internal power state tracking if manual power control is used. Drop a redundant power state check in set_audio_state() while at it. This removes one of the two purposes of the notification mechanism implemented by vga_switcheroo_set_dynamic_switch(). The other one is power management of the audio device and we'll remove that next. Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by:
-
Lukas Wunner authored
When cutting power to a GPU and its integrated HDA controller, their cached current_state should be updated to D3cold to reflect reality. We currently rely on the DRM and HDA drivers to do that, however: - The HDA driver updates the current_state in azx_vs_set_state(), which will no longer be called with driver power control once we migrate to device links. (It will still be called with manual power control.) - If the HDA device is not bound, its current_state remains at D0 even though the GPU driver may decide to go to D3cold. - The DRM drivers update the current_state using pci_set_power_state() which can't put the device into a deeper power state than D3hot if the GPU is not deemed power-manageable by the platform (even though it *is* power-manageable by some nonstandard means, such as a _DSM). Centralize updating the current_state of the GPU and HDA controller in vga_switcheroo's ->runtime_suspend hook to overcome these deficiencies. The GPU and HDA controller are two functions of the same PCI device (VGA class device on function 0 and audio device on function 1) and no other PCI devices reside on the same bus since this is a PCIe point-to-point link, so we can just walk the bus and update the current_state of all devices. On ->runtime_resume, the HDA controller is in D0uninitialized state. Resume to D0active and then let it autosuspend as it sees fit. Note that vga_switcheroo_init_domain_pm_ops() is not supposed to be called by hybrid graphics laptops which power down the GPU via its root port's _PR3 resources and consequently vga_switcheroo_runtime_suspend() is not used. On those laptops, the root port is power-manageable by the platform (instead of by a nonstandard means) and the current_state is therefore updated by the PCI core through the following call chain: pci_set_power_state() __pci_complete_power_transition() pci_bus_set_current_state() Resuming to D0active happens through: pci_set_power_state() __pci_start_power_transition() pci_wakeup_bus() Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: -
Lukas Wunner authored
There are PCI devices which are power-manageable by a nonstandard means, such as a custom ACPI method. One example are discrete GPUs in hybrid graphics laptops, another are Thunderbolt controllers in Macs. Such devices can't be put into D3cold with pci_set_power_state() because pci_platform_power_transition() fails with -ENODEV. Instead they're put into D3hot by pci_set_power_state() and subsequently into D3cold by invoking the nonstandard means. However as a consequence the cached current_state is incorrectly left at D3hot. What we need to do is walk the hierarchy below such a PCI device on powerdown and update the current_state to D3cold. On powerup the PCI device itself and the hierarchy below it is in D0uninitialized, so we need to walk the hierarchy again and wake all devices, causing them to be put into D0active and then letting them autosuspend as they see fit. To this end make pci_wakeup_bus() & pci_bus_set_current_state() public so PCI drivers don't have to reinvent the wheel. Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
-
Rafael J. Wysocki authored
We leave PCI devices not bound to a driver in D0 during runtime suspend. But they may have a parent which is bound and can be transitioned to D3cold at runtime. Once the parent goes to D3cold, the unbound child may go to D3cold as well. When the child goes to D3cold, its internal state, including configuration of BARs, MSI, ASPM, MPS, etc., is lost. One example are recent hybrid graphics laptops which cut power to the discrete GPU when the root port above it goes to ACPI power state D3. Users may provoke this by unbinding the GPU driver and allowing runtime PM on the GPU via sysfs: The PM core will then treat the GPU as "suspended", which in turn allows the root port to runtime suspend, causing the power resources listed in its _PR3 object to be powered off. The GPU's BARs will be uninitialized when a driver later probes it. Another example are hybrid graphics laptops where the GPU itself (rather than the root port) is capable of runtime suspending to D3cold. If the GPU's integrated HDA controller is not bound and the GPU's driver decides to runtime suspend to D3cold, the HDA controller's BARs will be uninitialized when a driver later probes it. Fix by saving and restoring config space over a runtime suspend cycle even if the device is not bound. Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> [lukas: add commit message, bikeshed code comments for clarity] Signed-off-by:
-
Neil Armstrong authored
This patch adds support for DMT display modes over HDMI. The modes timings configurations are from the Amlogic Vendor linux tree and tested over multiples monitors. Previously only a selected number of CEA modes were supported. Only these following modes are supported with these changes: - 640x480@60Hz - 800x600@60Hz - 1024x768@60Hz - 1152x864@75Hz - 1280x1024@60Hz - 1600x1200@60Hz - 1920x1080@60Hz The associated code to handle the clock rates is also added. Acked-by:
Jerome Brunet <jbrunet@baylibre.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/1520935670-14187-1-git-send-email-narmstrong@baylibre.com
-
Christophe JAILLET authored
If one of these functions fail, we whould free 'drm', as alreadry done in the other error handling paths, below and above. Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
-
Christophe JAILLET authored
According to 'drivers/gpu/drm/drm_drv.c', 'drm_dev_unref()' is just a compatibility alias for 'drm_dev_put()'. So use the latter instead. Signed-off-by:
-
Christophe JAILLET authored
'drm_vblank_init()' can fail. So handle this (unlikely) error. Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by:
-
- 12 Mar, 2018 12 commits
-
-
Ville Syrjälä authored
Put an empty line between the variable declarations and the code, and use tabs for alignment. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180305144919.2881-3-ville.syrjala@linux.intel.comAcked-by:
-
Christoph Fritz authored
This patch adds support for AUO G104SN02 V2 800x600 10.4" panel to DRM simple panel driver. Signed-off-by:
Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by:
Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Wei Yongjun authored
Fixes the following sparse warnings: drivers/gpu/drm/panel/panel-ilitek-ili9322.c:182:12: warning: symbol 'ili9322_inputs' was not declared. Should it be static? drivers/gpu/drm/panel/panel-ilitek-ili9322.c:343:28: warning: symbol 'ili9322_regmap_config' was not declared. Should it be static? Also change ili9322_inputs to 'const char * const' to avoid chackpatch warning. Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
jan.tuerk@emtrion.com authored
emtrion is a system integrator and manufacturer of embedded systems. Website: https://www.emtrion.deSigned-off-by:
Jan Tuerk <jan.tuerk@emtrion.com> Reviewed-by:
Andreas Färber <afaerber@suse.de> Acked-by:
-
Philippe CORNU authored
Add SPDX identifiers to OriseTech OTM8009a panel driver. Signed-off-by:
Philippe Cornu <philippe.cornu@st.com> Signed-off-by:
-
Baruch Siach authored
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Reviewed-by:
-
Jagan Teki authored
This adds support for the Kaohsiung Opto-Electronics., TX31D200VM0BAA 12.3" HSXGA LVDS panel, which can be supported by the simple panel driver. Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Reviewed-by:
-
Philippe CORNU authored
Add support for the optional power-supply. Note: A "dummy regulator" is returned by devm_regulator_get() if the optional regulator is not present in the device tree, simplifying the source code when enabling/disabling the regulator. Signed-off-by:
Yannick Fertré <yannick.fertre@st.com> Signed-off-by:
-
Philippe CORNU authored
Some boards use a dedicated voltage regulator for this panel. Add & document this related optional power-supply property. Signed-off-by:
-
Sean Paul authored
Convert the sharp lq123p1jx31 from using a fixed mode to specifying a display timing with min/typ/max values. This allows us to capture the timings set forth in the datasheet as well as the additional values that we've cleared with the display vendor to avoid interference with the digitizer on the Samsung Chromebook Plus (kevin). A follow-on patch will specify the override mode for kevin devices. Changes in v2: - None Changes in v3: - None Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: linux-rockchip@lists.infradead.org Signed-off-by:
-
Sean Paul authored
In preparation for a new subnode section in a follow-on patch, add explicit headings to the existings sections for simple-panel. Changes in v2: - Added Changes in v3: - None Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: linux-rockchip@lists.infradead.org Signed-off-by:
-
Sean Paul authored
Add a note in the documentation explaining when it's appropriate to use the display-timings subnode on its own, as well as the preferred name to use (panel-timing). Changes in v3: - Added Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: linux-rockchip@lists.infradead.org Signed-off-by:
-
