[Why]
new calculated dispclk, dppclk are stored in
context->bw_ctx.bw.dcn.clk.dispclk_khz, dppclk_khz. Current dispclk,
dppclk are from dc->clk_mgr->clks.dispclk_khz. dcn_validate_bandwidth
compute new dispclk, dppclk. dispclk will put in use after
optimize_bandwidth when ramp_up_dispclk_with_dpp is called. There are
two places for dppclk be put in use. One location is the same as the
location as dispclk. Another is within update_dchubp_dpp which happens
between pre_bandwidth and optimize_bandwidth. dppclk updated within
update_dchubp_dpp will cause new clock values of dispclk and dppclk not
be in use at the same time. when clocks are decreased, this may cause
dppclk is lower than current configuration and let pipe stuck. for
example, eDP + external dp, change resolution of DP from 1920x1080x144hz
to 1280x960x60hz.

before change: dispclk = 337889 dppclk = 337889
change mode, dcn_validate_bandwidth calculate
             dispclk = 143122 dppclk = 143122
update_dchubp_dpp be executed before dispclk be updated,
dispclk = 337889, but dppclk use new value dispclk /2 =
168944. this will cause pipe pstate warning issue.

[How]
between pre_bandwidth and optimize_bandwidth, while dispclk is going to
be decreased, keep dppclk = dispclk
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
amdgpu_dm->backlight_caps is for single eDP only. the caps are upddated
for very connector. Real eDP caps will be overwritten by other external
display. For OLED panel, caps->aux_support is set to 1 for OLED pnael.
after external connected, caps+.aux_support is set to 0. This causes
OLED backlight adjustment not work.

[How]
within update_conector_ext_caps, backlight caps will be updated only for
eDP connector.

Cc: stable@vger.kernel.org
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
when ppt disabled, the watermark doesn't get fine tune causing
underflow.

[How]
It is a temporary solution to reduce sr_xxx_time by 3 us when ppt
disable.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies.  Powering down
hardware on boot will ensure SW state is accurate.

[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update *DynamicMetadata variables for providing more flexibility.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: Target power profile mode should be the second parameter of renoir_set_power_profile_mode

A small mistake
Signed-off-by: chen gong <curry.gong@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Prevents a warning in the MST create connector case.

v2: create global fake encoders rather per connector fake encoders
to avoid running out of encoder indices.

v3: use the actual number of crtcs on the asic rather than the max
to conserve encoders.

v4: v3 plus missing hunk I forgot to git add.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1108
Fixes: c6385e50 ("drm/amdgpu: drop legacy drm load and unload callbacks")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

There is a spelling mistake in a DRM_ERROR error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove signaled jobs from job list and ensure the
job was indeed preempted.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

During preemption test for gfx10, it uses kiq to trigger
gfx preemption, which would result in race condition
with flushing TLB for kiq.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Cleanup of phase1 suspend code to reduce unnecessary indentation.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As designed the common code shared among all smu v11 ASCIs go to
smu_v11_0.c. This helps to maintain clear code layers.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This helps to maintain clear code layers and drop unnecessary
parameter.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This helps to maintain clear code layers and drop unnecessary
parameter.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As designed the common code shared among all smu v11 ASCIs go to
smu_v11_0.c. This helps to maintain clear code layers.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Clean code by dropping unnecessary ones.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

By moving them into asic specific file. Since they are really ASIC
specific.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

By calling the target API(asic specific) directly.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

By calling the target APIs directly.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update sienna_cichlid driver if header and related files.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This seemed a typo.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

To avoid s3 faild at the first cycle on renoir platform, it needs to
revert this patch:
drm/amd/display: add mechanism to skip DCN init
Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Ackedy-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCN3 has two gamut remap matrices. When using CSC adjustment the CM
remap is set to bypass and MPCC remap is used. However to bypass CM
some state in the context is modified and not restored correctly
resulting in subsequent calls to disable MPCC remap as well.

[How]
Fix logic for save/restore of remap enable flag when programming MPCC
remap matrix.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Soft hangs occur when FreeSync is engaged since we utilize VUPDATE
(which doesn't fire when holding the pipe lock) to send back vblank
events when FreeSync is active.

[How]
The alternative (working) interrupt source for this mechanism is
VUPDATE_NO_LOCK. We already use this all other DCN revisions so align
dcn30 with those as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable gpu recovery for sienna cichlid by default to trigger
gpu recovery once needed.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove some unused ASIC check logic.
Remove some definition of amdgpu_device which only used by
the removed ASIC check logic.(V2)
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It's impossible to debug shader hangs with soft recovery.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

clang static analysis flags this error

drivers/gpu/drm/radeon/ci_dpm.c:5652:9: warning: Use of memory after it is freed [unix.Malloc]
                kfree(rdev->pm.dpm.ps[i].ps_priv);
                      ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/radeon/ci_dpm.c:5654:2: warning: Attempt to free released memory [unix.Malloc]
        kfree(rdev->pm.dpm.ps);
        ^~~~~~~~~~~~~~~~~~~~~~

problem is reported in ci_dpm_fini, with these code blocks.

	for (i = 0; i < rdev->pm.dpm.num_ps; i++) {
		kfree(rdev->pm.dpm.ps[i].ps_priv);
	}
	kfree(rdev->pm.dpm.ps);

The first free happens in ci_parse_power_table where it cleans up locally
on a failure.  ci_dpm_fini also does a cleanup.

	ret = ci_parse_power_table(rdev);
	if (ret) {
		ci_dpm_fini(rdev);
		return ret;
	}

So remove the cleanup in ci_parse_power_table and
move the num_ps calculation to inside the loop so ci_dpm_fini
will know how many array elements to free.

Fixes: cc8dbbb4 ("drm/radeon: add dpm support for CI dGPUs (v2)")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When I update the latest kernel, I see the following "____ptrval____" boot
messages.

[    1.872600] radeon 0000:01:05.0: fence driver on ring 0 use gpu addr 0x0000000048000c00 and cpu addr 0x(____ptrval____)
[    1.879095] radeon 0000:01:05.0: fence driver on ring 5 use gpu addr 0x0000000040056038 and cpu addr 0x(____ptrval____)

Both radeon_fence_driver_start_ring() and amdgpu_fence_driver_start_ring()
have the similar issue, there exists the following two methods to solve it:
(1) Use "%pK" instead of "%p" so that the CPU address can be printed when
the kptr_restrict sysctl is set to 1.
(2) Just completely drop the CPU address suggested by Christian, because
the CPU address was useful in the past, but isn't any more. We now have a
debugfs file to read the current fence values.

Since the CPU address is not much useful, just remove the debug info about
CPU address.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
To support inbox1 in CW4 we need to actually program CW4 instead of
region 4 for newer firmware.

This is done correctly on DCN20/DCN21 but this code wasn't added to
DCN30.

[How]
Copy over the missing code. It doesn't need address translation since
DCN30 uses virtual addressing.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in mmhub v9.4.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in mmhub v2.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in mmhub v1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in gfxhub v2.1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in gfxhub v2.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in gfxhub v1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in VCN2/JEPG2. They are for the same ASIC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in UVD7/VCE4. They are for the same ASIC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of
hardcode in VCN1/JEPG1. They are for the same ASIC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch updates to use register distance member instead of hardcode
in GMC10.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>