- 14 Jun, 2016 2 commits
-
-
Hans de Goede authored
The comment is wrong, glue is devm_kzalloc-ed mem attached to the "allwinner,sun4i-a10-musb" compatible platform-dev. Where as glue->musb_pdev is a newly created "musb-hdrc" platform-dev. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> [b-liu@ti.com: revise subject prefix] Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hans de Goede authored
Stop using the return value of platform_device_register_full() to get to the struct musb in sunxi_musb_work(). If a gadget has been registered (insmod-ed) before the musb driver, then musb_start will get called from the musb_core probe function and sunxi_musb_work() may run before platform_device_register_full() has returned. Instead store a pointer to struct musb in struct sunxi_glue when sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets called before sunxi_musb_work() can run. Signed-off-by:
-
- 11 Jun, 2016 1 commit
-
-
Greg Kroah-Hartman authored
Merge tag 'phy-for-4.7-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus Kishon writes: phy: for 4.7-rc *) Fix compiler warning in exynos-mipi-video *) Fix in ti-pipe3 PHY to program the DPLL even if it was already locked Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com>
-
- 08 Jun, 2016 7 commits
-
-
Srinivas Kandagatla authored
This patch protects system from crashing at shutdown in cases where usb host is not added yet from OTG controller driver. As ehci_setup() not done yet, so stop accessing registers or variables initialized as part of ehci_setup(). The use case is simple, for boards like DB410c where the usb host or device functionality is decided based on the micro-usb cable presence. If the board boots up with micro-usb connected, the OTG driver like echi-msm would not add the usb host by default. However a system shutdown would go and access registers and uninitialized variables, resulting in below crash. Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = ffffffc034581000 [00000008] *pgd=0000000000000000, *pud=0000000000000000 CPU: 2 PID: 1957 Comm: reboot Not tainted 4.6.0+ #99 task: ffffffc034bc0000 ti: ffffffc0345cc000 task.ti: ffffffc0345cc000 PC is at ehci_halt+0x54/0x108 LR is at ehci_halt+0x38/0x108 pc : [<ffffff800869837c>] lr : [<ffffff8008698360>] pstate: a00001c5 sp : ffffffc0345cfc60 x29: ffffffc0345cfc60 x28: ffffffc0345cc000 x27: ffffff8008a4d000 x26: 000000000000008e x25: ffffff8008d86cb0 x24: ffffff800908b040 x23: ffffffc036068870 x22: ffffff8009d0a000 x21: ffffffc03512a410 x20: ffffffc03512a410 x19: ffffffc03512a338 x18: 00000000000065ba x17: ffffff8009b16b80 x16: 0000000000000003 x15: 00000000000065b9 x14: 00000000000065b6 x13: 0000000000000000 x12: 0000000000000000 x11: 000000000000003d x10: ffffffc0345cf9e0 x9 : 0000000000000001 x8 : ffffffc0345cc000 x7 : ffffff8008698360 x6 : 0000000000000000 x5 : 0000000000000080 x4 : 0000000000000001 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000008 x0 : ffffffc034bc0000 Process reboot (pid: 1957, stack limit = 0xffffffc0345cc020) Stack: (0xffffffc0345cfc60 to 0xffffffc0345d0000) fc60: ffffffc0345cfc90 ffffff8008698448 ffffffc03512a338 ffffffc03512a338 fc80: ffffffc03512a410 ffffff8008a3bbfc ffffffc0345cfcc0 ffffff8008698548 fca0: ffffffc03512a338 ffffffc03512a000 ffffffc03512a410 ffffff8009d0a000 fcc0: ffffffc0345cfcf0 ffffff800865d2bc ffffffc036068828 ffffffc036068810 fce0: ffffffc036003810 ffffff800853f43c ffffffc0345cfd00 ffffff800854338c fd00: ffffffc0345cfd10 ffffff800853f45c ffffffc0345cfd60 ffffff80080e0f48 fd20: 0000000000000000 0000000001234567 ffffff8008f8c000 ffffff8008f8c060 fd40: 0000000000000000 0000000000000015 0000000000000120 ffffff80080e0f30 fd60: ffffffc0345cfd70 ffffff80080e1020 ffffffc0345cfd90 ffffff80080e12fc fd80: 0000000000000000 0000000001234567 0000000000000000 ffffff8008085e70 fda0: 0000000000000000 0000005592905000 ffffffffffffffff 0000007f79daf1cc fdc0: 0000000000000000 0000000000000000 0000007ffcbb1198 000000000000000a fde0: 00000055928d3f58 0000000000000001 ffffffc034900000 00000000fffffffe fe00: ffffffc034900000 0000007f79da902c ffffffc0345cfe40 ffffff800820af38 fe20: 0000000000000000 0000007ffcbb1078 ffffffffffffffff ffffff80081e9b38 fe40: ffffffc0345cfe60 ffffff80081eb410 ffffffc0345cfe60 ffffff80081eb444 fe60: ffffffc0345cfec0 ffffff80081ec4f4 0000000000000000 0000007ffcbb1078 fe80: ffffffffffffffff 0000000000000015 ffffffc0345cfec0 0000007ffcbb1078 fea0: 0000000000000002 000000000000000a ffffffffffffffff 0000000000000000 fec0: 0000000000000000 ffffff8008085e70 fffffffffee1dead 0000000028121969 fee0: 0000000001234567 0000000000000000 ffffffffffffffff 8080800000800000 ff00: 0000800000808080 0000007ffcbb10f0 000000000000008e fefeff54918cb8c7 ff20: 7f7f7f7fffffffff 0101010101010101 0000000000000010 0000000000000000 ff40: 0000000000000000 0000007f79e33588 0000005592905eb8 0000007f79daf1b0 ff60: 0000007ffcbb1340 0000005592906000 0000005592905000 0000005592906000 ff80: 0000005592907000 0000000000000002 0000007ffcbb1d98 0000005592906000 ffa0: 00000055928d2000 0000000000000000 0000000000000000 0000007ffcbb1aa0 ffc0: 00000055928b819c 0000007ffcbb1aa0 0000007f79daf1cc 0000000000000000 ffe0: fffffffffee1dead 000000000000008e 05ef555057155555 d555544d55d775d3 Call trace: Exception stack(0xffffffc0345cfaa0 to 0xffffffc0345cfbc0) Set corner to 6 faa0: ffffffc03512a338 ffffffc03512a410 ffffffc0345cfc60 ffffff800869837c fac0: ffffff8008114210 0000000100000001 ffffff8009ce1b20 ffffff8009ce5f20 fae0: ffffffc0345cfb80 ffffff80081145a8 ffffffc0345cfc10 ffffff800810b924 fb00: ffffffc0345cc000 00000000000001c0 ffffffc03512a410 ffffff8009d0a000 fb20: ffffffc036068870 ffffff800908b040 ffffff8008d86cb0 000000000000008e fb40: ffffffc034bc0000 0000000000000008 0000000000000000 0000000000000000 fb60: 0000000000000001 0000000000000080 0000000000000000 ffffff8008698360 fb80: ffffffc0345cc000 0000000000000001 ffffffc0345cf9e0 000000000000003d fba0: 0000000000000000 0000000000000000 00000000000065b6 00000000000065b9 [<ffffff800869837c>] ehci_halt+0x54/0x108 [<ffffff8008698448>] ehci_silence_controller+0x18/0xcc [<ffffff8008698548>] ehci_shutdown+0x4c/0x64 [<ffffff800865d2bc>] usb_hcd_platform_shutdown+0x1c/0x24 [<ffffff800854338c>] platform_drv_shutdown+0x20/0x28 [<ffffff800853f45c>] device_shutdown+0xf4/0x1b0 [<ffffff80080e0f48>] kernel_restart_prepare+0x34/0x3c [<ffffff80080e1020>] kernel_restart+0x14/0x74 [<ffffff80080e12fc>] SyS_reboot+0x110/0x21c [<ffffff8008085e70>] el0_svc_naked+0x24/0x28 Code: 53001c42 350000a2 d5033e9f 91002021 (b9000022) Fixes 4bb3cad7 ("usb: host: ehci-msm: Register usb shutdown function") Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by:
Pramod Gurav <pramod.gurav@linaro.org> Tested-by:
Andy Gross <andy.gross@linaro.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Andy Gross authored
This patch fixes a suspend/resume issue where the driver is blindly calling ehci_suspend/resume functions when the ehci hasn't been setup. This results in a crash during suspend/resume operations. Signed-off-by:
-
Geert Uytterhoeven authored
Submitters of device tree binding documentation may forget to CC the subsystem maintainer if this is missing. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Signed-off-by:
-
Thierry Reding authored
Starting with commit 0b52297f ("reset: Add support for shared reset controls") there is a reference count for reset control assertions. The goal is to allow resets to be shared by multiple devices and an assert will take effect only when all instances have asserted the reset. In order to preserve backwards-compatibility, all reset controls become exclusive by default. This is to ensure that reset_control_assert() can immediately assert in hardware. However, this new behaviour triggers the following warning in the EHCI driver for Tegra: [ 3.365019] ------------[ cut here ]------------ [ 3.369639] WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x16c/0x23c [ 3.382151] Modules linked in: [ 3.385214] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc6-next-20160503 #140 [ 3.392769] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [ 3.399046] [<c010fa50>] (unwind_backtrace) from [<c010b120>] (show_stack+0x10/0x14) [ 3.406787] [<c010b120>] (show_stack) from [<c0347dcc>] (dump_stack+0x90/0xa4) [ 3.414007] [<c0347dcc>] (dump_stack) from [<c011f4fc>] (__warn+0xe8/0x100) [ 3.420964] [<c011f4fc>] (__warn) from [<c011f5c4>] (warn_slowpath_null+0x20/0x28) [ 3.428525] [<c011f5c4>] (warn_slowpath_null) from [<c03cc8cc>] (__of_reset_control_get+0x16c/0x23c) [ 3.437648] [<c03cc8cc>] (__of_reset_control_get) from [<c0526858>] (tegra_ehci_probe+0x394/0x518) [ 3.446600] [<c0526858>] (tegra_ehci_probe) from [<c04516d8>] (platform_drv_probe+0x4c/0xb0) [ 3.455029] [<c04516d8>] (platform_drv_probe) from [<c044fe78>] (driver_probe_device+0x1ec/0x330) [ 3.463892] [<c044fe78>] (driver_probe_device) from [<c0450074>] (__driver_attach+0xb8/0xbc) [ 3.472320] [<c0450074>] (__driver_attach) from [<c044e1ec>] (bus_for_each_dev+0x68/0x9c) [ 3.480489] [<c044e1ec>] (bus_for_each_dev) from [<c044f338>] (bus_add_driver+0x1a0/0x218) [ 3.488743] [<c044f338>] (bus_add_driver) from [<c0450768>] (driver_register+0x78/0xf8) [ 3.496738] [<c0450768>] (driver_register) from [<c010178c>] (do_one_initcall+0x40/0x170) [ 3.504909] [<c010178c>] (do_one_initcall) from [<c0c00ddc>] (kernel_init_freeable+0x158/0x1f8) [ 3.513600] [<c0c00ddc>] (kernel_init_freeable) from [<c0810784>] (kernel_init+0x8/0x114) [ 3.521770] [<c0810784>] (kernel_init) from [<c0107778>] (ret_from_fork+0x14/0x3c) [ 3.529361] ---[ end trace 4bda87dbe4ecef8a ]--- The reason is that Tegra SoCs have three EHCI controllers, each with a separate reset line. However the first controller contains UTMI pads configuration registers that are shared with its siblings and that are reset as part of the first controller's reset. There is special code in the driver to assert and deassert this shared reset at probe time, and it does so irrespective of which controller is probed first to ensure that these shared registers are reset before any of the controllers are initialized. Unfortunately this means that if the first controller gets probed first, it will request its own reset line and will subsequently request the same reset line again (temporarily) to perform the reset. This used to work fine before the above-mentioned commit, but now triggers the new WARN. Work around this by making sure we reuse the controller's reset if the controller happens to be the first controller. Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Thierry Reding authored
There are three EHCI controllers on Tegra SoCs, each with its own reset line. However, the first controller contains a set of UTMI configuration registers that are shared with its siblings. These registers will only be reset as part of the first controller's reset. For proper operation it must be ensured that the UTMI configuration registers are reset before any of the EHCI controllers are enabled, irrespective of the probe order. Commit a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to broken USB") introduced code that ensures the first controller is always reset before setting up any of the controllers, and is never again reset afterwards. This code, however, grabs the wrong reset. Each EHCI controller has two reset controls attached: 1) the USB controller reset and 2) the UTMI pads reset (really the first controller's reset). In order to reset the UTMI pads registers the code must grab the second reset, but instead it grabbing the first. Fixes: a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to broken USB") Acked-by:
Jon Hunter <jonathanh@nvidia.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Sudip Mukherjee authored
parport subsystem has introduced parport_del_port() to delete a port when it is going away. Without parport_del_port() the registered port will not be unregistered. To reproduce and verify the error: Command to be used is : ls /sys/bus/parport/devices 1) without the device attached there is no output as there is no registered parport. 2) Attach the device, and the command will show "parport0". 3) Remove the device and the command still shows "parport0". 4) Attach the device again and we get "parport1". With the patch applied: 1) without the device attached there is no output as there is no registered parport. 2) Attach the device, and the command will show "parport0". 3) Remove the device and there is no output as "parport0" is now removed. 4) Attach device again to get "parport0" again. Cc: <stable@vger.kernel.org> # 4.2+ Signed-off-by:
Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by:
-
Michał Pecio authored
Since ed_schedule begins with marking the ED as "operational", the ED may be left in such state even if scheduling actually fails. This allows future submission attempts to smuggle this ED to the hardware behind the scheduler's back and without linking it to the ohci->eds_in_use list. The former causes bandwidth saturation and data loss on isoc endpoints, the latter crashes the kernel when attempt is made to unlink such ED from this list. Fix ed_schedule to update ED state only on successful return. Signed-off-by:
Michal Pecio <michal.pecio@gmail.com> Acked-by:
-
- 03 Jun, 2016 1 commit
-
-
Roger Quadros authored
If bootloader has set a wrong DPLL then we must trash those values and re-program it anyways. This fixes USB3 devices not being enumerated on beagle-x15 if usb was started in u-boot. We don't re-program SATA DPLL if it is locked as it was causing SATA failures if device was hotpluged after boot. Reported-by:
Robert Nelson <robertcnelson@gmail.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
- 01 Jun, 2016 29 commits
-
-
Andrew Goodbody authored
Ensure that the endpoint is stopped by clearing REQPKT before clearing DATAERR_NAKTIMEOUT before rotating the queue on the dedicated bulk endpoint. This addresses an issue where a race could result in the endpoint receiving data before it was reprogrammed resulting in a warning about such data from musb_rx_reinit before it was thrown away. The data thrown away was a valid packet that had been correctly ACKed which meant the host and device got out of sync. Signed-off-by:
Andrew Goodbody <andrew.goodbody@cambrionix.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Andrew Goodbody authored
shared_fifo endpoints would only get a previous tx state cleared out, the rx state was only cleared for non shared_fifo endpoints Change this so that the rx state is cleared for all endpoints. This addresses an issue that resulted in rx packets being dropped silently. Signed-off-by:
-
Bin Liu authored
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(), which causes kernel NULL pointer reference oops later when calling cppi41_dma_channel_program(). Fixes: 069a3fd1 (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c part1) Cc: <stable@vger.kernel.org> # v4.2+ Reported-by:
Matwey V. Kornilov <matwey@sai.msu.ru> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Bin Liu authored
If the session bit was not set in the backup of devctl register, restoring devctl would clear the session bit. Therefor, only restore devctl register when the session bit was set in the backup. This solves the device enumeration failure in otg mode exposed by commit 56f487c7 (PM / Runtime: Update last_busy in rpm_resume). Cc: <stable@vger.kernel.org> # v4.2+ Signed-off-by:
-
Tony Lindgren authored
We need to check the state for the PHY with delayed_work as otherwise MUSB will get confused and idles immediately. Signed-off-by:
-
Tony Lindgren authored
There's no longer any need for custom initcall level for musb. Signed-off-by:
-
Tony Lindgren authored
With the pull up being handled with delayed work, we can now finally remove pm_runtime_set_irq_safe that blocks the MUSB glue from idling. Signed-off-by:
-
Tony Lindgren authored
With PM runtime behaving, these are all now unnecessary. Doing pm_runtime_get(musb->controller) will keep the parent glue layer also active. Signed-off-by:
-
Tony Lindgren authored
At least on n900 we have phy-twl4030-usb only generating cable interrupts, and then have a separate USB PHY. In order for musb to know the real cable status, we need to clear any cached state until musb is ready. Otherwise the cable status interrupts will get just ignored if the status does not change from the initial state. To do this, let's add a return value to musb_mailbox(), and reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause a bit of churn here, I should have added that already last time patching musb_mailbox(). Signed-off-by:
-
Tony Lindgren authored
At least 2430 glue layer pulls d+ high on start up even if there are no gadgets configured. This is bad at least for anything using a separate battery charger chip as it can confuse the charger detection. Let's fix the issue by removing the bogus glue layer code tinkering with the SESSION bit. As pointed out Bin Liu <b-liu@ti.com> and Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>, the SESSION bit just starts host mode if ID pin is grounded, and starts the srp is ID pin is floating. So without the ID pin changing, it's unable to force musb mode to anything. And just for starting a host mode, things work fine without this code. Signed-off-by:
-
Tony Lindgren authored
This is no longer needed with PM runtime at least for 2430 glue. We can now rely only on PM runtime and cable detection. The other glue layers can probably remove try_idle too, but that needs to be tested for each platform before doing it. Signed-off-by:
-
Tony Lindgren authored
This simplifies things and allows idling both MUSB and PHY when nothing is configured. Let's just return early from PM runtime if musb is not yet initialized. Let's also warn if PHY is not configured. Signed-off-by:
-
Tony Lindgren authored
We may have drivers loaded but no configured gadgets and MUSB may be in host mode. If gadgets are configured during host mode, PM runtime will get confused. Disable PM runtime from gadget state, and do it based on the cable and last state. Note that we may get multiple cable events, so we need to keep track of the power state. Signed-off-by:
-
Tony Lindgren authored
We have MUSB setting pm_runtime_irq_safe with the following commits: 30a70b02 ("usb: musb: fix obex in g_nokia.ko causing kernel panic") 3e43a072 ("usb: musb: core: add pm_runtime_irq_safe()") Let's fix things to use delayed work so we can remove the pm_runtime_irq_safe. Note that we may want to set this up in a generic way in the gadget framework eventually. Signed-off-by:
-
Tony Lindgren authored
The conditional use of PM runtime does not work properly for musb gadget. On cable disconnect we may not get any USB_EVENT_NONE leaving the PM runtime call unpaired. Let's fix the issue by making sure the PM runtime calls are paired within the functions. The glue layer will take care of the rest. Signed-off-by:
-
Tony Lindgren authored
Let's not tinker with the PM runtime of musb core from the omap2430 wrapper. This allows us to initialize PM runtime for musb core later on instead of doing it in stages. And omap2430 wrapper has no need to for accessing musb core at this point. Note that this does not remove all the PM runtime calls from the glue layer, those will get removed in a later patch. Signed-off-by:
-
Tony Lindgren authored
Let's make the PM runtime use the standard autosuspend calls. Commit 5de85b9d ("PM / runtime: Re-init runtime PM states at probe error and driver unbind") means we must pair use_autosuspend with dont_use_autosuspend and then use put_sync to properly idle the device. Note that we'll be removing the PM runtime calls from the glue layer to the MUSB core in the next patch. And we can also remove the pointless FIXME comment now. Signed-off-by:
-
Tony Lindgren authored
We have remove() already calling shutdown(), so let's drop it and move the code to remove(). No code changes, we'll drop the the FIXME in the following patch with more clean-up. Signed-off-by:
-
Tony Lindgren authored
Looks like at least 2430 glue won't idle reliably with the 200 ms autosuspend delay. This causes deeper idle states being blocked for the whole SoC when disconnecting OTG A cable. Increasing the delay to 500 ms seems to idle both MUSB and the PHY reliably. This is probably because of time needed by the hardware based negotiation between MUSB and the PHY. Signed-off-by:
-
Hans de Goede authored
When the board is powering attached usb devices via the otg port sometimes / on some devices it takes slightly too long for the Vbus detection code in phy-sun4i-usb.c to signal that Vbus is high after enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR interrupt. This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT VBUSERROR interrupts, fixing connection issues in these cases. Signed-off-by:
-
Hans de Goede authored
Move the mode handling to the platform_set_mode callback. Signed-off-by:
-
Sergei Shtylyov authored
Now that the DMA engine check was moved to musb_tx_dma_porgram(), both musb_tx_dma_set_mode_cppi_tusb() and musb_tx_dma_set_mode_mentor() always return 0, so we can make both these functions *void*. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> [b-liu@ti.com: revise subject prefix] Signed-off-by:
-
Sergei Shtylyov authored
Commit 754fe4a9 ("usb: musb: Remove ifdefs for TX DMA for musb_host.c") looks incomplete: the DMA engine checks are done outside the Mentor/UX500 handler but inside the CPPI/TUSB handler. Move the checks out of the CPPI/ TUSB handler into its caller, musb_tx_dma_program(). Signed-off-by:
-
Bin Liu authored
urb->status is set when endpoint csr RXSTALL, H_ERROR, DATAERROR or INCOMPRX bit is set. Those bits mean a broken pipe, so don't start next urb when any of these bits is set by checking urb->status. To minimize the risk of regression, only do so for RX, until we have a test case to understand the behavior of TX. The patch fixes system freeze issue caused by repeatedly invoking RX ISR while removing a usb uart device connected to a hub, in which case the hub has no chance to report the disconnect event due to the kernel is busy in processing the RX interrupt flooding. Fix checkpatch complaint (qh != NULL) as while. Reported-by:
Max Uvarov <muvarov@gmail.com> Tested-by:
Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by:
-
Bin Liu authored
The MUSB Programming Guide states that the driver should clear RXCSR bit2 when the controller sets the bit. Signed-off-by:
-
Hans de Goede authored
I got one of these cards for testing uas with, it seems that with streams it dma-s all over the place, corrupting memory. On my first tests it managed to dma over the BIOS of the motherboard somehow and completely bricked it. Tests on another motherboard show that it does work with streams disabled. Cc: stable@vger.kernel.org Signed-off-by:
-
Alan Stern authored
Several people have reported that UBSAN doesn't like the pointer arithmetic in ehci_hub_control(): u32 __iomem *status_reg = &ehci->regs->port_status[ (wIndex & 0xff) - 1]; u32 __iomem *hostpc_reg = &ehci->regs->hostpc[(wIndex & 0xff) - 1]; If wIndex is 0 (and it often is), these calculations underflow and UBSAN complains. According to the C standard, pointer computations leading to locations outside the bounds of an array object (other than 1 position past the end) are undefined. In this case, the compiler would be justified in concluding the wIndex can never be 0 and then optimizing away the tests for !wIndex that occur later in the subroutine. (Although, since ehci->regs->port_status and ehci->regs->hostpc are both 0-length arrays and are thus GCC extensions to the C standard, it's not clear what the compiler is really allowed to do.) At any rate, we can avoid all these difficulties, at the cost of making the code slightly longer, by not decrementing the index when it is equal to 0. The runtime effect is minimal, and anyway ehci_hub_control() is not on a hot path. Signed-off-by:
Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Reported-by:
Meelis Roos <mroos@linux.ee> Reported-by:
Martin_MOKREJÅ <mmokrejs@gmail.com> Reported-by:
"Navin P.S" <navinp1912@gmail.com> CC: Andrey Ryabinin <ryabinin.a.a@gmail.com> Signed-off-by:
-
Hans de Goede authored
Commit 198de51d ("USB: uas: Limit qdepth at the scsi-host level") removed the scsi_change_queue_depth() call from uas_slave_configure() assuming that the slave would inherit the host's queue_depth, which that commit sets to the same value. This is incorrect, without the scsi_change_queue_depth() call the slave's queue_depth defaults to 1, introducing a performance regression. This commit restores the call, fixing the performance regression. Cc: stable@vger.kernel.org Fixes: 198de51d ("USB: uas: Limit qdepth at the scsi-host level") Reported-by:
Tom Yan <tom.ty89@gmail.com> Signed-off-by:
-
Tom Yan authored
Commit 198de51d ("USB: uas: Limit qdepth at the scsi-host level") made qdepth limit set in host template (`.can_queue = MAX_CMNDS`) redundant. Removing it to avoid confusion. Signed-off-by:
-
