- 25 Oct, 2010 6 commits
-
-
Hyuk Lee authored
This patch adds support HSMMC for S5PV310(SMDKV310) and S5PC210(SMDKC210). Signed-off-by:
Hyuk Lee <hyuk1.lee@samsung.com> Signed-off-by:
Jeongbae Seo <jeongbae.seo@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Hyuk Lee authored
This patch adds initialization HSMMC device information. And HSMMC platform data like card detect, data bus width and capability is configured. Signed-off-by:
-
Hyuk Lee authored
This patch adds support HSMMC for S5PV310 and S5PC210 and setup for HSMMC host controller and also related GPIO. At most 4 channel can be used at the same time. A user can configure SDHCI data bus as 8bit or 4bit. Signed-off-by:
-
Kukjin Kim authored
This patch clean up the GPIO code and removes useless GPIO addresses. It can be calculated with offset, the 'base' member of s3c_gpio_chip is also initialized in the init function. Signed-off-by: -
Kukjin Kim authored
-
Kukjin Kim authored
When merged patches, missed IRQ_EINT_BIT() definition from commit ea31fd43 (ARM: S5PV210: Add Power Management Support). The IRQ_EINT_BIT() is used in the Power Management operation (plat-samsung/pm.c). Signed-off-by:
-
- 23 Oct, 2010 28 commits
-
-
Mark Brown authored
When converting to use s3c_gpio_cfgpin_range() the function for the IISv4 block appears to have been typoed as 4 (the keypad) rather than 5 as it should be. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Kukjin Kim authored
This patch changes code setting special-function and no pull-up to use the s3c_gpio_cfgrange_nopull() wrapper. NOTE: This is for missed things from the previous patch. Signed-off-by: -
Kukjin Kim authored
This patch changes code setting special-function and no pull-up to use the s3c_gpio_cfgrange_nopull() wrapper. NOTE: This is for missed things from the previous patch. Signed-off-by: -
Kukjin Kim authored
This patch changes code setting special-function and no pull-up to use the s3c_gpio_cfgrange_nopull() wrapper. NOTE: This is for missed things from the previous patch. Signed-off-by: -
Ben Dooks authored
Change code setting special-function and no pull-up to use the s3c_gpio_cfgrange_nopull() wrapper. Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
-
Ben Dooks authored
Change code setting special-function and no pull-up to use the s3c_gpio_cfgrange_nopull() wrapper. Signed-off-by:
-
Ben Dooks authored
Change code setting special-function and no pull-up to use the s3c_gpio_cfgrange_nopull() wrapper. Signed-off-by:
-
Ben Dooks authored
A number of the SDHCI code configure a GPIO to a special function and remove any pull-up, so add s3c_gpio_cfgrange_nopull() as a wrapper to the s3c_gpio_cfgall_range() to make the code that calls it fit on one line. Signed-off-by:
-
Kukjin Kim authored
This patch changes the code setting range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgpin_range(). NOTE: This is for missed things from the previous patch. Signed-off-by: -
Kukjin Kim authored
This patch changes the code setting range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgpin_range(). NOTE: This is for missed things from the previous patch. Signed-off-by: -
Kukjin Kim authored
This patch changes the code setting range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgpin_range(). NOTE: This is for missed things from the previous patch. Signed-off-by: -
Kukjin Kim authored
This patch changes the code setting range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgpin_range(). NOTE: This is for missed things from the previous patch. Signed-off-by: -
Kukjin Kim authored
Change the code setting a range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgall_range(). Signed-off-by: -
Ben Dooks authored
Change the code setting a range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgall_range(). Mop up a few missed s3c_gpio_cfgpin_range() changes. Signed-off-by:
-
Ben Dooks authored
Change the code setting a range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgall_range(). Mop up a few missed s3c_gpio_cfgpin_range() changes. Signed-off-by:
-
Kukjin Kim authored
Change the code setting a range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgall_range(). Mop up a few missed s3c_gpio_cfgpin_range() changes. Signed-off-by: -
Kukjin Kim authored
Change the code setting a range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgall_range(). Signed-off-by: -
Ben Dooks authored
Change the code setting a range of GPIO pins' configuration and pull state to use the recently introduced s3c_gpio_cfgall_range(). Mop up a few missed s3c_gpio_cfgpin_range() changes. Signed-off-by:
-
Ben Dooks authored
Add a function to configure a range of GPIOs function and pull in one go, mainly for the SDHCI and framebuffer helpers which tend to do this. Signed-off-by:
-
Kukjin Kim authored
This patch changes the code setting ranges of GPIO pins in mach-s5pv310 using s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range(). Signed-off-by: -
Ben Dooks authored
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range(). Signed-off-by:
-
Ben Dooks authored
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range(). Signed-off-by:
-
Kukjin Kim authored
This patch changes the code setting ranges of GPIO pins in mach-s5p64x0 using s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range(). NOTE: This is for missed things from the previous patch. Signed-off-by: -
Ben Dooks authored
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range(). Signed-off-by:
-
Ben Dooks authored
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range(). Signed-off-by:
-
Ben Dooks authored
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range(). Signed-off-by:
-
Ben Dooks authored
To aide in changing the gpio code, remove the use of pin-specific configs and move to using the S3C_GPIO_SFN() versions. Signed-off-by:
-
Ben Dooks authored
Add s3c_gpio_cfgpin_range() to configure a range of pins to the given value. This is useful for a number of blocks where the pins are in order and saves multiple calls to s3c_gpio_cfgpin(). Signed-off-by:
-
- 20 Oct, 2010 6 commits
-
-
Marek Szyprowski authored
Add required platform definitions for QT602240 touchscreen on I2C2 bus. Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Marek Szyprowski authored
Add required platform definitions for si470x radio device on Samsung Goni board. Signed-off-by:
Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by:
-
Marek Szyprowski authored
Add required platform definitions for S6E63M0 LCD controller on Samsung Goni board. Signed-off-by:
-
Jongpill Lee authored
This patch adds suspend-to-ram support for S5PV210. Note. This patch is confirmed on SMDKV210 and SMDKC110 board. Signed-off-by:
Jongpill Lee <boyko.lee@samsung.com> Signed-off-by:
Sangbeom Kim <sbkim73@samsung.com> Signed-off-by:
-
Sangbeom Kim authored
This patch fixes build error by S3C2410 PM Suspend debug option due to undefined address. Signed-off-by:
-
Marek Szyprowski authored
Samsung S5P SoCs have the same interrupt type defines for both external interrupts and gpio interrupts. This patch removes all duplicates from S5PC100 and S5PV210 specific includes as well as gpio interrupt code and put a common defines to plat/irqs.h NOTE: Do not use this for S5P6440 and S5P6450. Signed-off-by:
-
